Search Documents

By Chris Mark

Fully-grouted roof bolts comprise more than 80% of the primary roof supports used in U.S. coal mines. However, nearly 1,500 MSHA reportable, non-injury roof falls occur each year, and most of these are attributable to failure of the roof bolt system. Anchorage failure is one failure mechanism for fully-grouted bolts. As roof deformation works its way upward, the bolts can become heavily loaded near their upper ends, If the applied load exceeds the anchorage, the bolts will simply pull out. Research dating back 30 yrs indicates that this type of anchorage failure is most likely when the roof rock is weak, just where roof support is most critical. In soft shale or coal roof, the small amount of data available in the literature indicates that 20-30 in of resin anchorage may be required to achieve the full capacity of the bolt. In other words, the "full resistance zone" of a 60 in bolt may actually be just 30-40 in. Despite its potential importance, there is no widely accepted anchorage test for fully grouted bolts. Standard pull tests have sometimes been employed, but they provide no information on the anchorage near the top of the bolt. An alternative, first described more than 25 yrs ago in the U.S., is the short-encapsulation pull test (SEPT). With this test, the bolt is installed with only a short (1 ft or less) tube of resin. In recent years variations of this test have become international standards. This paper describes recent studies using short encapsulation pull tests in the U.S. Tests were conducted in the National Institute for Occupational Safety and Health (NIOSH) Safety Research Coal Mine at Bruceton and at underground mines in Pennsylvania and West Virginia. The study found that the SEPT can be used to make a simple evaluation of resin bolt anchorage. Suggested procedures for conducting SEPT are included. The study also confirmed that poor anchorage can be an issue, particularly where the roof rock is very weak. Some simple techniques for improving anchorage, and thereby the effectiveness of fully grouted bolts, are discussed.

Jan 1, 2002

By Yingxin Zhou

Data from these field studies and previous case study data have been combined to define ultra-dose seam mining environments and relate them to observed failure conditions. A rating system for ultra-close multi- seam design has been developed and field studies have verified the applicability of the design criteria according to geologic structures, lithology and spatial data. This rating system has been combined with design and depth considerations to create a protocol for quantitatively predicting potential damage in ultra-dose seam mining conditions. A brief discussion of the characteristics of ultra-dose seam mining and its related failure mechanisms is also presented

Jan 1, 1990

By Daniel S. Mazzei

This paper will be a general discussion of surface flooding considerations as they affect mining facilities site selection, based primarily on experience with several such problems with which MSHA's Bruceton Technical Support staff has been involved. The detailed analytical procedures used in arriving at engineering solutions of these problems will not he presented here; the emphasis is on drawing attention to this additional aspect of mine design which hitherto has been largely overlooked due to insufficient awareness, information and criteria. The paper's purpose is to stimulate thought and offer guidance concerning the selection of sites for mining facilities in light of the potential for flooding problems caused by surface waters. Flooding by surface waters, would generally not be a serious consideration in areas of relatively low topographical relief, i.e. flat lands, although there are exceptions to this rule, for example, in Western areas where flash flooding is a major concern. Therefore, this discussion will mainly apply to areas where the severity of surface flooding would be amplified by the topography-large, well defined watersheds of considerable relief, i.e. mountainous areas. In these regions, steep valley walls cause any rainfall to flow quickly into the relatively narrow valley bottoms. These valley bottoms provide little flow area during storm conditions, so deep and rapidly flowing streams result.

Jan 1, 1982

By Yoginder Paul Chugh, Jason E. Tinsley

"Over the last five years, the authors have compiled a database of Short Encapsulation Pull Test (SEPT) evaluations from Interior Basin (Basin) coal mines. Typically, SEPT data are analyzed to obtain peak load carrying capacity per unit length of resin encapsulation designated as the ""Grip Factor,"" or GF. In a previous paper, ""An Analysis of Short Encapsulation Bolt Pull Test (SEPT) Data From Interior Basin Coal Mines,"" authors analyzed tangent value of the load-displacement curve as Anchorage Stiffness at 50% (AS-50) of the peak load, or GF value, to assess reinforcement potential of an installed bolt system. This paper attempts to correlate the secant AS VALUES (of SEPT on 6 ft (1.8 m) long installed bolts at a lower load of about four tons from several different mines in the Basin with their MSHA-approved primary support requirements. Since the current regulatory environment requires plan changes dynamically to ensure that roof falls are minimized, the authors hypothesize that the practiced roof control plan must meet the minimum requirement of adequately supporting immediate roof strata. The analyses are based on 181 SEPT studies performed by Minova professionals. Analyses indicate a macrolevel correlation for both roof support density and roof support cost that may have the potential to be used by mine operators to compare their performance with other mines in the area. Limitations of the analyses include ignoring mining depth, mining height and required secondary supports as part of the requirements for a roof control plan. The authors recommend additional analyses to develop this concept further to develop guidelines that can be confidently used by coal companies.INTRODUCTIONPartially- and fully-grouted bolts are extensively used in coal mines for roof support as part of MSHA-approved roof control plans. Since grouted bolts have a larger area of contact with the rock, they can develop much greater anchorage capacity than conventional expansion shell (point-anchored) bolts. Load transfer characteristics and interaction mechanics between steel rebar, grout and rock mass around the bolt hole for grouted bolts are generally assessed in the laboratory or field though short-encapsulation pull tests (SEPT), which have been extensively researched by Aziz and Jalalifar (2005), Aziz (2004a), Serbousek and Signer (1987), Signer (1990), and Mark et al. (2002), among others. In a SEPT, about 12 in. (30 cm) of bolt length is typically encapsulated in resin and a pull test is performed to collect load-displacement data prior to failure and, in some cases, post-failure. A typical load-displacement data set for a bolt is shown in Figure 1. SEPT characteristics are designated by peak load carrying capacity, or grip factor, which is the peak load carrying capacity per unit length of resin encapsulation. SEPT is routinely used to assess anchorage performance characteristics of different lithologies overlying a coal seam to identify type of bolt, bolt diameter, length and spacing across and along an excavation. Anchorage stiffness, or AS, at any load may also be calculated as the tangent or secant value of the slope of the load displacement curve at a particular load level. Anchorage Stiffness characteristics of bolts from SEPT data have typically not been considered in any depth until recently (Chugh et al., 2014; Chugh et al., 2015)."

Jan 1, 2016

By Sun Henghu

This paper analyses problems associated with cement based technique in metal mines, and provides a new mining technique of packing the tailing sand and water into solidified material. In the new technique, the cementing agent is a solidifying material containing a high percentage of water and tailing sand. The sand and water solidify into the packed body at the same time. The slurry of the packed body varies widely in concentration and suitability for different mining conditions. It consists of two liquid materials, each composed of a cementing agent, tailing sand and water. The thick liquids are transported to the packing place at the same time. Their pumping property is good; they do not solidify or block up the pipe during transportation. At the packing place, the two liquids are evenly mixed. The mixed liquid flattens out well and its solidifying speed is so fast that it solidifies into a packed body within a very short period of time. The compressed strength of the packed body can reach 1.2-5MPa in one day, which satisfies the requirements of different mining conditions. By using the new mining technique, all the tailing sand can be used again in the packed body and it is low in cost and investment. The mechanisation is easy and thus the working efficiency is increased and the use of labour decreased. Contamination problems caused by excess water drainage under the ground are resolved.

Jan 1, 1992

Virtually all mineable Appalachian coal seams exist in a multi-seam environment. This makes it inevitable that most seams will eventually experience interaction induced ground control and mining problems. Indeed, it has been estimated that every working face will experience interaction effects from previous or current workings at least once during its lifetime (1), and that these problems are considerably exaggerated when seams are in close proximity -- a distance of less than 110 feet. The continued increase in multi-seam problems has resulted in considerable research activities over many years (2,3,4,1). Theoretical analysis, numerical and physical model studies, statistical and empirical analysis of numerous interaction related field data have been applied to multi-seam mining situations and have identified many useful trends and design criteria (4,5,6,7). To fully utilize research results and transfer multi-seam mining technology to field engineers, a design model -- USEAM was constructed (8). This model, designed for close seam under-mining situations, was computerized to facilitate utilization. In the current research, a new computer program "MSEAM" was developed to produce a model for both under- and overmining close seam situations. It is hoped that both of these software packages will aid field engineers in using important interactive design criteria to gain a better understanding of interaction mechanisms. Through advance planning with these programs, detrimental interaction may be avoided and minimized, and occasionally a design can be selected which will allow interaction effects to be utilized to the benefit of mining operations.

Jan 1, 1987

By Swapan Bhattacharya

Section 516 of Public Law (PL) 95-87, commonly known as the Surface Mining Control and Reclamation Act of 1977 (SMCRA), requires that underground coal mine operators must 'adopt measures consistent with known technology in order to prevent subsidence causing material damage to the ex- tent technologically and economically feasible, maximize mine stability, and maintain the value and reasonable foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predict- able and controlled manner..." Implied in the constraints of Section 516 (b) (1 of SMCRA is a determination of what constitutes "material damage" to surface structures and renewable resource lands, and the capacity for sequential land use following underground mining. This Study was undertaken in an attempt to provide quantitative guidelines for estimating material damage to a wide variety of surface structures and renewable resource lands. Surface structures studied included buildings, bridges, railroads, highways. pipe- lines, d~, embankments, and water reservoirs. Damage criteria for buildings developed in this study along with details of the adopted methodology have been presented elsewhere (Bhattacharya et al.) (1). and will not be repeated here. Similar guidelines for renewable resource lands have also been discussed (Singh and Bhattacharya) (2)

Jan 1, 1984

By G. Bucelluni

An essential element of truss bolt installation requires machines to angle a hole in the top of approximately 39° to 45° from its vertical axis. Parameter which inherently effect the drill position are: height, width of truss, physical size of mast, and whether single or dual mast bolting is utilized. The combination of these facets govern the installation procedures required for the bolting cycle. The following illustration with written explanation will demonstrate this concept. See Figure #1. [ ] This model assumes certain fixed criteria which corresponds to a dual mast drill design and a set 41° drill angle. Using the derived formula, the maximum possible seam height for both masts to touch the bottom can be calculated for any given condition by substituting by the appropriate bolt spread distance. [ ] In a high seam application where the mast touching the bottom was considered a requirement, the proposed model demonstrates the advantage of single mast drilling. See Figure #2. [ ]

Jan 1, 1982

By Tim Ross

Slurry injection into mined-out panels is an attractive alternative for disposal of coal preparation plant fines. however, in areas where surface subsidence cannot be tolerated, either by law or necessity to protect surface structures or aquifers, special consideration trust he given to the effect of slurry injection on panel stability. Slurry injection can lead to panel failure and unplanned subsidence by degrading roof, pillar, and floor strength. Water degradation is of particular concern where clay is present in the floor. Recently. unplanned subsidence related to slurry injection occurred at an Indiana room-and-pillar coal mine subject to weak floor conditions. This paper discusses the efforts of the mine operator to determine the causes of the panel failure and to design panels and injection procedures to allow for future economic slurry injection without subsidence. The numerical and empirical/analytical techniques applied give the operator a rational approach to pillar panel design for future injection panels under various cover depths and weak floor conditions.

Jan 1, 1998

By Erdal Unal

In gate roads where supports are subjected to dynamic loading four times due to retreating longwall panels, it is a real challenge to replace the rigid arches with flexible reinforcement systems and yet to provide safety and stability of these openings within better economical limits. The results presented in this paper are based on a three years of research project aimed at developing safe and economical support systems for gate roads in Çayìrhan coal mine. Çayìrhan -Mine Project includes laboratory and field studies, design analysis, pilot scale design applications and performance monitoring. Based on outputs of the design approach developed, four types of bolts, namely, Split Set, Yielding Super Swellex, Sis-Resin, and Fosroc-Resin bolts were installed in a gate road together with widely spaced yielding steel-arches. In order to compare the performance of these flexible support systems and to provide feed back for the design approach, a monitoring program was initiated.

Jan 1, 1993

By Kot F. v. Unrug

In spite of the extensive research and accumulated experience from mining operations, an appropriate pillar design remains an open issue. Due to the shrinking reserve base, present mining operations move to more challenging conditions. There are usually thinner seams and geologic conditions are often unfavorable. For instance, mine roof and floor are weak or deteriorate rapidly when exposed to moisture fluctuations in mine atmosphere. It is common that pillars of current operations are more- squat than several decades ago when the bulk of pillar research have been carried out in thicker seams. The methods of pillars calculations were developed regionally (in particular countries) to suit design needs for the most important seams, from which the majority of coal production was coming (e.g. Pittsburg or Pond Creek seams in the eastern of US). Most of the pillar formulae use similar approach by assigning weights (using constants) to the influence of coal (seam) strength and pillar widthheight ratio on its final strength. That mechanistic approach has sound theoretical base and good data supporting its validity. However, what seems to be missing is a qualification system of the mine conditions, which are outside of the data base or do not comply with the theoretical model applied in pillar strength formulae. This paper attempts to address that issue in two major categories, first when only a drill core data are available, and second during the mine development observations can be made directly on a coal seam. The composition of a coal seam is also addressed, (which often changes rapidly across the reserve), and discussed its influence on pillar's structural performance. In summary a set of practical design rules is presented.

Jan 1, 2005

By Alan A. Campoli

"Pumpable crib support for longwall gates and ventilation bleeder entries is becoming more prevalent in United States coal mines (Figure 1). The pumpable crib selection and spacing design has been greatly refined by the full-scale testing conducted at the National Institute for Occupational Safety and Health (NIOSH) Mine Roof Simulator. The peak load on 24-, 27-, 30-, and 36- inch diameter J-Cribs is, on average, 300, 400, 450, and 650 kips, respectively. Standard J-Cribs have useful deformation of approximately 8 inches. The maximum useful deformation can be extended to 18–20 inches with an exterior reinforcement layer or an interior double wall, for all four J-Crib diameters. J-Crib diameter is primarily limited by a maximum 4.5:1 height-to-diameter aspect ratio. Spacing is controlled by immediate roof stability, anticipated pillar deformation, and roof bolting practice. Approximately 500,000 J-Cribs have been successfully placed in 18 different United States longwall coal mines. The selection and spacing of the J-Crib utilized to date is summarized for each mine.IntroductionLongwall productivity and safety depend on ground stability in gate and ventilation bleeder entries. Numerous support technologies have been developed and employed in United States longwall mines since the 1990s to replace traditional wooden cribbing. Many, if not all, of these technologies have been evaluated at the NIOSH Pittsburgh Research Laboratory since the mid-1990s (Mucho, et al., 1999). The NIOSH Mine Roof Simulator has a 3,000-kip vertical load and 24-inch displacement capacity, which has facilitated in-depth analysis of complex multimaterial support technologies like the pumpable crib. The extreme cost and human exposure risk associated with modern longwall mining prevent the trial and error development that would have been required absent the Mine Roof Simulator research. As a direct result of this research, pumpable cribs are becoming a major component of the standing support industry, providing the peak capacity and extended deformation characteristics necessary for successful gate and bleeder support. Recent research by Zhang, et al. (2012) and others have defined the required performance characteristics."

Jan 1, 2015

A procedure fm the estimation of pilla1 strength is presented where the design of underground coal pillars is emphasized. An analytical approach has been developed, proposing that the effect of end constraints on the pillar strength and the ductile behavior of coal material should be incorporated in the computation of the stability of coal pillars. Bad on this approach, it has been found that end constraint has a significant influence on the pillar strength. The study indicates that when the end constraint is zero the computed strength of the pillar is the same as the unconfiied compressive strength of the coal mass and will not increase with the increase in the width to height ratio. However. when the end constraint is greater than zero the pillar strength will increase exponentially as the width to height ratio increases.

Jan 1, 1990

By Wm. Mark Hart

Under a specific geological condition, roof supporting method, and pillar-entry system, an entry convergence concept may be the most effective means that can be used to effectively indicate the longwall entry stability (i.e. pillar bumps, roof falls, or floor beaver This concept may also be used to verify the effectiveness of the current pillar-entry system and roof supporting method. Furthermore, convergence measured under different mining phases may lead to a better understanding of the longwall mining-induced abutment loads and may be used to estimate stress change in pillars and thus pillar stability. In this paper, a remote entry activity monitoring system was designed; a comprehensive entry convergence monitoring strategy was proposed; thee abutment loading phases in longwall mining were defined; the relationship between roof deflection and stress change in a pillar was derived, and finally the extent and magnitude of the mining-induced abutment loads as well as their impact on entry convergence were discussed using the field data obtained so far.

Jan 1, 1995

By A. K. Bhattacharyya

The excessive displacement of the seam floor in headings (i.e. roadways) called 'floor-heave' is often experienced in the underground mines of the Southern Coalfield of New South Wales. Apart from interfering with the mining operations, the phenomenon could be detrimental to the stability of the pillars left for support leading to an unpredictable increase in the subsidence of the overlying strata. The latter could pose a serious problem, particularly in the design of partial extraction layouts of mining for areas where subsidence is to be controlled. The susceptibility of the floor of different rock materials and thicknesses in a given 'panel and pillar' partial extraction geometry was examined by two-dimensional Finite Element Modelling of the displacements, stresses and failure zones around the excavations. The modelling, assuming elastic behaviour of the materials, indicated that the maximum vertical displacements of the floor increased substantially as the Young's Modulus of the material decreased to less than 7GPa and the thickness of the layer increased. The results also discount the possibility of a properly designed panel and pillar geometry in the Southern Coalfield of New South Wales being unable to adequately control surface subsidence through the pillar, or its core independently of the yielded ribs, penetrating the floor.

Jan 1, 1992

By Chris Mark

The Coal Mine Root Rating (CMRR) was first presented at this Conference nine years ago. Since Its Introduction, the CMRR has been incorporated into many aspects of mine planning. including longwall pillar design, rout support selection, feasibility studies. and extended cut evaluation. It has also become truly international, with involvement in mine designs and funded research projects iii South Africa. Canada. and Australia. The purpose of this paper is to bring the minim community Up to date with recent improvements and applications of the CMRR. The must important new development is a streamlined process for determining the CMRR from exploratory drill core. Just three types of information are Jaw required: Fracture spacing (or RQD) Uniaxial compressive strength for axial Point Load Testing) Diametral Point Load Testing The moisture sensitivity adjustment has also been changed, and new research has related the immersion test to slake durability. Most recently, the CMRR has been implemented in a computer program. which can be obtained from NIOSH free of charge. The program facilitates calculation of the CMRR firm either underground or drill core data. Values from ninny locations can he saved in a single file. and an interface with Autocad allows CMRR contour plots to he integrated 11110 mine planning.

Jan 1, 2002

By Peter Griesenbrock

In German underground coal mining mostly arch and some rectangular roadways are used in the development work. Due to its positive results from numerical and physical modeling techniques as well as good underground experiences, the numbers of rectangular roadways has increased significantly. Today the bolt support - independent of its cross-sectional shape - represents an undeniable support element. During the introduction of new bolt techniques a detailed investigation of the rock and support mechanical effectiveness of bolt support in roadways at all operation stages is of basic importance. This effectiveness can be predicted and verified using different simulation techniques. For the planning of rockbolted roadways two supplementary simulation techniques are presented in this paper. By combination of all available planning tools the best result for planning assurance can be achieved. Keywords: numerical modeling, physical modeling, arched roadway, rectangular roadway, roofbolting, advancing longwall.

Jan 1, 2002

By Axel Preusse

Due to a political decision, German hard coal mining will come to an end in the year 2018. By then, there will have been more than 150 years of industrial grade mining activities. Located in the western part of Germany is one of the most densely populated areas of Europe. Multiple coal seams have embossed the earth?s surface up to 20 meters (21.87 yards), as mining has subsided. The aftercare of hard coal mining will consist of three tasks: groundwater management, polder management, and groundwater treatment. The Ewigkeitslasten (cost in perpetuity) at the current groundwater level has been determined in the past. The actual cash value is calculated to be about 12.4 billion euros (approximately 16.5 billion dollars). The cost of groundwater management is directly related to the groundwater level. Rising groundwater levels will reduce the cost of pumping water. Known effects of rising groundwater are uplift of the surface, emission of methane gas at the surface, higher risk of cave-ins, and contamination of drinking water horizons. Each of those processes produces cost in order to prevent negative consequences (e.g., uncontrolled methane emissions) or to handle reparations (e.g., damages caused by surface uplifts). In the long run, it is the goal to minimize the Ewigkeitslast. As a first step, all cost-generating processes are specified, and a cost type based characterization is performed. The objective of this case study is to identify key parameters to determine the quality of a cost-generating process (proportional cost, fixed amount cost). Afterwards, it is intended to specify the quantitative impacts of each parameter and to set up an optimization model to minimize the overall cost. The quantitatively specified parameters will form the base out of which the optimization model is created.

Jan 1, 2013

By Rusty Mchenry, Craig Dickerson, Robin L. Oldham

"It has been proven that longwall faces can be moved safely and efficiently. However, abutment pressures and poor ground control conditions can halt operations and be hazardous to coal miners. Recently at a mine in Southwestern Pennsylvania, roof material collapsed above shields that created two large voids and caused major challenges for shield recovery. A unique, engineering solution was developed that utilized a modified concrete material to fill the voids, creating stability in the affected area. The many phases of this project included the construction phase, void pumping, cutting out, and bolting of the concrete material. This project eliminated the hazards associated with bolting the recovery face and removing shields in adverse conditions, making it possible for the mine operator to safely complete the longwall move.INTRODUCTIONFrequently in the mining process, especially during the recovery phase, voids above the longwall supports have occurred. These voids are simply roof cavities caused by falling rock strata above the longwall face. Most often, this condition slows down or halts mining operations and creates hazardous work conditions for coal miners. Numerous methods of supporting void areas on longwall faces have been attempted and utilized throughout the mining industry since the advent of the longwall mining system. These methods have utilized many different materials and processes and have included the installation of steel or wooden beams, crib blocks, and various types of roof bolts. However, these methods can be dangerous due to exposure of personnel to the mine voids, falling roof material, and the necessity to handle large amounts of heavy support materials.This paper describes a unique case study in Southwestern Pennsylvania where longwall recovery methods, through two void fills, were successfully completed, eliminating exposure of coal miners to the rock voids above. At the start of this endeavor, normal recovery operations were halted, and hazardous conditions became a concern when the voids were encountered. However, in the interest of safety, the decision was made to try a unique method to completely fill the void from the bottom of the coal seam to the top of the void with a cementitious material and then mine through it. This is in contrast to traditional methods where beams and support materials are used to stabilize the area above and in front of the mine shields, which can expose miners to the void above."

Jan 1, 2015

By P. K. Kaiser

The purpose of deformation monitoring for the evaluation of the stability of underground openings is reviewed briefly and some results from laboratory tests of small tunnels are presented. The ground behaviour is described by comparison with the response of structural systems and illustrated by the data from the testing of small tunnels. It is concluded that the main objective of a deformation monitoring system for stability evaluation is to determine the actual process of deformation and instability in the area surrounding the opening. Only when this process has been established is it possible to use deformation measurements to design support systems or to improve construction or mining procedures. Present monitoring practice is not sufficiently orientated toward the aim of process description.

Jan 1, 1981