Search Documents

By R. Krishna

The basic ventilation equation of power equal a constant times quantity to the power three (P=constant x quantity3) makes it an extremely costly palliative as a long term measure. Provision of increased airflow is also limited by maximum tolerable levels of air velocity, the effect upon respirable dust and, in case of coal mines, spontaneous combustion. The paper high lights amelioration measures for climatic improvements at a lower cost. The paper has also shown a method for monitoring air pollution using laser technology.

Jan 1, 1997

"A cationic surfactant, tetradecyl tributyl phosphonium chloride (TTPC), was first used as a collector. Flotation characteristics of muscovite using TTPC have been investigated through flotation tests. And dodecyl trimethyl ammonium chloride (DTAC) was tested for comparison. Their adsorption mechanisms on muscovite surface were clarified using zeta potential measurement, DFT calculation and molecular dynamics (MD). The flotation results indicate that the recovery of muscovite decreases when the pH increases in the presence of surfactants. When a maximum of recovery was reached, the dosage of TTPC was 2×10-5mol/L which was half of that of DTAC. Zeta potential measurements confirm that the TTPC displays a stronger collecting power than DTAC and is a superior collector for the muscovite flotation. DFT calculation and MD simulations show that TTPC interacts with the muscovite mainly through electrostatic attraction and hydrogen-bonding. The conclusions drawn from purely theoretical computations matched remarkably well with the experimental results. Keywords: Quaternary phosphonium salts; Flotation collectors; Flotation INTRODUCTION Muscovite mica is widespread in igneous, sedimentary and metamorphic rocks. It has the general composition KAl2(AlSi3O10)(OH)2. Muscovite mica exhibits perfect cleavage along the (001) plane, which exposes interlayer potassium ions[1-3]. In aqueous suspensions, the potassium ions readily enter into solution, leading to the development of a net negative charge on the (001) plane[4-6]. The surface of the muscovite mica is negatively charged at all pH > 1[7]. Due to the negative charge surface over the whole pH range of 2–12, the muscovite mica would not be expected to respond to anionic collectors in the absence of an activator. Conversely, the mineral is readily recovered using cationic collectors. However, until now, various amines and their derivatives (with N atoms as the center) are still the only available cationic collectors which still had their shortcomings such as weak selectivity, low flotation speed. Since few types of cationic collectors could be used, in some sense, the limitations of collectors are increasing significantly and the cationic flotation is facing more and more challenges. Quaternary phosphonium salts, as novel cationic surfactants, are widely used in antimicrobial, catalysis and surface modification field due to their biological activities, hydrogen bonding capability, stability and superior group electrical property[8-10]. There are a number of processes where quaternary phosphonium salt surfactants have shown better properties than quaternary ammonium salts and amines. Although the adsorption of quaternary phosphonium salt surfactants at the bacterium–liquid interface has been studied thoroughly, the case of adsorption in mineral surface has not been investigated thus far."

Jan 1, 2016

By Joseph R. Hatch

Previous studies of the Thompson and Temperly ore bodies show alteration aureoles in the Middle Ordovician host-rock limestones, dolomites and shales extending laterally as much as 60m from the ore. Thickness, texture, carbonate and clay mineralogy, major-, minor-, and trace-element contents; and carbonate carbon and carbonate oxygen Isotope compositions of the host rocks all have been significantly altered by hydrothermal processes. Organic geochemical analyses of samples from the basal 8-cm-thick carbonaceous shale bed and immediately overlying limestone bed of the Quimbys Mill Member of the Platteville Formation, collected from within the ore, the alteration aureole, and the unaltered country rock show: 1) solution of carbonates and residual concentration of organic matter, 2) decreases in the volatile (Si) and pyrolytic (S2) hydrocarbon yields In samples of the basal shale from within the ore, 3) decreases in the relative amounts of the lower molecular weight (<nC25) saturated hydrocarbons in samples from the ore, and 4) no changes in either the organic carbon isotope composition or the Rock-Eval or biomarker thermal maturation Indicators. In light of the 125-170°C depositional temperatures documented for the early marmatitic sphalerltes in these deposits by fluid Inclusion studies, the lack of thermal alteration of the organic matter suggests a relatively short mineralization episode, a conclusion supported by the relatively simple sphalerite band stratigraphy. The decreases in the volatile and pyrolytic hydrocarbon yields for shale samples from the ore supports a model for mineral deposition which obtains sulfide through reaction of brine sulfate and indigenous organic matter.

Jan 1, 2013

By D. W. McGlashan

[Comideha;tion o 4 chyakd- chem and aLtuctund phopetttiu o auRdide nm&, The in~o/uncction gained h ;to be uned ;to iM;tmph& ( I! dnukey bho hen mind-aundacu , ( 2 ) modidicakio~n 06 ;the minmd n~tdacu, and (3) eac;tiom at ;the mind adac fnom ;thu e baic din oipfina, concep;tc, wLth hegattd ;to .the changen kha;t awtgacu undehgu, heac;tiom kha;t might take place, ,the geom&y 04 ;the inkmduce, ;the nkde 04 diddmenk &om and iom in ;the intmdace, and okhm phyaicd and chemicd pttopemXu od an intmdace mun;t be developed, weighed and appfied. The au/tho~ ded wah thue concep;tud connidmatiom @om which hypokhuu me n& ko denchibe khe envhomenkd-ivttadaciae hela;tiomhipa doh nevmd nddide minettah, The ch&enge and moltivation in khe hu eattch h in a henhe a deattch doh baic dad and helcctiomkipa needed doh accompfi he&.] INTRODUCTION Qualitative and quantitative explanation of particulate solid separations are unknown entities because of the lack of adequate models and mathematical relationships to explain the activity occur- ring between the solid and liquid phases. It is a transitional region in which it is difficult to ascertain the mechanisms of adsorption of ions, molecules, etc. on mineral surfaces, as well as other secondary reactions which occur in interfacial regions. Thus, in this paper the authors deal with conceptual considerations from which hypotheses are set forth to describe the environmental- interfacial relationships for sulfide minerals.

Jan 1, 1968

By Stryker Magnuson

While probe drills are not strictly necessary for all projects, the incorporation and use of probe drills and pre-grouting adds capability and insurance to boring operations. Water ingress and unstable ground can be resolved before becoming a problem and resulting in costly delays through the use of enhanced, 360-degree probe drilling setups. To do this, proper design of the array of drill ports in the shield, matched to the possible ground conditions, is critical. For ground with exceptional water and instabilities expected, additional probing locations are low-cost additions that can lower risk and increase efficiency. In this paper we will look at recent and ongoing projects including the Lower Meramec Tunnel and Jefferson Barracks Phase 2. We will detail the design of those probe drill arrangements, and our overall recommendations for probing/grouting systems that best suit challenging ground conditions and keep projects running smoothly.

Jun 13, 2023

By QU Hong-lue, YANG Lin-han

Aiming at the subjective impact caused by subjective weighting method in the establishment of rockburst risk attribute identification and prediction model, the combined weighting method was introduced to eliminate the influence of unreasonable weight of each index. Eight discriminant indexes affecting the risk of rockburst were selected. Through the literature review, relevant rockburst cases were collected and 8 index rockburst sample sets were established. A variety of machine learning methods were used to analyze the feature importance of discriminant indexes in the samples, and then to determine the objective weight values of different methods. Combined with the subjective weights determined by the Analytic Hierarchy Process, the combination of weights were successively carried out. Based on the attribute recognition theory, the combination weights with different objective weight methods were established to identify the rockburst risk attributes, and verified by the confidence criterion. The results show that the objective weight value determined by the feature importance analysis of machine learning reduces the subjectivity of the weight of Analytic Hierarchy Process method, improves the prediction accuracy, and makes the prediction result closer to the fact.

Apr 26, 2022

By John N. Murphy, Edward F. Fries

The availability of fast, low-cost computer hardware and advanced software is opening new opportunities for minerals extraction and processing. Programmable Logic Controllers (PLC&apos;s) are currently used extensively in the minerals industries; this paper looks beyond PLC&apos;s and that vintage of “computer control”--it looks toward what the authors see as new in the next five years. Topics covered include expert systems, neural networks, intelligent signal processing, and hierarchical controllers as applied to mining and mineral processing operations.

Jan 1, 1993

By A. Mahtab, S. Xu, P. Grasso, B. J. Fu

The large population base, complex geology of the large land mass, and notable commercial activity have accelerated the development of underground construction market in China. The projected lengths of underground openings per year in the various sectors are: hydro-tunnels, 180 km; coal mine entries, 40 km; transport-tunnels, 300+ km. An example of the mega projects (being planned by the Government) is the water supply scheme for connecting Yangtze river to Yellow river involving 131 km of water tunnels with a diameter of 8-10m. Several large projects are highlighted in the paper with reference to the schemes for generating hydro-power, mining of coal and minerals, and constructing transportation networks. The related problems of construction and geomechanics are outlined.

Jan 1, 1995

By Edwin H. Bentzen

Talc, as a mineral, is rather widespread, but as an ore sultable for mining, it is rather limited. Materials sold as "talc" range from the impeccable white material from Italy to a gray-green-bluish material from Virginia. Some uses of the material called "talc" seem to be determined by the color of the material, some by the chemistry of the material, and some by the particle size of the ground material. But, there seems to be some overlapping of criteria used to judge the acceptability of a raw material. So then, any producer of talc material that is not a consumer of this raw material is faced with the age-old problems: "what do I call the stuff, and to whom should I try to sell it?" The answer to the first part is easy: if you want a high price, call it "talc"; if you want a low price, call it "soapstone". This may seem like a very simplified answer, but it is apparent that some of the products sold as "talc" have more than a minor amount of impurities in them; whereas, if they were called "soapstone", these same products would probably get a lower price.

Jan 1, 1973

By Richard R. Klimpel

INTRODUCTION Previous papers by this author have discussed some of the difficulties involved with optimizing the performance of industrial flotation circuits, e.g. Klimpel (1988, 1989). The two major problems seem to be: 1) the inherent "systems" nature of the froth flotation process which leads to a great deal of self-compensation among the various operating options available and 2) the inherent variations in mineralogy, water chemistry, etc. that always seem to be present in industrial operations. In particular, the influence of reagent dosage has been emphasized in the above referenced work including an industrial system interaction denoted as the R/K trade-off, Klimpel (1984, 1987). Using a simple two parameter model for fitting time - recovery data, Klimpel (1980): [ ] where r is cumulative recovery at time t or at the t th cell, R is the long-term equilibrium recovery and K is the first-order rate of mass removal from the cell (time ), the definition of the R/K trade-off with increasing reagent dosage can be given as follows: at low dosages both R and K increase, at intermediate dosages R continues to increase but K starts to level out, and at high dosages, R may flatten out or still continue to increase but K starts to decrease, sometimes rather quickly. An illustration of this effect in a batch laboratory flotation cell is given in Figure 1. The purpose of this paper is to give a detailed plant illustration of this R/K trade-off phenomena with changing collector dosage which shows just how highly interactive the grindinglflotation system in sulfide mineral processing really is. This is one of about 20 plant level case studies that are being presented and evaluated in an upcoming book, Klimpel (1990). The particular study given here was completed in late 1979 on a copper ore of head grade 0.93% Cu. The frother being used was Dowfroth* 250 at a constant dosage of 0.15 g for each ton of solids feed to the rougher bank and the slurry pH was 10.2. The motivation of the study was to better understand the relationship of changes in feed rate (hence in particle size and state of liberation) with variations in collector dosage (potassium amyl xanthate). The major concern was to determine how much extra economic benefit could be gained by better utilizing the existing grinding mills and rougher bank consisting of eight identical cells. The remainder of the flotation circuit was also studied, including regrinding of rougher tails, but did not prove as critical as the rougher bank operation itself. It appeared from an overall economic viewpoint, the battle was being won or lost in the manner in which the rougher bank was being operated. This was not to minimize the roles of the scavenging and cleaning circuits but those portions of this particular circuit could be rather obviously operated to achieve maximum benefit given the specific output of the rougher bank. A special attempt was made to maintain constant ore type throughout the entire test program. Eight specific test conditions were evaluated including three different feed rates (and hence three different size distributions) to flotation. Tables 1 and 2 summarize the eight test conditions and overall recovery results at the end of the rougher bank for each test. A single test consisted of at least three consecutive eight-hour shifts operating at steady-state with composite cell lip samples taken over the final eight-hour shift. "Trademark of The Dow Chemical Company

Jan 1, 1990

By X. Meng

A kinetic model for batch leaching of various metals with different lixiviants has been developed. Overall material balances for reactants and products at the solid/liquid interface were formulated with various types of heterogeneous reactions in place at the interface. The solutions to these mass balances have been identified analytically as well as numerically using a Runge-Kutta method. Applications of these numerical solutions to various leaching systems using the rotating disc or powders have been discussed. Examples of the metal dissolution systems considered in this study include cobalt, nickel, copper and gold in acid, cyanide or ammoniacal solutions.

Jan 1, 1994

By Seanley C. Suboleski

This paper examines the likely productivity improvements that have resulted from the introduction of technological advances in underground coal mining during the decade from 1977 to 1987. Included in these advances are the changes in longwall mining; the introduction of larger, more reliable, more repairable continuous miners and shuttle cars; the introduction of remote control and flooded-bed scrubbers; supersections; and other improvements. Procedural improvements are also examined and quantified, the unexplained gains in productivity are attributed to??other factors", among them an increasing maturity of the work force, stabilization of the mining laws, increased labor-management co-operation, and economic urgency.

Jan 1, 1990

By Theodore M. Olson

The Washington State Highway Department consists of seven geographic dis¬tricts. District offices are located in Seattle, Wenatchee, Olympia, Vancouver, Yakima, Spokane and Bellevue. District is covered from the Spokane office, and is responsible for the six counties in the northeast corner of the state (Fig.l). It is bordered on the north by the International Boundary, on the south by the Snake River, on the east by the Washington - Idaho border, and on the west by a north-south line thru Lake Roosevelt. The landslides to be discussed in this paper are at Colfax, Washington, which is located in the southeast corner of the district. The town of Colfax is situated in a narrow valley eroded into the Tertiary volcanic basalts by the Delouse River. The valley walls are steep and generally colluvium mantled. State Highway 1°c, from Spokane to Colfax, descends into the valley from just north of Colfax on a bench cut into the valley wall. The highway department designed a widening project to increase the misting two lane roadway to three lanes, thus providing a passing lane for uphill traffic. The third lane was constructed as a cut section for the entire length. Construction excavation was begun at the top of the hill in silts of eolian origin. Proceeding downhill, excavation encountered three individual basalt flows with two zones of palagonite tuff separating them. The upper palagonite zone was dry, and excavation proceeded across this zone with no mishaps. The lower palagonite zone carried considerable groundwater. As excavation crossed the lower zone landsliding became contemporaneous with excavation, due to removal of toe of slope and saturated conditions. Remedial measures for landsliding consisted of designing shot rock buttresses across the palagonite zone and also the installation of horizontal drains to reduce hydrostatic pressure.

Jan 1, 1971

By M. D. Chatham

Revolutionary electronic monitoring and control systems provide a gold mine of diagnostic and prognostic information. Lower cost per ton results from timely operator action, increased visibility of information to production and maintenance personnel, and better fleet management. When information is effectively integrated into fleet management systems lower costs result from higher availability, longer component life and reduced repair cost. This paper will present the objectives of the Caterpillar Vital Information Management System (VIMS) and provide actual examples of successful use.

Jan 1, 1995

By Waldo Valderrama, Luis Magne, Paola Grandela

The effect of liner shape on power consumption was studied in a small laboratory mill under various operating conditions. It was found that the angle subtended between the lifter front face and the face in contact with the mill case has the most significant influence. The increasing height of lifter reduced power consumption, whereas the lifter spacing did not show any influence. The effect of height is less relevant at lower front angles. Highest power consumption is achieved with a 45" front angle. A comparison of cylinders and balls under identical conditions gives higher power consumption for ball charges. The data does suggest that, for maximum power draw, slip in the outer layers of the charge and the early recirculation of energy to the mill case should be avoided. Both factors prevent an efficient energy transfer to the mill charge.

Jan 1, 1995

A panel discussion on carbon-in-pulp processing of gold and silver ores was one of the highlights of the 1981 AIME Annual Meeting in Chicago. The session generated considerable interest and discussion among panelists and the audience. For those unable to attend the panel, the program was recorded and the discussion appears in this two-part report. The panel was co-chaired by Robert S. Shoemaker, vice president of San Francisco Mining Associates, and Laurence D. Hartzog, principal engineer with Bechtel Civil and Minerals Inc., San Francisco, CA. Panel members included: George Potter, consultant, Tucson, AZ; Kenneth B. Hall, metallurgical superintendent, Homestake Mining Co., Lead, SD; and Donald M. Duncan, resident manager, Pinson Mining Co., Winnemucca, NV. There have been several types of carbon-in-pulp adsorption vessels in use, such as the Dorr-type agitator, the simple propeller agitated tank, the Pachuca tank, and, lately, the draft tube-type of agitated tank. Which one of these is best and why? Potter: On the selection of the most appropriate adsorption vessel, there is a considerable difference of opinion that stems largely from the fact that every ore is different. The mesh of grind, the pulp solids, and the apparent viscosity of the pulp as caused by its clay content and chemical conditions all differ. The traditional Dorr agitator with the slow speed center sweep and either peripheral or center column air lifts has worked quite well on the finer grinds of all minus 65 and probably 70-80% minus 200 mesh. Pachuca tanks have also been successful and they may be capable of handling a coarser feed than the traditional Dorr tank. One uranium mill, for example, handles minus 28 mesh sandstone ore in a Pachuca. The most recent development and one that commands consideration is the draft tube agitator in which there is a turbine which closely fits inside a draft tube. Velocity in the tube is carefully calculated to avoid undue shear and thus abrasion of the carbon. The objective in all cases, of course, is to mix the granular carbon, which is typically 6 x 16 mesh, very gently but thoroughly in a slurry with minimum carbon abrasion. I do not know that there is one outstanding choice just yet and I have been unable so far to get information on C-I-P service for ore grinds as coarse as 35 mesh. Duncan: The major advantage of draft tube-type is the ease of startup. At the Pinson plant we installed draft tube-type agitators but it is too early to quote experience with them. We also haven&apos;t operated long enough to determine just what our carbon loss is. The advantage, of course, in the draft tube design is that it requires only about one-third the horsepower input of a conventional agitator. If it has no other advantages, it has that. Hall: The type of vessel most suitable for C-I-P adsorption depends on the type of ore treated and the prevailing operating conditions. In most cases, a deep tank with turbine-type mechanical agitator and low speed tip velocities would be satisfactory. Turbine-type impellers give a positive type of agitation which assures optimum ion contact and reduces short circuiting. Thorough aeration is possible with an air sparge properly located. A mechanical agitator can easily be started up after an outage, but it is usually necessary to drain and wash out a Dorr rake-type or Pachuca before restarting. The turbine-type impeller requires more power, but maintenance costs are negligible if rubber covered impellers are used. Carbon losses are minimal. In smaller plants, Pachuca type agitators provide adequate aeration and agitation. Bob Polak, Occidental Minerals (from the floor): Mr. Hall, you favor the mechanical-type agitator with the preface that the proper design is critical. Could you elaborate on this for us? Hall: The most important thing is low tip speed to prevent carbon attrition. I think the impeller should be sized so that you get a good sweeping action toward the bottom of the tank, across its bottom, up the sides, and back to the center. The advantage of the draft tube is that you get a more positive agitation and you probably get improved aeration too. Polak: Do you know of anyone using an upflow mechanical agitator rather than a downflow unit? Hall: I think that Bob Wilson at Custom Equipment has designed one where he has located the sparge directly beneath the impeller. The air bubbles are broken up by the impeller as the slurry passes through it. The slurry flows upward, outward, down the sides, and, again, back to the center of the tank. I don&apos;t know that any tanks of this design are in commercial use. Hans Von Michaelis, Randol International (from the floor): A question to any of the panelists on flat bottom versus conical bottom Pachucas. Hall: I would say the conical bottom would be most suitable in most cases. Some plants have experienced problems with flat bottom Pachucas in that they have a tendency to sand in on the sides of the tank so only the center of the tank is active. Duncan: With our draft tube tank we placed an inverted cone in the center of the tank bottom and blanked off the bottom comer around the circumference of the tank to facilitate movement of the pulp. Other than that, as far as conical bottom tanks are concerned, I&apos;m generally opposed to them because of the cost and height differential. Larry Kramer, Kennecott Minerals Co. (from the floor): Mr. Duncan, you mentioned that the draft tube-type could be agitated with about one-third the horse-power applied to a conventional propellor agitated tank. I have trouble trying to pin down that kind of number. Could you give a bit of rationale as to why that mechanism has a lower horsepower requirement? Duncan: I think it has to do with the fact that below the propeller you have straightening vanes. The pulp, which is flowing vertically downward, is turned and flows upward again without any recirculation. You have an inherently less horse-power requirement in that type of tank. The one-third horsepower requirement is a number I obtained from Lightnin, which supplied us with details of the draft tube. There is probably much more recirculation with a conventional impeller type that is wasted motion. Potter: Last week I saw some agitators in South Africa with short draft tubes and actual turbine-type impellers. This plant was handling 200 kt of ore per month. The tanks were flat bottomed, and the agitation appeared to be quite satisfactory.

Jan 8, 1981

By S. Lin

Fan stall is a notorious phenomenon with axial-flow fans. When multiple fans of this type serve a ventilation system, their mutual impacts are very complicated and not well understood. Results from laboratory experiments indicated that the immediate consequence of a fan working across its stall zone (i.e., the pronounced trough on the fan characteristic curve) is that some branches in the system may suffer abrupt and even drastic changes in air quantity and pressure. The quantity range of the fan that causes the abrupt change is called an unstable operating range. The corresponding quantity range of a branch is called a non-achievable quantity range of the branch because any quantity within this range cannot be achieved without changing some parameters of the ventilation system (e.g., branch resistances). These concepts are introduced based on the test results from tubing networks to bring attention to these important characteristics of ventilation systems.

Jan 1, 1996

By J. A. Pagliero, R. T. Quiroz, S. H. Castro

Selected voltammograms in tetraborate buffer solutions in the presence of ethyl xanthate or isopropyl xanthate at pH 9.3, for chalcocite, covellite, chalcopyrite, and enargite mineral electrodes, are presented. The concept of critical Eh of dixanthogen condensation (Ehc) is introduced, and the line of Ehc is thermodynamically defined in plots of log [X i] vs Eh, for methyl, ethyl, propyl, and butyl xanthates. A reaction scheme of xanthate oxidation in four steps, involving the dixanthogen condensation step, is proposed. A first attempt to interpret mineral flotation from a more general point of view is made. The electrochemical mechanism of dixanthogen formation and condensation is considered as a particular case of a more general and relevant phenomenon, which is the decomposition of the collector giving hydrophobic colloidal forms, whose associative behavior in bulk solution and at the mineral/solution interface is governed by colloid chemistry.

Jan 1, 1989

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Nucleation and growth of copper on 316L stainless steel from synthetic acidified copper sulfate was studied in the absence and presence of chloride ions and/or organic additives (HydroStar® 4208, DXG®-F7, Cyquest® N-900) using a potentiostatic technique. The current-time data obtained at 0.16V vs. SHE was analyzed using nucleation and growth models. Scanning electron microscope (SEM) images of deposits produced at 300 A m-2 show that the addition of 20 mg/L chloride ions increased the size and reduced the number of copper nuclei. Potentiostatic current-time data from the electrolyte without organic additives indicate progressive nucleation with two-dimensional (2-D) growth under diffusion control. SEM images obtained confirmed progressive nucleation with 2-D growth. 20 mg/L Cl- and 2.5 mg/L organic additives did not change the nucleation and growth mechanism, however the additives increased the number and reduced the size of copper nuclei leading to more uniform coverage of the stainless steel substrate.INTRODUCTION Electrowinning of copper is an important process in the manufacture of high purity copper metal. It is approximated that 20% of the world’s refined copper is produced from acidified copper sulfate solutions by electrowinning (Schlesinger, Sole, and Davenport, 2011). In many plants, copper is electrodeposited on AISI 316L stainless steel substrates for a period of 6-7 days, after which the copper is stripped from the blanks. Even though the deposition time for a commercial copper electrowinning circuit is around one week, it is critically important to control the nucleation, growth, and nature of the initial deposit (Sun and O&apos;Keefe, 1992). Deposit morphology and structure are influenced by the real current density at the electrode surface. The real current density across the cathode surface is made uniform by proper design of the electrowinning cell and electrodes and careful operational practice. Even with good design and control, some current maldistribution occurs. The outcome of severe current maldistribution is poor deposits that affect product quality and/or increase energy consumption. To combat current maldistribution and create a larger operating window in terms of current density, temperature, and copper concentration, small amounts of organic smoothing agents (traditionally guar products) are added to copper electrowinning electrolytes. Moreover, these additives inhibit the growth of copper dendrites, which leads to improved deposit quality by producing bright, smooth, and dense cathodes."

Jan 1, 2015

By Alberto Sarmentero

Venezuela, once a world&apos;s top gold producer until 1886 Witwatersrand discovery, did let fall its role then because of a serious lack of infrastructure and population, and lately (since World war II times), because of discouraging mining and taxation laws, laying upon an oil prizes bonanza. Recent research leading to estimates of about 5.000 mt. of gold, mainly related to the greenstone belts of the Guiana Precambrian shield outcropping in Venezuela, are opening the scope for both Government and international investing and mining companies, for gold exploration and development projects in the country. This paper overviews Venezuelan Gold mining industry, as seen from the point of view of a participating mining company.

Jan 1, 1989