Search Documents

By Deborah Muggli

Minera Escondida is the world's largest copper mine. Its capacity is more than 800 kt/a (880,000 stpy) of copper. The Escondida open-pit mine operates at an elevation of 3,100 m (10,170 ft). It is located in the Atacama desert about 160 km (100 miles) southeast of the port of Antofagasta. At Coloso, 14 km (8 miles) south of Antofagasta, copper concentrate is dewatered by filtration for storage and shipment to overseas markets (Fig. 1). Concentrate filtrate water, after being treated to remove suspended solids, is discharged at 60 m (200 ft) depth into the Pacific Ocean. This effluent is free of particulates. However, it does contain metal levels above US Environmental Protection Agency (EPA) receiving water criterion. EPA standards are more strict than Chilean receiving water guidelines. However, a multiport diffuser provides rapid mixing of sea water with effluent to ensure metal levels in the receiving water remain below EPA receiving water guidelines. The Escondida Mine began operation in December 1990 at a rated mill capacity of 35 kt/d (38,500 stpd). Since then, the complex has since undergone three expansions. In 1996, it processed 115 kt/d (127,000 stpd) of ore. At Coloso in 1993, about 25% of the copper concentrate was fed to an ammonia leach plant for solvent extraction and electrowinng of cathode copper. This plant is designed to produce 80 kt/a (88,000 st/year) of cathode copper. In 1995, the ocean diffuser system's capacity was doubled to accommodate increased flows to a maximum 50 L/sec (793 gpm). This was achieved by extending the diffuser chamber by 32 m (105 ft) and adding 16 nozzles, which doubled the diffuser's capacity. In November 1996, Rescan Environmental Services began a field verification of the outfall/diffuser system's performance. The study's objective was to determine the performance of the outfall/diffuser system by measuring dilution factors using fluorescent Rhodamine dye and to determine if copper concentrations are below the US Environmental Protection Agency (EPA) water quality criterion of 2.9 µg/L total copper (EPA, 1986). Rhodamine dye was injected into the outfall/diffuser system. An oceanographic survey using an in situ fluorometer was conducted to measure dye concentrations in the effluent plume. Water column characteristics were also measured. These included current speed and direction.

Jan 1, 1997

By Norman Weiss

The design of an ore-processing plant requires a high degree of cooperation among the geological, mining and metallurgical engineers. The purposes of this section are to provide mill design information most commonly needed by the mine planners and management, and to summarize the kinds of information that must be supplied to the mill designer to enable him to provide a suitable plant. 28.1-BASIS OF DESIGN NORMAN WEISS 28.1.1-SIZE OF PROJECT The size of the project generally is expressed in tons of ore milled per day, but company policies differ widely in this respect, a few adhering to this set figure but many expecting the design capacity to be liberal. To some companies that follow the latter practice a 25,000-tpd milling plant that cannot reach 30,000 or 35,000 tpd without major additions is a disappointment. The engineers responsible for planning the operation must know what is intended. Equally important are operating schedules, particularly the number of operating days per week and shifts per day for ore delivery, crushing, grinding and processing. Hours per shift also are an important factor in design, particularly in the case of ore delivery, and the percentage lost time expected for maintenance, cleanup, inspection, preventive maintenance shutdowns, and many others, has to be taken into account. Frequently, the ore deposit will vary in hardness and grade to such a degree that the capacity of the mill will vary widely from year to year and cannot be expressed as a fixed figure. but rather as an average over a calculable period, such as 10 yr, or as a specific daily capacity over the first 2 yr, next 4 yr, etc., or some similar projection. A good example of this kind of situation is Asarco's Mission operation 15 mi southwest of Tucson, Ariz., described by Weiss and Vincent.' where the major rock types differed widely in hardness, so that a change in the proportion of these types in the mill feed could have imposed difficult design problems if a constant tonnage rate had been expected. 28.1.2-EXPECTED LIFE The life of a mining operation depends upon the size of the deposit and the rate of mining. The latter is a policy decision based on an economic analysis which, in turn, is based on many factors.' From the point of view of mill planning, the estimated life of the operation determines many criteria and affects many decisions on strength of structures and degree of protection of men and materials, the quality of the materials-handling and process machinery, the type of delivery systems for ore to the mill and concentrates to the smelter or market, and many others. Costly installations that may be excellent investments for a 20-yr project may be wasteful for a 5-yr operation. An example is the comparison of different methods of crushing or grinding. Take single- vs. multiple-stage grinding-the former may be found more economical for a 5-yr operation, and the other, more costly, method more economical for a 15 to 20-vi- life.

Jan 1, 1973

By K. S. Narayanan, Marcia L. Bartges, K. S. Venkataraman

The starting powders' physicochemical properties and consistency are essential for technical ceramic products to meet their performance specifications. The need for finer and more consistent powders has opened new technologies for synthesizing powders from atoms and molecules. However, submicron and near-micron powders obtained from conventional comminution and classification techniques are still competitive. This paper shows several examples from electronic ceramic applications of how we can use powder characteristics for micromanaging by design the ceramic properties such as the green and fired densities, slurry rheology, shrinkage during sintering, and the microstructure of the sintered bodies. The cross-disciplinary nature of the technology requires that the researcher not only should have a firm grip on the fundamentals of one or more disciplines, but also should be generally aware of the intricacies of other disciplines as well.

Jan 1, 1992

By R. A. Basse, W. D. Diment, A. J. Petrina

INTRODUCTION In 1957, diamond drilling on a magnetic anomaly indicated an extensive zone of copper mineralization on what is now the Craigmont Mines property. By mid¬1958, drilling established a copper ore body. Milling commenced in September 1961 at 4536 t/d (5000 stpd) and by the end of October 1977 the mine had produced 339 662.04 t (374,363.9 st) of copper. At present, two-thirds of the mill feed is derived from underground operations and one-third from low-grade surface stockpiles. Craigmont Mines is situated 209 km (130 air miles) northeast of Vancouver (see Fig. 1), 16 km (10 miles) west of the town of Merritt, a logging, ranching, and mining community of about 7000 people. It is serviced by paved highways, Canadian Pacific Railway, British Columbia Hydro, and Inland Natural Gas Co. Water is pumped from the Nicola River, a distance of 6 km (4 miles) and a lift of 244 m (800 ft). In March 1967, the open pit mining operations at Craigmont Mines reached their economic limit and were suspended. Before this, it had been decided that a sub¬level caving method of underground mining would be used to supply ore to the concentrator after the cessation of open pit production. This chapter describes the fac¬tors influencing the choice of mining method, some of the problems encountered, mining practices, and results. GEOLOGY The ore bodies of upper Triassic age are located in a limy horizon striking east-west, closely paralleling the intrusive Guichon batholith, bounded on the south by rhyolites and on the north by graywackes, and dipping steeply to the south (Figs. 2a, b). The ore bodies are relatively narrow with a maxi¬mum width of 79 m (260 ft), a combined strike length of 853 m (2800 ft), and a vertical extent of 610 m (2000 ft). Chalcopyrite is virtually the only copper mineral, and 20% of the ore zone consists of acid solu¬ble magnetite and hematite. The area has been subjected to considerable faulting and brecciation, which is a major factor in the mining operation. Total geological reserves, at 0.7% Cu cutoff, for the deposit were 22 316 743 t (24,600,000 st) at 1.89% Cu. An additional 5 236 270 t (5,772,000 st) at 0.6% Cu were mined from the open pit. Ground Conditions The waste rocks-graywacke, andesites, and diorite -are relatively incompetent due to the high degree of fracturing and jointing, and all require varying degrees of support. The ore zones are somewhat less fractured; ground support is still required, however, although to a lesser extent than in the country rock. Ground conditions in the main ore body are better than in the smaller, nar¬rower ore bodies. Clayey fault gouge is present in most of the faults; gouge zones may be up to 6 or 9 m (20 or 30 ft) wide. The main ground problems are associated with local weakness rather than pressure. Shape of Ore Bodies (Figs. 2a, b and 3a, b) The main No. 1 ore body is approximately 244 m (800 ft) long and 46 m (150 ft) wide. It extends ver¬tically from the original top of the open pit at 4200 ele¬vation to just below the 3060 level. The No. 2 ore body is approximately 304 m (1000 ft) long, varies from stringer width at the extremities up to 79 m (260 ft) wide, and extends from 3060 level to 2400 level. Both these ore bodies have extensions re¬sulting in additional small irregular bodies. Ore bodies are mostly steep dipping, though part of the Wing ore body, an extension of No. 2 ore body, dips at 0.87 rad (50'). This ore body varies in size, but is approximately 122 m (400 ft) long, 21 m (70 ft) wide, and about 213 m (700 ft) high. No. 1 Limb ore body is a narrow extension of the No. I Main with a vertical extent of 137 m (450 ft), average width of 18 ft (60 ft), a strike length of 152 m (500 ft), and dips steeply at 1.4 rad (80°). No. 1 East is an eastern extension of the No. 1 Main with a vertical extent of 183 m (600 ft), a strike length of 91 m (300 ft), an average width of 30 m (100 ft), and dips at 1.2 to 1.4 rad (70 to 80°). No. 1 South is at the upper west end of the open pit with a vertical extent of 76 m (250 ft), a strike length

Jan 1, 1982

By David K. Parrish, Duane A. Labreche

Analyses of jointed, cracked, and fractured rock masses are needed in a variety of applications, including estimates of reduced elastic modulus for damaged rock, estimates of permeability changes as a function of stress changes, and estimates of relaxed regions due to excavation. A numerical model of a jointed rock mass, the compliant joint model, was used to study the response of a jointed rock mass near a circular excavation. The joint constitutive model was linear elastic in shear and nonlinear elastic in the relationship between normal stress and joint closure. Initial stresses were geostatic and representative of stresses in a granitic jointed rock mass approximately 300 m deep. The joint properties were based on values that are representative of joints in granite. The results from numerical simulations were compared with analytical results for stress near a circular opening in an elastic medium having reduced Young's Moduli to simulate jointing effects on the rock mass. The differences in response between the two models resulted from the differences in the symmetry of elastic properties, the shear modulus of the continua, and the constitutive relations in the two models. For example, the non- linear anisotropic elastic continuum described by the compliant joint model resulted in vertical stress concentrations near the side of the circular opening that were 25 percent higher than the vertical stress concentrations in an isotropic linear elastic medium. The equivalent Young's Moduli in the vertical and horizontal directions of the compliant joint continuum deviated by as much as 50 percent from the values assigned to the modeled region prior to excavations. The perturbations of the elastic Young's Moduli extended to distances of two to three radii from the opening.

Jan 1, 1986

By D. J. Hutchinson, S. Nickson

Cable bolts are used as a means of rock support around underground excavations in many mines across Canada and around the world. A substantial body of research on cable bolting was conducted at a number of Canadian universities and mines from the mid-1980s through the 1990s. Since then, research into selected areas of cable bolting practice has continued in Canada. The research has focussed on cable bolt instrumentation and on the inclusion of cable bolts in empirical stope design techniques. A review of cable bolting practice is now warranted at many mines. It has been five years since the completion of the previous substantial body of Canadian academic research and the associated advancement in understanding of cable bolt design, implementation and verification practice. Attempts were made at that time to transfer the new design procedures and performance assessment technologies to mine-site personnel. In some cases, this was effective, and ground control personnel continue to improve on their cable bolting practice at each specific mine site. However, at other sites, experienced people have moved on, and the new, less experienced personnel do not have access to the training or technical resources required to improve their understanding of the subject. In other cases, the technology was not transferred effectively to practitioners, with the result that substantial improvements can be made to the cable bolting practice at those mines. Guidelines for auditing cable bolting practice are provided in this paper. The guidelines include a discussion of the objectives of the audit, suggestions for audit procedure and a summary of the possible outcomes of a cable bolt audit. The objectives of an audit might include assessing the reasons for unexpected cable bolt failures, evaluating the quality of the installation procedures, quantifying the efficiency of the cable bolt system and assessing training requirements and procedures. A cable bolt audit should include consideration of all aspects of the cable bolting cycle, including the design, implementation and verification phases of the operation. At the end of the audit, a ranking should be assigned to the components of the cycle. The ranking system can then be used to identify items that require immediate attention, others that could be improved and others that are adequate. Following completion of a cable bolt audit, increased confidence in the support system and its application is generally, found, along with the potential for cost savings in many cases.

Jan 1, 2002

By Rock M. Poulin, Bruce G. Moulton, Daniel E. Nowak, David T. Cass

The Yacambu Irrigation Tunnel Project of 34 km, 5 meter diameter circular and horseshoe section, has been under construction since the early 1970's. Notable among the excavation challenges is high ground cover of 3,000m creating large lithostatic pressures in the tunnel alignment with subsequent plastic flow of the ground in the tunnel walls. The tunnel may converge from small amounts to 1 or more meters of diameter over long sections. Several excavation techniques have been attempted but all without desired results. The paper proposes a new machine concept that uses the history of ground experience as its basis for design.

Jan 1, 1995

By D. G. Ball

Other than being used to convey fill material for the gob stowage or building of ribside packs on advancing longwell faces, pneumatic conveying has not been used for the transport of materials on a large scale in mining operations. The technique is extensively used in the wood products industry for conveying wood chips, limestone and other ingredients for the manufacture of paper, for the transfer from railcars, barges or ships to silos or stockpiles and further transfer into the pulp mills. This method of material transfer has the distinct advantage of transporting suitable material over horizontal and vertical distances within the same system. In considering material associated with mining, this includes, ore, coal and rock up to 4 inch cubed size, throughputs of 200 tons per hour over horizontal distances of 3000 feet or vertical lifts of 2000 feet. In recent years tests have been carried out to determine the physical and economic limitations of pneumatic hoisting, the results of which have led to the installation of two fully productive coal hoisting systems at mines of the National Coal Board in Great Britain. The equipment used for the pneumatic hoisting of coal or waste rock is described in this paper, together with a brief history of the tests which led up to the installation of the two hoisting systems in Great Britain.

Jan 1, 1977

By Wen L. Chen

The steam coal quality is less stringent than metallurgical coal quality. The steam coal is prepared either by cleaning full size range of raw coal or cleaning coarse coal only, leaving the fine coal raw. The latter scheme is more cost competitive. It is particularly applicable to U.S. eastern soft coal where low ash coal is concentrated in fine sizes. For raw coal size separation, a recently developed Rotating Probability Screen, developed by the British Coal Board, may be advantageously used for easy change of raw coal separating size and to avoid screen deck plugging when handling wet and clayey raw coals.

Jan 1, 1983

By Ramamritham Sridhar, Vaikuntam I. Lakshmanan, Dan A. Macki

Historically, introducing new technology to the mining industry has been problematic. In general, the industry is reluctant to take risks with new technology because it is already heavily tied to risk, even using existing technology. Risk in the orebody itself can be substantial. The company is dependent on drill hole patterns that are expected to define what is underground, and process test work is often based on drill cores and other samples, which occasionally produce surprises. And even well-proven processing techniques can blindside the producer, resulting in embarrassing and costly difficulties. But if the industry is to grow in knowledge and become more efficient, new ideas must be introduced. How to introduce new technology is the essence of this paper.

Jan 1, 2001

By Corale L. Brierley

Bacteria have long been used for the extraction of copper during dump leaching of sulfide minerals and in the recovery of uranium from mined-out areas. However, bacteria can also be used in extraction of trace metals from copper ores and waste materials. Molybdenum, tungsten, nickel, cobalt, gold, silver, and other strategic metals can potentially be released from ores and wastes by biological processes. The chemistry and biology of these reactions, the potential for using the processes, and the state-of-the-art of the technology will be discussed.

Jan 1, 1983

By Wenhua Wan, Jan M. Mutmansky

Many concerns have been expressed worldwide regarding the use of diesel equipment in underground mines due to the potential health risks associated with diesel particulate matter (DPM). In assessing the risk to the health of miners and designing control strategies for DPM, it is important to know the concentration of DPM in the working areas of a mine. In some mines, significant stratification occurs due to the characteristics of the diesel exhaust, affecting exposure and the ability to measure DPM concentrations accurately. This study outlines some of the concentration profile data obtained during sampling at three mines where diesels were employed. Mine #1 (a gold mine) employed large openings in which a diesel-powered roof bolter was used. Mines #2 and #3 are both room-and-pillar operations with varying conditions. Mine #2 is an experimental mine where two stationary diesels were utilized for sampling purposes, while Mine #3 is a traditional evaporite operation using two mobile diesel vehicles for section haulage. These field studies indicated that some level of stratification occurred in all the mines, but the stratification was not as pronounced in the case of Mine #2 due to the complex pattern of exhaust emissions generated by the vehicles. The stratification seemed to depend on the distance from the vehicle, the mine air velocity, whether the vehicles were moving or stationary, and whether the exhaust was diluted by equipment design features. The concentration of DPM was generally higher at samplers located near the roof and lower at samplers located near the floor. However, this was not found in all cases. This paper provides conclusions on how knowledge of stratification patterns can be utilized in sampling and control of DPM in mine atmospheres.

Jan 1, 1997

By Thomas G. Hayes

Track-type tractors remain one of the most cost-efficient stripping tools available to coal miners. Whether they are "sweetening up" a dragline operation with prebenching or serving as the primary tool, dozers are important in driving down mining costs. This article reviews the application zone of track-type dozers. It also provides suggestions for site setup, equipping tractors and machine operation. In recent years, the track-type tractor has become more of a production tool in mining. With the advent of bigger machines, bulldozers have become a typical component in mining operations, removing overburden down to the top seam of coal. Large tractors can also be teamed up with draglines and other systems to maximize the effectiveness of the mining system. Bulldozers remain the tool of choice for topsoil removal, spoil reclamation or any application that demands low ground pressure, or short distance. The introduction of the 523-kW (700-hp) track-type tractor to the mining industry has made the bulldozer a low-cost-per-ton means of removing overburden. The large tractors offer enough productive capability to be considered prime stripping tools. And they can lower mining costs by complementing other mining systems (dragline, cast blasting and loader/truck). Four criteria determine whether a track-type tractor is the right machine for a particular application: ? Production requirements - dozer may fit job requirements better than a second dragline. [ ] ? Product support - availability of parts, service and technical expertise. ? Labor situation - how much of the cost per ton goes to the operator. ? Resale opportunity - recover a percentage of capital cost. Mining efficiency is economically controlling the cost of any system. Most operations rate the most economical means of moving material as cast blasting, dragline and the track-type tractor. All three of these systems share one common value: They are all sensitive to distance. Regardless of the application, all mining systems have an economic range. Exceeding this distance will affect cost and productivity.

Jan 1, 1997

By Gary A. Campbell, William A. Vogely

INTRODUCTION The theory of mineral demand often is slighted in the study of mineral economics. The supply side of the mineral industries usually commands a great deal more attention and effort by mineral economists than the demand side does because the study of mineral supply includes topics such as exploration, resource availability, and exhaustion theory that are generally considered unique to the mineral industries. Mineral demand, on the other hand, is thought of as being more general in nature and therefore of less concern to mineral industries specialists since it is similar to the demand for other inputs of production. This similarity with other inputs of production, however, does not negate the importance of a thorough understanding of mineral demand. It is the interaction of supply and demand that determines market behavior and not supply alone. Mineral demand is a key component among the factors that influence mineral production; there- fore, a good understanding of mineral demand can give one better insights into the industry behavior and trends than one would otherwise have. A strong working knowledge of the demand side of the mineral industries is a powerful tool for analyzing and predicting mineral market behavior. The material presented in this chapter does not depend on any special background in economics and should be accessible to all interested readers. The chapter is organized so as to permit an orderly progression of the basic topics of the theory of mineral demand while allowing digressions on related issues of special interest. The first section of the chapter is on the determinates of mineral demand. The discussion be- gins with the introduction of consumer demand and some of the necessary terminology of economics and proceeds to the particular case of the derived demand for an input of production such as minerals and the characteristics of such demand. The second section of the chapter is on the response of mineral demand to changes in economic variables like price and aggregate income. This second section of the chapter be- gins with a general presentation of elasticity of demand and continues with the particular case of the price responsiveness of mineral demand and its nature in the short and long-runs. A brief look at the response of mineral demand to price changes for other products is also included. The chapter concludes with a discussion on the effect of aggregate income changes on mineral demand and its nature in the short and long-runs.

Jan 1, 1985

By T. P. Smirnoff, R. J. Redmond, K .. N. Murthy

To minimize disruption to the Hollywood District of Los Angeles, a mined station using the New Austrian Tunneling Method (NATM) was developed. This paper presents the key factors contributing to the settlements and dynamic behavior of the unique binocular station design.

Jan 1, 1993

By Jan E. Stache

Commercial software programs are being utilized to create and maintain a mine subsidence database in conjunction with the U.S. Bureau of mines research on mine subsidence in Illinois. A three-year survey net of monitored structures in an Illinois subdivision was entered as textual information (attributes), on an existing AutoCAD drawing. These attributes can be optionally displayed on the corresponding drawing or extracted as a text file for import to a database program. The database program, dBASEIV, allows combinations of multiple database files for extensive querying capabilities. Subsurface database files can be merged with surface database files to enhance the effectiveness of surface response analyses in mine subsidence research. The geographic information system (GIS), pcARC/INFO, was chosen to integrate existing AutoCAD drawings and dBASEIV database files into a relational database with a graphical representation. The relational database allows users to update either the graphical representation or the database, with the changes being reflected automatically in its alternate format. The increased capacity, through use of a GIS, to query combinations of database files and have the results reflected graphically has significant potential for expediting mine subsidence research.

Jan 1, 1986

By Hans W. Brodbeck

The Advisory Conference on Tunnelling of the OECD, held in Washington, D.C. in June 1970, has established the following definition: "Tunnelling refers to the construction by any method of a covered cavity of predesigned geometry whose final location and use are under the surface, whose cross-sectional area is greater than 2 square metres". (1) The definition makes clear that the term includes all types of underground construction, be it in hard rock, soft ground, under mixed conditions, underwater, etc. Small-sized tunnels in rock therefore constitute but one part of the tunnelling scene. With an ever-growing urbanisation taking place in industrialized as well as developing countries, the demand for small-sized tunnels is, however, rapidly increasing and requires a far-reaching mechanization of excavation and support functions. This trend is accentuated by the fact that small-sized tunnels are far more labor-intensive than large ones, and, with wages raising at a much faster rate than costs for plant and equipment, this will accelerate the introduction of new tunnelling systems. SMALL-SIZED ROCK TUNNELS The main field of application for a tunnelling system for small sized hardrock bores is thus defined. It is in fact the numerous relatively short tunnels required under cities and other populated

Jan 1, 1974

By D. Burkhard, E. Herth

"Geologic structure and properties are the primary influences on ground control at San Juan Mine. Geotechnical properties of the coal seam and near seam strata, the presence of above seam sandstone paleochannels and water, are thought to be the leading contributors to ground control issues. It is the confluence of specific geologic conditions rather than isolated features that most often produce adverse conditions. Altering primary support installation and mining practices are done when unfavorable conditions appear during development. Installation of standing support is most often employed when adverse conditions develop at later dates. REGIONAL GEOLOGIC SETTING San Juan Mine is an underground coal mine located on the western flank of the San Juan Basin in northwest New Mexico. The San Juan Basin is contained within the south eastern region of the Colorado Plateau geographic province. The basin contains multiple coal bearing formations and is also a major producer of coalbed methane gas. San Juan Mine is stratigraphically located within the Fruitland Formation. From a prominent monocline marking the western boundary of the basin, the formation dips gently to the east towards the center of the basin. The primary driver for the deposition of coal bearing formations within the basin was the Cretaceous Inland Seaway. Multiple cycles of transgression and regression driven by sea level rise and tectonic subsidence deposited rock types from marine shale’s to terrestrial sandstones. The Sevier Mountains to the west of the seaway likely provided the sediment supply for the Fruitland Formation. During a major cycle of seaward regression, the Pictured Cliffs Sandstone Formation prograded over the marine Lewis Shale. The coal bearing Fruitland Formation followed, being deposited over the Pictured Cliffs. The Fruitland Formation contains numerous coal seams and is approximately 400 ft. thick at San Juan Mine. Fruitland Formation coal seams are numbered in order of superposition. San Juan mines the Fruitland number 8 seam. Dating has placed the age of the seam at approximately 73 to 75 million years [1]. LOCAL GEOLOGIC SETTING The Fruitland 8 coal seam dips approximately 1-3 degrees towards the E-NE. At San Juan Mine, the seam displays a mild plunging, synclinal structure, the axis roughly bisecting the mine from west to east. The number 8 seam consists of five coal benches and four volcanic ash band partings labeled sequentially based on superposition. The lowest portion of the seam is the 8-1 bench, the 8-2 through 8-5 benches following sequentially to the top of the minable seam. Ash band partings are labelled P1 through P4 from bottom to top respectively. The presence of distinctive partings and benches allows for seam definition and aids in identifying mining horizons."

Jan 1, 2016

By B. Hearn, Malcolm J. McPhersqn

Since 1993 Inco Ltd. has been using wet shotcrete at Stobie Mine. Through an evolving process the mine has reduced the thickness and fiber content of its steel fiber reinforced (sfr) shotcrete. However, the shotcrete support is used without any other type of ground support. A process referred to as bolt less shotcrete. Boltless shotcrete is used as the primary ground support method in development headings when the sub level caving front passes through the development drifts which now serve as migrating ore draw points. Although there are references of drifts and tunnels supported by shortcrete only, written accounts are rare. The empirical nature of most underground support designs makes them of limited value in a boltless environment. Considerable amounts of material testing and insitu trials have been completed in order to estimate material property strengths. Material testing, for adhesion, flexural strengths and compressive strength along with observational insitu data have been used to evaluate the performance of shotcrete. Punch tests on panels have also been undertaken in order to gain insights on the limitations of the two dimensional testing common to the laboratory. All these design aspects have been successfully utilized to design an efficient ground support process.

Jan 1, 1998

By R. Wu, R. Howell, J. Dase

Turquoise Ridge is an underground gold mine located in the Potosi Mining District, approximately 64 km northeast of Winnemucca, Nevada. Turquoise Ridge Underground is accessed via two shafts and a system of internal ramps and utilizes underhand drift and fill mining methods with cemented rockfill. The mine also employs mechanical mining as well as sill benching as mining methods. Ground conditions at Turquoise Ridge Underground are poor, and the Rock Mass Rating (RMR) may be less than 20, or very poor, in ore headings. Current production rate is 2,700 tonnes of ore per day. Key challenges in increasing production levels and reducing costs are the development of sufficient stoping areas and the transition from top-cut development to undercut stoping. Completion of the infrastructure development in the North Zone is necessary to achieve and optimize higher production levels. The #3 Shaft project is well underway and is expected to be commissioned in mid. 2022. The shaft will drastically decrease the haulage requirements in the North Zone

Mar 2, 2022