Search Documents

By R. J. Sweigard

Stabilization of slopes on abandoned mine land (AML) invariably involves some channelization to control surface drainage. Typically, these channels are lined with riprap or gabions, depending on gradient and expected flow rate. The conventional treatments pose a problem since they require frequent maintenance and replacement at times. Soil bioengineering presents an alternative to the conventional measures. In soil bioengineering, living woody plant material forms the main structural component in systems designed to prevent shallow mass slope failures, surface erosion, and channel bank erosion. An experimental application of soil bioengineering techniques was designed and implemented at an AML site in eastern Kentucky. The design consisted of live fascines and live stakes using willow branches installed with coir geotextile. Channel gradient, length, and cross-section were considered in the design.

Jan 1, 1998

By Steven W. Hunt, Steven B. Fradkin, Roger J. Maurer

During the 1980s and 1990s, twenty deep shafts were constructed in Milwaukee to depths from 85 to 91 m (280 to 300 feet) through soil and weak rock thicknesses ranging from 37 to 69 m (122 to 227 ft). Adjacent compressible soils, settlement sensitive structures and high groundwater levels required that shafts be constructed without dewatering. Contractors attempted several methods of ground support and groundwater cutoff. Significant problems developed during construction of 11 of the 20shafts. One shaft collapsed; groundwater blow-ins occurred at five of the shafts; and seepage caused unfrozen windows at three of the freezewalls. Ultimately, combinations of grouting and ground freezing were utilized to complete all of the shafts into bedrock. This paper discusses the main design and construction challenges experienced and the lessons learned.

Jan 1, 2003

By G. Camposano, J. Aponte, B. A. Ferguson

The paper covers mining operations and preparation of the ore prior to metallurgical treatment in the Process Plant. Mining operations are primarily concerned with the delivery to Ore Preparation of a balanced ore feed within fairly rigid specifications as to both ore type and chemical analysis. The mining method, systems of geological and engineering control, and the equipment employed are therefore reviewed in this context. In Part One of the paper the physical and geological characteristics of the orebodies, including the varied nature of the ore itself, are first described. Orebody evaluation, the calculation and classification of ore reserves, mining planning and forecasting to ensure continuity of production are covered, and the particular problems presented by sampling, the erratic distribution of ore values and the variation in the density of the ores are also mentioned. Mine design and ore excavation practice are described, together with the way in which they have evolved with recent developments in modern mining equipment. In Part Two of the paper, a detailed description of the Ore Preparation plant is given, centred around the concept of rubbling as a means of separation of the barren hard boulders from soft lateritic ore. Ore blending and ore reclamation operations are explained followed by a detailed description of the drying and crushing plant. The importance of the control of moisture content and ore sizing in the feed to the metallurgical plant is emphasized.

Jan 1, 1979

By A. T. Visser

The expansion of surface mining has led to the development of very large off-highway trucks capable of hauling payloads in excess of 290 t (320 st). Mine haul roads have historically been designed empirically, relying heavily on local experience; the trend in increasing truck size will thus render the current pavement systems inadequate. Because truck haulage costs can account for 10% to 50% of the total costs incurred by a surface mine, not only would the maintenance costs of existing roads of inadequate design increase, but vehicle operating and maintenance costs would increase prohibitively. Thus, there is a need for improved design technologies encompassing the construction and management techniques of mine haul roads appropriate for the wheel loads of vehicles now in use. This paper presents the different components of a mine haul road design and management system and demonstrates the value of its application through case studies. The system has been applied at several South African surface mines, and distinct benefits have been derived. The improved structural design of a new road resulted in a 29% saving in construction costs and provided better service, while the optimal selection and management of wearing course materials provided better functionality at lower total transportation operating costs.

Jan 1, 2000

By David S. Bolin, Gary R. Peterson

INTRODUCTION In both the United States and Canada, a company making a public offering of securities must comply with regulations which have been promulgated by Federal and/or Provincial Legislatures. This paper focuses on the regulations pertaining to reserve reports required by the United States Securities and Exchange Commission (SEC). SEC RESERVE FILINGS Reserve reports made to the United States Securities and Exchange Commission are the only reserve reports which are directly regulated by the United States government. The requirements for SEC reserve reports are set forth in the filing forms as shown in Appendix A, from Item 17A of SEC Form S-18. These reporting requirements, which are intended to protect the investing public from inaccurate or misleading claims, are primarily oriented to S-1 or other filings for new stock issues but must also be followed for annual 10K reports which must be filed annually by U.S. public corporations as part of the Corporate Annual Report. These undertakings require independent audits of reserves, mine designs, plant facilities and a general economic evaluation of the planned or existing operation as part of the backup documents for filing. An ore reserve is defined by the SEC as "That part of a mineral deposit which could be economically and legally extracted or produced at the time of the reserve determination". This definition is unchanged since it was last

Jan 1, 1988

By E. Scott Bair

Renewed interest in the vast reserves of anthracite coal in eastern Pennsylvania led to the use of a numerical model for simulating the hydrologic effects of constructing an open-pit anthracite mine. The proposed mine would be approximately 1800-m (5900-ft) long, 1000-m (3300-ft) wide, and 300-m (1000-ft) deep. A two-dimensional, finite-difference, ground-water flow model was used to calculate ground-water seepage rates into the proposed mine, to evaluate the effectiveness of various deep-well dewatering systems, to calculate drawdown in adjacent wells and properties, and to estimate the capacity of the water-treatment plant. Site-specific values of pertinent hydrogeologic parameters were used in the simulations.

Jan 1, 1980

By H. Reginald Hardy, Xiaoqing Sun

Rheological models are widely accepted as a means of describing the mechanical behavior of geologic materials. It has been found, however, that rheological models developed for a specific stress level on the basis of linear visco-elasticity generally are not satisfactory at other stress levels. It has been suggested that the parameters of such models should be functions of stress level (Hardy, 1965; Kim, 1971). In this paper, continuous functions of stress have been utilized to obtain the required variation of Burgers model parameters with stress level. The model developed using these functions provides a constitutive relation which reflects the real time-dependent behavior of rock materials. The new model is capable of predicting the creep behavior over a wide range of stress levels and also predicts mechanical behavior under different loading condition (e.g. constant stress rate). It is also interesting to note that the mechanical behavior of individual elements in the model appear to reflect the different stages of brittle fracture in rocks (Bieniawski, 1967), namely; crack closure, elastic deformation, stable fracture propagation and unstable fracture propagation.

Jan 1, 1986

By Igor V. Nazarov

INTRODUCTION Tens of deposits in' coal basins of Western and Eastern Siberia are being open-mined with the technology of overburden rehandling into the mined out space of pits by excavators - draglines. This technology is preferred due to the high productive Russian equipment, comparatively low cost, and relatively small Influence exerted on the environment. The basic tendency of the last decades is the aspiration for enlarging the sphere of the' technology application for development of gentle and steeply dipping seams with the use of blast destruction of overburden and with combined winning of loose alluviums and rock partings. Complex technological schemes with multiple rehandling are widely used. In addition to it, stripping workings, intermediate storage of mineral resources, placing of transport dumps, and engineering construction can be realized with the use of draglines. More than ten of dragline faces are simultaneously exploited in some pits, and the rehandling coefficient ranks from 0.1 to 8. Here, conditions of winning and placing (position of a face and existing dump) are varying in space and time; this leads to the necessity of reconsidering the order for conduction of works (schemes) within the current designing. By now, in order to this, it is required to realize complex engineering calculations by graph-analytical methods and definite experience. The need is available for automatization of this process by creation of the corresponding software. The software is to: • Orient on the active pits and use information on the existing geology, equipment, and situation in mine. • Calculate the existing schemes more operative and on a higher qualitative level to model their development in a pit space with parameter optimization. • Predict situations demanding to change the existing technology for mining operations and recommend optimal technological schemes. METHODOLOGICAL FOUNDATIONS FOR MODELING The problem is not new, it has more than fifty year-old history of creating mathematical models algorithms, and programs in Russia, Ukraine, USA, Canada. Australia and other countries with the developed mining branch. Conventionally, all population of programs can be divided into three groups depending on goal and interval of prediction: • Long-term programs used in designing and intended for substantiation of the nine capacity, selection of mining system, establishment of limits for applying the technology of overburden rehandling. Mid-term programs used in current planning for calculation of technological schemes and certificates of face in active mines.INTRODUCTION Tens of deposits in' coal basins of Western and Eastern Siberia are being open-mined with the technology of overburden rehandling into the mined out space of pits by excavators - draglines. This technology is preferred due to the high productive Russian equipment, comparatively low cost, and relatively small Influence exerted on the environment. The basic tendency of the last decades is the aspiration for enlarging the sphere of the' technology application for development of gentle and steeply dipping seams with the use of blast destruction of overburden and with combined winning of loose alluviums and rock partings. Complex technological schemes with multiple rehandling are widely used. In addition to it, stripping workings, intermediate storage of mineral resources, placing of transport dumps, and engineering construction can be realized with the use of draglines. More than ten of dragline faces are simultaneously exploited in some pits, and the rehandling coefficient ranks from 0.1 to 8. Here, conditions of winning and placing (position of a face and existing dump) are varying in space and time; this leads to the necessity of reconsidering the order for conduction of works (schemes) within the current designing. By now, in order to this, it is required to realize complex engineering calculations by graph-analytical methods and definite experience. The need is available for automatization of this process by creation of the corresponding software. The software is to: • Orient on the active pits and use information on the existing geology, equipment, and situation in mine. • Calculate the existing schemes more operative and on a higher qualitative level to model their development in a pit space with parameter optimization. • Predict situations demanding to change the existing technology for mining operations and recommend optimal technological schemes. METHODOLOGICAL FOUNDATIONS FOR MODELING The problem is not new, it has more than fifty year-old history of creating mathematical models algorithms, and programs in Russia, Ukraine, USA, Canada. Australia and other countries with the developed mining branch. Conventionally, all population of programs can be divided into three groups depending on goal and interval of prediction: • Long-term programs used in designing and intended for substantiation of the nine capacity, selection of mining system, establishment of limits for applying the technology of overburden rehandling. • Mid-term programs used in current planning for calculation of technological schemes and certificates of face in active mines.

Jan 1, 2002

By Y. C. Kim

M.S. Azun The article unfortunately has some serious flaws negating the usefulness of the paper. The authors claim that kriging (linear kriging) is superior to other methods such as polygon. This is not the case. The deterministic methods (referring to polygon, ID, IDS, etc.) should not be compared with the statistical methods (linear kriging, disjunctive kriging, etc.) because they differ not only in their assumptions, but also their tools used in estimation. Thus, they give different results. By comparing the results of deterministic methods and linear kriging, the authors conclude that polygon, IDS, and linear kriging give an average thickness close to the value obtained from realizations. Besides, they argue that linear kriging gives less variance than the others (Fig. 2). The first conclusion is expected, due to the well-known central limit theorem. The second is the result of the statistical properties of different estimators. Thus, the comparison presented in the paper is rather meaningless because the authors have failed to follow basic statistical procedures. The numerical results of different approaches to an estimation problem cannot be generalized. In conclusion, the paper is not a meaningful contribution, and sadly, quite erroneous. Reply by E.Y. Baafi and Y.C. Kim The two key contentions made by M.S. Azun regarding the paper are: deterministic methods should not be compared with statistical methods and, hence, the results are erroneous; and the paper does not make a meaningful contribution. The first contention is an academic one. Most practitioners in ore reserve estimation could care less whether the tool they are using falls under a deterministic or a probabilistic method, so long as it gives the desired answers. It is probably for this reason that, whenever any new tool such as linear kriging is introduced to practioners in the mining industry, they would like to see a comparison test performed between the existing and the more familiar tools with a new and "strange" tool. Only when a new tool passes such a test, the generally conservative mining community would begin to utilize the new tool to its advantage. The second contention, is a subjective one. The final judgment should be left up to the readers within the mining community. If kriging is accepted more among practitioners, partly due to the paper, then the paper makes a practical contribution to the state-of-the art in ore reserve estimation. Finally, M.S. Azun entirely missed two main points in the paper. The first is that any comparative study of kriging vs. Polygonal or IDS should be performed for local estimation and not for global estimation. In the past, kriging was frequently compared with other existing tools in its performance on global estimation. Such results were nearly identical due to the central limit theorem effect, which further prevented the acceptance of kriging by practitioners. The second point is that a single case study using an existing property, as it was frequently performed in the past, is not sufficient because results depend not only on the tool itself, but also on the nature of the mineralization.

Jan 3, 1984

By F. F. Aplan

Mineral process engineering is a small but important part of the nation's raw material industry. Minerals are usually processed in large plants of high capacity, at low cost, using few engineers and operators, and at an ever-increasing level of plant sophistication. The magnitude of the mining industry is huge, with about 4 Gt (4.5 billion st) of ore, coal and industrial minerals mined annually in the United States. Industries such as construction, manufacturing and power generation rely heavily on a strong US resource base to maintain a competitive edge. Though rooted in classical chemistry, geology, physics and mathematics, a mineral process engineer must be trained in the science and engineering required to process raw materials. A modern mineral processing program still stresses the traditional aspects of the profession. But it also emphasizes particle technology, applied surface chemistry, chemical processing of ores, solid-fluid separations, process and equipment modeling and optimization, materials handling, personnel management, maintenance and environmental and health aspects. In such areas as particle technology and some aspects of applied surface chemistry, mineral processing academic programs have taken a leadership position in supplying specialists to a variety of other industries. The objectives of a mineral processing program are: • to furnish personnel to support the basic raw materials industries (undergraduate programs); • to provide a research and development base for industry (graduate programs); and • to provide expertise in particle technology, applied surface chemistry and environmental programs for other industries (undergraduate and graduate programs). In the United States, mineral process engineering programs have historically been associated with mining and metallurgy departments. The recent movement of metallurgy programs away from primary processing towards materials science has created the need for a new accommodation.

Jan 1, 1992

By C. Zhou, B. Whisner, J. Carr

Proximity Detection Systems (PDSs) are used in the mining industry for protecting mine workers from striking, pinning, and crushing injuries when they work in close proximity to heavy machines such as continuous mining machines (CMMs). Currently all Mine Safety and Health Administration (MSHA) approved PDSs are magnetic field based systems which can be influenced by the presence of wire mesh that is commonly used for supporting roof and ribs in underground coal m ines. In this paper, researchers at the National Institute for Occupational Safety and Health (NIOSH) characterize the influence of the mesh on the performance of magnetic PDSs by measuring the magnetic field difference around a CMM caused by the presence of the mesh. The results show that the magnetic fields are generally enhanced by the mesh which causes the PDS detection zones to be increased correspondingly. It was discovered that the fields around the joints of two mesh sections have the greatest enhancement and thus deserve more attention. In addition, it is found that the presence of mesh can also cause a variation in the generator current. The influence of mesh is characterized by the change in the generator current with respect to the distance between the generator and the mesh. It was found that the generator current change caused by the mesh can be significant (on the order of ten) when the mesh is extremely close to the generator (e.g, less than 1 cm) and is negligible when mesh is relatively far (greater than 0.15 m). The findings in this paper can be used to develop guidelines and best practices to mitigate the influence of mesh on PDSs. INTRODUCTION The Mine Safety and Health Administration (MSHA) requires operators of underground coal mines to equip place-changing continuous mining machines (CMMs) with proximity detection systems (PDSs) to protect mine workers from striking, pinning and crushing injuries when they work around these heavy machines. Although a variety of technologies can be implemented for proximity detection, the magnetic-field-based PDS that was originally developed at the National Institute for Occupational Safety and Health (NIOSH) has shown great effectiveness in challenging mining environments and currently all MSHA-approved PDSs are magnetic-field-based systems. As shown in Figure 1, a magnetic PDS typically includes two major components----the magnetic field generator and the Miner Wearable Component (MWC). Magnetic fields are generated by injecting a high electric current into a ferrite-rod antenna sealed in the generator. The magnetic field strength detected by an MWC varies with the distance between the MWC and the generator. In a typical PDS, multiple generators are mounted on different locations of the machine. The relative location/zone of an MWC is determined based on the field strengths from different generators picked by the MWC. Ideally, for a PDS to work properly in the underground, the magnetic fields generated by the different generators should be stable and not vary with the environment, as the system would interpret any variation of the magnetic field as a result of the distance change between the machine and the miner wearing the MWC. In reality, however, this is not always the case since magnetic fields can be altered by a number of environmental factors such as the presence of steel wire mesh that has been widely used in underground coal mines for supporting roof and ribs In this paper, the influence of mesh on the PDS performance is investigated and the magnetic field change caused by the mesh is measured.

Jan 1, 2019

By M. Murillo, J. Botín

"Mining has always played a key role in the improvement of the quality of life, but also, it has been a source of environmental and social conflict. Despite the great progress in social responsibility and sustainability experienced in recent decades, the public image of mining remains low and mining projects and operations must face growing difficulties and demands, which results in increasing capital and operating costs. In practice, the objective of a mining company is to create value for its shareholders and therefore, the best approach to Sustainability would be to foster those drivers aligning sustainability and shareholders value, this is, the “Business Case for Sustainability” (BCS). Only under this assumption, convergence of corporate strategy and sustainability may be assured. This paper discusses partial results of a Research Project being carried out at the Catholic University of Chile, aiming to develop a social and economic model for the effective integration of the values of sustainable development in the strategy of mining companies and their stakeholders. INTRODUCTION Mining is fundamental for the wellbeing of our everyday life. But as important as these benefits are for humanity, the mining Industry has had negative environmental and social impacts. For these reasons, a closer relationship between “Sustainable Development and Mining” is more necessary than ever. The Brundtland definition of Sustainable development does not have a clear relationship with mining, but it provides the context. Under a strict interpretation of the Bruntlandt definition, stating that “Sustainable development is development that meets the needs of the present without compromising the ability of future generations to meet their own needs” [10], mining would not be sustainable because the minerals are non-renewable resources. However, this research focuses on how mining can contribute to the sustainable development in the territories where the projects take place. In other words, this research follows the publication titled “Berlin II Guidelines for Mining and Sustainable Development” [9], which stated that “A mining project that is developed, operated and closed in an environmentally and socially acceptable manner could contribute to sustainable development. Critical to this goal is ensuring that benefits of the project are employed to develop the region in a way that will survive long after the mine is closed”. The potential conflicts between mining stakeholders arises from the interpretation of the concept “developing, operating and closing a project in an environmentally and socially acceptable manner”, and the impact on the economic objectives of mining companies. Nevertheless, the ability of mining companies to control new demands and expectations of stakeholders has threatened the implementation and continuity of their projects and operations. To deal with these issues this research analyses the “Business Case for Sustainability” (BCS). It refers to the process leading to a business and social-economic environment whereby shareholders value may only be optimum under a business strategy which fully integrates the values of sustainability. In the model proposed, the Business Case will start when the benefits are higher than the costs. Benefits not only associated with efficient use of resources, also benefits associated with avoiding difficulties to continue with the mining projects such as strikes, heavy penalties, loss of investment, and so on."

Jan 1, 2016

By D. H. Dvorak

Two pilot-scale biological reactor systems were installed to treat metal-contaminated water. The reactors consisted of barrels and tanks filled with spent mushroom compost, within which bacterial sulfate reduction became established. Concentrations of Fe, Zn, Mn, Ni, and Cd were lowered by over 95% as these metals were precipitated as insoluble sulfides by reaction with bacterially generated H2S. The chemistry of the reactor systems is examined, and opportunities for maximizing their metal-retaining and alkalinity-generating potentials are discussed.

Jan 1, 1991

By Paul C. Miclea

With the growing urban population and the concern for traffic congestion and pollution (emissions control), public transportation is becoming more and more attractive to both city dwellers and managers. To gain access to the central area of the city, the sub- way remains the most viable alternative, despite its higher cost when compared to above ground or elevated transportation systems. There are relatively few regulations and criteria for subway ventilation, particularly when compared with mine ventilation. The main document that provides guidance and general recommendations for subway ventilation and environmental control is the Sub- way Environmental Design Handbook, published in 1976 (2nd edition) by the U.S. Department of Transportation, Office of Re- search and Development. Many of the subway systems in existence today have been designed and built with ventilation features adequate for normal train operation, but their design does not consider stringent criteria for such emergency conditions as a train fire in a tunnel. The National Fire Protection Association's Standard for Fixed Guideway Transit Systems known as NFPA 130 as well as the ASHRAE Handbook - HVAC Applications (1995) provide specific design and operation requirements for subway ventilation systems. Some of the existing, old subways are upgrading their ventilation systems to comply with the new regulations. The ability of a particular ventilation system design to provide adequate ventilation during normal and emergency conditions can be evaluated using computer modeling and simulation techniques. A train fire will cause a sudden change in the tunnel ventilation pattern by adding an unsteady and fast-growing source of heat. The hot air and gasses created by a fire will tend to flow uphill, possibly against the normal flow, producing a 'backlayering effect." To prevent this effect from happening, enough ventilation must be provided and the governing criterion to establish the required airflow is called 'Critical Velocity." Several software packages are available for special applications on tunnel and station ventilation as well as to model the spread of smoke and heat in case of a major tunnel fire, using Computational Fluid Dynamics. This paper presents the current issues in subway ventilation, as shared by the public transit community around the world, together with modern alternative design concepts vis-à-vis the more stringent emerging Fire-Life Safety criteria. Examples of recent studies and ventilation systems design are provided.

Jan 1, 1997

By A. Cordonnier, Ch. Obry, R. Evrard

In spite of the large annual expenditures and the vast field of activity covered, it cannot be said that many new grinding machines have actually come to light and modified the existing market for more than half a century. Manufacturers have mainly made advances in increasing machine sizes, efficiency and reliability, and in machine automation. The relatively recent emergence of roller presses is the only exception to this homogenisation of machine ranges. The development of roller presses in pregrinding has shown the advantages of compression grinding over the ball mill from the power consumption point of view. But classical roller presses still have maintenance problems due to the high grinding pressure. The FCB Research Centre has carried out much work in this field and in particular has studied the advantages of this process in pregrinding and integral grinding. These researches lead to the development of two new compression grinding machines. The first one, HOROMILL®, presented for the first time on the 8th European symposium on comminution at Stockholm, finds its application in the field of fine to very fine grinding in dry process. The second one, RHODAX®, presented at INTERMAT in Paris, covers the field of secondary and tertiary crushing and the first stage of grinding for most of the minerals in dry or wet process. Its high reduction factor permits to do with only one machine the work realised today with two or three crushing/milling stages. These two complementary machines offer a wide range of combination summarised on [Figure 1].

Jan 1, 1995

By X. Cheng

A series of batch flotation tests was performed on chalcopyrite-quartzite, pyrrhotite-quartzite, and on chalcopyrite-pyrrhotite-quartzite mixtures. Pulp potential measurements in the flotation tests of single sulfide minerals indicated that each sulfide mineral had its own optimum potential range for flotation. When these results were used to select the potential ranges for the separation of the two minerals from their mixture, their flotation responses changed and the selectivity of separation was adversely affected. A possible mechanism involving surface alteration through galvanic interaction is discussed. A method to improve the selectivity of flotation separation was proposed.

Jan 1, 1992

By Robert A. Westman

The INRED process has been developed step by step by Boliden since 1972 at MEFOS, the Foundation for Metallurgical Research, at Lulea in Sweden. The demonstration - plant is number five in this series. The purpose of this plant, which has a nominal capacity of 60,000 tonnes per year of hot metal is to: 1) prove the process on a sufficiently large scale to provide the basis for construction of production plants, 2) test various kinds of raw materials on behalf of licensees, 3) train operators of the first production plant, 4) develop the process further for special applications.

Jan 1, 1983

By A. W. Easton

INTRODUCTION This presentation will address changing trade patterns in lead and zinc from the mid 1980's to the early 1990's. Lead and zinc deposits are developed where they are found in many parts of the world. As many are not in major consuming areas, there is significant international trade in both lead and zinc concentrates and in refined metal. Forecasts of mine production have been analyzed, primary and secondary refining capacity and future consumption levels have been estimated, to arrive at the changes in trade patterns expected during the next half decade. This paper will first address concentrate and metal trade patterns for lead, then for zinc, and finally some remarks will be made on captive mine/smelter agreements, on regional trade agreements, and on barriers to trade. I would like to note that. there is only a small international trade in semi-fabricated products such as zinc die-cast alloy, zinc oxide, lead oxide or rolled lead and zinc. Most of the world's zinc and lead trade is in concentrates or refined metal. LEAD TRADE PATTERNS Lead Concentrates Six countries are exporters of lead concentrates. Three countries are in the Americas - Canada, Mexico and Peru, with two in Africa - Morocco and South Africa (including Namibia), and Australia. Due to the limited growth in lead consumption and consequent minimum investment in new production facilities expected, mine and metal production levels and future consumption levels are not forecast to change much between now and 1990. Accordingly, the tonnage of lead concentrates exported will remain essentially unchanged from these six countries. In total they have exports of 480,000 metric tonnes (metal content)* and by 1990 this figure is forecast to rise only slightly with the only increase taking place in Mexico. The concentrates are exported mainly to Western Europe & Japan. Apart from these six main lead concentrate exporting nations, a significant change is expected in the United States. In the mid * All concentrate trade figures are based on metal content

Jan 1, 1986

By M. Javier

Mining is most vital to our civilization. The current model of extraction technologies was designed without an expiration date and therefore generates environmental effects that are severe. Mining results-effects have been traditionally accepted and promoted around the world since Agricola described mining. Mining’s extractive technology is outmoded and standardized and inflicts negative results-effects on nature. Those results are liabilities dimensioned in legacy and type of nature able to provide to the next generation. In order to design, build, and transform mining effectively we must ask: What is the vision of mining? Mining has exhausted its antiquated mindset of over 200 years. Now it merely pilots us into crisis. The challenge today is to resolve the socio-environmental conflicts globally with a radical transformation of the mining business at its core. This paper illustrates that old mindsets must be radically updated or the concept of mining will continue to be trapped. Changing the mindset will enable discourse toward a new destiny. These changes will change mining for the better. We are able to evolve and get different results than in the past by pursuing a new legacy to live in harmony with nature for many more years. INTRODUCTION Minerals are supported by the law of conservation of mass. They have the unique characteristics of being finite, exhaustible, unsustainable, and have an unlimited recycling. Minerals are also hard to find because we have explored and virtually exhausted the whole crust of this planet. Orebodies that used to be considered world class are almost exhausted. In the short-term, it would be almost impossible to find new world class orebodies unless they could be extracted from the ocean, the moon or other planets like Mars. Mining is designed to extract minerals for profit and to keep civilizations functioning. Subsequently, mining has a social issue that is an economic issue. Thus, mining must be seen as a real and urgent subject matter that must be protected in thought and in fact. The actual mining extractive technologies produce disequilibrium in nature that has unknowable effects in the course of time. History is filled with the negative consequences to nature due to the model of mining. The evidence of these effects from mining’s model is apparent in repetitive liabilities around the world. The effects negatively impact nature without any consideration to how these impacts will manifest themselves in the future. This model of mining is widespread and extolled in every corner of the planet because it is old and familiar and although wasteful and outdated, we do not want to expend financial resources from profit or elsewhere to explore newer ideas, methods, or technologies that would help us keep a sustainable harmony between extraction and nature. We need a new vision for mining today and to explore in what way academia can and must play a social role in the teaching of mining methods. We need to question why we continue to support the old model of mining and to ask ourselves what prevents us from updating and modernizing the method of mining to meet the current needs not just of civilization but the urgent needs to undo some of the damage to the earth. This paper hopes to develop a method to change our minds about how we conduct the business of mining in order to control the destiny of it.

Jan 1, 2019

By Mark R. Bowie

Air-fall tuffs have been altered to zeolite via reaction of volcanic glass with local pore solutions at the six localities discussed in this paper. These are in the southern Basin and Range Province of Arizona and New Mexico, and in the Trans-Pecos and Coastal Plain regions of Texas. Zeolitization occurred in either closed- hydrologic, open-hydrologic, or hydrothermal groundwater systems. The tripping Spring Valley (DSV) chabazite in Arizona and the Buckhorn clinoptilolite in New Mexico originated in a late Cenozoic network of closed-hydrologic, lacustrine basins extending from southeast Arizona into southwest New Mexico. At DSV, two potentially commercial chabazite-rich tuffs are interbedded with lacustine mudstone. The main zeolite tuft contains up to 90 percent chabazite. The upper zeolite tuff averages approximately 67 precent chabazite. At the Buckhorn deposit, two clinoptilolite-rich tuffs are interbedded with lacustrine m udstone in the upper part of the Gila Conglomerate. The lower zeolite tuff contains up to 90 percent clinoptilolite. The upper zeolite tuff contains over 60 percent clinoptilolite. The Casa Piedra clinoptilolite is in the Trans-Pecos region of Texas. It formed during the Tertiary in a closed basin containing a playa lake. The Casa Piedra tuff averages about 60 percent clinoptilolite. Air-fall tuffs of the Cuchillo Negro, New Mexico and Tilden, Texas clinoptilolite deposits were zeolitically altered by either percolating ground waters in open-hydrologic systems or locally by ponded, saline, alkaline solutions. Cuchillo Negro tuffs are Tertiary and average approximately 50 percent clinoptilolite. Clinoptilolite-rich tuffs of Ebcene age have been mined from four quarries at the Tilden deposits. Tufts from the Kuykendall and Buck Martin quarries contain approximately 50 to 60 percent clinoptilolite. Low temperature, SiO2 - rich, hydrothermal solutions altered air-fall tuff to clinoptilolite and chabazite in the Foster Canyon area of the Tertiary Cedar Hills and Seldon Hills volcanic-vent zone in southcentral New Mexico. Poster Canyon tuffs contain up to 60 percent zeolite and average 40 to 50 percent clinoptilolite. The dominant mineral in the zeolite tufts at the six deposits studied is generally microcrystalline and either chabazite or clinoptilolite. Lithic fragments, unaltered volcanic glass, other zeolites, quartz, calcite, opal-CT, cristobalite, feldspar, evaporites, clays, and mafic minerals are also constituents of the tufts.

Jan 1, 1987