Search Documents

By W. C. Morgan

Recently passed federal strip mining legislation officially emphasizes that the increased coal production required by this country through surface mining is going to be obtained only with stricter environmental standards. Dozing overburden down the hillside in Appalachian contour mining or leaving drag1ine spoils in area mining is now taboo and it is now or will soon be necessary to return the disturbed land to as good or better condition than before mining. These new restrictions will create a need for new and better ways to do the job. This paper describes one approach for utilizing scrapers and dozers to strip all of the overburden and to replace that overburden in an environmentally satisfactory fashion. The objective was to do this at a lower cost than that possible with the traditional dragline system using dozers and scrapers for reclamation and topsoil handling. In area stripping, the dragline has been able to move overburden at an extremely low cost. Operating costs of 8-13¢/bcy are typical in many operations where rehandling is not required. However, the cost of leveling the spoil piles and rehandling topsoil add considerably to the low basic cost of drag1ine stripping.

Jan 1, 1977

By T. M. Campoy, J. R. Jones

When extending the life of an existing mine in Appalachia, it is common to acquire the adjacent reserves and extend the existing mine into it. The existing mine is often renovated to accommodate the new conditions. The existing mining system and the track and belt haulage systems may he modified while the new property is integrated into the old one. All of these changes create new constraints for the mine ventilation system (MVS) that require proper planning and control procedures. This paper presents a study that was carried out for the ventilation system of a newly expanded underground coal mine in the Appalachian region. The process of correcting the ventilation system of the existing mine is discussed. That is followed by a discussion of some of the stages of controlling the expanded system. Numerical data for these steps are also presented.

Jan 1, 1994

By Håkan Stille, Jalaeddin Y. Rafi, Fredrik Johansson

"INTRODUCTIONIn tunneling projects, pre-grouting is performed with the purpose of establishing an impervious zone around the tunnel periphery. This is obtained by reducing the penetrability of the most conductive fractures in the rock mass. The main attention, besides economy of the project, is given to limiting the ingress of water into the tunnel to a certain amount during construction s well as operation period. Failure in pre-grouting process may, according to Bruce (2007), significantly affect the project in terms of safety, performance, cost and time. In this respect, determination of design parameters (pumping pressure, properties of the mix and stop criteria) affects these projects significantly. In current practices, depends on the geological conditions and requirements of the project these parameters differ widely. Weaver (1991) recommends selection of design parameters, specifically grout injection pressures, based on site specific factors and the conditions at each specific hole into which grout is to be injected (grout hole logging and water pressure test data). Houlsby (1990) correlated the allowable grouting pressure to the quality of the rock mass and the rock cover above the grouted fracture. In his methodology, grouting should be continued until the maximum pressure was attained. Later, Lombardi and Deere (1993) introduced the Grout Intensity Number (GIN), which limits the combination of injection pressure and injected grout volume in order to control the energy induced in the fracture i.e. avoid fracture jacking. Even though the GIN method was a step forward in understanding of the mechanism of the fracture deformation, there are ambiguities connected to this methodology, thus determination of the intensity number is challenging (see e.g., Rafi and Stille 2015)a.A main problem when no theoretical solution is practiced is that effects from the chosen injection pressure, such as possible increases of transmissivity and changes in total grouting time, remains hidden in the overall grouting process. The question is if a high or a low pressure should be used to fulfil the requirements of the projects at the lowest possible cost."

Jan 1, 2016

By Gerald L. Dollinger, Joseph A. Roby, David Krauter, Kenneth Deering

Three high performance TBM's equipped with large diameter (483mm) disc cutters are currently operating in Norway. This paper summarizes the design philosophy, field performance and ongoing technical development of these cutters. Included are discussions of the early problems encountered with their usage and the solutions to these problems that have been developed. Also included are discussions of the penetration rates and cutter usages observed. From this data it is concluded that high performance TBM's with large diameter cutters can produce significant improvements in both overall performance and in cutter costs under hard rock conditions.

Jan 1, 1991

By R. H. Olson

Pigments are used in two segments of papermaking, as the major component in paper coating formulations and, in small percentages, as fillers in the paper web. Historically, the dominant use has been in coating, however, recent developments have fostered a multifaceted effort to substantially increase the pigment component in the paper furnish. Factors responsible for these developments together with their relationship to recent and forecast changes in papermaking technology are reviewed. Finally, some thoughts are presented on the probable timing and extent of these changes as well as their expected impact on the future demand for the common paper pigments.

Jan 1, 1985

By Emanuele Catelli, Paolo Vicentini, Manuel Petitat, Paolo Lanfranchi

"More than 800 million tons of material will be excavated during large underground projects such as tunnels, undergrounds and power plants by 2030 in Europe only. The raw material excavated is often classified as waste, which involves environmental impact and transport issues: landfill areas, CO2 emissions and noise. But how can such massive amounts of material be transported, processed and deposited? Using the example of the AlpTransit Ceneri Base Tunnel (15.4 km), we show that suitable excavated materials can be used sustainably as a primary resource for tunnel concrete. This requires careful planning of the installations and storage areas by the client, timely building of the processing plants and other handling facilities outside the tunnel and a continuous evaluation of the raw material quality. 1. INTRODUCTION Spoil management is a central element of large construction projects. The systematic reuse of suitable excavated material not only saves natural resources, reduces transport distances and landfill volume, but can also decrease overall construction costs. Ideally, all of the concrete needed for tunnel lining can be produced with this on-site material. Such a natural resource management concept was applied for the construction of the new Gotthard Base Tunnel (L = 57 km). Spoil management concepts are, how-ever, difficult to implement and call for innovative techniques, sophisticated logistics and organization. In the context of large projects, environmentally friendly transport, processing and storage of millions of tons of excavated loose material represent another logistics challenge (Simmen & Lieb, 2010). This paper shows key factors that led to the successful completion of spoil management at the Ceneri Base Tunnel, which constitutes a part of the AlpTransit Gotthard Project (Figure 1)."

Jan 1, 2016

By D. Hodouin

The improvement of mineral processing data using material balance computer programs is nowadays a current practice in many plants, engineering companies or research centers. It now becomes more obvious that such programs should integrate new features such as the preprocessing of data, the estimation of less accessible process variables and an in-depth interpretation of: the computed results. A few solutions to these new problems are already available. The feasibility of a mass balance computation for instance can be examined by analyzing the degree of redundancy of the measurements prior to any data adjustment. New variables such as chemical analyses in particle size intervals or liquid phase composition can be included in a set of measurements. Finally, a sensitivity analysis can be used to analyze the reliability of the results, to detect eventual outliers or to redesign a sampling scheme. Some illustrations of these new developments are presented.

Jan 1, 1989

By L. Adler

When systematically compared to other engineering fields, mining engineering is distinctive in 1) having a total systems concern. 2) dealing with encumbered space and 3) requiring full spectrum practice. The total systems concern results from having to design and then co-ordinate in space and time several major systems: excavating and bulk handling, ground control, life support and normal support. This requirement favors a generalist rather than a specialist approach. In coping with encumbered space especially in underground coal mining, the uncertainties of geologic conditions are compounded by tightness, roughness, remoteness and hazards. Into this difficult setting the total systems * complex is "stuffed," adding congestion and interference. Because of significant ground deterioration a flexible "rapid in-out" approach is usually vital to mining. Full spectrum practice arises from the need to manage, as well as to plan and design, a labor intensive operation. Since market conditions can also fluctuate most aspects of administration are needed in many respects, mining engineering functions relative to civil engineering in a way similar to industrial to mechanical engineering, with encumbered space being crucial. On this basis stress is placed on: 1) personal relations, 2) field work and 3) entrepreneurship, viewing time as money. Specific recommendations for improving engineering, safety and management and leadership are made. Since most new deposits are marginal, by applying these recommendations with high technology they could possibly now be mined on a widespread basis.

Jan 1, 1985

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"There are three distinct producing iron ranges in Minnesota, the Vermilion, Mesabi and Cuyuna. In trend the Vermilion and Mesabi are approximately parallel (E.N.E. and W.S.W.) and about fifteen to twenty miles apart. The Vermilion lies farthest north, near the. Canadian boundary. It is from seventy-five to eighty miles due north of Duluth. The length of its productive part is about twenty miles.The Mesabi Range is from fifty to seventy-five miles north and northwest of Duluth. Its length along the strike is about 110 miles, and the length of its present productive area about eighty miles. The Cuyuna range lies southwest of Duluth nearly ninety miles, and is the last of the Lake Superior iron ranges to be developed. The relative positions of the ranges are shown on an accompanying map. The Mesabi Range is by far the largest producer and contains the largest ore reserves of the three. The Cuyuna is next in quantity of proven ore, and in production since 1916, while the Vermilion is first in average quality of ore.On the west, both Vermilion and Mesabi ranges disappear beneath heavy glacial drift; and on the east, extend into Canada, the so-called Gunflint range near the international boundary being an eastward continuation of the Mesabi formation. This latter range is of no economic importance, however, at present. The exploration and development of the Cuyuna range has proved up a considerable tonnage of manganiferous iron ore, besides ordinary merchantable iron ore."

Jan 1, 1920

By P. T. Bissert, T. J. Lutz, J. A. Yonkey, G. T. Homce

"Underground refuge alternatives (RAs) require an air source to supply breathable air to the occupants. This requires pressure relief valves (PRVs) to prevent unsafe pressures from building up within the RA. The Mine Safety and Health Administration (MSHA) mandates that PRVs prevent pressure from exceeding 1.25 kPa (0.18 psi or 5 in H2O), or as specified by the manufacturer, above mine atmospheric pressure when a fan or compressor is used for the air supply. Research to date by the National Institute for Occupational Safety and Health (NIOSH) suggests that the design and implementation of PRVs used in RAs has not yet had sufficient performance analysis or technical development. In response to this need, NIOSH tested a variety of PRVs using an instrumented test fixture consisting of data acquisition equipment, a centrifugal blower, ductwork, and various sensors to determine if subject PRVs meet the MSHA requirement. Relief pressures and flow characteristics including opening pressure and flow rate were measured for five different PRVs under a variety of conditions. Subject PRVs included two off-the-shelf modified check valves, two check valves used in MSHA-approved built-in-place (BIP) RAs, and a commercially available valve that was designed for a steel RA and is currently being used in some BIP RAs. The test results showed relief pressures ranging from 0.20 to 1.53 kPa (0.8 to 6.1 in H2O) and flow rates up to 19.3 m3/min (683 SCFM). INTRODUCTION The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and mine safety standards enforcement [1]. Section 13 of the MINER Act specifically directed NIOSH to provide for research into the effectiveness and viability of refuge alternatives (RAs) for underground coal mines. This mandate culminated in the 2009 adoption of changes to 30 CFR mining health and safety regulations, requiring underground coal mines to provide mine emergency RAs and associated components, to provide a life-sustaining environment for persons trapped underground. Such RAs can be either self-contained mobile units or built-in-place (BIP) facilities. The regulatory changes also include provisions establishing requirements for Mine Safety and Health Administration (MSHA) approval of RAs and their components, and among these provisions are numerous criteria for providing a safe breathable atmosphere under positive pressure within the RAs. One specific criterion for maintaining a safe RA atmosphere requires the inclusion of an air pressure relief valve that will activate at a maximum of 1.25 kPa (0.18 psi or 5.0 in. H2O), or at a pressure above mine atmospheric pressure in the RA as specified by the manufacturer when the breathable air is supplied by a fan or compressor [2]."

Jan 1, 2017

By Vytas Svalbonas

Sophisticated computer analysis methods such as finite elements, finite differences, and numerical integration have become tools in the mineral processing industry for design of large mill shells. While use of such methods allows the analyst-designer to take new freedoms with his designed structure, there are also pitfalls and dangers which must be recognized for the proper use of such sophisticated tools. One of the worst of these is treating any computer answers as "gospel truth". The present paper discusses the knowledge required by the analyst-designer for proper use of computer analysis, as well as explaining to the layman how to identify questionable areas in such structural analyses.

Jan 1, 1979

By Alessandro Navarra, Aldo Quelopana

For decades, open-pit mine planning algorithms have incorporated geological uncertainty and other elements or characteristics for increasingly realistic representations. Among these complexities is the detailing of downstream processes that occur inside processing plants. Previous studies have demonstrated that the strategic mine plan and mineral concentrator design are coupled, and should therefore be optimized simultaneously within the same quantitative framework. However, existing frameworks offer limited representation of operational modes. This work demonstrates an approach to resolving this gap, in an optimization based on a parallelized Variable Neighborhood Descent (VND). The resulting algorithm embeds mass-balancing linear programming (LP) using a DantzigWolfe decomposition. A case study of a Zn-Pb deposit is presented to show the performance reached.

Jun 25, 2023

By N. Moony

The benefit of gravity separation in improving total gold recovery in grinding circuits has been outlined in a significant number of papers to date. However, the use of batch centrifugal concentrators (BCC) as an industry standard to extract gold has limited the potential for maximizing gravity recoveries -particularly in coarse gold deposits. This is a reflection of the high upgrade ratios obtained by BCC's which has an inverse relationship with recoveries. Survey work in Australia has indicated that installation of the InLine Pressure Jig as an alternative to the Bee will significantly increase recoveries of gold by gravity and, accordingly, increase total gold recoveries and lower operating costs.

Jan 1, 1998

By T. W. Camm

"As engineers, we are trained to use logical, rational problem solving to insure our mines operate at maximum efficiency. We tend to use the same technical approach to design safety into all mining systems. This works well for machines, but not so much for the human component. Recent insights in the field of behavioral economics provide useful ideas for addressing the fact that we are driven by emotions more often than by rational thought. Understanding the nonrational aspect of human behavior is an important piece of any safety system design. INTRODUCTION The most common economic model is based on humans making rational decisions; that given the proper information, we will make a logical, rational decision based on what is best for ourselves (Ariely, 2009, p. xviii). In many cases this is an accurate description of how we make decisions. As an engineer, I was trained to apply the precision of mathematics and logic to solve problems. As an engineering professor, I now teach this approach to bright young minds preparing them for a life of professional effectiveness as practicing engineers. That said, we are not only rational. Daniel Kahneman, winner of the Nobel Prize in Economics, describes a model for how we think (Kahneman, 2011). System 1 is the part of our mind that is fast, intuitive, and emotional; while our logical, slower, and deliberative mind is System 2. According to Kahneman’s model, System 1 runs automatically, most of what you think and do originates in System 1. System 2 takes over when things get difficult, including the application of math and logic, and the resolution (or avoidance) of conflict. As engineers, we would typically assume that we operate in System 2 mode most of the time. This is where the model becomes useful, for Kahneman points out two important aspects of the dynamic between the two systems in our mind. First, System 1 has biases, systematic errors that lead to answering questions with an easier answer (rather than a right answer) before System 2 is engaged. Second, we can be blind to the obvious, and also be blind to our blindness. Complicating things further, System 1 cannot be turned off (Kahneman, pp. 24-25)."

Jan 1, 2015

By L. M. Nuelle

Rare earth element (REE)-and gold-bearing breccia pipes are a potentially significant economic target in the Pea Ridge iron ore mine, Washington County, Missouri. The Pea Ridge deposit is one of eight known volcanic-hosted iron ore deposits in the Middle Proterozoic St. Francois terrane, which are similar to the Olympic Dam-type deposits of Australia. The iron orebody is steeply dipping, tabular-shaped, and cuts across the host rhyolite. The footwall of the deposit is zoned from the massive apatite-bearing magnetite core outward to heterolithic breccia, pseudobreccia, specular hematite zone, to an extensive silicified zone. The hanging wall is zoned from the massive magnetite core outward to a heterolithic breccia, pseudobreccia, and an amphibole skarn zone. The REE-rich breccia pipes cut through the various lithologies along the footwall at or near contacts. They are typically 60 m long, 15 m wide, and extend at least 120 m vertically. The pipes are comprised of fragments of rhyolite host rock, massive magnetite zone, specular hematite zone, and silicified zone rocks supported in a matrix of rock flour, barite, feldspar, monazite, apatite, chlorite, xenotime, and, locally, gold. Total REE oxide content of samples of the ground mass material, which are not diluted with lithic fragments, average about 20 weight percent. Grades from working faces in the mine are lower and average about 12 weight percent. Gold distribution is erratic, but concentrations are as high as 371 parts per million.

Jan 1, 1991

By Young C. Kim

Because of the tremendous technological advances achieved in recent years in microcomputers, it is not only technically feasible but also economically viable to develop an automatic truck dispatching system using a microcomputer. Such an effort was initiated by the Department of mining and Geological Engineering, University of Arizona in the summer of 1983. Up to date results and experiences prove that today's microcomputers can be economically employed for such a system to be used at small to medium scale open-pit mines. An IBM/XT microcomputer with 10 MB harddisk storage, together with automatic sensing capability of truck movements at several key locations in the pit, formed the core of this system. System software is written primarily in MICROSOFT FORTRAN with supporting subroutines in MACRO assembly language. The software is designed to automatically monitor truck movement throughout the pit, to make heuristic assignments based on expected shovel availability and truck travel times, and to record production statistics. It is currently dimensioned to handle 50 trucks, 10 shovels, 10 dump sites and 3 material types. Due to the lack of funds to purchase the necessary communications hardware, the work related to the automatic sensing of truck movements has not been performed to date. Otherwise, the automatic truck dispatching-system is fully operational on a realtime mode.

Jan 1, 1984

By K. Thirumalai

The Bureau of Mines has developed and tested a new concept of combining thermal and hydraulic energy processes for hard rock cutting. The study shows that this novel combination method overcomes the fragmentation limitations of the thermal process in nonspalling rocks and the cuttability limitations of the hydraulic process in high-strength rocks. The method effectively cuts hard rocks at moderate hydraulic pressures (below 30,000 psi). Theoretical predictions of the rock damage process are made and are correlated with experimental results obtained by using both single pulse and continuous water jet hydraulic systems. Traversing point heating and line heating techniques were used for heating rocks preceding the continuous jet impingement. Heating induces structural weakness of the rock material and assists fragmentation by the water jet impingement. The thermohydraulic process is effective if the significant depth of heat penetration induced by the surface heating exceeds the cutting depth produced by the jet impingement. Hydraulic specific fragmentation energy values reduce by about an order of magnitude using the combination technique. The process efficiency and the rate of themohydraulic hard rock cutting increases significantly by increasing the intensity and duration of heating.

Jan 1, 1973

By A. Arik

1his paper presents a modified ordinary kriging technique referred to as the "Nearest Neighbor Kriging" (NNK). The method is a simple and practical tool to use when the ordinary kriging (OK) results are unreasonably smooth, especially when estimating recoverable ore reserves for deposits with skewed grade distributions. NNK is robust and globally unbiased like OK. However, it is more advantageous over OK because it can control some of the smoothing and conditional bias which have been the major pitfalls of OK in many grade estimation cases. The paper details the methodology of NNK and its application to a gold deposit.

Jan 1, 1998

A Mark IV surface force apparatus (SF A) was used to conduct direct force measurements in dodecylamine hydrogenchloride collector solution between mica surfaces at varying pHs. It has been found that the long-range hydrophobic forces reach a maximum at pH 9.5, which also corresponds to the maxima attained by the contact angle and flotation recovery of quartz. The charge densities are comparable on both mica and quartz surfaces (0.40-0.48 run2), making it possible to draw conclusions on the flotation of quartz from the direct force measurements conducted on mica. Therefore, it may be suggested that the maximum flotation recovery of quartz m the range of pH 8.0-10.3 may be attributed to the appearance of long-range hydrophobic force, which in turn can be related to the formation of a close-packed monolayer (or hemimicelle) in the presence of neutral amines formed as a result of hydrolysis.

Jan 1, 1996

By W. M. Hart

The remote face loading and entry convergence monitoring systems, employed at some of the Cyprus Amax's underground coal mines, have been able to continuously record changes in face shield resistance across and entry convergence ahead of the longwall face at any moment during longwall mining. The instrumental data obtained from these systems plus in-situ observations during the mining operation can help us better understand the mechanism of overburden strata movement above a longwall face and verify the effectiveness of the current face and entry supports. This paper describes the functions of both the face and entry monitoring systems, and discusses our findings and the issues related to successful ground control for longwall mining.

Jan 1, 1996