Search Documents

By V. I. Ryaboy, V. A. Luknitsky, V. V. Zuyev

The action has been studied of three types of reagents used as intensifiers in grinding copper-molybdenum, sulphide-sheelite, polymetallic and other types of ores, namely N-donor, dispersant, and surface-acting agents. It has been proved that, depending on the type of ore treated, the C (N-donor) and C-170 (dispersant) reagents increase the yield of the principal size fraction of 0.074mm by 8-16% (relative). Consequently, the specific mill capacity improves by 13-21 %. The C and C-170 reagents activate the subsequent flotation stage and are thus beneficial to the mineral recovery. The surface-acting reagents affect the mineral grinding process to a lesser extent. The intensifying action of the reagents is attributed to the effective crushing energy decrease (lower crack-resistance factor) or else to the slime-dispersing effect of the reagents. The pilot-plant test results for the C reagents are given. Both C and C170 reagents are commercially produced and recommended for use at a number of concentrators in Russia, Uzbekistan and Kazakhstan.

Jan 1, 1995

By P. K. Davis

The results of a previous basic study of the flow and design characteristics of the hydrocyclone has shown that a recovery as high as 99% with a product rating of 0.95 can be achieved on a "batch?2 basis with a single, water-only cyclone if it is configured properly. The next logical step was to demonstrate continuous processing of gob for the efficient recovery of coal by means of a laboratory-size demonstration system. A project to design and construct such a single-cyclone system was also sponsored by the U.S. Department of Energy. A recovery of 93% with a product rating of 0.89 was demonstrated. The system design and the data taken are discussed.

Jan 1, 1989

By Ronald D. Hill

Acid mine drainage is the result of the oxidation of pyrite and similar iron sulfide material and the release of iron and sulfuric acid into the environment. In addition to the acid water flowing from underground and surface mines, spoil materials in surface mines are acidic and will not support good vegetative growth; thus erosion is a major problem. Lime and limestone are the major neutralizing agents used to treat these acidic conditions. Lime is the reagent preferred by industry for treating acid discharges, although a few companies use limestone. Agricultural lime- stone is used to "sweeten" acid spoils.

Jan 1, 1974

By P. Otto, G. Borm, Th. Dickmann, F. Amberg, R. Giese

Based on many years experience, the well approved Tunnel Seismic Prediction System (TSP) has been substantially enhanced for online geological prognosis in underground construction. The method provides high resolution seismic images of the rock mass ahead of a tunnel face via an array of standard anchor rods. These contain3D-geophones and can routinely be installed during the excavation process. A further outstanding feature of the system is the newly developed high frequency repetitive seismic source which can easily be fixed at a tunnel boring machine. A user-friendly software package enables online data acquisition, processing, 3D-visualization, and interpretation.

Jan 1, 2001

By D. L. Passmore

The development of microcomputer software that provides an analysis of pit-specific accident and production data for the mining industry is seen as a vital component in a total loss-control system. The Mine Injury Reporting System (MIRS) allows users to access accident and production data prepared by the Health and Safety Technology Center of the Mine Safety and Health Administration of the United States Department of Labor for any particular state and to generate a simple, yet informative, report.

Jan 1, 1988

By S. D. Thompson, L. Adler

Several researchers in the last 20 years have developed computer simulation models for designing coal mine belt systems. A careful review of these reveals that each omitted or oversimplified important factors, especially in belt loading. To remedy this, the coal mine belt capacity simulator (CMBCS) was developed to include various types of probability distributions, delays, and longwall and continuous haulage. CMBCS is computer coded in FORTRAN and employs the Monte Carlo simulation technique. Basically, the model simulates the loading and corresponding flow of coal through a belt system. By recording spillage and belt stoppage statistics for the simulated flow, belt and surge bin capacities can be evaluated. A complete user's guide is available. The modeling and verification of CMBCS are briefly described, and its major advantages and disadvantages are explored.

Jan 1, 1987

Teeter-bed (i.e., hindered-bed) separators are used throughout the mineral processing industry for both classification and density separation. The high capacity and sizing characteristics of these units make them ideal for feed preparation prior to coarse flotation (+0.100 mm) circuits. Teeter-bed separators are typically easy to control with two basic operating parameters including fluidization water rate and bed level. However, data show that these two parameters greatly interact with one another. Given this finding, a high-level automatic control scheme was developed and implemented on a full-scale separator. In addition, dialogue with plant operators has led to several simple changes to an already established design that improves operational and maintenance characteristics.

Jan 1, 2010

By W. Dan Hausel

In previous reports by Hausel et. al., (1979 a, b, and c), Leighton and McCallum (1979), and McCallum (1974;1979), several exploration procedures were examined as to their effectiveness in locating kimberlite intrusives in northern Colorado and southeastern Wyoming, where approximately 90 kimberlites have been recognized within 5 districts (Figure I). Briefly, geological mapping and stream sediment sampling for indic- ative heavy minerals of kimberlite (pyrope garnet, chrome diopside, and magnesian ilmenite) proved to be the two most effective methods in isolating kimberlite occurrences within the granitic terrain of Colorado and Wyoming (Hausel et. al., 1979 a, b, and c; Leighton and McCallum, 1979). Where a kimberlite intrusive is deeply weathered, remote sensing using color and color infrared aerial photography may be a potential reconnaissance tool in kimberlite exploration. The kimberlitic eluvium supports thicker grassy vegetation, and at least one species of grass (the Bluebunch Wheatgrass) is found to grow only within the eluvium. The result is that vegetation in the kimberlitic eluvium is a better infrared reflector than the vegetation in the surrounding granitic soils (Hausel et. al., 1979 b; McCallum, 1974

Jan 1, 1980

By M. Sagisaka

The purpose of this study is to obtain carbon dioxide emissions by copper production systems and quantitative merit to use copper scraps in Japan. Electrolytic copper and sulphuric acid originating from the refining gas are produced in the system. In this study, the inventories such as the fuel consumption of the unit processes and the in-house electricity generation were obtained from published papers and public statistical data. The following observations were made based on the Life Cycle Assessment (LCA) method: (1) Carbon dioxide emissions from the production of electrolytic copper and sulphuric acid in the system are about 1.0 kg and 0.4 kg/kg-product respectively. The carbon dioxide emissions attributable to the transportation of copper concentrate correspond to 20% of the total emission. This emission is higher than that of zinc because the metal content in the concentrate is lower than zinc. (2) The carbon dioxide emissions from the system decrease with the recycling of copper scrap to the converting process because the consumption of copper concentrate is reduced. The reduction is estimated to be 0.18 kg-CO2/kg-Cu at the point of 0.1 kg-scrap/kg-blister Cu. This corresponds to 9% reduction for the present system. However, this recycling leads to the decrease of sulphuric acid by 450x103 tonne at the point. The recycling of scrap should be evaluated not only from the reduction of carbon dioxide emissions, but also in terms of sulphuric acid demands as well as advantage of waste management.

Jan 1, 2003

By Jane Morrison

Permanent magnets are used in most electromechanical and electronic devices to convert electrical to mechanical energy and vice versa. More than fifty are commonly found in the average American home and car. A new species of permanent magnet composed of iron, neodymium, and boron has recently been developed which combines superior magnetic properties with compact size. The reduced size of the magnets has enabled significant new developments in such areas as robotics and consumer electronic, among others. The objective of the present work is to efficiently and economically separate valuable rare earth materials from the relatively worthless iron constituent in NdFeB magnet scrap. Several magnet producers have expressed interest in the development of such a process and have provided information and scrap samples to aid in research. Scrap is generated in a variety of forms from different stages in the processing stream. Pieces of magnetic and non-magnetic metal as well as sludge and ribbon from jet casting must all be treated. Beneficiation techniques have been studied and size distributions developed for the different scrap types. Slag from the casting process is resistant to crushing and may need to be embrittled first, but all other types are amenable to crushing and ball mill grinding using stainless steel balls and water. Tabling was found to be useful in classification of magnet sludge. Two major techniques for separation of rare earths have been studied:

Jan 1, 1990

The Chinese city of Shanghai is one of the fastest growing in the world. To keep up with the growth, two tunnels, three-lanes each, are being built beneath the Yangtze River to connect Shanghai with the Changxing River Island. To complete such a large project, Herrenknecht Tunneling Systems was brought in to construct the largest tunnel boring machine (TBM) in the world. The first Herrenknecht S-317 Mixshield has a diameter of 15.43 m (50.62 ft). It was built to construct one of the two 7.2-km (4.5-mile) tunnels. The tunnels are part of the Changjiang Under River Tunnel Project and will be at depths of up to 65 m (213 ft) beneath the Yangtze River in Shanghai-Pudong. These two tunnels are to be opened to traffic in April 2010, in time for Shanghai to host the World Expo. More than 20 million people live in the Shanghai area. The area itself has been growing at an extremely rapid pace for more than a decade and is in need of more space. The search extended beyond the natural limits of the Yangtze River Delta. As part of its incredible growth, 500 new vehicles are registered every day. The new tunnels will connect the Changxing River Island, with a population of approximately 600,000 people to the road traffic network. A bridge construction will also provide a traffic link between Changxing Island and the large island of Chongming.

Jan 1, 2007

By Harold Wagner, Prakash Donde, Larry H. Heflin

INTRODUCTION The Washington Metropolitan Area Transit Authority is responsible for the planned 166 kilometer (103 mile) Metro rapid rail transit system in Washington, D.C. Some 117 kilometers (72.8 miles) of this system is in operation and contains 30.6 route-kilometers (19 miles) of rock tunneling. To complete the planned system an additional 1.6 kilometers (1.0 miles) of single track tunnels in rock are planned and additional contracts will consist of 4 kilometers (2.5 miles) of twin tunnel, resulting in 8 additional linear kilometers (5 miles) of single track tunnel contracts yet to be offered in soft ground. Three recent contracts in soft ground included the New Austrian Tunneling Method (NATM), along with conventional tunneling, as a bid option. Section E5a, Fort Totten Station and Tunnels, was the only one of the three to be constructed using the NATM option. This is the first application of the New Austrian Tunneling Method in soft ground in the United States. This paper will concentrate on the Fort Totten Station chamber NATM design, construction, and the instrumentation readings and evaluations which lead to an engineering back analysis which allowed a refinement of the bid design, resulting in a faster, more efficient construction. Design of the Fort Totten Station and Lines was done by Sheladia Associates. The design team included Greiner Engineering and Jenny Engineering with Mayreder-Consult of Austria, who was responsible for NATM design and NATM construction consultation.

Jan 1, 1991

By Carl-Eric Dr. Nilsson

Energy cost for mine ventilation in Sweden is high, especially during winter time when air must be heated. This paper presents the result from a project entitled ventilation-as-required. The term ventilation-as-required means that the required volume of fresh air should be distributed only to such areas, where mining work is going on and to be reduced to a minimum in the rest of the mine. Ventilation-as-required is a monitoring system that controls the operation and capacity of the fans and measure the air pollutant gases, i.e. carbon monoxide, nitrogen and sulphur dioxide at strategic points. It is an active system that responds when equipment is under operation. MITU proposed in 1991 a project to develop a ventiation-as¬required system and such components as transmitters and receivers for the communication between the equipment and the fans. The mining companies, Boliden Mineral AB, LKAB, Outokumpu and Ammeberg Mining Corporation joined the project and have financed a joint research and development programme supported with a grant from the Swedish Government through NUTEK. MITU proposed a second project in 1992 to the mining companies to develop an improved "intelligent" fan for scope ventilation. Boliden Mineral and LKAB joined the project and have financed a joint research and development project supported by the Swedish Government through NUTEK. The Government even made a commitment to support the investment of the first 50 fans ordered with a grant of 25% of the investment cost. The result from projects show that the target set up in the plans is more than achieved, with an energy reduction that exceeds 30% compared to previous consumption. No environmental influence due to reduced ventilation is observed in the stope when work is under progress. Dilution of exhaust gases from diesel fuel decreased from 6.000 m3/L consumed diesel fuels to 3,600 m3/L. The automatic data processing and sensor system is even increasing the security of the work so that it can be done under safer environmental conditions.

Jan 1, 1995

By J. Villeneuve, G. Fourniguet

Simulation of Mineral Processes is now commonly used by the Engineers in charge of plant design or optimization but a good knowledge of the simulation tool is still needed to conduct a project. A new level of algorithm has been defined above the simulator to answer directly to the user's questions. This level has been called the supervisor of simulation, which is using the automation concepts of sensors and actuators. At any place of the flowsheet (i.e., a stream or an equipment), the user may indicate which value could change by graphically implementing an actuator. Then, he can evaluate the effect of the variation of this value at any other place of the flowsheet by inserting a sensor. Thus, by example, it becomes possible to look at the evolution of the recoveries and/or the circulating loads when scanning an interval of the possible teed flowrates. This approach conducts to an increased facility in using a simulator and in analyzing the predictions. It is also a very valuable tool for permitting to characterize the sensibility of the simulation results to the variation of some settings (e.g., load of grinding media, rotation speed, water addition, etc.) or feed characteristics (e.g., flowrate, sizes, grades, grindability, etc.). Thus, the most important variables can be identified for design and pre-control optimization of plants. This new level of simulation will be implemented in a further version of the USIM PAC simulator and selected examples are presented.

Jan 1, 1995

By George J. Dvorznak, Robert W. Waytulonis

The Bureau of Mines is conducting a research project in cooperation with the Mine Safety and Health Administration (MSHA). Mining companies, and equipment manufacturers are also participating through the Colorado Mining Association (CMA). The objectives of this cooperative research project are to determine the practicality of coupling a dry exhaust conditioning system (dry system) and diesel particulate filter (DPF) to make an integrated control system, and to determine the effectiveness and durability of the integrated system in an underground coal mine. Diesel-powered mining machines must be equipped with control devices to reduce surface and exhaust temperatures to safe levels and prevent flames and sparks from being emitted to the mine atmosphere. Diesel exhaust-gas water scrubbers have been successfully used for many years but they have several disadvantages; they are large, consume large quantities of water, and require frequent maintenance to remain functional. Additionally, diesel exhaust is a source of noxious gases and particulate matter. Particulate emissions are composed primarily of small carbon particles with absorbed hydrocarbons and they are almost entirely respirable in size. Even an engine in good mechanical condition can emit up to 400 mg/cu m of respirable particulate matter. A dry system for control of diesel fire and explosion hazards, coupled to a DPF, promises to be a complete control system for diesel engines. The dry system cools the exhaust and suppresses sparks and flame with a heat exchanger and flame and spark traps. The conditioner is smaller, consumes no water, and requires less maintenance than a comparable water scrubber. The DPF uses a ceramic substrate as a wall-flow filter and is very efficient at collecting exhaust particles. Average particulate mass collection efficiency is 90%. This report describes a cooperative research project to combine the dry system with the DPF, conduct performance tests on the integrated system at Bureau and MSHA 1aboratory facilities, and conduct field tests of the system on a production machine in an underground coal mine.

Jan 1, 1987

By E. (Walt) van Walsum

The MPTM was first applied in the U.S.A. in 1950 as described by Lewis, W.E., 1951. The method was then abandoned in the USA and rediscovered some 20 years later in France where it was greatly improved and widened in its scope of application. It was subsequently successfully introduced to Italy and Spain. The technique, at its present stage of development, provides solutions to tunneling in soil and in the softer rock types, which often were troublesome geological environments for tunneling. When used in conjunction with drilling-and-blasting, over break, excessive vibration, noise and fissuring of the rock can all be avoided. When used as an alternative to the New Austrian Tunneling Method (NATM), the MPTM provides safe, full face tunneling in stead of multiple headings, excavated sequentially; in addition, surface settlement can be virtually eliminated. When used as an alternative to a TBM, the method's flexibility and low capital cost make it attractive. This attractiveness is enhanced when ground conditions are erratic or when the length of tunnel to be excavated is limited. The method holds promise for tunnels of large cross section, to be excavated in soft ground or rock with unconfined compressive strengths of less than 80 MPa (11 600 psi). While in itself not new, recognition and development of the method's potential are. Further development work, aimed at increasing the range over which the MPTM can be applied, is in progress.

Jan 1, 1993

By Bilgehan Kekec, Sertac Dündar, Niyazi Bilim

"Knowledge of the abrasion resistance of aggregates is important when using them for asphalt and concrete mixes and highway construction materials. In this study, the usability of natural building stone waste as aggregates for different engineering applications was investigated. To this end, test samples were obtained from a number of natural stone quarries and stone cutting factories. The abrasion tests were carried out on the test samples and results were compared between samples. The abrasion strength values were determined with both the Micro-Deval (MDe) and the Los Angeles (LA) abrasion test methods. A correlation coefficient was also determined between the LA and MDe tests results using an appropriate statistical model.Introduction The rapid consumption of natural resources has led researchers to work on the efficient utilization of such resources. To this end one can convert waste into useful raw materials, or determine alternative uses of the industrial waste materials. This has become increasingly important as storing or dumping waste may result in environmental problems. In addition, the use of industrial waste in a different application of the construction industry prevents rapid consumption of limited natural resources and can mitigate environmental problems related to raw material production, Industrial waste such as blast furnace slag, fly ash, building demolition material, marble waste and dismantled asphalt have been used as highway and concrete materials (Ahmed 1993, Ramaswamy and Aziz 1992, Schroeder 1994, Ceylan and Manca 2013, Holtz and Eighmy 2000, Hebhoub et al 2011). It is very important to analyze whether these aggregates are of the required quality in terms of their application and their economic life. This analysis can be carried out using various tests such as the Micro-Deval and the Los Angeles abrasion tests, sieve analysis, durability chemical resistance, peeling and adhesion, and freezing-thawing tests (Erdem et al 1996). Specifications for aggregates also include terms that define the grain shape, cleanliness and surface textures."

Jan 1, 2017

By Merline W. Van Dyke

The Surface Mining and Reclamation Act of 1977, PL 95-87 (The Act) granted the Office of Surface Mining (OSM) the duty of collecting fees from the active coal mining activities to be used in abating the hazards associated with abandoned coal mines. Since the passage of the Act, OSM has been instrumental in closing a multiple of mine hazards and in full cooperation with the states involved. Complete mine closures range from simply filling a subsidence hole to exodic designs costing thousands of dollars, such as in the case of the Portal Park swimming pool in Colorado Springs, Colorado. The Portal Park olympic sized swimming pool was built over an abandoned coal mine by a group of local citizens and given to the city of Colorado Springs. This pool receives the largest number of users each year. During the past four years, OSM has abated six mine related hazards in and around the pool. During the summer of 1982, the pool started tipping causing the pool waters to run out the west end. This pool tipping and the associated cave-in problems caused great concern to the city and the local users. This citizens concern generated a request from the city for OSM to assist in checking out the pool problems. Early in 1983, OSM initiated a driling program to investigate the subsurface voids. This drilling effort revealed several large voids within a few feet of the pool deck, with all voids inundated with ground water. Therefore, the void filling method favored the hydraulic backfilling needed to be confined to the area under the pool. This confining problem lead to the development of the gravel bulkhead cutoff walls to confine the backfilling effort to the areas under the swimming pool.

Jan 1, 1985

By R. C. Klimpel

Size reduction of material in aqueous pulps by the use of tumbling media overflow discharge mills is an important and common unit operation in industry. There also has been extensive attention given in recent decades on developing a more fundamental understanding of the breakage processes involved, especially in ball mills. These studies have mostly emphasized the use of size-mass balance or population balance approaches for quantifying the analysis and design of size reduction circuits, ego Austin, et al (1984).

Jan 1, 1989

By Kevin Lundberg, Philip Sander, Daniel Weinberger, John Reilly

Since the early days of risk management, developments in technology and guidelines (ITA, ITIG, OGG, UCA) have advanced risk management and probable cost estimating, which are now widely recognized. WSDOT’s CEVP risk-based cost validation process is now established after 20 years. This paper traces these developments, summarizes advanced techniques, and presents examples of US and international projects with results. A particular case of using advanced risk evaluation to allow enhanced-capability TBMs to be considered in a competitive bid process is presented. Further advances, including the use of digital twin risk-based representation of complex projects, are described.

Jun 13, 2023