Search Documents

By Phil Dakin, Rajiv Chandramohan, John Lo Grande, Greg Lane

Crushing and grinding circuit availability is a critical design factor defining the installed equipment selection and the process buffers required to maintain throughput during maintenance. The comminution circuit typically accounts for a process plant’s largest capital expenditure and energy use. Effective process and equipment selection and layout optimization are crucial steps when combining the objectives of cost-effective design and high circuit availability in operation. This paper outlines fit-for-purpose design principles for optimizing process flow, eliminating standby equipment and reducing buffer residence time whilst improving maintainability and operability.

Feb 1, 2025

By L. Donovan Clark

The term "powder factor" is almost universally accepted as the measure of the efficiency of a blasting program. It represents the economics of blasting since it designates quantity of explosive (thereby providing quality control in rock fragmentation) in terms of the associated volume broken. It is the wide use of this concept that explains the interest shown in an approach to rock blasting preferred by A. W. and Z. W. Daw* in a treatise on 3 blasting (1) substantiating its use in the form, Q = CVW3 for single shot hole, where Q = quantity of explosive lb Cv = blasting coefficient W3 = unit volume of rock It is obvious that the term Cv could also be called the apparent powder factor should the equation be written in the form, Cv = Q/W3 (lb per cubic unit). However, while the approach was ingenious** and the practical applications straightforward, their original, rather limited experimental work, along with certain assumptions, was questioned.

Jan 1, 1970

By C. McAllister, D. Preece, J. Berendzen

"The Multiple Blasthole Fragmentation (MBF) model models multiple explosive charge contributions and the effect on fragmentation of delay timing with its associated scatter for each blasthole. The model uses near-field blast vibration attenuation parameters and the ground p-wave velocity as inputs for part of the in situ rock property to model rock fragmentation. It models most blast design parameters explicitly and simulates the effect of wave reinforcement due to the interaction of simultaneously arriving waves or diminishing cooperative contribution from long delay intervals between charges within a blasthole or among blastholes. The fragmentation size is calculated at three-dimensional grid points within a blast, and the fines and oversized blocks are treated explicitly. The model takes a surveyed irregular geometry of the free face of a blast as the calculation boundary.This paper presents a case study on applying the MBF model at an openpit mine. Near-field vibration measurements from signature hole blasts were conducted to obtain the stress-wave magnitude and attenuation parameters as well as ground sonic velocity. A production blast was then monitored with the corresponding fragmentation measured, serving as site-specific inputs to the MBF model. Various blast design scenarios were then simulated to develop ones that provide better fragmentation to improve mill throughput for the mine. IntroductionThe semiempirical fragmentation models currently found in the literature (Cunningham, 1987; Lownds, 1995) cannot explicitly model contributions from multiple blastholes with varying delay intervals. Most of these models are not three-dimensional. Furthermore, these models predict an average fragmentation size within a volume surrounding a blasthole and use the average size to generate a size distribution over the volume. The percentage of fines and oversize blocks is included in the distribution. Typically, such models are inadequate for predicting fines and oversize blocks (Cunningham, 1987)."

Oct 1, 2016

By John A. Breslin

The U.S. Bureau of Mines develops technology to help ensure that the Nation has an adequate and dependable. supply of minerals at reasonable economic, human, and environmental cost. Our research programs seek improvements for almost every aspect of the mineral production cycle--from evaluating the availability of minerals, removing the ore from the earth, to enhancing the performance of mineral materials. The health and safety of the men and women who work in the Nation's mines and minerals processing plants and the environmental impact of mining and mineral processing are major Bureau research concerns. In recent years, the U.S. mineral industry has found it increasingly difficult to compete for a share of world markets. Many foreign producers benefit from lower production costs and higher grade deposits. Some foreign governments subsidize their mineral industries and impose fewer restrictions with respect to environmental controls and health and safety regulations. If the United States is to compete in world mineral markets, innovative technology must be found to lower the cost of recovering and processing minerals. Mining and mineral processing research by the Bureau identifies ways to help the country maintain a sound, competitive industry and a dependable mineral supply, so vital to economic growth and the national security. This work includes efforts to improve existing techniques and procedures; but more and more of the Bureau's resources are being focused on long-term, high-risk research directed at developing new approaches to mining and mineral activities--approaches like in situ mining. Bureau scientists are studying the mining applications of computer assisted mining and investigating a variety of "high tech" approaches to extractive metallurgy. Such cutting-edge research will be necessary if major advances in health and safety, environmental quality, strategic and critical minerals availability, and overall U.S. competitiveness are to be achieved. It is just such high-risk research that the industry cannot afford to conduct itself, but--in the long run--cannot afford to be without. It is this type of research that will help us arrive at a revolutionary breakthrough rather than small incremental changes in health and safety technology as well as recovery methods. Our mining and mineral processing research is also directed at reducing the Nation's dependence on imports of minerals that have key defense and industrial uses. Some of these strategic and critical minerals are particularly vulnerable to supply disruptions. We are working on technologies that would allow the United States to take advantage of domestic sources of these minerals--sources consisting primarily of deep or low-grade ores, ores with complex mineralogy we do not yet know how to process, and small deposits that are now uneconomical to mine and process. Other research activities focus on ways to reduce the Nation"s consumption of key minerals and increase the recycling of these minerals. The opportunities in this area include coal. The current middle eastern crisis reinforces the need for a stable energy supply--preferably a domestic supply. The extensive reserves of coal in this country are well documented. Perhaps what is not as well recognized is the impact that the price of coal can have on its competitive position both for domestic fuel selection considerations as well as for the ability of this country to compete in the coal export market. Today, the role to the United States is as a reliable, but high-cost exporter of high-quality coal. U.S. export coal competes with supplies from other major suppliers, including Australia, Canada, Poland. If U.S. mining costs were lowered by at least $8 per ton in the year 2000, then coal exports would surge by a projected 46 percent, and U.S steam coal displaces significant quantities of foreign coal imports in Europe. Further cost reductions would make

Jan 1, 1991

By RALPH BALTES, AMIR EHSAN KIANFAR, FABIAN UTH, ELISABETH CLAUSEN

  Underground positioning and communication are essential technologies for the future of underground mining operations. In contrast to other positioning and communication technologies such as wireless local area network (WLAN) or radio frequency identification (RFID), ultra-wideband (UWB) radio technology provides significant benefits like accurate and robust positioning of mobile machine equipment, which is indispensable for future autonomous systems in underground mining processes, such as production, transportation and auxiliary operations. Among these technologies, UWB offers many advantages, including higher accuracy, robustness, resistance against noise and multipath effects, and low power consumption [1,2]. Underground automation and localization systems benefit from these advantages and use the technology to improve efficiency and safety. There are many studies being carried out on this technology to increase the results’ accuracy, energy sufficiency and more. Two robust UWB modules that were developed for underground positioning and collision avoidance with regard to human safety in underground mining operations are introduced. The measurement results of tests carried out in an underground mine are discussed as well to confirm the functionality of the system.

By REHMAN ATTA UR, Kwame Awuah-Offei

This work evaluated the effects of bucket orientation and operating parameters on resistive forces and penetration for rubber-tire loaders (RTLs), such as load-haul-dumps (LHDs) and front-end loaders (FELs). The work used a 1:16 scale LHD model to test an RTL bucket operating at different levels of traction (tractive effort), speed, digging height and rake angles in a full factorial design experiment. The test was repeated on two muck piles with different particle sizes, and generalized regression modeling was applied to test the association of rake angle, tractive effort, speed and digging height on penetration and resistive forces for RTL buckets. The results show that speed and tractive effort are more important in explaining RTL penetration and resistive forces than height above the floor and rake angle. Speed, tractive effort and height above the floor are positively correlated to bucket penetration, whereas the rake angle is negatively correlated to penetration. Similarly, speed, tractive effort, rake angle and height above the floor are all positively correlated to resistive forces incurred during initial penetration. The results show that the combined effect of speed and tractive effort is negatively correlated to penetration and resistive forces — a novel finding that enhances our understanding of RTL loading. The results also show that the effects of speed, tractive effort and height above the floor all change with changes in particle sizes. This work provides insights into the effects of rake angle, height above the floor, tractive effort and speed on penetration and resistive forces for RTLs to facilitate better design and efficient use of these loaders.

By M. T. Ityokurnbul, M. P. Trubelja

Concentrate flow rates were measured for the flotation of -100-mesh Lower Kittaning coal in a computer-controlled 0.076 x 3.5-m pilot flotation column. The variables studied were recovery zone height, airflow and solid feed rates. The specific projected surface areas of the feed, concentrate and tailing streams were determined from the measured particle size distributions. The results obtained show that the concen¬trate flow rate was independent of recovery zone height but was dependent on the hydrostatic pressure setting (measure of froth depth), gas flow rate, solid loading and particle size. New correlations for column carrying capacity and yield are provided as a function of bubble surface area flux and the specific particle projected surface area.

Jan 1, 1999

By Robert G. Beverly

INTRODUCTION Standards limiting the annual exposure of United States uranium miners to radon daughters were established in 1967 at 12 Working-Level-Months (WLM). The standard was reduced by a factor of three, to 4 WLM, in 1971. Currently, the standard is again being examined to determine if it should be changed. Since 1967, Union Carbide has calculated individual monthly exposures in company and contract-operated mines located on the Colorado Plateau. Although it has been possible, by extensive ventilation control measures and accurate routine sampling, to meet the current exposure standard, there are many miners whose exposures closely approach the 4 WLM standard for any given year. However, it was noted that for miners who work for any extended period of years the [average] exposure was much less than the standard. The primary purpose of this paper is to show that, in effect, any annual exposure standard to radon daughters results in a long-term exposure considerably below that standard. Further, most miners, due to their job assignments and/or employment habits, only receive a small fraction of the standard. HISTORY OF EXPOSURE STANDARDS Prior to 1967, radiation protection in uranium mines was fundamentally based on a radon daughter concentration guide. In 1960, the American Standards Association published mine and mill radiation protection standards (ASA-1960). The Colorado Department of Mines, in 1961, adoped a standard which followed the ASA Standard and provided that if concentrations exceeded 10 Working Levels (WL), the area was to be shut down until corrective action was taken; if between 3 and 10 WL, corrective action was to be initiated; between 1 and 3, additional samples were to be taken and individual exposures evaluated; and if below 1 WL, conditions were considered to be controlled. In 1967, the U.S. Department of Labor issued the first exposure standard which called originally for limiting annual exposures to 3.6 WLM but which was later changed to 12 WLM. The complicated regulatory developments leading to this standard have been described elsewhere (Beverly-1969, Rock & Walker-1970). Effective July 1, 1971, this exposure standard was lowered to 4 WLM per year, which is the current standard. Over the past year, there has been speculation about the potential risk to uranium miners working at the present standard. A recent NIOSH Study Group Report (NIOSH-1980) concluded: "There is also strong evidence that a substantial risk extends to and below 120 WLM of exposure." The 120 WLM corresponds to a miner working in uranium mines for 30 years, a rare occurrence, at an exposure rate of 4 WLM per year, an even rarer occurrence. On the other hand, the General Accounting Office, in a recent Report to the Congress (GAO-1981), was very critical of reports by NIOSH on general low-level radiation risks. The GAO recognized that”...important questions remain unanswered about the cancer risks of low-level ionizing radiation exposure;" and recommended that Congress enact legislation giving statutory authority to an interagency committee to coordinate Federal research on health effects of ionizing radiation exposure. The International Commission on Radiation Protection at its March, 1980 meeting recommended limiting the inhalation of radon daughters to 0.02 J per year, equivalent to 0.4 WL, which on an annual basis would be 4.8 WLM and noted it is common to reduce this figure by 20% for allowance in the case of uranium miners for external and/or dust exposure(Sowby-1980). This is essentially equal to the present standard of 4 WLM. As earlier uranium miner exposure studies are reevaluated, and as new studies are conducted, it is important that the relationship between regulatory standards and the resulting actual exposures be recognized. UNION CARBIDE URANIUM MINING EXPERIENCE Union Carbide started mining Colorado Plateau uranium-vanadium ores in the late 1920s for the contained vanadium values. In the early 1950s, the Atomic Energy Commission contracted Union Carbide to produce uranium at mills located in Uravan and Rifle, Colorado. The company now has over fifty years of mining experience in the area. Some mines are operated as company mines and others are operated by private mining companies under a contractual arrangement. Ventilation, sampling, and exposure calculations are carried out the same in contract mines as in company-operated mines. Data presented in this report do not differentiate between company or contract employees and include all employees who worked underground any portion of a year in Union Carbide mines from 1967 through 1980. At the peak of uranium mining activities in 1970, there were 577 miners employed at year end (285 company employees and 292 contract) and 52 mines in operation (8 company-operated and 44 contract mines). Contract mines varied from two-man operations up to 15 employees. Company mines were generally the larger operations and employed from 20 to 100 miners.

Jan 1, 1981

By Jon A. Hummer, MICHAEL R. SHAHAN, Aleksandar D. Bugarski, Shawn Vanderslice

Occupational exposures to respirable dust and submicrometer aerosols emitted by diesel-powered equipment are a health concern for underground mining operators and regulators. A study was conducted in an underground mine with the objective to identify, characterize and source apportion airborne aerosols at the setup face and recovery room during longwall move operations. 

By Rambabu Pothina, Rajive Ganguli

The economics of a mineral-processing circuit is dependent on the numerous sensors that are critical to optimization and control systems. When a sensor goes off calibration, it results in errors that can have a severe impact on plant economics. Classical statistical approaches fail to detect when errors are “subtle,” unless they grow and become large enough to be “gross,” whereas methods based on signal processing and artificial intelligence fail in dealing with the complexity of process fluctuations. Due to the sheer volume of sensors, undetected errors are not remedied until the next calibration, which on average are a year apart across all industries [1]. This research aims to detect such subtle errors (2 percent bias) in shorter time spans of about a month — rather than wait for errors to grow — using innovative data-mining techniques and algorithms.

By L. Yuan, R. A. Thomas

"Atmospheric monitoring systems (AMS) have been widely used in underground coal mines in the United States for the detection of fire in the belt entry and the monitoring of other ventilation-related parameters such as airflow velocity and methane concentration in specific mine locations. In addition to an AMS being able to detect a mine fire, the AMS data have the potential to provide fire characteristic information such as fire growth — in terms of heat release rate — and exact fire location. Such information is critical in making decisions regarding firefighting strategies, underground personnel evacuation and optimal escape routes. In this study, a methodology was developed to calculate the fire heat release rate using AMS sensor data for carbon monoxide concentration, carbon dioxide concentration and airflow velocity based on the theory of heat and species transfer in ventilation airflow. Full-scale mine fire experiments were then conducted in the Pittsburgh Mining Research Division’s Safety Research Coal Mine using an AMS with different fire sources. Sensor data collected from the experiments were used to calculate the heat release rates of the fires using this methodology. The calculated heat release rate was compared with the value determined from the mass loss rate of the combustible material using a digital load cell. The experimental results show that the heat release rate of a mine fire can be calculated using AMS sensor data with reasonable accuracy.IntroductionFires at different stages generate different gases and smoke toxicity hazards. When fires occur in underground mines, a significant amount of toxic gases and smoke enter the mine ventilation system and are carried throughout the mine ventilation network, increasing the hazard potential for personnel even if far away from the actual fire. Although fires that develop to the point of rapid flame spread pose imminent hazards, fires in their smoldering, pre-flaming stages can also contaminate the mine atmosphere with debilitating levels of smoke and toxic gases.The most important parameter for evaluating the fire hazard in mines is the heat release rate (HRR), which is directly related to the rate at which heat, smoke and toxic gases are produced and transported by the ventilation system and which provides an indication of the time available for escape or firefighting (Babrauskas and Peacock, 1992). The HRR is also an important input parameter to mine fire simulation models."

Jan 6, 2017

By Debra Switzer, Swapnil Urankar, Douglas Watson, Steven Hunter, Chandranth Banerjee, Shashank Pathak

A hydrocyclone is a piece of equipment commonly used as a classifier in mill circuit operations. Traditionally, hydrocyclone performance is characterized by the classification efficiency parameter, such as cut size (d50c), sharpness of separation () and bypass (Rf ). A plethora of endeavors have already been made to develop parametric models to determine hydrocyclone performance that correlate design and process variables. In contrast to those studies, we made an attempt to develop an approach to derive required design parameters purely from hydrodynamic principles that provides a platform to optimize the operation of a hydrocyclone for a given application. In this selection methodology, we calculated the differential pressure at the air core, as well as the tangential velocity at the boundary of the air core from the vortex principle in a confined geometry at different operating regimes. A series of experiments were conducted using Weir’s Cavex® hydrocylone where process variables—such as solids concentration and feed flowrates—were experimentally studied to determine the key classification parameters. For the validation of the current approach we used the same process variables to derive design parameters and compared them with the existing design. The current approach can provide insights towards the selection of design parameters and can be useful for mining industry professionals to optimize different operating parameters of hydrocyclones to achieve the best performance.

Feb 1, 2024

By Andrea Brickey, RICHARD AMOAKO, Akshay Chowdu

Production forecasts derived from the medium-term schedule represent the best path forward for underground mining operations to achieve corporate and operational goals. Unforeseen circumstances, such as equipment breakdown, can cause significant deviations from established production forecasts in the short term. Such situations require timely mitigation of the effects of the deviations in order to stay as close as possible to the medium-term plan. This paper presents a deterministic mathematical formulation for short-term scheduling that addresses this challenge. The formulation is able to make up for deficits resulting from operational disruptions by minimizing deviations from medium-term production goals and medium-term activity start dates. We demonstrate this in a case study by simulating disruptions involving reduction in ore extraction capacity and development advance rate. Aside from the rescheduling capability, this formulation can help mine planners conduct analysis on the impact of various disruptions on the schedule. The formulation can help identify those conditions or disruptions that are more detrimental to the achievement of forecast targets, or otherwise. The formulation also affords mine planners the flexibility to prioritize one production goal over the other, depending on operational conditions at the mine. In the future, we seek to incorporate in the formulation respirable dust, diesel particulate matter and ventilation constraints in order to create more realistic schedules, and enhance miners’ health and safety.

Jan 1, 2024

By Thomas D. Barkand

Investigation of several serious hoisting accidents identified machine brake failure as the most common cause. The recent revelation of this potential hazard has prompted regulatory authorities to require an additional, independent, emergency braking system. As a result of this initiative, a new generation of braking systems have been developed and applied to mine elevators. This paper will discuss the design and testing of an electrical dynamic brake, pneumatic rope brake, and traction sheave brake. The effect of compound braking on hoisting systems equipped with multiple brakes will also be addressed.

Jan 1, 1992

By A. W. Storm

Vertical shaft furnace design and operation have their roots deep in antiquity. There is substantial evidence to indicate that iron was reduced from its oxides to serve mankind's needs long before recorded civilization - - actually prior to 3500 B .C. For at least 5500 years man has been matching wits with Nature to find better methods of extracting this most common, yet essential, metal from her, grasp. And, during nearly all of this period, the vertical shaft furnace has played a principle role in this dramatic struggle.

Jan 1, 1962

By J. F. Brune, A. Verma

"Face ignitions in underground coal mines are a major risk for underground mining operations, as they can lead to methane or coal dust explosions. The 2010 disaster at the Upper Big Branch Mine resulted in 29 fatalities due to a methane and coal dust explosion initiated from a face ignition. Much research has been conducted to mitigate face ignition hazards, from water sprays to installing passive and active explosion barriers. Despite the increased use of water sprays in U.S. coal mines, there have been more than 50 documented face ignitions in the U.S. underground coal mines since 2010, indicating that this hazard still prevails. This paper will examine the statistics of face ignitions and gas explosion in U.S. coal mines based on MSHA data. It will study factors contributing to these face ignitions and outline best practices for their prevention based on experience and practices worldwide. INTRODUCTION Methane and coal dust explosions are one of the major causes of coal mine disasters in the U.S. and around the world. Such disasters have resulted in the large number of fatalities and loss of mine infrastructure. The recent explosion at the Soma coal mine in Turkey has caused the death of 301 miners (Mining Turkey, 2014). As documented by U.S. Mine Safety and Health Administration (MSHA, 2015a), the U.S. coal mining industry has also experienced several catastrophic mine explosions with accidents at Upper Big Branch mine, Darby mine, Sago mine and Jim Walter Resources No. 5 mine in the last decade, causing the deaths of almost 60 miners. Every explosion requires a source of ignition, the right amount of fuel and oxygen. In underground coal mines, methane acts as a fuel while ventilation air acts as a source of oxygen. The source of ignition may vary from spontaneous combustion, electrical equipment and switchgear, mechanical heat sources, face ignitions due to friction rock-on-rock or from cutter bits and lightning strikes. Under the right conditions, energy of less than 0.3 mJ is sufficient to ignite methane-air mixtures (James, 2007) that can result in a catastrophic explosion. Much research has been done to mitigate the methane explosion hazard by proper dilution, continuous monitoring of methane and elimination of ignition sources. Historical studies indicate that face ignitions are the major cause of explosion in underground coal mining operations worldwide (Belle, Carey, and Robertson, 2012). Statistics shows that most mine disasters were started from a small face ignition, which turned into a major explosion fueled by additional methane and coal dust (Belle et al., 2012). To investigate face ignition hazards, researchers must study potential ignition sources as well as potential explosive atmospheres near mechanical coal cutting operations. Statistical analysis of U.S. coal mine face ignitions reported by the U.S. Mine Safety and Health Administration (MSHA, 2015b) shows that several factors are responsible for face ignitions."

Jan 1, 2016

By Gene E. McClelland, Dirk J. A. van Zyl

5.1 INTRODUCTION Heap leach cyanidation techniques possess considerable potential for exploitation of low-grade ores, small ore bodies, mine strip waste and tailing materials where fine grinding is not necessary for good extraction. For heap leaching to be successfu1, ore must exhibit certain characteristics, as previously discussed in Chapter 1. Primary among the necessary ore characteristics is that the ore must have good permeability after being crushed or treated and stacked into heaps if uniform distribution of the cyanide leach solution is to be achieved. Gold and silver ores containing excessive amounts of clays or fines generated by crushing are some of the most difficult to treat successfully by heap leaching. The presence of excessive amounts of slimes (generally classified as minus 50-micron or 270 Tyler mesh sieve size particles) in the heap leach feed will slow the percolation flow of the leach solution, cause channeling, or produce dormant or unleached areas within the heap. This may result in unreasonably long leaching periods and poor extractions. In extreme cases, the clays or slimes can completely seal the ore heap, causing the leach solution to run off the sides of the heap rather than to penetrate the ore heap. The problem of heap leaching ores containing fines can be aggravated during stacking and preparation of the ore heaps, because natural sorting of coarse and fine material occurs during these steps (Johanson, 1978). This phenomenon results in a concentration of ore fines at the center of individual ore piles and a concomitant concentration of larger rock fragments on the lower slopes and base of the piles. When the individual piles within the heap are leveled off prior to installation of the sprinkling system which delivers the leach solution, additional segregation occurs as the fines sift through the coarser ore particles. The segregation results in localized areas or zones with marked differences in permeability. As a consequence, the leach solutions follow the path of least resistance, percolating downward through the coarse ore regions and bypassing or barely wetting areas that contain large amounts of fines or slimes. Effective utilization of marginal gold and silver resources through heap leach processing requires the development of new methods in order to achieve more uniform size distribution during ore heap preparation and better slime control during leaching.

Jan 1, 1988

By A. S. Paschoa, A. W. Nóbrega

INTRODUCTION There are now over twenty years since the radiological characteristics of the brazilian regions of Araxá, Tapira and Barreiros, three locations adjacent to each other, in the state of Minas Gerais, Brazil, started being surveyed by investigators from the Instituto de Biofísica da Universidade Federal do Rio de Janeiro (IB/UFRJ), Pontifícia Universidade Católica do Rio de Janeiro (PUC/RJ), and New York University (NYU) (Roser and Cullen, 1958; Cullen et al, 1980). The importance of the Araxá apatite – Ca5,(P04)3(OH, F, Cl) - and pyrochlore - NaCaNB206F - for the production of large quantities of fertilizers and niobium was early recognized (Roser and Cullen, 1958). Interesting data have been gathered and published throughout the years on the contents of naturally occurring radionuclides in geologic materials, soils, grass, foods and waters of the Araxá region (Eisenbud, et al., 1964; Penna Franca, et al., 1965a, b; Roser et al., 1966; Penna Franca et al., 1970; Cullen, 1977; Penna Franca, 1977; Cullen and Paschoa, 1978; and Cullen et al., 1980). The radioactivity of the Araxá region is associated with mineral deposits of niobium rich pyrochlore and phosphate rich apatite. There are in this region mineral ores with 3 to 5% pyrochlore with 2 to 2.5% Th as Th02 and 50 to 150 ppm U308 in the matrix, while the apatite deposits contain up to 150 ppm U308 and a thorium concentration similar to that of the pyrochlore deposits (Paschoa and Palacios, 1981). As an indication of the high thorium content of the Araxá soils the 228Ra and 224Ra activity concentrations were reported to range from 10.6±0.2 to 62.4±0.7 pCi228Ra/g soil in 7 samples and 2.1±0.1 to 104±1 pCi224Ra/g soil in 19 samples (Cullen, et al., 1966). The uptake of radium isotopes by edible roots vegatables and fruits growing in the soils of the Araxá region can be illustrated by the data listed in Table I. The biological availability of natural radium isotopes in some segments of the Araxá soil allows a large variation in the 228Ra, 224Ra and 226Ra concentrations in vegetables and edible roots, as can be seen in Table I. This fact makes quite difficult a quantitative local assessment of the radiological implications of mining the Araxá mineral deposits of pyrochlore and apatite for production of niobium and phosphate fertilizers, respectively; since one cannot easily separate the naturally occurring from the technogically enhanced radionuclide contents of foods. The position of the city of Araxá inside the contour of the state of Minas Gerais appears in the upper part of Figure 1, which shows the outlined map of Brazil with the positions of the cities Brasilia and Rio de Janeiro also indicated. The lower part of Figure 1 is a representation of the Araxá region in an expanded scale, which indicates the locations of the pyrochlore and apatite deposits in relation to the city of Araxá, as well as the nearby hydrographic basins. The distance between the city of Araxá and the pyrochlore deposit is about 8 km, and between the pyrochlore and apatite deposits is 4 km. This paper deals tentatively with the radiological implications of the industrial operations taking place in the Araxá region for the exploration of the pyrochlore and apatite deposits. However, one must bear in mind, firstly, that the radiological implications of these industrial activities are by far too complex to be covered adequately by the limited amount of data to be presented in this paper, and secondly, that such implications cannot be considered of local character only. INDUSTRIAL OPERATIONS The commercial exploration of the Araxá deposits of pyrochlore and apatite started only few years ago, motivated by the increasing demand of niobium and phosphate fertilizers in Brazil and the world. As a consequence of the industrial operations in Araxá, a redistribution of the uranium, thorium, and radium originally present in the local deposits of pyrochlore and apatite started occurring in the seventies, with possible radiological implications for the Araxá region and its immediate surroundings, not to mention the destinations of the end products of such industrial operations. A literature review on the radioactivity associated with the extration industries of selected minerals was made by the USEPA (Bliss, 1978). The low level radioactive wastes of the industries for copper ore mining and rare metals processing have been object of particular attention (Fitzgerald, Jr., 1976; Eng, et al., 1979), but the short and long term implications of the radioactivity associated with the niobium industry were also subjects of concern (Knight and Makepeace, 1978). Recently, high 232Th and 226Ra concentrations in samples from the tin mining industry in West Malaysia were reported (Hu et al., 1981). A great deal of attention has been dedicated to the implications of the redistribution of radionuclides originally present in the mineral ores used by the phosphate fertilizer industry (Moore, 1967; Menzel, 1968; Spalding and Sackett, 1972; Eisenbud, 1973; Guimond and Windham, 1975; Guimond, 1976; Roessler,

Jan 1, 1981

By Jeremy Maurer, Duah Philip, Awuah-Offei Kwame, Donya Otarod

Land use impact assessment for mining is time- consuming and expensive. Because of mining’s impact on biodiversity, land use assessment methods that evaluate biodiversity are important for mining land use impact assessments. Remote sensing, in particular satellite multispectral sensing platforms such as Sentinel‑2 and the Landsat mission series, have been used to assess and quantify biodiversity through proxy variables such as NDVI (Peña-Lara et al., 2022). The objective of this paper is to present results of a comparative study of land use and biodiversity based on multispectral satellite observations and production data from copper and cobalt mining in the Democratic Republic of Congo. We quantify the relationship between different spectral bands and vegetative indices and the production data provided by the mining companies and measure correlations. The results suggest that remote sensing could be a cost- effective means of assessing biodiversity impacts of mining.

Feb 1, 2025

By Mark E. Gershon

A mixed-integer formulation of the mine scheduling problem is discussed and applied for the purpose of optimizing both the mine production sequencing and the mill blending and processing problems simultaneously. Previous attempts at solving these problems separately, although successful, fail to take into account the interrelationships between these problems. Project structure serves as the outline of this paper, which is directed towards a mining engineering audience. Generalized in its organization, this concept is useful for long, intermediate and short range scheduling. Actual applications are mentioned which show that the concept is also applicable to mining a variety of ores.

Jan 1, 1982