Search Documents

By Angus Campbell, Michael J. Gobla

Numerous techniques for treating, controlling, and preventing acid rock drainage have been applied at the Summitville Mine Superfund Site. Challenging aspects of the remote mine site include the wide-spread occurrence of acid-generating soils and rocks, extensive surface and underground mine workings, and a cold and wet climate. Water treatment was an immediate necessity when the Government took control of the abandoned site in December of 1992. Subsequent reclamation activities have emphasized prevention and control of ARD to minimize future water treatment requirements. A combination of conventional, innovative, and experimental methods are being applied to successfully mitigate ARD at Summitville.

Jan 1, 2000

By Andy W. Stephens, William H. Langer

In Australia and America, encroachment by conflicting land uses, zoning restrictions, and the "not in my backyard" syndrome make it increasingly difficult to access high-quality aggregate resources located near the market areas. Attempts by government agencies in America to protect aggregate resources for future development have met with varying degrees of success. The State of Queensland, Australia, designates aggregate resource areas as Key Resource Areas, which protect the resource and the routes to transport the resource, provide a separation area from incompatible land uses, and indicate the likelihood that the area is free from conflicting social or environmental issues.

Jan 1, 2005

By Robert C. Dunne, Jeffery P. Vaughan

The Archean ores of Western Australia are in total the largest producers of gold in Australia. In addition to numerous small and medium sized deposits, the province also contains the giant Kalgoorlie Golden Mile deposits. A variety of different gold ore mineralogical associations has lead to the development of a number of different processing routes for both refractory and non-refractory ore types. Intense weathering and lateritization of Archean greenstones in the semi-arid Yilgarn region have resulted in the development of a deeply oxidized profile (60-100m) above most sulphide orebodies. Residual and re-deposited supergene gold within iron oxide/silica gangue of this zone responds well to CIP, CIL, heap and vat leaching techniques. Although gold is easily liberated in principal from oxidized gangue, in practice recoveries are sometimes affected by iron oxide coatings on gold grains, and by clay minerals which can interfere with plant performance. Refractory ore types in the Eastern Goldfields fall into three main categories - pyritic, arsenopyritic and telluride-bearing. Pyritic ores may be either free milling or require roasting. The difference appears to depend largely on whether gold occurs along grain boundaries or fractures, which can be liberated by grinding, or whether gold occurs as inclusions within pyrite grains and therefore cannot be satisfactorily liberated by grinding. Arsenopyrite bearing ores are not well understood and are complicated by what appears to be a variable degree of gold solid solution, in addition to included gold. Gold occurring in complex gold-silver telluride assemblages has traditionally been recovered by roasting in the Eastern Goldfields.

Jan 1, 1987

By Daniel R. Stewart, Ralph R. Sacrison

The function of the geological engineer is to assist in mine planning and operations by collecting, interpreting, and applying geologic data to the solution of engineering problems. The geologist supports this effort by collecting additional geologic information specifically useful to the engineer. This use of geologic information reinforces the value of mine geology to the mining process beyond the traditional role of orebody definition. Work discussed includes: evaluation of caving strategies at the Climax and Henderson mines, support definition and slope stability at the Climax mine, and some uses of geology in cavability estimation for the Mount Emmons project.

Jan 1, 1992

By H. V. Alminas

The U.S. Virgin Islands consist of three major islands (St. Thomas, St. John, and St. Croix) and some 50 smaller islands that are located primarily along the coasts of St. Thomas and St. John. St. Croix, the largest of the islands, is located approximately 160 km south-southeast of San Juan, Puerto Rico and is about 218 km in area (Fig. 1). St. Thomas, the second largest island is located 64 km east of Puerto Rico and incorporates approximately 77 km2. St. John is located immediately to the east of St. Thomas and incorporates approximately 49 km2. The climate in the U.S. Virgin Islands is maritime tropical. The average annual rainfall at higher elevations is 127-152 cm and at lower elevations 51-76 cm. There is no well-defined wet or dry season. Temperatures generally average in the 80's (F°) with only a 5°-7° F variation throughout the year.

Jan 1, 1987

By Kugan Kuganathan

Pastefill is being increasingly considered as a viable fill by underground mine operators. Mount Isa Mines (MIM) chose pastefill to fill their deep copper mine (>1200m deep) after considering various other types of fill in the feasibility studies. During the development of pastefill at Mount Isa (1996 - to date) the Mining research of MIM developed two cost effective, reliable and simple testing methods and used. With the help of these tests the behaviour of MIM pastefill was studied thoroughly and the most optimum mix design for pastefill was achieved. The MIM's pastefill plant, the largest in the world with a capacity of 450rph continuous pastefill production and unique in the process used, has been built (1998-1999) to produce pastefill to the specification developed through extensive testing program using the Flow Cone and Mini Slump cone Tests. As a consequence, it is now possible to select the optimum pastefill mix designs and predict their flow behaviour in bore holes or pipe lines using only these tests. MIM Blended Tailings Pastefill (BTPF) uses 3-3.55 Portland cement and the cost of pastefill is much lower than the total tailings pastefill, that could be produced from the same tailings.

Jan 1, 2001

By Jerry Luttman, Mark Dubay, Anvesha Dogra, Elizabeth Dwyre, Wei Hu

The I-75 Modernization Project (Segment 3) just north of Detroit, MI is being delivered as a Design-Build-Finance-Maintain (DBFM), which is a Public Private Partnership (P3). The project includes design and reconstruction of 5.5 miles of freeway, including a depressed section with a 20,630-ft long, 14.5-ft inside diameter, up to 100-ft deep stormwater tunnel, multiple drop shafts, and a pump station. The project also includes a maintenance term of 25-years. This is the first time MDOT has used a P3 delivery method for a major highway and tunnel project. This paper describes the development of the P3 documents, including performance-based tunnel and shaft technical requirements, and the approach to project risk management, financing, and insurance coverage.

Jun 23, 2024

By Bruce B. Hanshaw

The Tertiary carbonate aquifer of central Florida is composed of about 2/3 calcite and 1/3 dolomite with minor amounts of quartz and apatite. The Mg content of the calcite is lower in the recharge areas than in the deeper confined parts of the aquifer system. Various geochemical lines of evidence indicate that much of the dolomite is of penecontemporaneous origin but that some may have been formed much later, possibly by ground water. Theoretical studies indicate that the Mg/Ca ratio in solutions is about unity for the three-phase equilibrium, calcite-dolomite-water. Solutions, such as ocean water and some subsurface brines, have Mg/Ca ratios higher than one and should represent dolomitizing solutions. In the areas of principal recharge to the Floridan aquifer, ground water is undersaturated with respect to both calcite and dolomite, and the Mg/Ca ratiois as low as 0.05. As the water moves downgradient, the Mg/Ca ratio systematically increases and approaches unity; saturation of the solution with respect to both calcite and dolomite also increases with length of travel in the system. Thus, in the zone of active potable-water circulation, the chemical process is one of dissolution of minerals until saturation is reached or exceeded. However, in the deeper brackish-water zones that underlie peninsular Florida, dolomite may be forming where the Mg/Ca ratio is greater than one. The necessary Mg may be derived from ocean water or brines recycled through the system as the hydrologic regimen is changed. The driving force may be simple mixing, relative fluctuations of sea level, or a combination of mechanisms.

Jan 1, 1972

By Bill Kendall

"In coal mines, handheld air, electric and hydraulic powered drills are used along belt conveyors, in single entry development, in entries where there are obstructions, and in longwall recovering bolting. In hard rock mines, pneumatically powered jackleg drills are typically used in narrow vein mining. Drilling and bolting in narrow confines has traditionally been performed with pneumatically or hydraulically powered hand-held drills or newer electrically powered hand- held hammer drills due to their low cost, simplicity of operation, and extreme flexibility due to their small size. Mechanized equipment has typically been too large, too expensive, inefficient due to the confined space, and too restrictive due to lack of flexibility for use in narrow confines.Although the handheld equipment is effective, it requires operator exposure to certain inherent hazardous conditions in use. These include falling rock from the roof, rib and face; tripping hazards; bending twisting lifting hazards; high noise levels and chemical fumes from the pneumatic exhaust. The operation of the hand held equipment can adversely affect the long-term health of the operator - continual jackleg operation frequently results in longterm damage to hearing, shoulders, arms and wrist joints and back injuries. This results in a reduction in life style for the operator and higher personnel turnover rates for the mining company.Hand-held drills also typically have limited thrust and torque capability that limits their ability to push long resin bolts, inadequate torque to properly install resin bolts or to properly torque mechanical or tensioned rebar bolts. Hand-held drills do not offer any type of protection for the operator from roof or rib falls. They do not offer any means for handling roof or rib mesh. Since the operator stands on the ground the maximum safe drilling height without use of a ladder or "riding the drill" is limited to 2.44 m (8 ft)."

Jan 1, 2014

By A. Bhagwat, S. Tadolini

"Steel members of the ground support systems in underground mines are routinely exposed to corrosive environment that may range from acidic to alkaline. Corrosion of steel bolts leads to metal loss and thereby, reduction in strength and useful life. Protective coatings are commonly applied to the steel bolts to combat corrosion. However, coatings are expensive and often cumbersome in practical applications. Instead, Minova has developed an innovative technology based on sacrificial anodes. The anodes were designed from non-ferritic alloys that are inferior to steel on the Galvanic Series. This paper will present data from field testing to show significant benefit of the technology. Potential applications in current products will be discussed. INTRODUCTION Corrosion is a physical alteration of a steel material from electrochemical reaction with its environment that often results in reduction of the mechanical and physical properties of that material. Mine roof bolts, the subject of this investigation, are particularly susceptible to corrosion as they can be exposed in their working environment to ground water and air with high humidity. As other researchers have determined, corrosion increases markedly in sulfide ore bodies due to acid runoff. There are several types of corrosion that a rock bolt is likely to undergo when used for ground reinforcement in underground mines (Aziz et al., 2013). Of all the types of corrosion, pitting is particularly dangerous as it can remove capacity for the bolt to deform with subsequent strata movements. Sudden failure of a bolt is likely to occur when severe pitting corrosion is experienced. The type and nature of corrosion depend on the nature of the ground condition and bolt encapsulation. Generally, the type of corrosion and severity of the corrosion varies along the axis of bolt. Almost all of the mine roof bolts used in mines, with the exception of fiber reinforced polymers, are made from steel. The corrosion of iron is an electrochemical phenomenon with the overall equation:"

Jan 1, 2018

By Steven Hoerger

Mixed integer linear programming (MILP) production scheduling models can be used to evaluate if tonnage improvement projects will deliver value over all time periods and whether new bottlenecks will be created. These MILP models can evaluate the interconnected effects of mine and process capacities, mining locations, cutoff grades, stockpiles, and orebody grade/tonnage distributions. A case study compares potential value creation from a mine capacity increase, a mill capacity increase, or a simultaneous increase in all capacities. For perspective, project valuations for capacity increases are compared against valuations for cost reduction projects, mine planning improvements such as phase design, dynamic cutoff grades and stockpiling, and the impact of geostatistics improvements in the areas of block model accuracy and ore control selectivity.

Feb 1, 2024

By R. W. Smith, Z. Sadowski

INTRODUCTION Problems encountered in barite flotation from various waste materials such as spent drilling muds are likely to be closely connected with the effect of contaminant metal ions and other chemicals on the flotation. Investigations on the recovery of barite from tailings ponds and mining wastes (Sullivan and Lamot, 1981) have shown that such barite materials can contain large quantities of carbonate and silicate minerals (including clay minerals). Also iron oxide slimes can be present. From these substances, cations such as Ca2+, Mg2+, Fe2+, and A13+ can potentially dissolve and be present in the aqueous phase accompanying the various minerals. These ions and their hydrolysis products can have a substantial effect on any subsequent flotation scheme. The present study investigates the effect of the noted ions on both the stability and electrokinetic behavior of barite suspensions. Some adsorption (abstraction) experiments were also performed. Experimental materials and methods The barite used was a high-purity, naturally occur¬ring mineral sample (Kings Creek, SC). The material was ground in a porcelain mill and a fine fraction (mean particle size 11.49 µm) separated out by air elutriation. The mean size was determined by an aqueous sedimentation method using a CAHN electro-balance. In the method, an 0.6-g sample of the barite was dispersed in 450 cm3 of pH 7 water containing 0.01 g of sodium tripolyphosphate. The mean particle size was denoted X0. The stability of the barite suspensions was determined by a comparison of the mean size of the investigated barite suspension aggregations with the mean size of barite powder determined in the presence of sodium tripolyphosphate. The mean sizes (X) of the barite aggregations were determined using the same amount of water and barite sample as in the measurements of dispersed barite particle size but without the presence of polyphosphate. The ratio X/Xo is thus a measure of the stability of a suspension (the greater the ratio, the less stable the suspension). The adsorption (abstraction) experiments were carried out in polyethylene bottles containing 1 g of barite powder in 200 mL of solution. The solids were added to a solution containing a known concentration of metal chloride salts (AlCl3, FeCl2, MgCl2, and CaCl2) . The pH was controlled by both HCl and NaOH addition. The suspensions were agitated in a shaker for three hours. The final ion concentrations in solution were determined by atomic absorption analysis. The electrokinetic measurements were made using a Komline-Sanderson Zeta Reader in a conventional manner. All experiments were carried out in the presence of 1.0x10-3 k.mol/m3 NaClO4. Experimental results Figure 1 shows the zeta potential of barite particles as a function of pH in the presence of iron(II). The

Jan 1, 1988

By B. M. Eiter

The impact of fatigue is seen not only in its effect on the job performance of haul truck operators but also on the health of the operator and the productivity at the mine site. Its impact can even extend outside of the mine site to the health and well-being of the surrounding community (Fourie et al., 2010). In this paper, a case study of a small, surface mining organization is presented. The goal is to highlight the fatigue risk management system implemented at the studied mine site. Mine safety personnel who were interviewed discuss the changes made to the infrastructure of the mine, to administrative areas such as the number of shifts and the use of vacation time, as well as the implementation of new technology into haulage vehicles. This paper reviews how these changes are supported in the research literature.

By Charles W. Rountree

Industrial Engineering in the industrial world is a relatively new field, having been conceived about the turn' of the century by Frederick W. Taylor, who was not satisfied with the hit-or-miss methods of evaluation and estimation. Through crude Industrial Engineering techniques never before used, he completely changed the bricklaying industry so that work accomplished was more than doubled. To help us better understand what we mean by Industrial Engineering, I think a very simple definition Is in order. Industrial Engineering is a scientific approach to problems in cost, production and operations: and is designed to provide a means of increasing producitivity and reducing costs through standards measurement and standardization of the best methods, practices and equipment, There are many complicated definitions, but pure and simply, it all boils down to providing the means for increasing productivity and reducing the cost. Industrial Engineering has been applied in manufacturing since Frederick W. Taylor?s time and in the last 20 years has grown in stature by leaps and bounds. It is a basic function of successful manufacturing companies and is an accepted fool firmly entrenched in manufacturing organizations. You may know of some successful manufacturing companies that do not employ Industrial Engineers as such, but someone in that organization is doing Industrial Engineering work. They have standards and controls whether they call it Industrial Engineering or not. The manufacturing industry has benefited from this tool; other wise, it would have been discontinued long ago.

Jan 1, 1958

By R. K. Mehta

An accurate, efficient and stable computation of the mill matrix function (eAt) is needed where mill matrix (A) is a real general matrix. Two important modeling cases in comminution where such need arises are: Heterogeneous comminution behavior of multi-component ores and ultra-fine grinding involving simultaneous attrition and fragmentation breakages. This paper presents the application of a novel splitting method in conjunction With similarity transformation technique in the form of "product formula" which is found to work in all cases and uses a most aggravating, yet interesting property of the matrix exponential in a restricted sense. Results are presented showing that this method can yield solution as accurate as those obtained With an analytical technique. The utility of this computational approach is demonstrated by parameter estimation analysis using a distributed component model in the liberation area through computer simulations.

Jan 1, 1992

In 1992, United States mine production of barite decreased 8.5%. Barite consumption, sold or used by grinding plants, decreased by 36.9% and imports decreased by 61.6% vs. 1991. World mine production decreased 1.5%, according to the US Bureau of Mines. The value of domestically produced barite, f.o.b. mine, decreased 11.9% according to the Bureau. The declared value, c.i.f. United States port, of all imported crude barite during 1992 decreased from $42.35/t ($38.42/st) in 1991 to $40.09/t ($36.37/st). Nevada continued to be the leading producer of barite with 88% of the total, followed by Georgia and Missouri. It is estimated that 80% of the domestically mined barite was used as a weighting agent in drilling fluids. The remaining 20% was used in barium chemicals, glass or as a filler. Most of the production from Missouri, Georgia and Ten¬nessee was used in the non-oilfield sector. Of the total barite used by grinding plants and chemical manufacturers, it is estimated that 90% was used in drilling fluids and 10% in the non-oilfield sector. This included barium chemicals and fillers in paper, plastics and glass. The tonnage consumed in the drilling fluids market decreased due to the lower average rig count during 1992. The average number of rotary rigs operating (717) was 16.6% less than the 1991 average of 860 in the United States. Crude barite imports were 518 kt (571,000 st), 61.6% less than in 1991. Imports accounted for 44.7% of the barite consumed (apparent) in the United States. During the year, China continued to be the leading exporter of crude barite ore to the United States with 67.2% of total crude ore imports. India followed with 31 %, and others with 1.8%. About 90% of the imported barite ore was used in the oilfield sector. Ground barite imports decreased from 46.3 kt (51,000 st) to 30.9 kt (34,100

Jan 1, 1993

By William H. Langer

Nearly every community in the United States is dependent on aggregate (sand, gravel, and crushed stone) resources to build and maintain its infrastructure. Unfortunately, developing aggregate resources to meet societal needs causes environmental impacts. Most environmental impacts associated with aggregate mining are benign. Extracting aggregate seldom produces acid mine drainage or other toxic effects commonly associated with mining of metallic or energy resources. The most obvious environmental impact of aggregate mining is the conversion of land use, most likely from undeveloped or agricultural land use, to a hole in the ground. This major impact is accompanied by loss of habitat, noise, dust, blasting effects, erosion, sedimentation, and changes to the visual scene. Some of the impacts are short-lived, and most are easy to predict and easy to observe. Most impacts can be controlled, mitigated, or kept at tolerable levels and can be restricted to the immediate vicinity of the aggregate operation by employing responsible operating practices and available technology. The intensity of environmental impacts generated as a result of mining are determined in large part by the geologic characteristics of aggregate deposits (geomorphology, geometry, and physical and chemical properties). Mining deposits that are too thin, or contain too much unsuitable material, results in the generation of excessively large mined areas and large amounts of waste material. Mining aggregate can lead to serious environmental impacts in some situations. Some geologic environments such as active stream channels, slide-prone areas, and karst terrain are dynamic and respond rapidly to outside stimuli including aggregate mining. Some geomorphic areas and (or) ecosystems underlain with aggregate serve as habitat for rare or endangered species. Similarly, some geomorphic features are themselves rare examples of geologic phenomena or processes. Mining aggregate might be acceptable in some of these areas, but should be conducted only after careful consideration, and then only with extreme prudence. Failure to do so can lead to serious, long-lasting, and irreversible environmental consequences, either in the vicinity of the site or at locations distant from the site. Environmental impacts caused by irresponsible aggregate mining can compromise mining in an entire region.

Jan 1, 2001

By K. L. Hanning

Grinding and classification circuits at Climax Molybdenum Co. are described. Since the installation of a direct digital control computer in 1974, a number of control strategies were developed and evaluated. This paper deals in particular with the practical experience and results obtained in direct digital control of a wet grinding circuit consisting of a ball mill, constant speed sump pump, and hydrocyclones. For this circuit throughput is maximized, while maintaining a desired product size. Product size is inferred from measurement of operating variables.

Jan 1, 1977

By NARAYAN K. BHAGAT, ARVIND K. MISHRA, Aditya Rana, M. M. Singh

The paper presents an innovative directional controlled blasting (DCB) technique for excavating unstable slopes along the Konkan railway in India without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw were developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3, irrespective of the actual free face, was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle was changed from 80–82 to 45–47 degrees, and possible wedge, planar and toppling failures were eliminated. No incident of rockfall and slope failure along these slopes has been observed after the stabilization.

By S. S. Sephton

Sintering as applied to agglomeration of ferrous fines has shown little growth in the United States in recent years. The general concensus was that most of the existing facilities would remain in production at a reduced tonnage to dispose of and recover solid waste from steel plants. Further growth for ferrous sintering technology was not in sight in the United States and in the early sixties expansion came to a virtual standstill, however, we witnessed a rapid emergence of a tremendous pelletizing industry. On other continents, due to different raw materials supply and capital structure, sintering technology continued to grow, with a more cautious development of pelletizing installations. In the U.S. the diminishing supply of good quality, high grade coarse ore resulted in eventual disappearance of high grade ore fines for sintering. The finely divided concentrates produced from lower grade ores were not amenable to this type of agglomeration, but were more suitable for pelletizing. Furthermore, pellets seemed to possess all the features of an ideal blast furnace feed; namely pellets are free flowing, uniform in size, strong, with extremely uniform chemical composition and good reducibility. Importance and demand for such well stabilized furnace feed further increased as size of newly installed blast furnaces continued to grow. The in- creasing demand for a uniform, stabilized burden coincided with the effort to produce a fully beneficiated burden for smelting, thus reverting the blast furnace to its primary function of smelting.

Jan 1, 1973