Search Documents

By S. B. Hildebrand

One of the highest costs associated with insitu leaching of copper is electric power. The ReGeneration Project addressed this cost issue with a research and development project for BHP Copper. The project involved the installation of a reverse pump/turbine for the removal of excessive fluid pressure and the production of useful electric power. The motivation for the project was that a reverse pump/turbine unit could not only remove the excess hydraulic pressure, but when connected to an induction .generator, would produce electric power, which could be easily connected to the local power gird, thus reducing operating costs. The project was successful in removing excess fluid pressure and producing electricity. The unit is operating today, producing useful 2,300 volt power at a rate of approximately 128 kilowatts.

Jan 1, 1998

By Martin N. Kelley

The Great Belt Link is a $3.5 billion fixed link across an 18 km (12 mile) wide body of water that separates the island of Zealand, on which Copenhagen is situated, and the main land mass of Denmark, Jutland, which is part of the European continent. The project consists of three main contracts. The first contract is an 8 km (5 mile) long, two-bore railway tunnel for the eastern half, the second contract is a 6.6 km (4 mile) combination railroad and highway bridge for the western half, and the third contract is a 6.7 km (4 mile) long high-level highway bridge for the eastern half. This paper will discuss the Eastern Railway Tunnel Project and the methods of construction that the joint venture consortium plans to use, along with its equipment selection. The ground conditions to be encountered begin with glacial tills, which are a mixture of clay, silt, sand, gravel, cobbles, and granitic boulders. The boulders can be up to 1-3 m (3-10 ft) in diameter. Underlying the till is a marl which is sometimes highly fractured with hydrostatic pressures of up to 8 bar. About 40% of the tunnel is in till and 40% in marl, with the remaining 20% being a mixed face of the two formations.

Jan 1, 1991

The purpose of the 3DOPT Program is to determine, starting from drill hole data, the optimum economic mining limits for an open pit. The economic limits are defined as those which maximize total profit, i. e. total mineral value mined less the total mining and milling costs, subject to the restriction imposed by the pit slopes. To accomplish this, the program employs the following: (1) A three dimensional matrix of equal sized blocks in order to file the engineering data and the cost/value data required to develop the profit figure for each block of ore/waste. (2) A graph algorithm developed specifically for optimizing these profits.1

Jan 1, 1966

By E. J. Owen, A. Appah, I. C. Sanchez, K. T. Stafford, N. Hurtig, R. Otoo, N. A. Iverson, S. A. Moses, V. T. McLemore

New Mexico lies at the eastern edge of one of the world’s great metal-bearing provinces hosting numerous Laramide and Paleogene mineral deposits. Southwestern New Mexico contains Laramide porphyry Cu (±Mo, Au) and Paleogene Mo-W deposits. Porphyry deposits are generally large, low-grade deposits containing Cu, Fe, Mo, Au sulfides (and other metal sulfides) associated with porphyritic intrusions and exhibit characteristic alteration styles. Porphyry deposits can also be spatially and temporally associated with skarn deposits and polymetallic veins. All of these deposits have the potential to host various critical minerals, including Cu, Zn, Bi, Co, Ni, rare earth elements (REE), Te, and W. Critical minerals may be found as substitutions within ore minerals or as separate mineral phases. These deposits are constrained using 40Ar/39Ar dating into three ore-producing magmatic pulses: 1) ~78–71 Ma Laramide pulse, 2) ~59–50 Ma, Laramide pulse, and 3) ~40–30 Ma Paleogene pulse. New and historic whole-rock geochemical data have highlighted areas with critical minerals potential that require further study.

Feb 1, 2025

By J. Pflieger

The International Iron and Steel Institute (IISI - http://www.worldsteel.org) has initiated the development of a comprehensive freely-available, internet-delivered package of highly interactive e-learning resources for undergraduate students and steel industry employees. The resulting e-learning environment (http://www.steeluniversity.org) creates a ?one-stop? shop covering all aspects of steelmaking, steel products and applications, the underlying scientific and engineering principles, industrial and academic collaboration, as well as environmental and sustainability issues relevant to the steel industry. The module entitled ?Sustainability, Steel and the Environment? of the steeluniversity.org provides interactive e-learning resources on the following topics - Sustainability. - Principles of Life Cycle Thinking. - Environmental Life Cycle Assessment. - Application of Life Cycle Assessment. The aim of this particular module is to enable the learner to identify relevant environmental parameters over the life cycle of steel products as well as to learn about the resulting environmental effects and impacts. Furthermore he/she will be enabled to explain the basic idea of Life Cycle Thinking and Life Cycle Assessment (LCA) in terms of Goal and Scope definition, System Modelling, Life Cycle Inventory (LCI), Life Cycle Impact Assessment (LCIA) and Interpretation. In addition, the learner can explore selected LCA scenarios facing the steel industry and its customers in the automotive and construction sectors.

Jan 1, 2007

By James J. Scott

Longwall mining has not received a great deal of attention in the United States; however, this system offers many advantages over the conventional room-and-pillar methods now being used. In order to conserve the coal resources of this country, the U. S. Bureau of Mines has investi¬gated the feasibility of adapting European longwall mining methods to American coal seams. Their studies showed longwall mining to be well suited to thinner seams and, greater depths; and, in addition, permitted almost 100 percent recovery of the coal. Most, experiments with this method resulted in higher overall production-costs than were commonly obtained with highly mechanized room-and-pillar techniques This high cost-was largely due to the excessive amount of labor required to maintain adequate roof support with conventional longwall mining techniques. With the substitution of hydraulic-powered, self-advancing roof support systems for conventional supports, this excessive labor cost has been decreased, and longwall mining costs are now competitive with those of modern room-and-pillar mining.

Jan 1, 1964

By Wayne F. Crockett, Martin H. Col

Gold, as a precious metal, has been sought for several thousand years. During this time economics have generally determined whether or not a deposit is minable. Today, few would spend $500.00 or $1,000.00 to produce one ounce of gold, yet most gold deposits currently being mined would have such costs if they were mined using the methods of the 18th century. Innovation has been the key to success in the world of mining. We are constantly having to look for new ways to mine deposits of lower grade, at greater depths, or with higher stripping ratios. The mining of placer gold deposits has always been subject to the volatile swings of the world price and the constant rise in production costs. The rise in costs is compounded by the drop in overall ore grades. Occasionally, a major technological innovation will dramatically reduce the costs of placer mining to allow previously marginal or unminable deposits to be mined at a profit. The continuous bucketline dredge was the last such major innovation in the gold placer mining. The continuous bucketline dredge has allowed large volumes of placer deposits to be picked up and processed on a continuous basis. Unfortunately, as the overall grade of the deposit declines, it becomes impossible to process enough ore to pay for the operating costs. There are many gold deposits around the world waiting for the next technological innovation that will allow them to be mined. One such deposit has been the Grey River deposit near Greymouth in New Zealand. The deposit contains gold reserves of 8992 kg, yet the deposit has been sitting idle for many years because the average value

Jan 1, 1988

By Jeffery Leavy, Ken Davis, Kirk H. McDaniel

The Waste Isolation Pilot Plant (WIPP) is a United States Department of Energy facility located in southeastern New Mexico. It is designed for the safe disposal of transuranic radioactive waste in deep geologic salt beds. Westinghouse TRU Solutions, LLC, the managing and operating contractor, undertook a project to simulate the processes at WIPP in order to identify bottlenecks and optimize available resources. The activities simulated in the model included the receipt, processing and disposal of radioactive waste underground, the mining of new areas for future waste disposal and the transportation of salt out of the mine. The complexity of the processes and the interactive requirements between processes required the use of advanced modeling techniques. The simulation model includes a huge number of locations and path network node points, with movement to and from the locations controlled using parameters rather than explicit routing. Information for the timing and sequence of the mining and nuclear waste emplacement operations is brought into the model via spreadsheets. Arrays in the simulation model keep track of past and future events that occur. Routing to the multiple possible positions in the underground mine is done using attributes, and system functions within ProModel in order to allow for a highly flexible sequence of planned events and to reduce the level of effort in creating the ProModel processing. Considerable use of subroutines in the simulation model is utilized for parametric decision-making that is repetitive. This presentation describes the modeling techniques used to accurately simulate the surface and underground operations. The surface and underground operations are considerably different, thus they will be treated in their own sections.

Jan 1, 2002

By Wilbur C. (Original by) Helt

Throughout the history of mankind, the principal use of coal has been to produce heat through combustion. The heat is used in many ways: to warm air space for our comfort; to provide heat or energy to power industrial processes, such as cement and steel production; and to produce electricity. Because it is our nation's most abundant fossil energy fuel, coal in the late 20th century is on the threshold of becoming a significant source for synthetic liquids and gas energy fuels for this country. This is made possible by conversion processes which can change solid coal into various synthetic gases and liquids. These coal-derived fuels are nearly identical to the processed fuels and chemicals provided by natural gas and crude oils, which presently provide almost all the petrochemical feedstocks and energy fuels needed for the residential, light commercial, and transportation markets. A revolution is beginning to take place, not only in the United States, but in many other countries with a return to a coal-based energy economy. Also, new combustion and conversion technologies which are compatible with national health and environmental goals are rapidly emerging. These technologies will allow coal's use to be expanded not only in its traditional markets, but also to supply markets held by natural gas and crude oil. With the worldwide decline in natural gas and crude oil reserves, coal is being-looked upon to meet the energy demand. Because of these new coal conversion technologies, coal will no longer be only a combustion fuel, but a valuable raw material for production of a variety of clean fuels and chemicals.

Jan 1, 1981

By Francesco Chiappalone, Daniele Nebbia, Lance Waddell, Greg Colzani

As part of the 3RPORT Project, a 5-mile tunnel is being excavated underneath the three rivers of Fort Wayne using a 19-foot diameter Slurry Tunnel Boring Machine. The groundwater pressure at the tunnel axis ranges from 4.5 to 5.3 bar. The rock mass hydraulic conductivity is very high with water inflows up to 10,000gpm imposing significant challenges to the project. After excavating 1,550-feet of the TBM tunnel, major leaks between the tailskin and the segmental lining were observed, indicating the potential deterioration of the tailskin brushes and the need for inspection and eventual replacement. The first part of the paper describes the planning of the intervention, including the design of the polyurethane grouting campaign, the procedures developed for the execution and the controls established during construction to timely assess the presence of potential hazards. The second part of the paper focuses on the experience gained during execution and lesson learned to prevent future occurrences of this nature.

Jun 13, 2021

By Dani Delaloye, Kas Zurek

Evaluating and selecting the appropriate excavation method is a key to the success of any tunnelling project. The benefits and risks of different methods should be well understood by the designer and communicated to the project owner to enable selection of a preferred method from a technical, social and environmental impact, cost and constructability perspective. For tunnels that have an internal diameter around 3 m, depending on the tunnel purpose and ground conditions, both microtunnelling with pipe jacking and tunnel boring machine excavation with a one- or two-pass lining may be feasible construction methods. Using the Ferry Road and Riverbend Combined Sewer Relief Project located in Winnipeg, MB as a case study, this paper will discuss the benefits and drawbacks of each method, including technical design, social, environmental, cost, schedule, and risk considerations.

Jun 13, 2023

By Frank Matter

Production of ultrafine powders of industrial minerals has been a problem in the past. In recent years new wet and dry grinding stirred ball mill systems have emerged which have been commercialized Two such systems are the TRZK mill with double step air classifier for dry grinding and the NRZK mill for wet grinding The primary features of these mills are feed entering from top and the product along with the grinding media leaving from the bottom, and a media separation and recycle system A detailed description of the NRZK mill for grinding coal is presented

Jan 1, 1983

By Rashi Tiwari, George Danko, Jeremy Knowles

A control technique is described for enhancing the efficiency of materials handling and other mining operations. The concept involves human-operator and robotics control interactions to assist in mining operations. Many mining tasks require a human operator to coordinate the motion of several machine links by simultaneously manipulating multiple joysticks or other control devices. The new control architecture allows for automatic coordination of multiple machine joints. The machine movement may follow a computer-optimized, learned coordination pattern, while the operator still retains the master control of the overall trajectory and velocity parameters. Examples are described for a surface mining front shovel.

Jan 1, 2005

By A. S. Astakhov

Working out of the production calendar plans (schedules) at deep mines which provide for the interaction of all kinds of mining operations determining coal output growth and mining and technical indices is a striking example of mining art. However, multi-variant decision making, a sophisticated system of integration, as well as high labour consumption for calculation and graphic operations in calendar planning require the improvement of traditional techniques and the development of new methods for calendar planning of mining operations at deep mines. The following specific aims were pursued in developing a computerized system of calendar planning (scheduling) of mining operations.

Jan 1, 1979

By J. R. Allan

Loki Gold Corporation of Vancouver, B.C. is developing the Brewery Creek Mine, an open pit heap leach gold mine, 55 km East of Dawson City in Yukon, Canada. Mineable reserves are 17.1 million tonnes of ore grading 1.45 grams/tonne, containing 24.8 tonnes (797 000 oz) of gold. Ore processing will employ a cyanide heap leach using run of mine ore. Permitting this mine has drawn significant attention because the heap leach technology, while proven in other jurisdictions, has not been used in Yukon. Engineering design of the heap leach was similar to that for heaps in more temperate climates, with the added issues of permafrost and cold weather operations. Solution balance with seasonal placement of ore and year -round leaching requires very large pond capacity for spring thaw conditions.

Jan 1, 1996

By Harold L. Kike

Until recently sulphur uses were so broadly based that economists used sulphur consumption to measure industrial activity. However, sulphur use patterns are changing and the manufacture of phosphate fertilizers presently accounts for approximately 65% of the world's sulphur consumption compared with only 25% in 1960. This has encouraged the development of new agricultural and industrial uses for sulphur. Major emphasis has been placed on its use as a fertilizer and in the manufacture of paving materials, specialty concretes and coatings. Some of these uses could have a significant impact on future sulphur usage.

Jan 1, 1986

By M. Scherbakov, W. Shi

Abrasion is an important mode of performance for any element of an engineered product that involves material contact for example, a conveyor belt cover. Abrasion resistance is considered to be one of the leading factors in belt cover design and improvement. Various types of abrasion testing are reviewed by and compared to actual belt applications. A new quantitative screening torsional abrasion test is developed by Goodyear to mimic a dynamic contact between belt cover and differently shaped stones of various weights dropped onto belt at any angle, velocity and height.

Jan 1, 2004

By Michael M. Carroll, Zhu-ping Duan, Han-ping Chin

INTRODUCTION The inelastic stress-strain behavior of rocks has urged engineers to seek for the possible application of plasticity to engineering pro¬jects such as tunnels, oil wells, dams, etc. for a long time. Early efforts in this direction have tentatively used the classical theories to solve some axisymmetric problems, in which the rocks were treated as perfectly plastic and nonfrictional materials (Talobre, J. A., 1957). Meanwhile, one of the fundamental assumptions is that the volume strain of elastoplastic material is purely elastic. Drucker and Prager (1952) developed a perfectly plastic and frictional model with a generalized form of Mohr-Coulomb law, which serves as both failure criterion and yield criterion. Although the associated flow rule gives unacceptably large dilatancy, this model is a very important step to deal with the frictional behavior of geological materials. As a further step, Roscoe et al (1963) and Schofield and Wroth (1968) proposed a Cam-clay model, which accounts for the yielding before the material reaches a failure envelope and reflects the plastic volume strain as a strain hardening factor, and the open end of the Drucker-Prager envelope is capped by a family of yield surfaces, the envelope is made conforming with crit¬ical void ratio line. The proposed shapes of the cap have been based on experimental data and on convenience of mathematical descrip¬tions. Drucker, Gibson and Henkel (1957) introduced a spherical cap for soils, while in Cam-clay model the cap is semi-logarithmic yield function derived from the result of triaxial tests. DiMaggio and Sandler (1971) proposed an elliptical model for sand, in which the hardening function depends exponentially on plastic strain. Sandler et al (1976) used a plane cap model to express the behavior of a wide range of geological materials of which the nonlinear hysteretic nature is significant. Mizuno and Chen (1982) illustrated the physical mean¬ing of cap models and their adaption to finite element calculation. In recent years, Carroll et al (1972, 1980) have studied the com¬paction of porous materials under hydrostatic pressure and discussed the mechanism of the nonlinear response thoroughly. Analytical and numerical analysis of the hollow sphere model by Curran and Carroll (1979) predicted an initial yielding surface, dependent on the initial porosity, and showed a strong coupling between hydrostatic and deviatoric effects. All these main features from the abovementioned theoretical research are visualized by the experimental data on Boise sandstone (1984). The combination of such previous work would be logically the construction of a plasticity model for porous rocks which, following the tradition of assigning the name of birthplace to a special model, is called Cal-Rock model (Carrol, M. M., 1984). The results of triaxial tests along different loading paths reveal the compaction characteristics for deviatoric and hydrostatic stress separately. the fitting of the nonlinear stress-strain curves leads to a construction of yield surfaces. Moreover, an uniaxial strain test gives the strength envelope which is the critical state line. The whole model is composed in the frame of elasticity theory. The concept and representation of plasticity used here are in the spirit of Naghdi¬Casey theory (Casey and Naghdi, 1984 and 1984, Naghdi and Trapp, 1975). In order to find the way of using such a plasticity model in engineering problems, the stress field in a thick-walled cylinder of porous material is calculated. This is an axisymmetrical problem with plane strain, which is an idealization of oil well in an infinite medium. Because the constitutive relation is highly nonlinear, a numerical method has been utilized to obtain the solution. CONSTRUCTION OF CAL-ROCK MODEL (1). Elastic-plastic constitutive equations The basic assumption is that the yield surface in stress space depends on one parameter, namely the plastic volume strain, as the data on Boise sandstone suggested. Starting from this point, the theory formulated in stress space and in strain space by Naghdi and his co-workers (1975, 1981) can be simplified. The simplified yield function is

Jan 1, 1986

Precious metals exploration is increasingly involved with concealed, deeper-seated gold-silver deposits which exhibit considerably more challenges to the geologist than near-surface, oxidized ores. Thus, cost-efficient, rapid and more detailed target selection and definition will be crucial for gold-silver exploration in the 1990s (Kral, 1990; Woodall, 1992). Although new developments in geophysical and geochemical exploration techniques have made significant contributions, the powerful capabilities offered by alteration mineralogy continue to remain untapped in many cases

Jan 1, 1993

By D. K. Sitler

Continuing advancements in manufactured diamond materials as used in rock cutting tools have created a new generation of high production tools for mining. This paper reviews the three major manufactured diamond product types available in the mining industry as supplied by General Electric Co., Specialty Materials Dept., and examines the ways these materials are used. As an integral part of this examination, the economic impact of manufactured diamond tools is evaluuted. Time and again, one will find that the premium price for these tools is economically justified when compared to traditional tools.

Jan 1, 1988