Search Documents

By J. Y. Kim

Lead ions originating from galena during processing of complex sulphide ores migrate to "cover" the surface of sphalerite and iron sulphide mineral particles, and cause poor selectivity in differential flotation. Generally in sulphide ore processing, the lead-activated minerals float in the Cu/Pb rougher circuit. Subsequently, surface lead complicates the zinc flotation circuit by lowering the concentrate grade due to the co-flotation of lead-activated iron sulphide minerals. The effect of lead in the differential flotation of sphalerite from Cu-Pb-Zn and Pb-Zn ores is discussed. Plant and laboratory test data are interpreted by determining the surface composition of individual grains of sphalerite and iron sulphide particles using two surface analytical techniques, Laser Ionization Mass Spectrometer (LIMS) and Time of Flight-Secondary Ion Mass Spectrometer (TOF-SIMS). Cationic and anionic species on the surface were analyzed to elucidate the phenomena.

Jan 1, 1995

By Giovanni Barla

The stress-relief method for the determination of the ground stress tensor is a common procedure in rock mechanics. In particular, the method of applying gauges to the end of a borehole is a well-established technique. Investigations, both experimental and theoretical, indicate that large discrepancies can exist in the determination of the ground stress tensor when the rock substance is not the ideal elastically isotropic material assumed for the reduction of data. The purpose of this paper is to extend the analysis of strain gauges applied to the end of a borehole to rock material more closely approximate to an orthotropic substance.

Jan 1, 1969

By Erwin K. Roesner

The difficulties encountered while sinking deep shafts for Potash Mines in southern Saskatchewan have been the subject of several papers in the past. Geological and hydrological conditions of the strata overlying the potash deposits require special techniques for ground and water control during shaft sinking. The easily soluble potash ore requires the lining of these shafts to be virtually watertight to assure long term and safe operation. This paper describes the construction of the most recently completed potash shaft for the Potash Corporation of Saskatchewan. The shaft was designed and constructed by Thyssen Mining Construction of Canada Ltd. and it is located near Lanigan, approximately 110 km east of Saskatoon.

Jan 1, 1980

By J. E. Lees

Advanced remote sensing can be a powerful new information tool to help private and public entities make better environmental and resource management decisions. However, some regulated entities are reluctant to develop or use this tool because of their concerns that it will lead to increased risks and costs of environmental legal liability. They fear that new ways of monitoring the environment will increase liability, undermine existing enforcement agreements, reopen compliance agreements, and generally provide a competitive disadvantage to early adopters by accelerating environmental cleanup costs. Others counter that the increased risks are marginal, and that several advantages outweigh these risks, including the opportunity to more effectively manage environmental operations, target and set priorities, measure and track management and compliance effectiveness, provide more defensible environmental assessments and baseline conditions, make and defend optimal siting decisions, and avoid or resolve environmental disputes. This paper offers strategic advice on ways regulated entities can enjoy the benefits of these powerful new information tools while mitigating down-side legal and compliance risks as much as possible.

Jan 1, 1999

By Mark Van Dyke, Mark Mazzella, Gamal Rashed, Nicole Evanek, Brent Slaker

In the past decade, there have been several incidents of massive ground collapses in underground stone mines in the eastern United States. Fortunately, these events have not resulted in any fatalities. However, three mine workers were injured and many others were at risk due to the hazard from the fall of ground and/or the airblast associated with these massive collapses. The National Institute for Occupational Safety and Health (NIOSH) initiated a project to better understand the causes of these massive ground collapses to help prevent their future occurrence. The main objective of this study is to investigate the main factor(s)that initiated one of these massive ground collapses. The authors relied on several tools including three-dimensional (3-D) LiDAR scans for the surface subsidence feature and the underground mine workings around the collapsed area, borescope data at multiple locations around the collapse, S-Pillar analysis for average and unfavorable conditions, and numerical models. The emphasis has been placed on the impact of the following limestone pillar stability parameters: pillar width-to-height (W/H) ratio, benching, the existence of karst features, weak roof, and geological discontinuities. 3-D LiDAR scans were utilized to show the shape and the extent of karst cavities observed within stable pillars around the perimeter of the collapsed area. Together, this coupling of field measurements and observations and modeled systems suggests the potential causes of the collapse.

Jul 1, 2023

By M. L. Mellish

In 1989, for the third consecutive year, both the production and consumption of coal in the United States reached record levels. Domestic coal consumption totaled 806.5 Mt (889 million st) in 1989, a 5.4 Mt (6 million st) increase from the year before (Table 1). US coal exporters also had a banner year. For the first time since 1982, exports ex¬ceeded 91 Mt (100 million st). US coal production in 1989 rose by a surprising 27.3 Mt (30 million st), reaching 889 Mt (980 million st) for the year. To a certain extent, the sizable difference between production and demand growth was due to smaller consumer stock withdrawals. Coal consumers withdrew only 12.7 Mt (14 million st) of coal from their stocks in 1989, com¬pared to 22.7 Mt (25 million st) in 1988. Despite strengthening coal consumption, exports, and production, coal prices to all domestic sectors declined slightly during the year. That essentially continued the trend of the past several years. On the labor front, the United Mine Workers of America struck the Pittston Coal Group in 1989. It was a bitter work stoppage that was not settled until February of 1990. This was the first major coal strike since 1985. The strike also precipitated a series of wildcat outages by UMWA members in June and July. At their peak, more than 40,000 UMWA members participated in the wildcat strikes. Except at Pittston, however, most miners were back to work by August. It is estimated that perhaps 4.5 to 9.1 Mt (5 to 10 million st) of coal production was lost due to the Pittston and associated wildcat strikes. However, some of this production may have been recouped by other coal companies not affected by the wildcat strikes, and by the affected companies after the strikes ended.

Jan 1, 1990

By N. T. Rogers

An accepted statement of fact is that transportation next to agriculture is the second most important industry in the world. The transportation networks of the United States contributed immensely to the growth and prosperity of our nation. My objective is to make each and everyone here aware of the need for communication between geologists, mining engineers, purchasing agents and transportation managers. Only through a cooperative effort is it possible to reap the benefits of transportation in the industrial minerals field. Transportation is often thought of in terms of trucks, rail cars, barges, covered wagons or whatever. If this is your only exposure to the transportation industry then you probably spent most of your life in a cave.

Jan 1, 1989

By Kanaan Hanna, Mir Heydari, Dipack Sengupta, Gordon B. French

This article, first in two, discusses the safety, technology, and economic impact of eliminating safety fuse from metal and nonmetal mines. It is based on operation and manufacturer experience over the past five to 10 years. If safety fuse is eliminated, blasting accidents will decrease. There should be only limited technical impact. The economic impact will be minor for large operations, but will be significant enough for small operations that some will likely close rather than change. Most mines would probably change over, with the market absorbing the extra cost. Elimination of safety fuse would obviously have an impact on the two safety fuse manufacturers. One manufacturer produces an alternative system and would be unaffected. The other, however, will be affected if it does not change its production strategy. From the standpoint of employment and production, abolishing safety fuse will have a very minor effect on the mining industry as a whole. This article discusses the current use of initiation systems, incidence of accidents, and fuse consumption. Next month, part two describes the economic impact of eliminating safety fuse on the mining industry and manufacturers, and presents an economic analysis of the initiation systems. Introduction The objective of this study was to determine the safety, technology, and economics of eliminating safety fuse from metal and non-metal mines. There were five major tasks: • Studying initiation-related accidents from the Health and Safety Accident Center (HSAC) data file; • Visiting mines, collecting relevant data, and interviewing mine operators; • Establishing the trend in safety fuse consumption and type of users; • Corresponding with fuse manufacturers, domestic and foreign; and • Developing an idealized blasting cycle to evaluate the possible economic impact of safety fuse elimination on large and small operations. More than 450 explosives-related accident reports have been screened and analyzed by investigating HSAC files. These reports have been studied and classified according to the four initiation systems, size and type of mines, and time and frequency of accidents from 1973 through 1978. Twenty-four mining operations were visited to obtain supporting data for this study. Mine personnel were interviewed to determine attitudes about safety fuse and alternative detonating systems. This article decribes available data. It also attempts to provide information that can be used to answer such questions as: • Is the use of safety fuse (an antiquated detonation system) a major cause of mining accidents? • Are alternative systems available that could result in fewer in-juries to miners?

Jan 1, 1984

By J. B. Griffiths

Clearly there is a tremendous need for assistance in Eastern Europe since most industries must undergo major restructuring. The new governments face many dilemmas, the first task being to establish an order of priorities to deal with the numerous problems at hand. Issues such as the standard of living take low priority compared with market economy and ecological problems. The concept of a Comecon market is now virtually non-existent and trade in roubles ceased from 1991. From this time onwards countries were obliged to trade using free market prices. Governments must also avoid the economic mistakes of countries such as Poland with its high devaluation and lack of economic control and, if possible, contain inflation and unemployment. The privatization of Eastern European enterprises raises considerable difficulties, particularly for large corporations, employing anywhere from 50-100,000 people, which played a major role in the national economy. Whichever method is selected, however, still has to overcome the problem of lack of capital and evaluating the national property. For example, earnings represent only a small percentage of the value of these national industries and thus cannot convert to private ownership without foreign capital investment, either direct or as joint venture capital.

Jan 1, 1992

By D. E. Hinkle

Past surface-mining operations in Appalachia primarily followed mountain con-tours. It is estimated that about 18,000 mi. of highwalls are exposed throughout Appalachia. An evaluation procedure for determining the secondary mining potential (SMP) of these highwalls has been proposed. Sixteen parameters affecting the SMP were isolated. These are grouped in four major categories: geologic conditions, existing infrastructure, site conditions, and environmental conditions. The parameters were then ranked by their impact on SMP and assigned weighting factors. A simple mathematical procedure yields an SMP number (0 < SMP < 100), which may then be used to compare alternative sites and technologies. Determination of limits and ranges while grouping data was aided by field visits to over 40 exposed highwalls in Eastern Kentucky. An interactive program has been developed to rapidly evaluate the SMP for pre-mined sites. The mathematical procedure estimates the relative potential (i.e., techno-logical feasibility) for remining for three predominant secondary mining methods: augering, Hi-wall mining, and underground mining. Other secondary mining methods are briefly reviewed and compared.

Jan 1, 1989

In this paper, response surface methodology was applied to optimize the experimental conditions for the wet grinding of synthetic rutile. The effects of parameters such as rotation speed, solids concentration and duration of grinding on grinding efficiency were systematically investigated and the process conditions were optimized, using a nonlinear regression model based on central composite design. The statistical analysis of the results showed that in the range studied, the grinding efficiency of synthetic rutile was significantly affected by the rotation speed of the conical ball mill. According to results from analysis of variance, the value of the determination coefficient (R2=0.9989) indicates that the predicted values are found to be in good agreement with experimental values. The optimized experimental conditions were as follows: a rotation speed of 350 rpm, a solids concentration of 27.31% and a grinding time of 50.31 min, respectively. Under optimum conditions, the predicted grinding efficiency of 94.79% is obtained. The experimental values from the validation experiments were well within the predicted value of the model.

Jan 1, 2011

By R. A. Burns

The production of kaolin and calcium carbonate in North America exceeds 13 million tons sold into higher value market segments. With a few exceptions, the markets supplied exhibit mature growth rates. In some market sectors, technology changes have and continue to occur shifting pigment-type consumption and growth. New sources of supply will impact current businesses. New product and process developments for kaolin and calcium carbonates are continuing. Each of these issues is examined in developing a view of the future for kaolin and calcium carbonate in North America.

Jan 1, 1997

By A. A. Campoli

The U. S Bureau of Mines is conducting research to develop improved guidelines for selecting the type and pattern of roof support in different geologic environments (Mucho, et al., 1995). As a part of this wider research effort, a multifaceted ground control investigation was conducted at the Diamond TB Mine of RoxCoal, Inc. The study included statistical analysis of mine-wide roof bolt performance, instrumented bolt test areas, stress damage mapping, and pillar design analysis. The mine employs state-of-the-art continuous miner technology, including mobile roof supports and continuous haulage, to retreat mine the Lower Kittanning Coalbed. A herringbone section design makes the stability of the center belt entry critical to efficient retreat mining. Roof cutters formed during section development sometimes set up unstable immediate roof conditions in advance of the belt entry mobile roof supports during retreat mining.

Jan 1, 1996

By Garry W. Warren

The electrochemical oxidation of chalcopyrite in the absence of-a chemical oxidant was studied in ammonia/ammonium sulfate solutions by anodically polarizing electrodes prepared from massive chalcopyrite. The effects of pH, cupric and ammonia ion concentration were systematically evaluated. Kinetic parameters were obtained from the anodic charge-transfer regions of the anodic polarization curves. Increasing ammonia and hydroxyl ion concentrations increased the rate of oxidation. A mechanism is proposed which explains the first order dependence of (NH3) and (OR) associated with a single electron transfer process. An empirical relationship which accurately describes the dependence of the rest potential (i.e. zero current potential) on solution composition is also given.

Jan 1, 1978

By L. Yan, B. Lambie, J. Srednicki, J. Carr

Electromagnetic emissions from electrical devices may interfere with electronic safety systems or other devices in the mining environment. This electromagnetic interference (EMI) may cause unwanted changes in the performance of the affected devices and may cause safety issues for miners. To minimize the risk of EMI, the National Institute for Occupational Safety and Health (NIOSH) has conducted research quantifying the electromagnetic emissions of several types of equipment that might be used in the mining environment. Previous research has shown that welding arcs can give off ultraviolet (UV) emissions, visible light, and infrared (IR) emissions that can cause health problem on skin and eyes. In this study, the electromagnetic emissions of the shielded metal arc welding (SMAW) process were monitored and measured. Several factors including operating mode (AC, DC positive or DC+, DC negative or DC-), current setting (low, medium, high, maximum), and electrode type were investigated to compare their effect on emission level. The test shows that the emission level from the welding process can be affected by those factors. The test data also shows that, among those factors, the operating mode has more influence on emission level than do current setting and electrode type. The information in this paper can be useful for the mining industry to better understand the emission in the 9-kHz to 500-MHz frequency range from a SMAW welder.

Feb 1, 2023

By G. Wayne Clough

During shallow tunneling in an urban environment, deposits or pockets of saturated soil or fractured, weathered rock are often encountered. Under such conditions, special problems with tunnel support, underpinning of structures adjacent to the tunneling, and/or flow of groundwater into the tunnel occur. If the ground conditions are appropriate, i.e., the soil is sandy, silty or fissured, or the rock is weathered or fractured, the solution to these tunneling problems may be chemical stabilization of the ground. Injection stabilization as an aid to tunneling is practiced extensively in Europe and its use is increasing in the U.S. The advantages of this technique over conventional solutions can be substantial in terms of cost and time, especially in mechanized tunnel boring where even a small zone of soft ground can bring the tunneling to a complete halt. In this paper European practice in using chemical ground stabilization for urban tunneling will be reviewed. In contrast to previous papers which have dealt with specific applications (1,5,8,9) this paper will broadly cover the subject, addressing itself to grouting techniques, costs, the reasons for grouting, philosophy of the users towards grouting, design of grouting solutions (or lack thereof) and methods of quality control. Differences with U.S. grouting practice are also noted. The information presented is derived from several visits to Europe, discussions with European and U.S. grouting personnel, and the available literature (2). The author&apos;s most recent European trip was made under the auspices of the U.S. Department of Transportation in conjunction with a research study being performed at Stanford University; a detailed report of this visit is available in reference (6).

Jan 1, 1976

By K. E. Burgher

Since World War II, the need for the use of explosives in construction, mining, and quarrying near congested urban areas has increased dramatically. Often times a coal mine, once isolated from a city, finds itself surrounded by residential and commercial structures. The United States Bureau of Mines and others have researched blast design to a point where ground vibration and airblast damage can be avoided. A problem still exists, however. It is the fact that people often react to only the loud noise associated with a blast although it may not cause damage. Most often it is the concussion of a blast, less than 20 hertz and inaudible, that produces damage. Public fear from the "startle" and "fright" of loud blast noise greater than 20 hertz leads to the complaints which are generally unfounded. See Thackray, Touchstone, and Baily (1975) for a further discussion of the startle effects of loud sudden noises. When blasts are designed in accordance with U.S.B.M. specifications, management generally has little to worry about with respect to damage claims. Complaints, however, still arise when the noise is accentuated from the blast. It is meteorological conditions which dictate how the sound levels will propagate. Some mines use small pilot test shots (generally one-two lbs) to determine when atmospheric conditions favor sound travel.

Jan 1, 1987

By Liming Yuan, Isaac Zlochower, RICHARD THOMAS, Thomas H. Dubaniewicz, Teresa Barone

Mining vehicle manufacturers are developing lithium-ion (Li-ion) battery electric vehicles as an alternative to diesel-powered vehicles. In gassy underground mines, explosion-proof enclosures are commonly used to enclose electrical ignition sources to prevent propagation of an internal methane (CH4)-air explosion to a surrounding explosive atmosphere. Li-ion batteries can create pressurized explosions within sealed enclosures due to thermal runaway. Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) measured thermal-runaway pressures of lithium iron phosphate (LFP) cells as a function of free space within sealed enclosures and observed an inverse power relationship. A well-confined cell produced 4260 psia (294 bar) of pressure during a thermal runaway, far exceeding minimum pressure containment specifications for conventional explosion-proof enclosures. Results indicate that adding enough free space surrounding LFP cells can reduce thermal-runaway pressures to levels below that expected for CH4-air ignitions. Measured thermal-runaway temperatures were below the minimum autoignition temperature of CH4-air.

By A. K. Bakshi

Slurry rheology affects autogenous grinding performance by changing the rock&apos;s breakage characteristics. In this study pilot scale batch autogenous grinding was carried out to observe the effect of viscosity on the breakage characteristics of the rocks (the media), and on the overall specific energy consumption. Clay/fines content, and temperature of the initial charge, were varied to alter the viscosity of the slurry. Results showed that at higher slurry viscosity, rocks became more difficult to break, resulting in an overall increase in the specific energy consumption of the mill. Also, it was observed that viscosity had a significant effect on the amount of critical size material present in the grinding circuit, where the critical size material is the material which is too large to be effectively ground in the mill, and too fine to act as grinding media.

Jan 1, 1996

By E. W. Sawyer

Gelling-grade attapulgite and sepiolite clays are employed as thickening agents for the preparation of ionically contaminated drilling fluids where the use of fresh water clays are unfeasible or impossible. Attapulgite and sepiolite are nonswelling clays that can be dispersed and reflocculated by mechanical and chemical means to increase the viscosity of fresh water, salt containing waters, gypsum contaminated waters and fluids containing cement. Such gelled systems are quite stable in viscosity properties and can be further treated with other necessary additives such as thinners, water loss reducers, weighting agents, surfactants, etc. Many of the oil well drilling fluid practices have influenced such technologies as water well drilling, foundation drilling and waste disposal. The use of salt water gelling clays in these fields will be described and compared to oil well drilling.

Jan 1, 1986