Search Documents

By Frank W. Schmechel

The subsidence monitoring program at the Old Ben No. 24 Mine was planned in 1976 as part of the on- going demonstration of longwall mining. The construction and installation of the network of surface subsidence monuments was started in Play of 1976 and completed four weeks later after which an initial reference survey was made of all surface monuments. Mining of the first longwall panel started in September of 1976 and was completed in May of 1977. Mining of the second panel started in August of 1977 and is continuing at this time. The Automatic Data Acquisition System (ADAS), which is the subject of this paper, was installed over the second panel on March 29, 1978 near the panel center (Figure 1) and approximately 104 meters (370 feet) in front of the face position at that time. Mine No. 24 is located approximately 5 kilometers (3 miles) Northwest of Benton, Franklin County, Illinois. Coal is being mined from the Illinois (Herrin) No. 6 seam which is at a depth of about 189 meters (620 feet) at the site. The Herrin No. 6 is up to 2.7 meters (9 feet) thick in the mine but a constant thickness of 2.1 meters (7 feet) is being mined by the demonstration longwall with both roof and floor coal being left for stability. Although the seam is flat laying at the mine, it dips north- ward regionally. Topographically, the surface over the demonstration panels is essentially flat and low laying with several areas of standing water. The Rend Lake Dam (United States Army Corps of Engineers) is about 305 meters (1000 feet) north of the demonstration site.

Jan 1, 1979

By W. J. Mahoney

A good quality assurance program at a coal mine or power plant is accurate, timely, and consistent. The quality analysis is accurate due to a complete sampling of the coal stream loaded into the unit train. The sample analysis is accurate because standardized testing procedures are applied. Once the analysis is completed, the results must be communicated to the electric utility in a timely manner. The electric utility needs the results to better manage the coal inventory at the power plants. A quality assurance program can also help the mine deliver a consistent product to the electric utility's power plants. The importance of the three major tenants for a good quality assurance program: accuracy, timeliness and consistency, are based on major changes that are taking place in the electric utility industry.

Jan 1, 1994

By Kazmierczak J. B., Klein E., Kinscher J., Lizeur A., De Santis F.

In this work, we propose to implement machine learning methods for the automatic classification of mining-related seismic data. The approach retained for the classification is based on a Convolutional Neural Network (CNN) which has been tested and applied to two different mining datasets: the active ore mine of Garpenberg (Sweden), currently under exploitation, and the abandoned coal mine of Gardanne (France), where mining stopped in 2003. The first step of the approach consists in creating a well classified (manually) database of seismic signals separated in different classes as a function of the seismic sources. The selected database is then divided into two groups: train, containing the 70% of the signals, and test, which contains the remaining 30% of the signals within the selected database. The learning phase of the algorithm consists in creating a classification model based on the train group, which is further validated on the test group. The application of CNN for the automatic classification of Garpenberg and Gardanne seismic data shows, respectively, that about 88% and 98% of the seismic events of the two sites can be properly classified. These results demonstrate that machine learning could be a powerful tool for microseismic monitoring in mining and post-mining environments, which could be further extended to the whole automatic processing of seismic data, including signal’s classification as well as microseismic event’s localization.

Apr 26, 2022

By K. M. Reim

Planning the development of the Quartz Hill molybdenum open pit mine in Southeast Alaska required a number of special considerations. Located in mountainous glaciated terrain, about 3.8 m (150 in.) of annual precipitation (with annual snowfall over 10.2 m (400 :in.) was a primary consideration. Mine planning included muskeg and snow removal, avalanche control, clearing timber, water quality control, dust control, seismicity, mine schedule, work force and reclamation. Quartz Hill is in an environmentally sensitive area which has required extensive environmental baseline data collection, four Environmental Impact statements (EIS) and a large number of permits.

Jan 1, 1988

Paper and paperboard manufacturers need to quantify the carbon footprint and environmental impact of their products to satisfy market, social and government demands. Coated paper products contain minerals, such as kaolin and calcium carbonate, at significant levels; some coated paper grades have mineral contents as high as 45% by weight. Some uncoated paper has no mineral content, but most uncoated paper contains some mineral to improve appearance, process efficiency and cost. Super-calendared paper grades can contain levels of mineral up to 35% by weight. This paper describes how to calculate the carbon footprint of kaolin and calcium carbonate minerals used for white pigments. The carbon footprint of these minerals strongly correlates to the primary energy sources, final product form and energy used to calcine kaolin and lime. Kaolin and calcium carbonate pigments have a favorable impact on the carbon footprint of paper and paperboard products by directly substituting for fiber and by reducing the energy needed for paper making. Key words: Kaolin, Calcium carbonate, Paper production, Carbon footprint, Lifecycle analysis

Jan 1, 2010

By D. A. Huggins

Column flotation is finding increasing use in the flotation of copper, molybdenum and other heavy metals and coal. Columns have proven operational, cost and metallurgical advantages which caused us to investigate their use in the proposed Escondida flowsheet. A comparative pilot plant test with 35 tons of ore showed that one column can replace three stages of cleaning and result in a significantly higher concentrate grade with no loss in recovery.

Jan 1, 1987

Strainburst phenomena, generally characterized by a sudden release of energy in a volume of highly stressed rock, are often encountered in such situations like crown pillar bursts in cut-and-fill mining, face bursts at development headings and floor bursts in deep shaft sinking. This paper describes a simple FE modeling approach which leads to the calculation of the energy release rate (ERR) and the total energy storage rate (TESR) in the rock mass around the openings. The merits of using such energy parameters in the analysis of strainburst problems to identify areas of high energy release/storage are discussed. However, much site-specific back analyses are needed to better understand how strainbursts and energy parameters are inter-related.

Jan 1, 1998

By N. Teasdale

The Bousquet #2 deposit, located within the Blake River Group in the Abitibi Greenstone belt, midway between the towns of Val d'Or and Rouyn-Noranda, exhibits all of the distinguishing characteristics of volcanogenic massive sulfide (VMS) deposits. As such, the deposit can be compared with other gold-rich VMS deposits such as the world-class Home deposit in Rouyn-Noranda, Quebec, Canada and the Mount Morgan deposit near Rockhampton, Queensland, Australia.

Jan 1, 1995

By Everett H. Dobbs

The Tripoli deposits in the southwest corner of Missouri In Newton County and the northeast corner of Oklahoma in Ottawa County, located in the vicinity of Seneca, Missouri, contains an unusual and peculiar form of silica which has not been found any other place in the world. Its outstanding characteristic is the physical structure of the individual particle, The particle structure of the Missouri-Oklahoma type Tripoli accounts for its market. It is a soft, friable, porous, double-refracting silica of the chalcedony variety, The particle is porous, has a fibrous structure, no sharp edges or comers, ad an average size of less than .01 millimeter, It varies from 90 to 98 per cent Si02 with less than 1 per cent free silica in the form of quartz, 24; has ignition loss of 1 per cent and fractional percentages of iron, alumina, lime, etc.

Jan 1, 1960

By M. T. Smith

In a 2,000 square mile area of Polk, Hillsborough, Hardee and Manatee Counties in Central Florida is located one of the richest known deposits of the life-giving mineral, phosphorus. Under layers of sand and clay are found millions of tons of phosphate rock, best source of this element which is necessary to all forms of life - plant, animal and human. Phosphorus is an irreplaceable ingredient in all complete plant foods, and more than 90% of Florida's vast production goes to enrich the croplands of the United States and many other areas of a hungry world. In addition to this, it has wide industrial use in the manufacture of many products - detergents, baking powder, carbonated beverages, steel, matches, munitions, glass, insecticides, dyes, water softeners and innumerable others. Not only does phosphorus make life possible for us - it also helps us to live longer and better.

Jan 1, 1962

By H. Suharyono

The results of an experimental study of polymer-induced flocculation of clay suspensions in continuous, stirred-tank reactors are presented. The effects of polymer dosage, mixing time and mixing intensity are shown to be generally similar to those observed for equivalent batch systems, but flocculation appears to be generally less effective in the continuous process. Settling rates are lower and supernatant turbidities are higher for the continuous system. It is postulated that non-equilibrium effects due to simultaneous polymer adsorption and floc growth can be exploited so as to enhance flocculation in batch systems. The nature of the continuous process, however, offers less opportunity for taking advantage of such effects. Conditions in a continuous flocculation system inherently lead to a closer approach to equilibrium.

Jan 1, 1994

By A. G. Naguib

In essence, any magnetic separator operates on the basis of imparting a preferential magnetic force on particles of higher magnetic susceptibility which are to be separated from particles of lower magnetic susceptibility. A certain amount of directional deviation to the particles takes place thus allowing for collecting each category of particles separately. The forces in action on particles in a wet magnetic separator of the established designs can be analyzed in a simple manner as shown in Figure 1.

Jan 1, 1972

By S. K. Sharma

The Bureau of Mines' rapid method of dewatering fine-particulate slurries uses extremely high molecular weight polymers. These polymers form large, strong flocs which can be dewatered by sieving or sedimentation. However, sometimes these flocs deteriorate rapidly if water is not removed immediately. During field tests, clay slurries have been encountered that could have been dewatered economically if it were not for the rapid floc deterioration. A kinetics study was conducted to determine the rate of kaolin-PED floc degradation in which polymer addition, to bring the flocs back to their original condition, was used to determine the extent of floc decay. Results showed that the amount of polymer added, to replace polymer lost by spreading, was less for the lower PEO concentrations. For this clay-polymer system, floc breakage as judged by polymer additions followed first order kinetics. It was also found that the addition of fluoride ion stabilized the kaolin flocs.

Jan 1, 1992

By Q. X. Yun

This paper presents a new approach to optimize the transportation system in open-pit mines. The new approach employs artificial intelligence, fuzzy sets, dynamic programming and CAD technique to determine the transportation system. The determination consists of 4 phases: initial selection, road alignment, final decision .and open-pit drawing.

Jan 1, 1992

By M. J. DeJong, R. J. Mair, S. Ritter, G. Giardina

"For urban tunneling projects it is essential to predict and prevent building damage. Although various case studies and experiments have shown that buildings considerably modify greenfield soil movements, widely accepted damage assessment methods neglect this soil-structure interaction and simplify structures as linear elastic beams. This paper summarizes an experimental investigation of the response of more realistic structures to tunneling-induced deformations. Small scale structural models with façade openings and brittle material properties were 3D printed and tested in a geotechnical centrifuge. Soil and structure displacement data were obtained by image-based measurement. Results demonstrate that structures notably mitigate differential greenfield ground displacements. It is also shown that maximum soil settlements, horizontal soil displacements beneath the structure and structural damage in the form of cracking significantly depend on the position of the structure in the settlement profile. The results provide a basis from which to predict building settlement response with greater certainty. INTRODUCTION With continuing population growth and increasing urbanization expected in the next decades, there is an urgent need for a next generation of infrastructure. It is likely that a large part of this infrastructure will be underground. Such creation of urban underground space frequently involves the excavation of shallow tunnels in close proximity to existing structures and utilities. For example, along the Crossrail project in London more than 1,200 structures are located within a possible influence area of the tunnel construction (Torp-Petersen and Black 2001). The assessment of building damage plays a vital role throughout the planning, design and construction stage of urban tunneling projects. However, while predictions of tunneling-induced deformations in the greenfield can generally be made with some confidence, much uncertainty exists about how structures interact with ground movements arising from tunnel construction."

Jan 1, 2016

By Chris D. Breeds

Northwest Boring, Inc. (NWB) deployed a skinned up AVN 2000AB Microtunnel Boring Machine (MTBM) to install 7.5-foot long, 118-inch outer diameter reinforced concrete pipe (RCP) sections along an alignment between the Fremont (FRS) jacking shaft and the 3rd Avenue (3RS) receiving shaft for the Ship Canal Water Quality SCWQ Project. The alignment includes: a 67-foot long straight section, a 367-foot long curved section excavated along a 650-foot radius curve, followed by a 182-foot long straight section. This paper describes the project including planning and design, manufacturing, equipment installation in the 90-foot-deep FRS jacking shaft, egress through the secants and microtunnel operations required to complete the shaft and install the required casing pipes.

Dec 1, 2022

By George F. McIntyre

The subject of this paper is mineral processing chemicals - how they work and where they end up environmentally. First of all, it is necessary to recognize that water is the most universally and widely used chemical used by the mining industry to separate desirable minerals from unwanted wastes, sands, and slimes. Of the total world's water supply, over 97 percent is found in the oceans. Another two percent is tied up in the ice caps, leaving roughly only one percent for us to work with. This one percent is distributed either as ground or surface water and makes up the bulk of all water used industrially. Even with such a small proportion available for immediate use, there appears to be enough fresh water to meet our needs for at least another hundred years. This availability, however, depends heavily on how we handle our waste waters, how we process them, and how we plan for their reuse. Certain governmental agencies have been charged with the task of setting up standards of water quality which must be met prior to environmental discharge. There is even discussion of zero discharge from industrial operations. Due to limited supply and availability, the mining industry has always been forced to reuse its process water or to treat it prior to discharge. Consequently, we are in an enviable position and are presently able to live with the environmentalists demands. To stay on top of the situation, it is necessary to continually concern ourselves with the .effects of changing orebodies and reagents on the final mill effluent. From a process standpoint, it is also important to recognize the impurities of plant recycle water and how they might tend to influence overall operations

Jan 1, 1974

By K. Feledi

"A booster fan is an underground mechanical ventilation equipment installed in series with a main surface fan that is used to boost the air pressure provided by the surface main fan passing through it. As mining continues to expand and go deeper, the need for improved and efficient ventilation increases. This has led to the use of booster fans and other auxiliary ventilation devices in underground mines. This paper details experiments and results carried out at Missouri S&T Experimental Mine that investigated air leakage and recirculation caused by the use of booster fans. The results were compared with the situations where booster fans are used and not used.The variables considered were the booster fan blade angle and the fan combinations. Air quantity measurements were taken at each individual stopping under a number of scenarios and across four blade angle settings. The first set of situations examined were; the main surface Joy fan only running, the main Joy, and the west booster fan running, and the main Joy fan and east booster fan running. Observations were made which lead to the conclusion from the experimental analysis that booster fans affect the behavior of leakage and recirculation. The locations of the booster fan and the blade angle setting have the most effect on leakage and recirculation. To limit the potential for system leakage and recirculation, the location and size of a booster fan in a ventilation system should be thoroughly evaluated.INTRODUCTION Missouri S&T Experimental Mine ventilation system The Missouri S&T Experimental Mine has two shafts. One currently serves as the main intake shaft. Air is forced through the main shaft by a Joy Manufacturing Vane Axial fan and follows the direction shown on the map on Figure 1. The air is currently naturally exhausted through the Wheeler portal. As indicated on the map there are eight stoppings in the mine, with stoppings number 2 and 8 fitted with man doors. The mine also consists of three raises which are either fully or partially blocked, two portals with one acting as an exhaust and the other generally closed by a hydraulic Kennedy door."

Jan 1, 2015

By H. P. Ehrlinger

The Negociacion Minera Santa Maria De La Paz mining operations are located at La Paz (some eight miles West of Matehuala), State of San Luis Potosi, Mexico. These operations consist of a single copper-silver property, called the Dolores mine and a number of silver-low base metal properties. The ores from these several mines are transported by rail, or truck, to the central milling unit. The milling unit has two separate sections to treat the two types of ore. The ores from the several silver-base metal mines are mixed at the mill as they arrive. Up to the present time the silver-base metal ores have been milled to produce a bulk concentrate which carries valued in gold, silver, copper, lead, zinc, cadmium and considerable arsenic. In such concentration the zinc and cadmium values are lost to the operations in their liquidations as they are shipped as lead concentrates. Since these ores have exceptional quantities of arsenic which is concentrated in the milling process, these bulk concentrates have to be sent to a smelter for pre-smelting operations to remove the arsenic.

Jan 1, 1964

By D. M. Stephens

Feeder-Breakers were an unknown but much needed piece of machinery when U. S. underground coal mines started converting to more efficient belt haulage of the R.O.M. coal as compared to conventional methods that the 1950's offered. These simple electromechanical machines offered efficiencies in three areas: (1) they contained a surge hopper that allowed a "load' of coal to be dumped without delay; (2) this material was fed horizontally by a drag chain conveyor into a rotating carbide pick breaker that broke all oversize material into a beltable size, and (3) it fed this broken material onto the belt conveyor at a rate conducive to its design. Since its introduction, the Feeder-Breaker has evolved from that first low capacity, low breaking force machine to today's model capable of breaking materials up to 5 MOHS in hardness and having throughput capabilities exceeding 3,000 TPH with availability in the 90 percentiles.

Jan 1, 1985