Search Documents

By P. L. Sibrell

Previous research by the U.S. Bureau of Mines showed that autoclave cyanide leaching of used automobile exhaust catalysts for recovery of platinum group metals (PGM) was technically feasible. This work involves a more detailed investigation of the chemistry of the dissolution of PGM in cyanide solutions. The PGM species in solution identified by ultraviolet spectroscopy. Pt and Pd cyanide complexes were square were The planar in geometry, while the Rh complex was octahedral. The rate of dissolution of the PGM was also investigated using a rotating disk technique. Dissolution rates increased in the order of Rh, pt, and Pd, respectively.

Jan 1, 1994

By David A. Summers

Historically, the presence of methane has been a problem, mainly in and around the working areas of active coal mines, and only in these area has drainage been considered. Drainage, where practical, has been achieved through the drilling of holes forward into the coal and the surrounding strata from the working area. These holes generally have been short in length, although where methane drain- age operations around a longwall face have been undertaken, the holes have had to be longer in order to adequately drain from the center of the face into the access gate roads. In recent years, attempts have been made to degasify the coal seams in advance of mining, without disruption of the mining cycle. This is done by drilling much longer horizontal holes through the coal in advance of the working area. Under the aegis of the Federal Government, methods have also been developed for draining seams of coal of their methane content in advance of mining, but from shafts sunk from the surface, without using the active area of the mine as the location for the drill holes.

Jan 1, 1979

By Frank W. Schmechel

The subsidence monitoring program at the Old Ben No. 24 Mine was planned in 1976 as part of the on- going demonstration of longwall mining. The construction and installation of the network of surface subsidence monuments was started in Play of 1976 and completed four weeks later after which an initial reference survey was made of all surface monuments. Mining of the first longwall panel started in September of 1976 and was completed in May of 1977. Mining of the second panel started in August of 1977 and is continuing at this time. The Automatic Data Acquisition System (ADAS), which is the subject of this paper, was installed over the second panel on March 29, 1978 near the panel center (Figure 1) and approximately 104 meters (370 feet) in front of the face position at that time. Mine No. 24 is located approximately 5 kilometers (3 miles) Northwest of Benton, Franklin County, Illinois. Coal is being mined from the Illinois (Herrin) No. 6 seam which is at a depth of about 189 meters (620 feet) at the site. The Herrin No. 6 is up to 2.7 meters (9 feet) thick in the mine but a constant thickness of 2.1 meters (7 feet) is being mined by the demonstration longwall with both roof and floor coal being left for stability. Although the seam is flat laying at the mine, it dips north- ward regionally. Topographically, the surface over the demonstration panels is essentially flat and low laying with several areas of standing water. The Rend Lake Dam (United States Army Corps of Engineers) is about 305 meters (1000 feet) north of the demonstration site.

Jan 1, 1979

By Daniel T. Brian, O&apos

Exploration targets and results in the mining industry are commonly summarized in terms of tonnage and grade. Business appraisals require, as additional information, the expected profit or loss implied by the physical summary. The early incorporation of knowledge gained through financial analysis computations can provide a means for economically resolving many common exploration and development problems. Examples of such applications from the activities of exploration planning, reconnaissance, land acquisition, and development planning are presented in this paper.

Jan 1, 1969

By K. M. Reim

Planning the development of the Quartz Hill molybdenum open pit mine in Southeast Alaska required a number of special considerations. Located in mountainous glaciated terrain, about 3.8 m (150 in.) of annual precipitation (with annual snowfall over 10.2 m (400 :in.) was a primary consideration. Mine planning included muskeg and snow removal, avalanche control, clearing timber, water quality control, dust control, seismicity, mine schedule, work force and reclamation. Quartz Hill is in an environmentally sensitive area which has required extensive environmental baseline data collection, four Environmental Impact statements (EIS) and a large number of permits.

Jan 1, 1988

By D. A. Huggins

Column flotation is finding increasing use in the flotation of copper, molybdenum and other heavy metals and coal. Columns have proven operational, cost and metallurgical advantages which caused us to investigate their use in the proposed Escondida flowsheet. A comparative pilot plant test with 35 tons of ore showed that one column can replace three stages of cleaning and result in a significantly higher concentrate grade with no loss in recovery.

Jan 1, 1987

By R. R. Fernández

The Newmont roasting plant in Carlin, Nevada, commenced operating in December 1994. Over the years, refractory ores and pyrite concentrates from different gold deposits constituted the feed to the facilities. Historical plant performance indicated that the roasting temperature was the main variable affecting the structural characteristics of the calcine, which in turn affected the recovery of gold by cyanidation. Gold recovery as a function of roaster temperature has been closely monitored since October 2000. The original design temperature was 550° C. Lower roaster temperatures of around 500° C resulted in a gold recovery increase of more than six percent. This increase was directly related to an increase of the surface area of the calcine. The implementation of an ?intelligent? process control system helped significantly in achieving steady low roasting temperatures, thus obtaining high gold recoveries of 92 to 93 percent. Under these conditions, several roasting campaigns with high-arsenic-containing ores were conducted, which resulted in a significant decrease in gold recovery. The reduced gold recovery was caused by the loss of surface area (e.g., porosity) of the calcine as the arsenic content of the roaster feed increased.

Jan 1, 2010

By Lars A. Stålberg

"This paper will touch several of the topics covered by SDIMI 2005, including,• Sustainability indicators for the minerals industry, • Best practice of sustainable development in the minerals industry, • Social contributions,The complex issues of a company’s "sphere of influence" and "complicity" are important to every discussion of business and Human Rights. The paper will argue that to protect and promote Human Rights needs to be regarded as an integral part of sustainable development policies for the minerals industry. This implies a need for explicit inclusion of Human Rights indicators among the indicators to be applied by the minerals industry."

Jan 1, 2005

By D. A. Dahlstrom

With today's high energy costs per million BTU's, far greater emphasis is placed on increasing thermodynamic efficiency in the use of energy. America has long since discarded its previous golden age of "low cost energy" in the past ten years. Energy costs are now a very significant percentage of operating expense in industrial operations. Public utilities have felt the same influences of increasing costs in energy for the generation of electricity. Not only has the input energy expense increased seriously, but as pointed out by Blackmore in a paper, fuel costs were 53.4% of the total operating costs for American Electric Power Company.

Jan 1, 1983

By Gary E. McIntosh

This paper will discuss a U.S. Bureau of Mines project designed to assess and predict the impacts which surface coal mining will have on the regional shallow groundwater systems in the Powder River Basin. The primary objective will be met through the accomplishment of the following: (1) The design and establishment of a regional network for monitoring of shallow groundwater systems in the Basin. (2) Monitoring of the direction and rate of flow, water quality, and aquifer characteristics of the shallow groundwater systems. (3) Development of a regional groundwater simulation model with appurtenant subroutines to determine local effects.

Jan 1, 1978

By Richard A. Thomas, Liming Yuan, Wei Tang, JOHN SOLES

Lithium-ion (Li-ion) battery applications are increasing for battery-powered vehicles because of their high energy density and expected long cycle life. With the development of battery-powered vehicles, fire and explosion hazards associated with lithium-ion batteries are a safety issue that needs to be addressed. Li-ion batteries can go through a thermal runaway under different abuse conditions, including thermal, mechanical and electrical abuse, leading to a fire or explosion. The National Institute for Occupational Safety and Health (NIOSH) mining program is conducting research to prevent and respond to lithium-ion battery fires in battery-electric vehicles in the mining industry. In this study, experiments were conducted to investigate the effectiveness of different suppression systems including dry chemical, Class D extinguishing powder and water mist for lithium-iron-phosphate (LFP) battery pack fires. The effects of activation time and release time of the water-mist system on the suppression of the LFP battery (a type of Li-ion battery) fires were studied. The results of this study may be helpful for developing strategic firefighting and response plans for battery-powered vehicles used in mining.

Aug 1, 2024

By James C. Bradbury

Tripoli is a naturally occurring, finely divided form of silica found chiefly in midwestern and southeastern states and used commercially in fillers and abrasives. The name comes from the location of a silica deposit in North Africa and was applied in the latter part of the 19th century to similar material near Seneca, Missouri. Subsequently, the North African material was found to be diatomite, composed of siliceous skeletons of microscopic marine plants called diatoms, and the material's name was changed to tripolite. The name, tripoli, remained with the Missouri silica, which is inorganic in origin, and tripoli is now used to designate all naturally occurring silica that is similar in characteristics and origin to the Missouri material. Just to confuse things further, in commercial trade tripoli usually designates silica from the Missouri-Oklahoma field, whereas silica from southern Illinois, the other major producing area, is called amorphous silica. Each term, however, may be used commercially for any material, regardless of place of origin that has the characteristics or uses ascribed to material from either major producing area. For example, Engineering and Mining Journal routinely lists under "tripoli," prices "f.o.b. Elco, I11." and "f.o.b. Seneca, Mo. and Rogers, Ark.", and under "silica, amorphous," prices "f.o.b. I11 and "f.o.b. Dierks, Ark." "Soft silica" is another term that has been applied to tripoli from Illinois, west central Arkansas, and Tennessee, presumably to distinguish it from the more compact Missouri material. It has also been used in the ceramic trade to distinguish tripoli from "hard" silica, or silica flour, which is produced by pulverizing silica sand. Tripoli is produced mainly in extreme southwestern Illinois, in the Missouri-Oklahoma district in Newton County, Missouri, and Ottawa County, Oklahoma; and in the novaculite belt of west central Arkansas. Some tripoli is produced for local and specialized uses near Austin, Texas.

Jan 1, 1980

By K. V. Raj

"The development and advancement of computational fluid dynamics (CFD) has made it possible to better understand pollutant flow and distribution in deep open pit mines. Open pits located at higher latitudes, especially in the Arctic and sub-Arctic, face a unique problem due to atmospheric temperature inversion, which is prevalent during much of the winter. A three-dimensional CFD model of an actual open pit mine in the Arctic was developed to analyze the problem of pollutant growth during inversion, and mitigation of the pollutants through improved ventilation schemes. Due to the availability of mine-specific data, such as contaminant concentrations and coordinates of sampling locations, the actual 2013 pit geometry was used for model validation Concentrations predicted by the selected realizable ?-e turbulent model are compared to measured pollutant concentrations at the open pit. Pollutant concentrations at selected locations showed differences, but remained within the same order of magnitude in most cases. INTRODUCTION Computational fluid dynamics (CFD) has emerged as a useful tool for ventilation modeling in underground mines (Edwards and Hwang 1999, Purushotham and Bandopadhyay 2009, Wala et al. 1998, Xu et al. 2011). Application of CFD in open pit mines has been limited, however, since most open pit mines located at lower latitudes do not encounter considerable ventilation problems. Open pits located at higher latitudes, especially the Arctic and sub-Arctic, face a unique problem due to atmospheric temperature inversion, which is prevalent during winter. A number of Russian researchers have tried to understand the air inversion and resulting pollutant transport problem by modeling air flow phenomena in open pit mines (Baklanov and Burman 1996, Baklanov 1984, Baklanov 1995, Belousov 1985, 1989, 1995). Much of their work, however, was based on numerical models and methods of finite difference. Baklanov (2000) applied a modified ?-e and a ?-l CFD model to air flow phenomena on various terrains. More recently, Choudhury (2011) used the COMSOL CFD package for modeling pollutant transport for an idealized open pit mine. Collingwood et al. (2012a, 2012b) used a two-dimensional model for fluid flow and contaminant transport at an Arctic open pit mine. The authors have also previously presented work on CFD modeling of an actual open pit mine at high latitude (Bandopadhyay et al. 2014, Raj et al. 2015a). However, the CFD work done by the above-cited researchers lacked model validation with field-measured data. Validation of a developed model is important in assessing the quality and accuracy of the predicted results. In general, experiments are done numerous times in controlled environments to assess the validity of collected data. There are two types of assessments used in CFD simulations: (1) verification and (2) validation. Model verification is checking the accuracy of the computer codes during the implementation phase of a real-world problem, within the specific limits of accuracy (Oberkampf and Trucano 2002). Since, the pollution transport model presented in this paper used the commercial ANSYS-FLUENT CFD package, verification is not needed as the program has been tested widely, and verified numerous times."

Jan 1, 2016

By Yi Luo

Longwall coal mines are frequently located in steep mountainous areas with narrow valleys. In order to protect surrounding watersheds and residential structures, support areas are left under the valleys. However, the indirect subsidence effects to the residential structures due to the potential topography effects can be a serious problem. The present study examines a longwall mine in southern West Virginia located in an area with an average slope of about 30°, or 58%, and with an overburden depth that varies from 49 to 376 m (160 to 1,235 ft). A comprehensive investigation was carried out to assess the subsidence and topography effects, as well as other ground control issues at this site. Surface and subsurface movements and deformation were predicted and their direct effects on nearby streams and structures were assessed. The potential and indirect subsidence influences of surface topography effects were assessed. The techniques and results of this investigation are presented in this paper. It shows that the direct and indirect subsidence effects on the streams and residential structures should be insignificant. The post-mining observations agreed well with this study.

Jan 1, 2010

By W. C. Carter

In mid 1978 Inland Cement Industries Ltd. brought on-line their new one million megagram (Mg) per year cement plant at Tilbury Island, Delta, British Columbia. The Plant--Its Philosophy of Design The design of this plant began in 1974, at the beginning of the rapid rise in petroleum costs later referred to as the "energy crisis". The trend in fuel costs was clear, so one of the basic criteria for the selection of process equipment was high thermal efficiency. Throughout the process of selection of materials handling and process equipment, energy consumption was a factor in decisions. A second factor which influenced the design of the plant was its location on navigable water. The plant is designed to make maximum use of this means of transport to minimize transportation costs. All raw materials (and some fuel) are received by water, and a major portion of the cement and clinker is sent out by barge. Extensive modern dock and material handling facilities were provided to accomplish the shipping and receiving functions. A plant meeting stringent environmental regulations was the third major factor which formed the basis for design. To meet this requirement, all storage facilities had to be covered, 53 bag type dust collectors were applied throughout the plant, and materials handling equipment was designed to minimize dust and spillage.

Jan 1, 1979

By Brad Grothen, Lok Home

The choice of TBM type is never easy, but it becomes especially challenging when faced with a hard rock tunnel with expected high water flows and pressure. Slurry Shield tunneling has a long history of being used in these conditions to minimize the risk, though this method has brought with it other risks along with cost considerations. At recent projects around the world, another method has been proven to effectively manage these project risks without utilizing Slurry Shield tunneling: Shielded, NonContinuous Pressurized (NCP)-TBM tunneling in rock with a comprehensive grouting program. In this paper, the authors will analyze the use of Shielded NCP TBMs at projects around the world as compared with slurry shield tunneling in rock under water pressure. Recommendations will be given in order to establish a clear picture of the optimal tunneling method.

Jun 13, 2021

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES

Lithium-ion (Li-ion) battery pack fires pose great hazards to the safety and health of miners. A detailed experimental study has been conducted at the National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Mining Research Division (PMRD) to investigate the effectiveness of different fire suppression systems on Li-ion battery pack fire extinguishment. Tests were conducted in a well-ventilated container. Two sizes of battery packs (12 V and 24 V) were heated by heater strips to trigger thermal runaway and fire. Water mist with different flow rates, ABC powder, type D dry chemical, and water mist with F500 additives were used as the fire suppression agents. Multiple thermocouples were installed on the battery packs to measure the temperature evolution during the tests. The results indicate that the water mist with F500 additives is the most effective suppressant among the agents tested. Dry chemicals, however, do quench the fire for a moment, but cannot prevent re-ignition of the battery since they do not provide enough cooling. The findings of this paper can be used to develop safer battery fire suppression techniques in mining environments.

Jan 1, 2024

By III Feeley

The U.S. Department of Energy is supporting the engineering development of three advanced physical coal cleaning technologies--selective agglomeration, advanced flotation, and advanced cycloning--capable of significantly reducing the pyritic-sulfur content of U. S. coals. The objective of this activity is to provide the coal production and electric-utility industries with a cost-effective option for addressing the SO2 emission reductions required by the 1990 Clean Air Act Amendments. A secondary objective is to evaluate the potential of advanced coal cleaning for removing trace elements that are precursors to the formation of hazardous air pollutants. This paper will summarize the status of the three advanced physical coal cleaning engineering development projects.

Jan 1, 1993

By J. R. Iwinski

Escanaba, Michigan, is located on the South¬ern shore of the Upper Peninsula on a sheltered area of Lake Michigan called Little Bay de Noquet. The Chicago and North Western Transportation Company has operated a rail-to-ship ore transfer facility at this location for well over 100-years. It is the only terminal of its type on Take Michigan and thus can offer a longer navigation season to lower lake markets than other upper lake ports. It all started in 1864 when the Peninsula Railroad of Michigan, now a part of the C&NW, completed a 100 km rail line from Little Bay de Noquet to the Jackson Mines at Negnauee, Michigan. During that first year of operation approximately 31 000t of ore were loaded onto ships at Escanaba from what was then called the Merchants Dock. By 1871 demand had already exceeded capacity and it was necessary to build a larger dock, which in turn was replaced with a still larger pocket dock in 1903. There are no plans or records available to indicate how the ore was handled from rail to ship prior to the construction of the pocket dock.

Jan 1, 1981

By Jaime Lomelin

The brines from the sub-surface of the Laguna del Rey dry lake are pumped to Química del Rey, S. A. plant, where they are cooled in adiabatic crystallizers precipitating sodium sulphate decahydrate. This salt is dehydrated in multiple effect evaporators and dried in rotary kilns producing high purity anhydrous sodium sulphate. The spent brines from the sodium sulphate operation are concentrated in solar ponds, precipitating astrakanite and leaving a brine with a higher concentration of magnesium ions. This brine is treated with calcium chloride solution to eliminate the remainder of sulphates, leaving a solution of magnesium chloride ready for the manufacture of refractory grade magnesium oxide or periclase. The magnesium chloride is reacted with dolime to produce magnesium hidroxide which is washed, filtered, and calcined to produce soft burned magnesium oxide, which is briquetted and dead burned to produce the periclase.

Jan 1, 1984