Search Documents

By T. A. Vivian

The use of heavy media organic solvents to recover coal from its attendant gangue is hardly new. DuPont built a pilot plant using pentachloroethane in 1936 at Weston Coal Company, Weston Breaker, Shenandoah, Pennsylvania. That's almost half a century ago. Since that time, it has become common practice to utilize similar classes of chemicals in laboratory separations of coal samples. It is the objective of this paper to discuss some specific separations on both pilot and laboratory scale on samples representing different classifications of coal. These separations have been carried out on coarse (+4 M), middling (4 x 20 M), and fine (-20 M) coal samples. The coal samples tested include Pennsylvania anthracite; Pennsylvania, Indiana and Colorado bituminous; Wyoming sub-bituminous; and Texas lignite. Other chlorinated solvents were used to vary the specific gravity of separation.

Jan 1, 1984

By Jun Ho Lee, Dae Young Kim, Ebrahim Farrokh, Ki Chang Hyun

"The Jinhae Geoje gas pipeline tunnel project is the largest (7.8 km) and the deepest (90 m) subsea tunnel in South Korea. This tunnel will house a pipeline to carry natural gas from the mainland to Geoje Island southeast of the country to alleviate the increased demands for natural gas, especially in the winter season. Tunneling is currently underway using two slurry shield TBMs of 3.5 m diameter. This paper describes the major design elements of the tunneling machines and their performance evaluation. For this purpose, a thorough analysis of geotechnical information was performed to evaluate the tunnel elevation to reduce the risk of tunneling under high water pressure in unstable and permeable rock mass under 9 bar water pressure. TBM specification and TBM performance were also analyzed using different methods, including well-known models as well as a rotary cutting machine test developed in house in Hyundai Engineering and Construction Company. INTRODUCTION High demand for natural gas, especially in winter season was the primary driving factor for the design of the Jinhae Geoje gas pipeline project. This project is located southeast of South Korea between Jinhae district and Geoje Island and runs for over 50 km length. The mid part of this project includes a 3.5 m diameter subsea tunnel consisting of two sections of Geoje to Jiri Island (4.3 km) and Jinhae to Jiri Island (3.5 km). Figure 1 shows the tunnel project location and its layout. Figure 2 shows the geological profile along the tunnel. As can be seen, the tunnel passes mainly through three rock types: granite, tuff breccia, and andesite tuff. This tunnel was planned to be constructed by two face pressurized shielded TBMs and to be lined with a segmental lining of 2.8 m internal diameter. The major challenge for this tunnel is its maximum expected water pressure at the tunnel invert (8.83 bar). At such a high water pressure, the TBMs required special design to ensure they can handle unexpected water pressure and to ensure the risks for the TBM maintenance intervention are minimal. In this regard, a thorough analysis was conducted on the TBM design parameters and geotechnical information to define required TBMs’ design parameters and to identify the safest tunnel elevation. This paper provides a brief overview of the project geotechnical information, TBM selection and its design specification, tunnel elevation selection, and TBM penetration rate evaluation. In this regard, a rotary cutting machine testing equipment was used to perform trial tests on a similar rock type encountered along the tunnel for performance evaluation and optimization."

Jan 1, 2016

By James J. Scott

To the safety engineer, mine planning engineer, and mine inspector associated with an underground operation, stability of the underground structure is of the utmost importance. In the United States in 1961 rock falls killed 167 miners, crippled many more, and cost the industry a fortune in lost equipment and production. Much research has been carried on to try to find ways to eliminate this loss of life and property. Within the past few years the interest in rock mechanics as a science has been at its highest point, Private industry, government agencies, universities and foundations have launched studies to gain a better basic understanding of the stability of underground openings.

Jan 1, 1966

By Richard Minnitt, Philippe Renard, Christina Dohm, Winfred Assibey-Bonsu, Matthew Aboagye, Julien Straubhaar, Mahlomola I. Mabala

The application of multiple point statistics (MPS) in oil studies has gained traction over the years; however, the use of MPS in mineral resource estimation and classification is still limited. This is despite MPS’ ability to deal with complex and heterogeneous geology better than the commonly applied two-point based methods. The availability and choice of a representative training image (TI) are often cited as the main challenge holding back MPS’ application in mining geostatistical studies. On the other hand, the general approach used in mining whereby early focus is on higher grade areas and lower grades are planned to be mined later presents a massive opportunity for the development of representative TIs. Mined-out areas provide large amounts of historical data that can be used to develop training images or training datasets that can be used to estimate in mining extension areas (often lower in grade), provided low grade areas are underpinned by similar geology analogue. This approach will enable more robust estimates in mine/pit extension areas for both high- and low-grade extensions than with traditional two-point geostatistical methods.

Jun 25, 2023

By Liu Hongkang, M. J. Virnig, Yang Xianwan, Zhu Yun

A new technology for recovery of gold from loaded carbon developed by Kunming Institute of Technology is introduced. The principle, production practice and results are described.

Jan 1, 1993

By M. Fig, A. Juganda, M. Zurhorst, J. Brune, C. Strebinger, G. Bogin

"Understanding the airflow patterns in and around the longwall panel can help to identify poorly ventilated areas that may be prone to methane accumulation. Ventilation network modeling provides quick simulation time, and flexibility in adjusting airway parameters and ventilation controls. Such modeling is effective for analyzing linear ventilation networks in underground mines, but cannot compute flows in caved areas of hard rock mines or longwall gobs. The use of Computational Fluid Dynamics (CFD) enables a more detailed investigation of the interaction between the airflows in these caved areas but requires much longer computational times, designing complex meshes and determination of a variety of modeling parameters. Airway friction factors and ventilation controls are simple to implement in a network model but can be difficult to model and adjust in CFD. This paper will focus on using mine ventilation network simulation to identify and analyze key parameters that are affecting airflow distribution in and around the longwall panels, prior to more detailed analysis with CFD modeling, using the example of a longwall coal mine. INTRODUCTION In longwall coal mine ventilation systems common in the U.S., the main purpose of bleeder ventilation is to dilute methane gas and prevent the formation of explosive gas mixtures in the caved, poorly ventilated gob areas and adjacent mine workings. In longwall operation, these critical areas include the development headings inby the longwall face, and the gob. Methane-air explosions in these areas may be ignited by spontaneous combustion, rock-on-rock friction and other sources. Although rare, ignitions due to rock-on-rock friction caused by roof falls caving into the longwall gob are possible and were suspected in the Willow Creek mine explosions in 1998 and 2000 (Elkins et al., 2001; McKinney et al., 2001). Rock-on-rock frictional ignitions are difficult to prevent, as they occur in inaccessible areas. Therefore, rendering the gob area inert is essential to prevent the formation of explosive mixtures. Research by Gilmore et al. (2015) and Brune et al. (2015) has shown that gob inertization can be a difficult or impossible when using bleeder systems, since the flow of gases through the gob depends on the gob permeability and the amount of fresh air leaking from the face and the immediate roof caving conditions cannot be controlled by the mine operator. Having the ability to predict the location where explosive gas zones (EGZs) form inside the gob will be helpful for designing the best ventilation setup to minimize explosion and fire risks."

Jan 1, 2018

By C. Patrick

Project scheduling is a deterministic technique utilizing single estimates of activity durations. In reality, activity durations are stochastic and can be better represented by probability distributions. This paper describes the development and utilization of a project scheduling simulation which combines analytical scheduling with stochastic activity durations. The purpose is to provide a method to analyze the sequencing of mining production processes and predict the effect of any planned changes. The simulation is demonstrated through realistic examples, such as longwall face-to-face transfer sequencing and the effect of varying advance rates on longwall development sections. Statistical data, to make more informed production decisions, are generated in the form of project activity/path criticality and project duration distributions.

Jan 1, 1995

By R. K. Mehta

Conventional triboelectrification based dry coal beneficiation methods require ground coal as a prerequisite feed material, energy intensive static-in-line mixer or cyclonic tribocharger configuration, and transport and/or improvement in the design of free-fall separators to improve the separation efficiency of [me pyrite/mineral matter from coal. The proposed paper illustrates the two concepts. First, the use of ceramic media in a polyurethane lined attitor in achieving simultaneous grinding and differential charging. Second, the use of an electrocentrifuge to selectively separate coal from mineral matter present in the triboelectrified mixture. It is of interest to note that some ceramic media can satisfy the requirements of both desired density and work function to achieve grinding and differential charging.

Jan 1, 1996

By John D. Smart, John W. Sager

The following paper is an evaluation of the instrumentation programs on recent Corps of Engineers tunneling projects. The authors have first-hand knowledge of the NORAD Cheyenne Mountain Complex (NCMC) Expansion Project. Information on the other projects comes from conversations with those directly involved in the instrumentation programs and from referenced reports. The specific objectives of this paper are: (1) to state the purposes of the instrumentation programs, (2) to discuss the benefits gained from the instrumentation, and (3) to present conclusions from this study that will provide guidance to those planning instrumentation on future projects. Presentation of detailed descriptions of the projects and instrumentation data is limited to that necessary to the accomplishment of the above objectives. NCMC EXPANSION PROJECT The NCMC is located at a depth of approximately 800 feet in Cheyenne Mountain near Colorado Springs, Colorado. For the current expansion project new chambers were mined to accommodate a new diesel power plant and associated cooling and air handling equipment. During 1971 some 55,000 yd3 of granite were mined through existing access tunnels for this expansion. A model of the new excavation is shown in Figure 1. The light shaded areas are new openings, and the dark areas are portions of the existing operating complex. The large chamber to the right is the power plant chamber and has a span of 67 ft, a height of 50 ft, and a length of 172 ft. The other large chamber on the lower level is the cooling tower chamber and has a span of 38 ft, a height of 45 ft and a length of 185 ft. The small chamber on the upper level has a span of 20 ft and is 27 ft high and 140 ft long. Other major excavations are the 18 ft diam air tunnel

Jan 1, 1997

By Subhash Sethi

The WIPP (Waste Isolation Pilot Plant) Project near Carlsbad, New Mexico. is a research and development project sponsored by the U.S. Department of Energy, designed to demonstrate the safe disposal of radioactive waste. A mine (repository) is being developed 2150 feet below the surface in a thick salt bed, which will serve as the disposal medium. The underground ventilation system for the WIPP project was originally designed based on a fixed project scope. The design criteria and ventilation requirements were developed for the performance of various activities as then envisioned towards the achievement of this goal. However, in light of new information and actual site-specific experience at WIPP leading to a clearer definition of the scope-related programs and activities, it was realized that the existing ventilation system may need to be modified. A re-assessment of the ventilation requirements--based on the current status of the facility and a clearer definition of the scope of the experimental programs, waste storage methodology, mine developmental activities. and current equipment list--indicates a two- fold increase in underground airflows from 210,000 cubic feet per minute (cfm) to 425,000 cfm. Various options to provide the increased airflow to the underground facility were considered and analyzed. Based on the techno-economic analysis, safety and environ- mental considerations, and other conditions unique to a facility like WIPP, it was decided to construct a new shaft to serve as the primary fresh air intake, along with the installation of additional fans in parallel with the existing set up. Low cost and the ease with which the new design could be implemented and integrated into the existing ventilation system with minimum impact on current activities and projected schedules were the guiding factors in designing the shaft and related ventilation modifications.

Jan 1, 1987

By Lyle W. Talbotr

The DeLamar Silver Mine is a Joint Venture between Earth Resources Company, the Canadian Superior Mining Company and the Superior Oil Company. The property is a consolidation of several old operations in the district. The more widely known are the DeLamar and Sommercamp Mines. The location is 20 miles northeast of Jordan Valley, Oregon and 55 miles southwest of Boise, Idaho. The mine is on the south slope of DeLamar Mountain in the Owyhee Mountains of southwest Idaho Initial interest started in 1969 with serious exploration beginning in 1970. The feasibility study was completed in 1974, and in 1975 Mountain States Engineers were retained to design and build the plant. Processing of ore began in March of 1977 with the first bullion poured in April of that year. The plant is currently processing some 2200 TPD of ore with a grade of four ounces of silver and 0.03 oz. of gold per ton of ore. Cyanide consumption is 2.5 lb/ton, zinc consumption of 0.3 lb/ton and flocculent consumption of 0.5 lb/ton. A flowsheet is shown as Figure I. The grinding circuit is of two stage design. The primary mill is an 18 ft. dia. by 9 ft. long semi-autogenous unit. The secondary mill is a 9 1/2 ft. dia. by 15 ft. long overflow ball mill. The mill discharges are combined and sent to 15 in. cyclones for classification. Cyclone overflow reports to leaching with the underflows reporting to the ball mill. The cyclone feed pump is an 8X6 metal case pump. The primary mill has 1000 installed horsepower and rotates at 68% of critical speed. The ball mill has 700 installed horsepower and rotates at 72% of critical speed. Because the primary mill is horsepower limited the ball charge is varied to maintain the desired throughput. The mill power is held at 980-990 HP by modifying the feed rate. Four inch forged steel balls are added any time the ore feed fails to reach 100 tons per hour for four hours. During periods of extremely hard ore, the ball charge has been as high as 14 v/o and at other times the mill has operated fully autogenous for weeks.

Jan 1, 1980

By D. E. Traut

A fluidized countercurrent ion-exchange system was developed, operated, and evaluated by the Bureau of Mines. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows are continuous except for short periods when resin increments are withdrawn. The exchange of uranyl sulfate between a simulated acid leach uranium solution and a strong-base, ion-exchange resin together with the subsequent elution with an acidified sodium chloride solution was studied. The effects of the number of sections, section heights, amount of resin withdrawal, and solution flow rates were investigated. Also examined were the kinetic and equilibrium relationships for the absorption step. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable. The column was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1975

By R. J. Piniazkiewicz

Talc orebodies are mined in Asia, Australia, Europe, North America, and South America. Operators in North America must be efficient quality suppliers to thrive in a talc market in which many overseas suppliers have advantages such as lower hourly wages, shorter distances to ports, and less government regulation and intervention. Continuous improvement through teamwork and innovation is needed in the following areas to thrive amidst worldwide competition: 1) Maximization of the in-place value of ore. 2) Research and development to yield new processes and products. 3) Safe productivity. 4) Involvement in legislative processes. 5) Wellness programs to lower health care costs.

Jan 1, 1993

By Y. B. He

The effect of the stability and rheological properties of magnetite dense medium on the separation performance of a 6" dense medium cyclone (DMC) is studied with the use of fine density tracers. The tests in which different size fractions of magnetite are used to prepare the dense media reveal that at low medium densities (<1.5 s.g.), the best separation is achieved when using the magnetite with intermediate particle sizes (du3.2=18 11m). At medium densities above 1.5 s.g., however, it is beneficial to use coarser magnetite. With the fine magnetite dense medium, an increase in medium density results in a decrease in separation efficiency. With the coarse magnetite, an opposite trend is observed; the separation efficiency is improved with increasing medium density. An accurate cutpoint control is critical in gravity separation. The cutpoint shift for coarse feed particles is found to decrease with increasing medium stability (density). It assumes values close to zero in a highly stable fine dense medium. When the size of the treated particles is small (<0.5 mm), the cutpoint shift is mainly determined by medium rheology. With increasing medium density, a continuous increase in cutpoint shift is observed.

Jan 1, 1993

By R. T. Swindeman

"INTRODUCTION This paper will discuss the topics in the recently released Conveyor Equipment Manufacturers Association’s (CEMA) Belt Conveyors for Bulk Materials, 7th edition, that deal with safety and maintenance. The most effective way to improve conveyor safety is through designing out hazards in the earliest stages of a project. When the safest way to perform maintenance is also the easiest, mechanics will naturally take the obvious and least hazardous approach. IMPORTANCE OF ACCESS Studies have shown that mechanics spend almost one-third of their time accessing the components to be serviced and approximately 25% of all fatal conveyor accidents occur during maintenance1. Chapter 2 of Belt Conveyors for Bulk Materials deals with design considerations. In Chapter 2 there are recommendations for access at the various sections of a typical conveyor for cleaning, inspection and maintenance. While, in some cases, providing access will increase the cost of the conveyor system there can be significant paybacks in reduced injuries, faster maintenance and easier cleaning. Piping and Conduit One of the significant recommendations in Chapter 2 for access is to restrict the mounting of piping and conduit to the conveyor structure in the Loading and Discharge zones of a conveyor. Piping and conduit are more permanent fixtures than maintainable components and should be located out of the way of components needing frequent maintenance. If electricians and pipe fitters are given convenient locations to make their runs they will natural use them. Flexible conduit and hoses can be used to connect to components from pipe racks and cable trays which further enhances maintenance. Access for Cleaning Another critical aspect of access is for cleaning. Approximately 33% of all fatal conveyor accidents occur while cleaning spillage and carryback under and around conveyors2. In the loading zone having sufficient height under the conveyor for cleaning increases the cleaning interval and allows for safer cleaning. In the discharge zone having adequate access for belt cleaning installation has a direct effect on the ability to install a proper cleaning system and perform maintenance."

Jan 1, 2015

By Paolo M. Brion, Z. Bade Sozer

"The Bypass Tunnel has high head conditions ranging from a minimum of 600 feet (183 m) under the Hudson River to a maximum of 875 feet (267 m) on the west side. The ground cover ranges from 425 feet to 900 feet (130 to 274 m). A two-pass lining is designed for the Bypass Tunnel. The bolted, gasketed precast segments carry the temporary hydrostatic and permanent ground loads. After the tunnel is put into service, the design assumes that the final lining, which varies from reinforced concrete to reinforced concrete with steel interliner, will carry the permanent hydrostatic loads. The design head for the segments is assumed at 775 feet (236 m), and the internal operating pressure head is around 1,200 feet (366 m). This paper discusses the design hydrostatic head and different load conditions considered for the segments, the load sharing between the segments and final lining, and the means employed to control water and hydrostatic pressure. PROJECT BACKGROUND The Rondout-West Branch Tunnel (RWBT), a segment of the Delaware Aqueduct, was built from 1937 to 1944 and provides about 50% of New York City’s total water supply. Monitoring and tunnel operations have shown that the RWBT is leaking up to 35 million gallons per day (MGD) (132.5 million L/day). In particular, two locations have been identified as areas of concern: Roseton and Wawarsing, as shown in Figure 1. The Wawarsing reach of the aqueduct will be repaired with an extensive grouting program when the RWBT is unwatered. However, because of the extensive nature of the leakage in the Roseton area, a Bypass Tunnel will be constructed to divert the flow around this area."

Jan 1, 2016

By T. M. Klemetti, T. J. Batchler, T. J. Matthews

How representative are partial-panel screen tests of the in situ response of screen to roof and rib deterioration and displacements? Can a more representative procedure that tests up to two full screen panels improve the utilization and effectiveness of screen as a roof and rib support? This paper details a new full-panel screen test procedure and the initial results. The full-panel test frame was designed to test a 2.4 by 3.6-meter screened area with bolt spacing as small as 0.3-meter increments. The initial design included up to 6 screen pull points, but additional locations can be added to produce a more uniform loading. The test frame was developed to capitalize on the capabilities of the Mine Roof Simulator (MRS) at the Pittsburgh Mining Research Division (PMRD) of the National Institute for Occupational Safety and Health (NIOSH). The initial tests included a baseline test of a partial panel (1.22 by 1.22-m screen section) using the original 1.52 by 1.52-meter test frame, a 1.22 by 1.22-meter screen section test in the new full-panel test frame, and two tests of 2.4 by 3.6-meter screened area in the full-panel test frame. The 1.22 by 1.22-meter screen section tests in the full-panel test frame produced a peak load 6% higher and a yield load 30% lower than the partial-panel (original) test frame. The multiple pull points of the full-panel frame produced variable yield, peak, and intermediate loads, but on average were lower than the single pull-point tests. INTRODUCTION Roof and rib surface support has become a major component of the stability and safety of underground coal openings in the past 15 years. The use of screen, either metal or synthetic, has proven to decrease the injuries of underground coal miners. By 2005, there were 466 injuries in the United States caused by roof skin failures, with numerous mines not employing roof screen. In contrast, in 2015 there were 175 injuries caused by roof skin failures, with at least some of the reduction due to the increased use of roof screen. A continued effort to increase the utilization of screen in areas of underground coal mines where workers are traveling and working can reduce these injuries even further. To aid in this effort, the testing of various screen types under various loading and attachment conditions is required. Past testing efforts have primarily consisted of partial-panel testing in a laboratory setting. Laboratory testing of roof screen, both metal and composite, has been conducted in several ways by researchers, manufacturers, and other entities. The primary focus on the testing has been evaluating weld integrity of 1.22 by 1.22-meter screen section tests of various screen types utilized in mining (Dolinar, 2006; Dolinar, 2009; Tannant, 2001). There have also been several efforts at numerical simulation of the screen and screen/rock interactions (Murali et al., 2006; Shan et al., 2014). A few full-panel tests were performed with one pull or loading point in the center of the screen panel (Shan et al., 2014). As most previous efforts have mentioned, the only true way to evaluate the capabilities of screen is to conduct full-panel testing. Single wire strand, weld, and partial-panel (1.22 x 1.22-m) tests as well as numerical modeling only provide insight into the actual response of full-panel screen. A new test frame and procedure have been developed at PMRD to conduct various loading, anchoring, and material testing.

Jan 1, 2019

By L. Rudolphy, P. Tähkiö

"The cPlant is a modular flotation plant which has been designed to minimize capital expenditure and risk. The plant is based on a number of standard modules, for both flotation and ancillary equipment, which can be configured to give the required flowsheet for the ore being treated. All of these modules can be rapidly deployed and erected onsite, minimizing not only engineering time and site preparation but reducing the time taken to get the plant up and generating revenue. Given the paradigm shift in flotation circuit design that has been employed in the cPlant it may allow smaller, previously uneconomic deposits to be exploited and create a more cost efficient upgrade route for existing plants. This paper introduces the cPlant and presents a case study comparing EPC cost and development timing of a cPlant against a traditional flotation circuit design. INTRODUCTION In the development of any mining project the cost associated with process plant engineering, equipment procurement and installation can affect the financial viability of a project. This is of special significance for smaller scale mining projects which perhaps don’t have the mine-life or revenue generation to justify the payback on a modern processing facility. Listening to customer feedback and understanding the challenges that small to mid-sized projects can face lead Outotec to the development of the cPlant. Modularization of mineral processing plants isn’t a new idea with a number of examples being reported in literature for gravity gold (Cabot, Trudel and Cabot, 2001; Gray et al., 2006), dense medium separation (September and Abate, 2006) and even hydrometallurgy (Saario et al., 2013). All these plants have been developed to try to improve on the traditional economics associated with fixed processing plants. Using standardized modules to construct a plant reduces engineering time and design costs which can both be beneficial to the outcome of a project. In addition the modular nature of the plant lends itself to transport to remote sites and rapid installation with only minimal site preparation required. A plant of modular design also has several other advantages over its conventional cousins. Firstly it is relatively easy to expand by duplicating existing modules. Secondly the modules can be treated as building blocks for the process and rearranged if a change in conditions requires flowsheet adjustment. Thirdly, there is potential to disassemble and remove the modular units at the end of the mine life. The ability to easily disassemble, re-pack and transport the plant to a new location not only is important to the long term environmental footprint of an operation but can also be seen as a bonus to an operator that has a number of small ore deposits. If applied in this way modular plants have the potential to create a whole new operating model for previously unviable ore deposits."

Jan 1, 2016

By Meng Wang

"In this study, multiple methods that include geological surveying, laboratory studies, and numerical modeling have been used to study the deformation characteristics of a “deep inclined rock roadway with weak planes” (DIRRWP). Failure of the DIRRWP was found to be triggered initially by the shearing of the rock near the weak plane. The movement of the failed rock resulted in reduced confinement of the deeper rocks, and causing the failure of the supporting units and the severe deformation of the surrounding rocks. Hence, it is concluded that DIRRWP stability is affected predominantly by rocks near the weak plane. Corresponding control strategies for DIRRWP deformation were proposed: (1) greater support intensity is necessary to maintain the stability of the whole DIRRWP; (2) additional support is needed for rocks near the weak plane to reduce the potential of failure; (3) to increase the bearing capacity of the floor strata, as the floor needs to be supported; and (4) a supplementary support technique should be considered for cases of large deformation. The case study presented here indicates that the proposed control strategies can significantly reduce the potential of failure in rocks near the weak plane, thus preventing severe deformation of the DIRRWP.INTRODUCTIONAs shallow seams are mined out, the cover depths in most Chinese coalmines have become increasingly greater. Deep cover in a coalmine is considered to occur when the cover depth exceeds 800 m (Sun, Chen, and Miao, 2018). The loading and failure behavior of rocks in a deep cover setting are quite different from those in a shallow cover setting owing to the increase in in-situ stress, temperature, and hyperosmosis (Lobanova, 2008; Zhang et al., 2013). For instance, experience shows that bulking and dilating deformation in deep roadways is much greater than that which occurs in shallow roadways (Hou and Yang, 2018; Zhang et al., 2016). In addition, anisotropic behavior and thickness deviation of coal measure rocks, combined with the appearance of weak planes (e.g., faults, joints, and coal cleats) in coal and/or rocks, can significantly affect the stability of an underground roadway (Ghazvinian et al., 2013; Sun, Chen, and Miao, 2018). The presence of weak planes can significantly complicate displacement and stress transmission in nearby rocks. Additionally, tensile, compressive, and/or shearing failure in rocks near weak planes can be easily caused by high in-situ stresses in deep roadways; such failures may lead to further severe deformation of the surrounding rocks, resulting in roof falls and rib spalling (Kamata and Mashimo 2001; Wu, Ohnishi, and Nishiyama, 2004). A typical failure of the so-called “deep inclined rock roadway with weak planes” (DIRRWP) is shown in Figure 1. Severe deformation can be found near the weak plane. In this study, a plane or thin layer of rock/coal parting that can significantly reduce the strength of the surrounding rocks—and thus affect roadway stability—is defined as the weak plane."

Jan 1, 2019

By N/A

finally, but not least, the staff of Vaal Reefs Chemical Laboratory for their assistance and patience with the introduction of a new technology,

Jan 1, 1991