Search Documents

By J. P. McDonnell, L. A. Beckett, K. Y. Hammy

Dangerously high stress areas can be controlled by proper mine planning and/or destressing. This paper reviews practical methods to detect and destress high-stress zones along coal faces. The US Bureau of Mines investigated stress-related burst problems and destressing efforts at a cooperating mine. Laboratory tests of the drilling yield method for high stress detection were conducted to determine the correlation between the volume of cuttings obtained and the magnitude of the applied stress. A three- dimemiom1 computer modeling program was used to evaluate the effectiveness of stress relief methods.

Jan 1, 1987

By S. Lin, Y. J. Wang

Based on systematic definitions of a generalized multiple fan ventilation system, the concepts of an augmented system, its solution curve and the operating points of the original system are introduced. The Quasi-Newton algorithm is applied in combination with the switching-parameter method to ensure a continuous search along an augmented-system solution curve and identify all the possible system operating points on it. Two example networks are analyzed to demonstrate those concepts and the application of the algorithm for identifying operating points of multiple fan ventilation systems.

Jan 1, 1994

By Carol Cox Russell

More than two thousand abandoned mines within the Animas watershed in Southwestern Colorado are being prioritized for remediation by the Animas River Stakeholders Group (ARSG). Phased collection and assessment of information progressed from large scale to site specific. Prioritization was based on existing or potential environmental impact and technical feasibility of remediation as measured by dissolved Cd, Cu, and/or Zn in the discharge; indicators of habitat degradation; aquatic life in streams; cumulative impacts at the point of compliance; cost effectiveness; treatiblity/feasibility; and cultural and historic preservation.

Jan 1, 2000

By Bob Gordon, Allen Furth, Dan Dobbels

A 4.8 m (16 ft) diameter hard rock tunnel was driven through granite bedrock to create the 1.7 kilometer (1.1 mile) long Hampton McCloy Retention Tunnel for the city of Richmond, Virginia. During the work the tunnel encountered narrow seams of partially decomposed granite that were not self supporting and could be dealt with using ribs and lagging. However, as the tunnel approached the receiving shaft, it encountered a large seam of highly decomposed rock, alluvial deposits and running sand which resulted in soil loss into the machine. As a result of this condition, a jet grouting program was quickly developed to allow the tunneling to continue. This paper will describe the manner in which jet grouting was used to solidify and stabilize the decomposed bedrock, alluvial soils, and running sand to allow the TBM to continue tunneling.

Jan 1, 2003

By I. Orisek

The methodology and results of a feasibility study of an Automatic Truck Dispatching (ATD) system in an actual open pit mining operation, are presented. Using mine cost data, an economic analysis confirms that capital and operating cost savings with ATD out-weigh the costs. Productivity improvement achievable with ATD is quantified with a computer simulation of truck haulage based on mine production and operational data.

Jan 1, 1986

By W. Wan

Diesel particulate matter (DPM) emitted from diesel engines is currently considered to be a health problem in underground mines. As a result, attempts have been made to control DPM both by reducing emission rates and by managing the DPM that gets into the mine atmosphere. This paper presents a method for modeling the generation, transfer and distribution of DPM in the mining sections through the use of a convection-based computer model so that controls for emitted DPM can be evaluated. A variety of ventilation strategies and diesel deployment schemes for room-and-pillar development sections were simulated to compare their effects on average DPM concentrations at several fixed and mobile personnel locations in the section. Input data for the model was gathered from actual diesel development sections and derived from experimental study results provided by other researchers. Studied using the model were ventilation schemes using vent tubing and brattice, exhaust location strategies on the vehicles, and the direction of ventilation at the feeder-breaker location. A summary of results from this study will be presented.

Jan 1, 1994

By J. E. Gebhardt, D. A. Rice, P. E. Richardson

An improved understanding of the significant role of electrochemical reactions in sulfide flotation has evolved in the past 20 years, This understanding has been accompanied by a corresponding increase in attempts to control the electrochemical potential of flotation pulps for monitoring and controlling sulfide flotation circuits to improve metallurgical performance. This paper discusses the basic electrochemistry of sulfide flotation and the use of electrochemical potential as a control parameter.

Jan 1, 1993

By Ihsan Berk Tulu, Mustafa Can Suner

The synthetic rock mass (SRM) approach is a relatively new method to study the mechanical behavior of rock masses. Recently, an SRM approach was established to estimate pillar strength from laboratory scale to in-situ dimension using the two-dimensional Universal Distinct Element Code (UDEC). In this study, the developed methodology is applied to the S-Pillar database to estimate pillar strength and failure mechanisms as a function of width-to-height ratio of the pillars. First, stone mine rocks are categorized into three as low-, medium-, and high-strength according to their uniaxial compressive strength (UCS). Later, laboratory-scale intact rocks are scaled-up to the average in-situ pillar dimensions by explicitly considering the naturally existing joint sets. It is found that the strength of the pillars with low-UCS are overestimated when compared to pillars with high-UCS. This observation is attributed to the high joint density of the pillars with high-UCS. After obtaining in-situ pillar strength, the width-to-height ratios of the pillar models varied from 0.5 to 2.0 to gain a robust understanding of pillar mechanical behavior. Tensile failure is found to govern the pillar behavior with the width-to-height ratio of 0.5 while the combination of tensile failure in rib elements and shear failure in the core

By D. Y. Geng

Longwall mining is a relatively new mining method in the United States. Early trials in the eastern and central coal fields were not successful, mainly because, among others, the face supports did not have sufficient capacity. It was not until in the late 1960's, when the high- capacity self-advancing powered supports became available, that longwall mining was successfully reintroduced. Since then the number of mines employing the longwall method has been steadily increasing. It has reached approximately 7.5% in 1981. Currently longwall mining is used mainly in the Appalachian coal field. The seam depth ranges from 150 to 2500 ft. but mostly between 300 and 1400 ft. The seam thickness ranges from 32 to 144 inches with the majority between 40 and 100 inches. Nearly all longwall mining are in flat or nearly flat seams extracting in single slice, although one inclined and one thick seam longwall mining have been either operated or initiated in Colorado.

Jan 1, 1983

By R. B. Taylor

The Esmeralda mine is located about three miles west of the town of Parral, in the State of Chihuahua, Northern Mexico, and about 400 miles south of El Paso, Texas. The area is serviced by the Interamerican Highway and a branch line of the National Railways of Mexico. The Parral district is quite typical of the semidesert of Northern Mexico, lying near the western margin of the Chihuahua basin and range province known in Mexico as the ?Mesa Central? In the immediate mine area, low rounded hills and rolling plans slope toward the Parral River. Surface elevation at the mine is 5,800 feet. The Esmeralda vein outcrops strongly, but was too low grade to be of interest to the Spaniards, The first claims were staked in 1897 and limited exploration work to a depth of 550 feet was carried out prior to 1912, at which time work was suspended. The Eagle-Picher Company acquired the property in 1944 and by surface diamond drilling outlined an orebody to a depth of 800 feet, Minas de Iguala, S. A, de C.V., one of Eagle-Picher?s totally owned subsidiary companies in Mexico, then unwatered the old workings, developed the mine, installed a modern differential flotation plant and started production lage in 1948. To the present, more than two and ahalf million tons of ore have been mined and milled producing lead and zinc concentrates.

Jan 1, 1958

By Y. M. Jiang, D. W. Park

Longwall faces can move at high advancing rates, but many geological variations can cause unexpected instabilities and production losses. The rapid movement makes it necessary to evaluate different geologic conditions in the rock mass as fast as possible to assess their effects on the longwall face and shields. It is believed that prompt awareness of geologic conditions is the key to preventing instability at a longwall face. This paper introduces the application of fuzzy set theory for characterizing and evaluating roof conditions. Real-time monitored data coupled with fuzzy set analysis provides valuable information, such as shield leg pressure, developing load on shields, intervals of periodic weighting and the ratio of developing loads during periodic to normal times.

Jan 1, 1998

By P. C. Thakur

In gassy coal mines, some methane drainage is essential for mine safety, but the ratio of total methane drained to total methane produced by the mine can vary from 10 to 70 percent. The volume of methane not captured is diluted by ventilation air and vented to the atmosphere. Since captured methane can be processed and sold, it makes sense to maximize methane drainage from coal mines. This paper describes ventilation and methane drainage schemes to achieve these goals.

Jan 1, 2003

By Joseph A. Kantor

Several wall rock porphyry or pyrometascmatic copper deposits occur within the metamorphosed Paleozoic formations along the northern and eastern flanks of the Little Dragoon Mountains. Rocks ranging in age from Precambrian to Recent occur in the area. The Tertiary age Texas Canyon Quartz Monzonite intruded the sedimentary section in the eastern half of the range metamorphosing the Paleozoic carbonate units to tactites composed of garnet, diopside, and tremolite. Copper, zinc, and molybdenum minerals deposited in sites which are structurally controlled and stratigraphically favorable. Because the deposits are covered by alluvium, the information on structure, alteration, and mineralization is based upon a study of the diamond drilling programs. The mineralized district can be divided into four areas: 1) The Johnson Camp copper-zinc deposits; 2) The Dragoon copper deposit; 3) The I-10 copper-molybdenum deposit; 4) The Strong & Harris copper-zinc deposit. On the southwest end of the range beneath alluvial cover, the Cretaceous Bisbee Group was thrust over Precambrian and Paleozoic formations. The Tertiary Texas Canyon Quartz Monzonite intruded and metamorphosed them. In the upper plate, the Cretaceous sediments near the intrusive were metamorphosed to metaquartzite and andalusite and sillimanite schists. In the lower plate the Martin and Horquilla formations were marbleized. The lower Abrigo was metamorphosed to epidote rich calc-silicate tactites and biotite hornfels. A composite geologic cross section, based upon diamond drilling,, through the Dragoon copper deposit is shown in Fig. 1. The geologic events which formed this deposit are: 1. A faulted section of Precambrian Pioneer formation and diabase and Cambrian Bolsa and Abrigo formations was thrust over Pennsylvanian Horquilla formation. The Dripping Spring quartzite if present, has not

Jan 1, 1977

By T. A. McAfoose

As one of the major suppliers of the chestnut Ridge energy center, Rochester and Pittsburgh Coal Company continues the search for more efficient haulage systems. This search is one that is essential in providing coal to the Keystone and Homer City power plants at the most economical cost. These two electrical generating plants located in west central Pennsylvania are part of the energy center which consists of four generating stations. Prior to the time the two stations were put on line, August, 1967 for Keystone and August, 1969 for Homer City, our company made the decision to rely on belt conveyors from the section to the surface to provide for continuous main line haulage. The proximity of these generating stations to proven reserves allow for minimal truck haulage and minemouth setups. With the addition of seven new mines, in the past ten years, revisions have been made on the original setup to interconnect the haulage of several mines to deliver the product by belt to the power plants.

Jan 1, 1979

By William C. Beebe, Russell E. Martin

An account of driving and concreting two 900 m railroad tunnels for the Denver and Rio Grande Western Railroad under emergency conditions. Details the importance of on-site decision making by the Owner in completing the project successfully in record time. A general description of the geology and construction methods. The Thistle Drainage Tunnel drained water impounded behind the Thistle slide and serves as permanent diversion of the Spanish Fork River and Thistle Creek around the slide area. The project involved 684 meters of 5 m horseshoe tunnel, a 5 m diameter raised shaft and 23,000 cm of cut excavation.

Jan 1, 1985

By E. P. Lunghofer

Silicon Carbide and Aluminum Oxide were two of the early forms of man-made abrasives often referred to as synthetic and were invented at the turn of the century. Edward G. Acheson invented Silicon Carbide in 1893 and Charles F. Jacobs filed a patent for the manufacture of fused alumina from bauxite in 1900. Jacobs' patent provided a method for tempering the alumina by reduction and fusion to a degree of hardness and toughness suitable for abrasive purposes. These two inventions are the basis of the synthetic abrasive industry today. Improvements have been made in the equipment used in the process, however the process itself remains basically the same. In 1904 A. C. Higgins observed that hot spots developed on the shell of the pot furnace used in the reduction of bauxite. He found that by spraying water on the hot spots they could be prevented and, in addition, they failed to return in the same place. Higgins reasoned that the cooling effect of the water caused the melt contacting the metal shell to freeze as an insulating autogenous refractory. This suggested that an improved furnace design could be obtained by using a metal shell which is continuously flooded with water on the exterior surface. Paradoxically, a furnace required to contain tons of molten Aluminun Oxide was thus constructed of nothing but a sheet steel shell with no refractory lining at all. A test of such an arrangement was tried by Higgins with considerable trepidation and was found to be extremely satisfactory.

Jan 1, 1985

By John A. Patterson

There are certain data handling techniques used by statisticans that can help one to calculate the size of an orebody and to develop some of the relationships between size, cutoff grade, average grade, mining cost, and profit. Knowing the relationships amongst these factors can help determine the most desirable operating conditions. A statistical technique that we will use is data grouping. This allows us to work with relatively few groups instead of many samples, If we were able to segregate the ore in an orebody into grade groups, add the amounts in each group, and plot the sums as a curve, we would get something like Figure 1. A smooth curve develops when the grade classes are small enough, otherwise a "stair step? histogram results. The area under the curve, being the sum of the tonnages in all of the grade classes, is proportional to the total number of tons in the orebody. If we take the data of a distribution such as Figure 1 and add the tonnages above a specific grade we have in effect a cutoff grade

Jan 1, 1958

By M. K. Larson, R. G. Wade

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying the time- dependent response of rock stressed along weakness planes. The objective is to improve mine safety by reducing the number of roof falls that cause injuries and fatalities to miners. Researchers conducted direct- shear tests on mudstone overcored from a coal mine roof. Results showed frictional strength weakens with displacement along the shearing planes. Results of direct-shear creep tests also showed time-dependent deformation. Test measurements were compared to classical analytical models. Results suggest that the risk of roof collapse may be decreased through layout and support design to reduce creep rates and thus slow progression toward failure.

Jan 1, 2002

By K. J. Stratford

The selection of a suitable mathematical function for the modelling of the partition curve for dense medium cyclones is discussed. Five alternative functional forms (based on three basic functions) are compared using data obtained in the course of an extensive experimental study of a 610mm dense medium cyclone. It is shown that, for adequately sampled tests, any of the functions may be used, although a function based on the Weibull distribution is shown to be most suitable. Where data are poor, all functional forms exhibit disadvantages, notably in terms of a reduction in precision of parameter estimation. This problem can be exacerbated by the complex numerical techniques required to estimate the parameters of a particular function. A set of ideal requirements for a performance function are presented.

Jan 1, 1986

By G. T. Adel, W. Z. Choi

A model describing size reduction and mineral liberation during grinding has been extended to include multiple classes of composite particles. The majority of the model parameters have been directly determined using computerized image processing equipment to analyze the products from batch grinding tests. A coarse-grained sphalerite ore from Tennessee, representing a nearly ideal binary mixture of sphulerite and dolomite, has been used to experimentally validate the model for the case of dry batch grinding. In all cases, excellent agreement has been observed between the model predictions and the experimental results.

Jan 1, 1988