Search Documents

By R. L. Hills

America's industry uses about 44% of the total energy consumed by the nation directly as fuel burned in industrial plants or indirectly as fuel burned by utilities to provide electric power. In addition, industry requires raw materials or feed stocks derived from fuel sources or having fuel value. This represents about 11% of total U. S. energy consumption, bringing industry's portion to about 55%. Adding that portion of energy consumption required by the transportation sector to move raw materials, intermediates, and finished products, the total energy impact of industry approaches 213 of total U. S. consumption. It is obvious that American industry has the largest share in the task of balancing energy demand and supply. What are we going to do? -- We must increase the supply of energy and increase the beneficial results obtained from each unit expended. Both avenues, unfortunately, are limited in extent and speed. Increases in supply cannot occur without drastic and permanent increases in cost. These increases in cost are un- desirable and inflationary but do provide incentive for the rational businessman to expend the effort and money required to improve the effectiveness of energy in industry.

Jan 1, 1975

By Q. X. Yun

This paper presents a new approach to optimize the transportation system in open-pit mines. The new approach employs artificial intelligence, fuzzy sets, dynamic programming and CAD technique to determine the transportation system. The determination consists of 4 phases: initial selection, road alignment, final decision .and open-pit drawing.

Jan 1, 1992

By Isabel F. Barton, Matthew J. Gabriel, CARSON ROBERTS, JOHN LYONS-BARAL, LEON DUPLESSIS, Mark D. Barton

Geometallurgical characterization is increasingly used in the mining industry to model ore types, predict process performance and identify potential recovery issues ahead of time. However, most geometallurgical assessments are based on bench- or laboratory-scale analyses of relatively sparse samples, leaving most of the orebody characteristics known only by inference until the rocks are actually mined. In this pilot study, we test drone- and tripod-based hyperspectral imaging for mapping mineralogy across mine highwalls, dumps and leach pads. The results show that hyperspectral imaging can successfully map the types and distribution patterns of key minerals (especially carbonates, sulfates, clays, other phyllosilicates) and other important features (such as lixiviant ponding on leach pads), bringing geometallurgy into the field to provide crucial inputs to process decisions.

By M. M. Botz

Cyanidation tailings which are disposed in a surface impoundment experience a loss of cyanide due to natural degradation, frequently reducing the cyanide concentration to very low levels. Quantifying cyanide losses in terms of pond geometry, local weather conditions and feed solution chemistry has been largely empirical though in many cases mining operations rely on surface impoundments to reduce cyanide to below an internally regulated concentration or an effluent limitation. To permit a more quantitative evaluation of cyanide losses in an impoundment, a computer simulation was developed to estimate the losses of free, WAD and total cyanide due to dissociation, photolysis and volatilization. Results of the model are compared against data collected for a North American tailings impoundment during 1998.

Jan 1, 1999

By KALLAM VK REDDY, VADAPALLI SANJANA, Veerendra Singh, Gajanan Kapure

Mining activity around the world has increased significantly to meet stepped-up demand for various metals [1]. Apart from the target minerals, mining also generates huge amounts of unwanted minerals that exit the mines as overburden. Due to the active mining activity, high-grade mineral resources are being depleted, leaving inferior-quality ores [2]. The mining of low-grade ores further increases the amount of overburden/waste per ton of metal equivalent of ore mined. Currently, overburden and other mine waste is most commonly used in the construction industry and as feedstock for making cement and concrete, but the overburden can also be used as a source of valuable minerals and metals [3]. 

By T. E. Wilson

In conjunction with experiments to improve the particle size preparation of coal bore cores prior to washability testing, discrete-event breakage of coal, shale and homogeneous low-strength concrete cores was studied. Breakage of individual size classes by drop-shatter and by incremental tumbling in an end-over-end hand-driven tumbling cylinder revealed systematic changes in the breakage function, namely, that breakage in any size class diminishes as the number of events increases. The effect of the fines removal enhances the breakage of harder material (having lower grindability indices), but appears to have less effect for softer material.

Jan 1, 1998

By L. M. English

A basic model was developed to help assess methane control needs for the longwall mining of coal in gassy areas. Rather than depending on reservoir and rock mechanical theories, it uses an empirically determined gas emission rate as an input, and it operates on the assumption that, within a specific region and zone, gas emissions will be relatively equivalent for uniform incremental volumes of gob created by mining. The computer program divides longwall panels into segments, keeps track of the face advance and generates emission rates and volumes for both the entire panel and for individual zones within the panel by summing values for all undermined segments. This model can aid in the determina¬tion of the number, size and location of vertical wells or other methane-control applications that are needed for gob gas control.

Jan 1, 2000

By M. C. Roberts

The consumption of industrial minerals, like most other commodities produced from the earth, depends on the demand for the goods and services that use these materials. Minerals are not generally used directly by final consumers (table salt is a notable exception) but instead are used to either make products that are then purchased by customers, or the minerals are used to make industrial products that eventually contribute towards producing other goods and services. Therefore the demand for industrial minerals in most uses is derived from the ultimate demand for goods and services by consumers. The problem for producers of industrial minerals is that the demand for their mineral product fluctuates greatly in response to the changes in the production of goods and services over the course of the business cycle. In this respect, the producers of industrial mineral are innocent victims, subject to market fluctuations outside of their control. Because the demand for most minerals depends on the demand for the product and because minerals typically make up a minor portion of the costs of producing the product, changes in the price of the mineral often do not influence demand for it to a significant degree in the short run. This is described as a very low price elasticity of demand, as shown by the steep slope of the hypothetical demand curve in Figure 1. This demand curve shows that changing the price of the mineral does not alter the quantity demanded very much, but shifts in the demand curve will be the important determinant of the quantity of the mine.ra1 that is sold. The shifts are caused by the changing demand for the products using the mineral over the course of the business cycle.

Jan 1, 1994

By Frank J. Hirner

Economic open-pit and surface mining often call for ever increasing volumes of lower grade materials. So it is important, often critical, to develop precise expense and production estimates for the large electric mining shovels now in use. An electric shovel's basic application is to "shovel up" material, starting at ground level with the dipper moving up into a working face or bank. It's impractical to dig below ground level with a shovel, except briefly or in unusual circumstances. The shovel working face is "the bank," whether the material is dug from natural bed or blasted. The shovel's digging attachment, the boom and dipper handle, is built in standard and long range configurations. A standard digging attachment is normally used for loading into haulage equipment. The long range attachment is normally used for side or hack casting to a spoil pile. It is also used fir loading into haulage equipment placed above shovel ground level, as in some coal loading applications. Shovel clipper size and hauler capacity should he matched so that a hauler can he loaded in three to four shovel work cycles. Five cycles is usually the limit of good practice. If fewer than three cycles are required, the hauler is too small. More than five cycles indicates possible excess harder waiting time for loading, or shovel waiting time for too few haulers. Full dipper loads, including the last dipper or ''pass, " are essential for economical shovel and hauler match. Consistent need for a final partly full dipper to fill the hauler shows an improper match between the two.

Feb 1, 1981

? The U.S. depends on minerals for economic growth and development, and for national security and defense. ? Public lands are an important, long-term source of essential minerals. ? Access to public lands for mineral exploration and development has become more difficult as large tracts of land have been designated for other uses. ? Mineral-bearing areas on public lands are routinely withdrawn or restricted from development before comprehensive resource inventories and economic assessments have been made.

Jan 1, 2011

By Vincent J. Murphy

INTRODUCTION Geophysical applications to engineering projects are usually considered for reconnaissance exploration, and for some preliminary design phases. Recent experience indicates a growing need and a greater number of requests for measurements during construction. This is particularly true where seismic velocity values are related to strength properties of rock. Typical project objectives during construction are: dike and tunnel realignments required by surprise conditions encountered during foundation preparation; checks on grouting effectiveness which require velocity measurements before and after grouting; and dynamic moduli measurements along the walls of tunnels and deep excavations. This paper considers one of the on-site seismic applications that is rather simple and straightforward, and yet has few references in the literature. The specific objective is the measurement of seismic velocities (both "P" waves and "S" waves) for determining the thicknesses and dynamic moduli values of loosened zones of tunnel wall rock. PRE-EXCAVATION SEISMIC METHODS The seismic methods suitable for engineering project studies are well known and especially suited for routine site reconnaissance; these are illustrated in Fig. 1. The seismic refraction profile with a

Jan 1, 1997

By Rodney H. Sergent

After being forgotten or ignored for nearly 100 years, the ability of bromine chemistry to extract gold from ore has been rediscovered. While bromine chemistry is similar to chlorine, there are some important differences. Bromine in its elemental form is a dense, fuming, red liquid. Elemental chlorine is a gas and requires a substantial amount of equipment to handle, store and deliver to solution. Bromine has an advantage in its ability to rapidly and completely oxidize heavy metals to water soluble halide salts. The first patent for use of bromine chemistry for gold extraction was issued in 1881 (1). By 1895, work done in Colorado concluded well roasted ores required approximately 1-1/2 lbs/ton of elemental bromine for superior extraction of metals (2)). At that time, bromine was deemed to be cost effective vs. chlorine even though it was more expensive on a pound basis than chlorine. The advent of cyanide technology virtually eliminated both chlorine and bromine from consideration for leaching of ores. Cyanide was so inexpensive that it made deposits requiring unique technologies unattractive for mining. Only since the deregulation of gold price has bromine/chlorine technology been considered for those ores not amenable to cyanide. While chlorine has found its way into the pretreatment steps, bromine is just beginning to realize its niche in the marketplace.

Jan 1, 1998

By B. J. Sauer

Misapplication of ac induction motors for mine crusher and mill applications has long been a frustration for the driven equipment supplier and the mine operator. Proper selection of ac induction motors is critical to providing efficient production. This paper focuses on the selection of ac induction motors for gyratory crusher, conecrusher and grinding mill applications. The criteria for motor selection includes: proper enclosure, driven equipment torque requirements, bearing life, temperature rise, starting requirements, ambient temperature, altitude and accessory requirements.

Jan 1, 2002

By Pooyan Asadollahi, Praveen Krishna, Michael Joye

"Durability design for underground structures is an increasing focus of designers and owners in the underground construction industry. Many owners have expanded their requirements for durability design, with specific requirements for structure lifecycle and designer certification of structural durability. This paper describes current trends and best practices including: defining the underground structure lifecycle, historically durable underground structures, design methods for underground structure durability built of reinforced concrete, and durability of materials. Criteria to be used for defining end of structure life and owner’s maintenance responsibilities are crucial to lifecycle contract requirements. Current practices of several major owners are presented. Design methods are presented including United States code requirements. Current best practices for enhancing the durability of materials used in underground construction are discussed including: low permeability concrete, steel reinforcement concrete cover, the use of steel fiber, and testing for verification. INTRODUCTION Durability design is increasingly being recognized as an essential component of good design practice. Infrastructure owners recognize that to serve the public interest, constructed facilities must be lasting and durable. The public understands that structures with limited service life result in increased costs and add to their daily inconvenience with frequent repair and reconstruction. Engineers are increasingly asking not only is the structure strong enough but will it last for generations. Durability design requirements are no longer just adherence to some accepted practices, but are based on analytical approaches, with results that can challenge our beliefs in what construction materials and details result in a durable structure. This paper describes current industry requirements and practices for durability design of underground structures, and offers some suggestions regarding future trends and developments. SERVICE LIFE DEFINITION The service life of a structure is the sum of the time to onset of deterioration, called initiation period (ti), and the subsequent time period of deterioration ending when the structure is no longer functional, called propagation period (tp). Figure 1 shows a conceptual service life diagram. These time periods can be substantially affected by the level of maintenance performed during the life of the structure."

Jan 1, 2016

By Kevin L. Purdy

Chemical dewatering aids for mineral slurries generally fall into two classes: surfactants and flocculants, which can be used separately or together. Current industrial use of both types of reagents is summarized for sulfide and non-metallic minerals, as well as uranium and gold leach residues and coal refuse. Laboratory testing for reagent selection is briefly discussed along with reagent preparation. Chemical properties of the reagents which affect the suitability for particular applications are analyzed. [BLANK PAGES - Are in the original]

Jan 1, 1986

By S. Kesler

Rössing Uranium Limited has operated since 1976 a large open pit uranium mine and extraction plant at a remote site in the Namib desert, South West Africa/Namibia. The geology (Berning, I., et al. Economy Geology) and the technical aspects concerning mining, grade control and metallurgy have previously been described (Rössing Uranium, Mining Magazin and Whyllie, R.J.M. "Rössing Uranium reaches rated production", World Mining). The improvement of leach 'extraction has been reported in 1984 (Kesler, S.B. et. al. "Uranium extraction at Rössing") and the installation of a central process control system has been described (Kesler, S.B. et al. "The introduction of a central process system at Rössing"). At the beginning of 1983 a decision was made to develop a computer system for metallurgical plant optimisation which included mass and volumetric balances, analytical assays for up to 5 chemical elements and the costs for the major consumables. Within 10 months this computer system was developed and implemented. A large number of test runs were made and computer studies were undertaken. The metallurgical division now has a scientific tool for production; planning for actual comparison with plant results and for strategic investigations and decision making.

Jan 1, 1986

By R. L. Nielsen

The thematic mapper (TM) aboard Landsat II records image data at seven wavelength intervals or bands. Three record the visible region; three record reflected IR energy. A false color image combining bands 7, 4 and 2 rendered as red, green and blue respectively provides maximum discrimination of rock types in arid regions. Structural analyses and interpretation defines regional structures, large volcano-tectonic features intrusive complexes, all which localize mineralization. Special digital processing using the ratio: Band 3 / Band 1 can identify limonites and other iron minerals. The ratio: Band 5/ Band 7 identifies clays and alunite. These ratio images show features and patterns of hydrothermal mineral systems: ?patterns of sulfide and alteration zoning in large porphyry systems, and zones of strong silica, quartz-alunite-illite, and pyrite-sericite in epithermal centers. Thus, digitally processed Landsat TM images are a cost effective and rapid means to recognize altered areas and define targets for large mineralized systems.

Jan 1, 1995

By N. P. Reddy, Y. J. Wang

This paper describes an experimental setup for multiple fan ventilation systems at the ventilation laboratory of the West Virginia University Department of Mining Engineering. Housed in a 30-ft x 70 -ft room, the experimental setup consists of three 18-in., variable-speed, axial flow fans; an 18-in. -diam, fiberglass tubing; associated fittings for arranging networks; and a picot-tube measuring and data-acquisition system. The fiberglass tubing and fans can be organized into non-planar networks of two or three fans. The setup is mainly designed for studying the characteristic curves, operating points and fan stall for multiple fan ventilation systems.

Jan 1, 1993

By Thomas E. Weyand, Wolfgang Baum

PMET is engaged in the development of reuse operations for process wastes from the natural resources industry. Most of the current remediation practices with mining wastes are concentrated on stabilization techniques. Once stabilized, valuable resources are no longer readily available for recovery and reuse. Additionally, stabilized materials, unless protected from weathering influences, pose lingering liability for the generator.

Jan 1, 1992

By S. D. Thompson, G. T. Lineberry, A. J. Basu

Conveyor belt haulage has become the preferred mainline transport method in underground coal mining, especially for multi-unit mines. Proper designs for belts (width and speed) and surge bins (placement, capacity, and discharge rate) are necessary to achieve efficient mine haul- age. Two computer simulation models, CMBCS and BELTSIM, available for designing these parameters were compared. These comparisons included modeling, input data requirements, statistical flexibility, accuracy of simulated loading, and execution time.

Jan 1, 1991