Search Documents

By A. Goulsbra, S. McAllister, R. Dunne

Since 1992, a tailings gravity re-treatment plant has been in operation at the New Celebration Gold Mine to recover aurifer­ous pyrite (Martins, Dunne and Gelfi 1991; Martins, Dunne and Delahey 1993). The gravity pyrite concentrate is ground in a Tower mill to liberate gold (average particle size around 25µm) prior to cyanide leaching. Although the re-treatment plant has met the predicted gold recovery, based on original laborat01y testwork, there is still room for improved gold recovery. This requires enhanced pyrite recovery, especially in the finer size ranges. The application of centrifugal gravity separators would seem to be an ideal means to achieve this criterion. In particular, the Falcon continuous centrifugal separator (Series C machines) would appear to be ideal for this particular duty. A testwork program to evaluate the application of the contin­uous Falcon to recover pyrite from New Celebration ores was unde1iaken over a six month period during the later part of 1997. The work involved laboratory batch testwork, followed by con­tinuous testing of the Falcon Cl0 (2tph to 3tph) and Falcon C40 (l00tph) units. A summary of the results from this evaluation program are provided in this paper.

Jan 1, 1998

By Graham E. Rawlings

Geotechnical investigations for underground projects are subject to a variety of constraints, including factors such as accessibility, geological complexity, thickness of oberburden and finance. As a result, the extent of geological data available for route selection and assessment of underground design and construction problems may vary between wide limits. It is essential that the data collected, the degree to which it is representative, and the confidence with which the problems can be anticipated, should be reflected in the type of contract set up and the way in which the contract documents are written. The paper addresses the methods by which investigations can be focussed to make suitable overall ground assessments for feasibility level studies. Subsequent investigations can then be objectively directed toward obtaining data on specific geotechnlcal problems or aspects which impact tunnel, cavern and shaft design and construction. The extent of investigations at the preliminary and design engineering stages must be closely related to the geotechnlcal surveillance and control during excavation. Fixed-price contracts necessitate a secure geotechnical data base prior to bidding, and the provision of that to the tenderers. By contrast, 'design-as-you-go' contracts minimize the geotechnical information needed before construction, yet require immediate assessment of the excavated ground for determination of support requirements and payment category.

Jan 1, 1983

By J. Loredo

Asturias, in northern Spain, emits 18 Mt CO2/year to the atmosphere, which supposes the biggest industrial CO2 emissions in the country. In order to avoid CO2 emissions to the atmosphere, keeping the availability of energy from fossil fuels, background studies focussed to the selection of favourable sites for CO2 geological storage are necessary. In Asturias, the options for CO2 geological storage are sequestration in deep saline aquifers or sequestration in unexploted coal beds. In the area, there is the biggest coal basin of the country and a great Palaeozoic sedimentary basin with appropriate silicoclastic or carbonated reservoirs and impermeable caprock for CO2 geological storage, located in proximity to thermoelectric power plants and other sources of CO2 emissions. All evidences suggest that CO2 storage in deep aquifers is the most interesting option but a legal planning and a technical regulation are still to be done. The possibility for CO2 sequestration in coal beds is modest and associated to the CBM commercial exploitation. It is necessary to have in mind that the feasibility of CO2 geological storage in Asturias apart of technical factors will depend on price of CO2 ton, legal conditioning and possibility to apply emission rights to projects.

Jan 1, 2006

Mineral sands mining for ilmenite, rutile, and zircon will disturb over 2,500 ha of prime agricultural farmland in Virginia and North Carolina (USA) over the next 20 years. Mining of the Virginia deposit was initiated in 1997 and approximately 750 ha have been disturbed to date with approximately 150 ha reclaimed to support a mix of agricultural post-mining land uses. While considerable university research and corporate effort were devoted to developing environmental management systems and reclamation protocols for these lands, specific indicators of sustainability and restoration success were lacking. By 2003, it became apparent to the mining operator (Iluka Resources), local land-owners/farmers, local government, and the regulatory authority that testable indicators of reclamation success were essential for long-term sustainability. Virginia Tech worked cooperatively with all stakeholders to review the pre-existing research base and to propose reasonable expectations of post-mining soil productivity levels. The state regulatory authority reinforced its position on a number of associated issues including necessity of topsoil return and specific comparative crop yield targets. Virginia Tech, Iluka Resources, and a local leaseholder (Carraway-Winn family) agreed to jointly manage a 45-ha research demonstration farm where the effects of alternative soil reconstruction practices are being rigorously monitored for both row crops (corn and wheat) and forage production. All mined land crop yields are also compared to an adjacent undisturbed exceptional quality prime farmland soil. Corn and wheat yields in 2005 and 2006 were significantly above county average yields (regulatory target level) and approximately 75% of undisturbed adjacent prime farmlands. This cooperative effort allows all clientele groups to objectively assess the post-mining productivity of these mined lands while providing an invaluable educational opportunity for the mining industry.

Jan 1, 2007

By Val Ness, Leonard Harris

Mentoring is defined as close counseling by an experienced and objective advisor within the industry. It is one aspect of attracting the best candidates into the minerals industry, holding their interest, and encouraging stable career growth. By encouraging proper mentoring practices, we foster strong careers, we transmit important wisdom to the next generation, we fortify the industry with better talent, and we encourage the best possible advocates for the minerals industry. This paper illustrates the consequences of poor mentoring, offers an example of positive mentoring practice at the college or university level, reviews some guidelines for stable and fruitful mentoring, and proposes a plan to spread appropriate mentoring practices. Authors' note: The use of masculine pronouns is for convenience and simplicity only. Our best engineers and managers come from both genders, and the authors intend no slight to either one.

Jan 1, 2001

Research has determined that ground control interaction problems in mining over a previously mined seam occur primarily in the tension zone created at the edge of the subsidence trough, and in areas above lower seam remnant pillars. Based on empirical and analytical studies, planning options for improving conditions on the upper seam have been developed to optimize extraction while minimizing the negative effects of seam interactions. These options include prediction of potential upper seam damage, guidelines for minimizing inevitable negative interaction effects, and recommended opening and pillar sizes, shape, and orientations, as well as design and planning procedures.

Jan 1, 1988

By R. Bhaskar, H. Xie

Fractal theory was horn in the mid-1970s. Since then, its application has been spreading day by day, from mathematics and geology to areas such as geophysics, physics and material sciences. In this paper, fractal models are developed to characterize particle size distribution and surface area. Theoretical formulas are derived for the computation of fractal dimensions D (size) and D[s] (surface area). The models developed are applied using experimental data of particle size distribution and surface area obtained from the Microtrac Particle Size Analyzer for dust processed by several size reduction devices. The theoretical models and the experimental data are found in good agreement. The fractal dimensions obtained are D = 1.350 to 1.770 and D[s] = 2.058 to 2.584 for fine coal dust particles (< 15 µm) produced by various size reduction mechanisms. The physical meaning of these fractal dimensions is also related to the dust generation processes.

Jan 1, 1994

By L. A. Taylor, R. O. Colson, D. S. McKay

The production of oxygen on the Moon utilizing indigenous materials will be essential for successful lunar colonization. Several processes have been put forth to accomplish Lunar Liquid Oxygen (LLOX) generation. The schemes that have received the most study to date involve: 1) Reduction of ilmenite (FeTi03) by H2, CO, CH4, CO-Cl2 and Cl2, plasma. 2) Molten silicate electrolysis, both unadulterated and fluoride fluxed. 3) Several others, including H, reduction of glass, carbo-chlorination, HF acid leaching, fluorine extraction, magma oxidation, and vapor pyrolysis. The H2 reduction of ilmenite and molten silicate electrolysis processes have received the most study to date. They are both feasible schemes and have various pros and cons, including their feedstock requirements. However, all processes should be addressed at the onset of LLOX research. This paper reviews several of the most studied and feasible processes for winning oxygen front lunar materials. There is an obvious need for more experimentation and study.

Jan 1, 1994

By Roy Eric Lurie

Computer based signal processing techniques for obtaining empirical dynamic models from measured mill circuit data are discussed. This modelling is the first step towards designing a particle size control strategy. Experimental data from a computerized acquisition sys tern is examined and analysed, and a number of model identification procedures are applied. The resulting models are compared and a suitable model is selected, illustrating the benefits of computer tools for control system design.

Jan 1, 1992

By Louis W. Cope

The Compañía El Zapote Yacimiento Y Minas, S.A. has an ore body containing 650,000 tons of 0.185 oz/t gold ore in Mexico. Metallurgical testwork has been done to determine the response of this ore to several possible processing schemes. The paper describes the rationale for selecting the Silver State Mining Co. methods in Colorado. Plans for developing the mine and building the treatment plant are described in detail in the paper. Estimates of capital and operating costs are included.

Jan 1, 1984

By W. Z. “Ben” Wu

The investigation provides a method of efficiency evaluation among several kinds of tools employed to cut different types of rocks. A ballistic test stand incorporated with a modified Hopkinson bar was used to simulate a percussive drilling tool. An Apple IIe microcomputer was employed for high speed data acquisition and numerical analysis. A newly developed method for remote monitoring the rock-tool interaction, including contact force, bit penetration and energy transmission,is presented in the paper. Theoretical predictions and experimental results appear in faily good agreement

Jan 1, 1986

By William J. Maloney

Blind drilled shafts are becoming increasingly popular as a secondary and sometimes primary means of ventilation. This is particularly true in the Appalachian coalfields. Some reasons for the rebirth of blind shafts are economics, timeliness, safety characteristics and their inherent independence from underground operations. Blind drilling has had limited use in hard rock and tunneling ventilation. Advances in cutters, bit design, equipment and lining systems have made blind drilled shafts the shaft construction technique of choice for ventilation specialists. History of blind drilling Blind drilling&apos;s roots include the Nevada test site, the coalfields of Appalachia and Germany, and the uranium mines of Arizona. Early technology was developed using a variety of equipment mainly of oilfield origin. Shafts completed by oilfield equipment ranged from the shallow 1.5 and 1.8 m (5 and 6 ft) lined shafts on the Nevada test site to two 3 m (10 ft) lined, 222 m (730 ft) deep shafts in Alberta for heavy oil development. Several of these shafts were completed to extraordinary depths. The record, completed in 1969, is a 2.28-m-diam (90-in.-diam), 1875-m (6150-ft) deep shaft, located in the Aleutian Islands of Alaska.

Jan 1, 1993

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

Hydrodynamic investigations in exploratory boreholes and grouting holes are conducted for the purpose of obtain¬ing information about the hydraulic properties of the hydrostratigraphic section to be intersected by the proposed underground workings. The information obtained from the investigations provides the basis for calculating the hydrau¬lic coefficients of fractured permeable rock, the dimensions of the anticipated grout isolation curtain(s) around the un¬derground workings, the number and location of grouting holes, the injection pressure modes, and also the volume(s) of grout that will be required (Anon., 1976, 1978). The following data on each aquifer are obtained from the investigations conducted in monitoring and grouting bore¬holes and the analysis of the results: 1) the top of each hydrostratigraphic unit, 2) the thickness of each unit, 3) the ground water fluid potential distribution in each unit, 4) the coefficient of permeability, 5) the piezoconductivity, 6) the fracture porosity, 7) the geometry of the fractures in the rock, 8) the elasticity-compressibility coefficient of the fractured rock, 9) the chemical composition of the ground water, 10) the direction of flow of the ground water, and 11) the expected inflow rate of water into the shaft, drift or tunnel. STG uses its DAU-3M type flowmeter to conduct in¬vestigations of directions of flow in vertical, inclined and horizontal drillholes. The DAU-6 instrument is used to de¬termine the direction of flow of ground water in each frac¬ture or fractured aquifer. Various singular and double DAU type packers are used for pumping and for injection studies (tests) and for flowmeter investigations. Normally the instruments enumerated above permit in¬vestigations to be conducted in each separate aquifer with¬out reinforcing the holes with casings. On the basis of these investigative data, both the hydraulic properties of unfractured rock and the hydraulic properties of the fractured rock are estimated. Dual porosity rocks require special attention because they tend to segregate the grout. 3.1 FLOWMETER INVESTIGATIONS IN BOREHOLES The STG flowmetric methodology is based on the mea¬surement of the ground water flow rate through the borehole by hydrostratigraphic interval after the disturbance of the hydrostatic equilibrium in the "hole-aquifer system" (after pumping or injecting). The relationship of the head changes to the discharge into or from a particular hydrostratigraphic unit obtained during the tests serve as the basis for calcu¬lating the hydraulic properties. Flowmetric investigations facilitate the determination of the number of aquifers, their depths, their thickness, the hydraulic properties of the fractured rock and the magnitude and direction of the flow of ground water. 3.1.1 FLOWMETER HARDWARE STG conducts flowmetric investigations in boreholes using its DAU-3M-108, DAU-3M-73, DAU-3M-57 and DAU-3M-44 instruments.&apos; They have respective external diameters of 108, 73, 57 and 44 mm. The type of flowmeter selected for use depends on the borehole geometry and the technological scheme for carrying out the investigations. Boreholes with a drilling diameter of 76-93 mm are inves¬tigated with the DAU-3M-73 flowmeter; boreholes drilled by bits with a diameter of 112 mm and more are investi¬gated using the DAU-3M-108 flowmeter. The DAU-3M¬108 and DAU-3M-57 instruments are used for flowmetric investigations with a packer. 3.1.1.1 The Downhole Sensor The sensor design of the DAU-3M-73 hole flowmeter is shown in Fig. 2. The design of the DAU-3M-108 instru¬ment is similar to the design of the DAU-3M-73 instrument. The frame of the flowmeter sensor shown in Fig. 2 consists of a casing, an upper and lower centering mount and two rings to which the guiding rods are attached. The upper rods are built into the connector bushing; the lower rods are built into the coupling sleeve. The borehole cable is attached using a half-coupling, a packing ring and a constriction nut. Thus, the frame of the flowmeter sensor is made so that the free passage of water to the impeller is facilitated along with the necessary rigidity. The primary moving component of the flowmeter is the double-bladed impeller, which rotates on cobalt-tungsten pivots and agate thrust bearings. Special extended air cham¬bers protect the supports of the impeller from the action of the borehole fluid which may contain fibrous and abrasive particles. The air located in the chambers shields the sup¬ports from direct contact with the borehole fluid when the sensor operates in a borehole. The hollow casing of the impeller serves the function of a lower cap. The upper cap is attached to the casing using a threaded connector; it is affixed also with a lock-nut. An adjusting screw with a

Jan 1, 1993

By Michael S. Robinson, Serge Moalli

Construction of the CSO Retention - Treatment Tunnel, Segment 1 in Dearborn, Michigan includes excavation for an overflow Structure with a minimum inside diameter of 15.24 m (finished). The excavation extends downward through overburden soil including a 15.2 m thick zone of potentially weak clay. This paper presents the subsurface data for the clay and a geotechnical analysis thereof, together with predictions of the behavior of the planned 15.54 m inside diameter open end caisson as it is sunk through this potentially weak zone. In a companion paper, the writers will compare the behavior observed with that predicted.

Jan 1, 1995

By P. E. Sperry, J. M. Duncan

INTRODUCTION The purpose of the report on which this paper is based is (1) to evaluate the potential for cost reduction of urban mass transit tunnels by use of alternative materials transport systems during the tunneling process, and (2) to identify research and development program elements to assure that the materials transport system will not become the limiting factor for the rate of excavation. The approach taken was: Review the state of the art of urban tunneling by extensive interviews with representatives of tunnel contractors, equipment manufacturers, government agencies and consultants, and by review of recent literature.

Jan 1, 1979

By M. C. Rockwell, G. F. T. Lay

Promising placer gold exploration sites offshore Lunenburg County are drowned pre- and post-glacial river channels and auriferous glacial tills. Gold values up to 5.67 9/m3 have been encountered in the vicinity of the Ovens Peninsula offshore Lunenburg County. Moderate gold values associated with notable amounts of heavy minerals were reported from various other exploration sites in this area. This paper highlights the major geological and gemorphological features for placer gold depositions in southern Nova Scotia. The past to present gold exploration activities nearshore and offshore Lunenburg County are summarized and potential areas for placer gold identified.

Jan 1, 1988

By C. Widham

Introduction It is generally accepted as dogma that sampling contributes most of the error in gold fire assays. Differences in assay results on pulps from the same sample interval are frequently regarded as evidence of the presence of the so called "nugget effect" of relatively coarse gold particles. It is true that coarse gold particles can contribute to substantial sampling fluctuations. But, while the process of sampling is probably the major source of error, the analytical process cannot be completely ignored as a possible contributor to erratic assay results. To maintain a stable assay process, the analytic part of the system must also be kept in control. One method of monitoring the performance of the analytic system is to systematically assay standard materials, whose sampling characteristics are carefully controlled. Gold assay standards are not prepared, nor can they be prepared, to account for both sampling and analytical errors. It is not possible to send coarse material to a lab for both preparation (i.e., comminution and splitting) and fire assaying and then come to conclusions only about the fire-assay process. Because most gold ores are very heterogeneous, sampling errors would, in most cases, completely mask the contribution of the analytical errors. Assay-standard material is prepared only to assess the accuracy and variability in the fire assay process. Because the objective of the assay standard is to provide information about the fire assaying, it is necessary to control the sampling error of the standard material, so that it is only a minor constituent of the discrepancies observed in any assay results. To do this requires that the particle size of the standard material be reduced to a point where the relative standard deviation of the sampling error (i.e... the standard deviation of the errors divided by the average gold content of the material) is 2% or less. For all but very homogeneous mineralization, this means that the material must be reduced to 100% -150 mesh before the sampling errors are adequately controlled. However, even reducing the particle size can contribute to sampling problems. The liberation of gold may cause segregation that can cause large sampling fluctuations that are not easily controlled while maintaining the desired grade. Because, in most cases, the standard material would already be in the "pulp" state when it is submitted to a lab for assay, it is not possible to entirely conceal the nature of the sample from the lab. This is a problem inherent in using assay standard material. Because of the contribution of sampling to error generation in the assay process, the use of "coarse" material does not solve the problem of submitting a totally "blind" standard to the lab. In the sections that follow, the selection, preparation, testing and use of gold fire assay standard material is discussed. While some may dismiss the production of standard material as folly, it is possible to produce and utilize standard material to stabilize and improve the fire-assay process to produce more reliable assay results. Material selection It is desirable to use material that has as nearly the same metallurgical characteristics as the samples with which the standards will be included. However, this is usually difficult. For many reasons, including the particle size at which a significant amount of the gold mineral is liberated, the sampling characteristics of even -150-mesh material may preclude the use of geologically and metallurgically similar ore as a standard. It is usually easier to get material having desirable grade characteristics with the necessary sampling properties than it is to find geologically and metallurgically similar material with the required sampling characteristics. High-grade standards are especially difficult to find and prepare. This is because, as grade increases, the size of the gold particles usually increases. Larger gold particles are liberated and tend to segregate during comminution, and the homogeneity of the material cannot be maintained. For grades much above 3 g/t (0.088 oz/ton), it is very difficult to find material that has the proper sampling properties. Old mill tailings are likely candidates for assay standards. Some of these have sufficiently homogeneous mineral contents, so that the sampling errors can be effectively controlled. Where mill tailings are either not available or are not acceptable, mineralization that has exhibited homogeneous results in reassays of the pulp material is also a good candidate for the standard. Finally, the mineralized rock being sampled may (and should) be used if adequate homogeneity in the -150mesh material exists. "Adequate" ("acceptable") homogeneity is defined below.) It is important to use standards having a wide range of grades. This alone may preclude the material being

Jan 1, 1997

By C. B. Manula

A method for the feasibility assessment of open-pit operations using conventional shovel/ truck systems to mine steeply pitched coal seams has been applied at The Pennsylvania State University. Three computer models were developed for the analysis: a geology and reserves model (GEOL), an open-pit materials handling simulator (OPMHS), and a cash flow model (CASH) (Manula, Albert, and Burgos, 1976). GEOL provides the basic mining data; OPMHS simulates shovel/truck performance related to pit profiles and average mining locations to provide productivity rates needed to size the system; and CASH provides either a selling price or rate of return (ROR) for the product. The general flow of information generated by these models is shown in Fig. 1. Since the ratio of overburden-extracted to coal-produced places a definite economic limit upon a mining venture, geological data must be analyzed with the least possible manual effort to minimize computational errors. This is especially true if the property contains several seams that are steeply pitched. In this situation, a computerized analysis is by far the most efficient and effective method to determine coal reserves and waste tonnage. This chapter describes the reserve model developed at Penn State and provides an example to demonstrate its application.

Jan 1, 1979

By G. T. Adel, W. Z. Choi

In previous work at Virginia Tech, a population balance-model describing the simultaneous processes of size reduction and mineral liberation has been developed. Experimental verification of this model, however, has been limited to a binary mineral system containing only one composite particle class. When considering multiple classes of composite particles, estimation of model parameters becomes much more difficult. In the present work, a procedure for estimating model parameters for a multiple-composite- class model has been developed. Emphasis is placed on direct experimental determination of these parameters. The physical significance of the breakage rate function and the liberation function in characterizing the liberation process is also discussed.

Jan 1, 1987

By R. K. Mehta, G. T. Adel

A review of the literature reveals that methods for simulating the coupled behavior of size reduction and liberation are limited to binary mineral systems containing one composite particle class. The aim of this paper is to describe the development of a mathematical model to simulate such behavior for binary and ternary systems containing multiple classes of composite particles. A modified Levenberg-Marquardt algorithm and a finite difference Jacobian are used in conjunction with the developed model and a set of constrained equations to estimate all kinetic parameters. This estimation scheme is validated far a binary ore (sphalerite-dolomite) with five composite particle classes using experimental data.

Jan 1, 1991