Search Documents

By Dr. -Ing. Karlheinz Timtner

This paper deals with the complicated and often misunderstood relationship between torsional windup, load sharing and peak torques in conveyor backstops. The principals apply in low speed, intermediate speed or high speed applications. Once the controlling factors are understood, a reasonable approach to selection procedures can be achieved.

Jan 1, 1996

By L. B. Guo, S. S. Peng

A hybrid boundary element-finite element model was formulated to model roof-bolt reinforcement of roof strata with bedding planes. This model was used to analyze the stress distribution around a rectangular opening, with variables such as opening width-height ratio, number of bolts installed, number1 location of bedding planes, in-situ stresses, etc. The most critical areas are identified, and the number and length of roof bolt required are then determined. Two case examples are illustrated.

Jan 1, 1991

By Stephen H. E. Phillips, Michael J. Beus

A pneumatic impact breaker is used to fragment the rock at the shaft bottom, replacing the drill and blast cycle. A backhoe-type mucker removes the broken rock. The operators are in protective cabs below the bottom work deck in the shaft. Preliminary testing has been accomplished at underground and surface test sites in Arizona. Seven, approximately 6.4 m deep by 7.3 m-diameter (21 ft by 24 ft) test holes, (a total of 45 m (148 ft)), were recently excavated in various rock types, including jointed and massive quartz monzonite and rhyolite. An average advance rate of .4 m/hr (1.24 ft/hr) has been achieved. This includes breaking and mucking the rock. Further data is being sought from an in-shaft demonstration.

Jan 1, 1981

By R. L. Schmidt, Williamson. T. N.

INTRODUCTION This paper describes one of several research projects funded by the Advanced Research Projects Agency to extend the technology of rapid underground excavation. This study and field research effort are to investigate alternative means to determine rock and geological conditions in advance of a tunnel boring machine (TBM). Approximately 1 year of a planned 3-year program has resulted in the definition of three candidate drill systems. Hardware has been assembled to field test these candidates and testing has begun. The 3-year objective is to develop a single optimum prototype drill and test it in an active TBM operation. ACKNOWLEDGMENT This research was supported by the Advanced Research Projects Agency (ARPA) of the Department of Defense and was monitored by the Bureau of Mines under Contract No. H0210037. The authors and sponsoring agencies are indebted to the quarry operators in California, Virginia, and West Virginia who offered assistance including access to their properties.

Jan 1, 1997

By Donald S. Skufca

This chapter focuses attention on major factors pertaining to plant design and general arrangement of equipment. Considered are efficiency of operations, coordination of maintenance and repairs, plant testing of reagents and possible future plant expansions. The design and general arrangement of equipment considers accessibility for maintenance and isolation for repairs, minimum personnel for operations and cleanup, safe working conditions with minimum interruptions to operations. The constant introduction of new reagents requires eventual plant testing and the manner of isolating a “line” or part of the facilities to allow comparisons in the testing of new reagents is discussed. As technology improves and process changes occur, additional equipment or plant expansions are inevitable. Space for these eventualities must be considered while the general arrangement drawings are in the development stages.

Jan 1, 1986

By Armando Alatorre

The Republic of México is the world's largest producer of celestite/strontium carbonate and natural sodium sulfate. It is also a significant producer of flourspar, barite, graphite, sulfur, feldspar, salt and gypsum. New production may be brought on stream for borates, wollastonite, garnet, calcium carbonate and others. The country covers a geographic area of approximately 2 million square kilometers (760,000 square miles), and is divided into seven geological/geomorphological provinces. Less than 20 percent has been explored in detail for either nonmetallic or metallic minerals. This leaves large areas available for the discovery of world-class industrial mineral deposits. In addition to new deposits of those minerals currently being produced, there is exploration and development potential for borates, magnesite, rare earths, nepheline syenite, heavy mineral sands and numerous others.

Jan 1, 1995

By H. Nakazawa

Galvanic contact, occurring between electricall y conducting minerals in flotation pulps, may affect the nature of mineral surfaces and influence their floatabilities. Rest potential and galvanic current measurements were made on an electrode combination of pyrite and pyrrhotite under nitrogen, air and oxygen aeration conditions, and the results were correlated with their oxygen-consuming characteristics and flotation behaviors. The galvanic contact improved the floatability of pyrrhotite, but adversely affected that of pyrite. Auger electron spectroscopy, x-ray photoelectron spectroscopy and scanning electron microscopy indicated that the formation of hydroxide or oxide and sulfate species of iron on pyrrhotite decreased whereas that on pyrite increased when these minerals were held in contact. An electrochemical mechanism was proposed for the observed behaviors.

Jan 1, 1985

By M. C. Fuerstenau

Flotation data indicate that sulfonate and dodecylamine adsorb physically on Mn02 at ambient temperature. Oleate also adsorbs physically if the zero-point-of-charge of the Mn02 is sufficiently high. Chemisorption of oleate apparently occurs between pH 8 and 9, and this phenomenon is enhanced considerably at elevated temperature.

Jan 1, 1966

By J. E. Carr

A bewildering number of continuous thickeners and clarifiers are used in mineral industries and other heavy industries. General types are: 1. Conventional Thickeners (Fig. 1). 2. Thickeners with Flocculating Feedwells (Fig. 2). 3. Solids Contactors (Fig. 2). 4. Tray Thickeners (Fig. 3). 5. Lamellas (Fig. 4). 6. Conventional Thickeners with Lamellas 7. High Flow, Fluid Bed Thickeners (Fig. 5). These units must be adapted to varied applications. They must provide operating flexibility to meet process needs. Such factors multiply the decisions which must be made prior to the selection of a thickener. The seven types of thickeners listed above, with their variations, share design concepts which limit their application and which can be used to evaluate their performance. Some of these are listed: 1. Feed velocities must be limited and/or controlled. 2. Natural or reagent flocculation is necessary. 3. Horizontal settling area is the basis for capacity. 4. Overflow velocities must be limited and/or controlled. 5. A controlled underflow is necessary. Applying these needs to the basic process concepts is thickener selection. The basic function of a thickener in the minerals industry is the separation of a thickened sludge containing fine solids from water. To this primary separation function are frequently added others to give a list as follows:

Jan 1, 1977

An open pit production planning method for stage mining is presented in this paper. The method brings solutions to the four most important parameters in stage mining : 1) the number of stages, 2) the size and geometry of each stage pit, 3) the mining sequence of the benches in the stage pits, and 4) the time of transition from one stage to the next. The method can also simultaneously optimize the ultimate pit, mine life, and production rate in each stage.

Jan 1, 1996

The role of ZnSO4 in activation of sphalerite (ZnS) and deactivation of lead-activated sphalerite has been investigated. Adsorption of metallic ions at the solid-solution interface, electrokinetic results for sphalerite under different chemical conditions, and thermodynamic calculations were used to elucidate the mechanisms involved. It is shown that flotation response of sphalerite in absence of activators is rather weak and that adsorption of ethyl xanthate on the mineral mainly electrostatic in nature. Zinc sulfate is found to activate the mineral but only in a narrow acidic pH range. This is attributed to the increase of zeta potential as well as the possible increase in amount of negatively charged bulk precipitated zinc xanthate. Lead ions activate sphalerite in a wide pH range and the lead activated mineral assumes a flotation behavior similar to that of galena (PbS). However, addition of ZnSO4 depresses the lead-activated sphalerite by replacing lead ions at the mineral/solution interface.

Jan 1, 1999

By Ernest F. Giovannitti

A couple of years ago, one of the major television networks produced a series on the environment. One episode in the series dealt with the nation's solid waste problem and some of the research being done to solve it. It was interesting to listen to one researcher who was attempting to develop a glass that when broken would dissolve in water. It was said that using this glass would eliminate over 100 million tons of solid wastes each year. At first glance, it would appear that this research-effort would make a significant contribution to environmental pollution control; however, if one pauses to consider the water, he can see that this solution to the solid waste problem may well contribute to a water pollution problem. The dissolved material must either end up in our surface streams or be removed in waste treatment systems. Either alternative may have a more adverse effect on the environment than the original problem. With today's emphasis on the environment, it is important that the effects of our activities be studied in depth. Then, by properly planning the activity, the adverse effects can be minimized. The coal mining industry 100 years ago was in the same boat, as our glass maker, is today. Unfortunately, it too failed to consider all the effects of its activities and as a result, in Pennsylvania, there are over 5000 miles of streams adversely affected by coal mine drainage. The situation is improving, however, because mine operators are beginning to recognize and accept the methods for controlling coal mine drainage. The purpose of this paper is to discuss the measures for the control of coal mine drainage and to set forth the factors that affect these controls.

Jan 1, 1972

By Armando M. Lago

This paper reviews the postwar changes that have occurred in the expenditure and financial behavior of mineral corporations, and in particular the relative importance of factors that affect the industry's supply and demand for funds. This quantitative statistical investigation of factors affecting sources and uses of funds of mineral corporations is achieved through the formulation of a simultaneous equation model of sources and uses of funds. After a description of the study sample in Section I, the postwar cyclical and secular financial behavior of mineral corporations is analyzed in detail in Section II. Section III formulates an econometric model of mineral corporate financial behavior which is then estimated and reviewed in Section IV. Section V discusses policy issues regarding depletion allowances, investment tax credits, and industrial organization of the mineral sector. Finally, the optimum financial structure of mining firms is discussed in Section VI, which analyzes the effect of corporate financial structure on the mining corporations' average Cost of capital.

Jan 1, 1969

By Peter B. Lilly

I appreciate the opportunity to tell you something about Kerr-McGee's Galatia Mine in Southern Illinois. This new underground mine was a departure for us since our previous experience had been gained in large surface mines in Wyoming. Although we were new, we did have the corporate experience in the operation of deep uranium and potash mines in New Mexico and Wyoming, and an earlier underground coal mine in Southeast Oklahoma. In arriving at our final design, we evaluated numerous concepts and finally settled on a two seam mine sharing a single shaft and slope. The mine, in turn, would be supported by a heavy media processing plant designed to optimize the yield from either seam. Further, we wished to be able to keep the two seams separate so that we could sell either seam separately or in a blend. Due to the thickness of the coal, the practical area dedicated to the mine provided forty to fifty years operations at the selected mine capacities. It was important, therefore, that our design and selection of hardware and systems provide for long life and low maintenance in order to compete in today's competitive markets.

Jan 1, 1984

A chartered bus with about 30 attendees of the just completed 1998 SME Annual Meeting headed toward Green Cove Springs, FL, which the author had been told was located somewhere south of Jacksonville, FL. In conjunction with the meeting in Orlando, RGC (USA) Mineral Sands provided a tour of its facility. The author had worked with heavy minerals on a laboratory scale, performing the usual gravity and magnetic separations, but had never been to a heavy mineral mine and processing facility. Years ago as a metallurgist, the author once applied for a job in a heavy mineral operation in Florida -it may have been the same operation. After turning north on to Highway 95, the endless billboards promoting beach-front retirement communities proved the Atlantic ocean was just a few miles away (although the author never caught a glimpse of it). After another hour, the bus suddenly turned west and continued inland for about 65 km (40 miles). The thought occurred, "We are talking about beach sands, what are we doing heading away from the ocean?" As the bus continued inland, the author was struck by the flatness of the land and by the lakes, rivers and wetlands. He was also impressed by the many fine stands of pine and hardwoods. The office of RGC (USA) Mineral Sands is located about 16 km (10 miles) south of Green Cove Springs. Upon leaving the bus, members of the tour were greeted by Graeme Sloan, general manager, and Elliot Mallard, manager of mining. They provided some general information about the operation, including a slide show. RGC's Florida operation produces four concentrates: zircon (ZrSiO,), rutile (TiO,), ilmenite (FeTiO,) and leucoxene (an alteration product of ilmenite containing 67% to 70% TiO,). With a work force of about 170, the annual production of the above products is about 23,27, 45 and 14 kt (25,000 30,000 50,000 and 15,000 st), respectively. RGC also has other mineral sand operations, in addition to gold and base metal mines, mostly in Australia.

Jan 1, 1998

By Jouko Suominen

The basic development of various mining equipment has been strongly influenced by two objectives; improving economic results and safety aspects. Both of these factors contribute to increased requirements of mechanization and automation in different parts of mining processes. When we are limiting the discussion the crushing circuits, automation has two dimensions, one being the component automation, or intelligence, the other being automation of complete processes. Both of these subjects are closely tied up, the former being a condition for the latter. The key technologies of crushing automation are transducers, programmable logics and computer software. Also equipment technology continually faces new challenges, which result even in totally new product families. One example of this kind of development area the track-mounted, integrated crushing systems, where design criteria have been simple control, unmanned operation, and flexibility in changing requirements. This crushing system, or philosophy, offers excellent possibilities for new concepts in various underground and open pit applications, connected with automatic process control. Following presentation is a summary of aspects, of haw a crusher manufac¬turer sees the development of automa¬tion as an integral part of equipment technology and development.

Jan 1, 1989

In the mining industry and in new and expanding fields, such as electronics, nucleonics, and astronautics, a new type of manager has evolved. The name most generally used is project manager. His business is to create a product and the principal means through which he accomplishes this is project management. In this chapter, new information is the product of the project manager; as such the products, for which the computer methods described throughout this volume are designed, fall in the domain of project management. It has been the author's experience that project management is the management tool to effectively direct the information technology function within an organization. The purpose of this chapter is to describe project management and to identify and present a solution to the problems associated with project management in the development and application of computer methods in a minerals environment. Specifically, the problems to be addressed will center around: (1) recognition of the need for project management in terms of business-environmental factors and product characteristics, (2) formulation of a method of operation in terms of organization and implementation, and (3) application of project management to the minerals industry.

Jan 1, 1979

By R. E. Weeks, D. J. Millenacker

Utilization of true in situ technologies for mining copper in Arizona will involve a complex environmental permitting process. This process is a key factor in determining the feasibility, costs, and implementing time- frames required for development of this innovative mining method. The regulatory structure in Arizona is presently changing due to enactment of the Environmental Quality Act (EQA) of 1986 and development of new aquifer protection rules and regulations. The US Bureau of Mines has reviewed the comprehensive hydrogeologic characterization, ground water monitoring, mechanical integrity testing, well construction, contingency planning, and other regulatory elements that will serve as mechanisms to assure protection of ground water resources. The purpose of this paper is to inform the domestic copper industry of the significance of the new Arizona regulatory structure and its implications for prospective in situ operators.

Jan 1, 1987

By Edward C. Dowling

The advance of science and technology influences the modern economy in countless ways. Older industries must adapt to changes in the marketplace, while new industries are born by applying new technology to meet consumer needs. In light of declining head grades and increased unit costs in the US minerals industry, new technological developments in the production environment are paramount to maintaining a competitive footing in the international marketplace. Micro-engineering research provides the transition between the knowledge base and the application of new technology on the production level. Economic considerations The primary goal of technical development in the production environment is to reduce unit operating costs. Simply stated, this is accomplished by improving operating efficiencies and productivities on the production level. The goal of micro-engineering research in the production environment is to evaluate promising technologies and develop the criteria necessary to apply them in operations. As such, this process is the first step toward innovation and discovery. Generally, the micro-engineering research is followed by macro-engineering development. In the production environment, there are generally more development projects than can be accomplished in a timely manner. Usually, this is the result of financial and human resource limitations. Consequently, it is necessary to prioritize the work such that the most beneficial projects are accomplished first. By performing a discounted cash flow analysis and using benefit-cost ratios (for non-mutually exclusive alter¬natives) or net present value criteria (for mutually exclusive alternatives), the projects can be rated from best to worst. In this way, the financial and human resources can be best allocated to first complete those projects giving the highest returns before moving on to other activities. Moreover, this information is a prerequisite for management to justify additional financial or human resources.

Jan 1, 1992

By Bart Hogeweg

The development of deep sea mineral deposits creates a new horizon for the mining industry. In a field where mining technology meets deep-water offshore engineering, new challenges are faced to come to the successful exploitation of these deposits. With the absence of proven technology for the mining of these minerals, a ?technological green field? is entered. IHC Merwede (IHC), a global market leader in the dredging and wet mining industry, is on the frontline of these developments. MTI Holland, IHC Merwede?s research and development company, has undertaken a number research efforts focused on the successful development of technology for the mining of deep sea minerals. This paper highlights a number of these efforts and illustrates IHC?s continued dedication for the research and development of technology to enable the commercial mining of deep sea minerals.

Jan 1, 2008