Search Documents

By Jack E. Thompson

Thank you Tom and JM for that nice introduction. The remarks I am about to make rely on a large way on comments made by Barrick's Chief Counsel, Patrick Garver, to an internal meeting of Barrick's senior staff. I plagiarized so much from his notes that I thought that I should provide attribution. I did get his consent to borrow so freely. What I have done is take his general comments and used my conversations with CEO's and other participants in the industry to enhance the message with concrete examples that underscore the points I wish to make. What you are about to hear is my personal view – I am not speaking as a representative of any company. With that introduction, now would be a good time to give you the main theme of my talk: The SEC should change its rule making to a more public cooperative approach. If that were to happen the SEC would avoid some of the harm it has been doing to the companies in this sector and the very shareholders it seeks to protect.

Jan 1, 2003

By B. T. Stanley

Traditional methods of creating a water tight shaft liner involve the use of segmented or welded steel. When shafts are located in ground that exhibits extremely difficult conditions of high water inflow and hydraulic pressure, composite liners are often combined with ground freezing during construction. The authors were searching for a cost effective and more flexible solution to hydrostatic liners design than the traditional concrete/steel composite design used so far. Searching through new technologies developed for tunneling applications, sprayed on membranes systems seemed very promising but were not developed for the specific circumstances encountered in shaft sinking applications where ground freezing is involved. Even though freezing is a very effective technique, it creates adverse temperature conditions for the application of spray on membranes. In addition, application and hydrating cure times for those membranes products ranged between six to twenty-four hours under ideal conditions (usually temperatures well above freezing point), which eliminated them from consideration in a shaft sinking cycle. While researching different spray on membrane materials, it was discovered that Stirling Lloyd Polychem Ltd. has developed and proven a different membrane material for waterproofing liners in different tunneling applications. The characteristics of the membrane exceeds the pressure parameters encountered in frozen shaft sinking operations, and the chemical cure times were reduced to one hour per layer which worked well into the shaft sinking cycle times. More over their system included a quality control procedure that allowed insuring integrity of the membrane at application time, a very desirable feature for shaft liner construction. However, the frozen rock surface still presented an unknown in the cure time and stability equation. As all membrane products a shotcrete substrate is usually required prior to application. The hypothesis used by the author was to use this shotcrete layer, not only as a substrate, but also as a thermal insulation against the frozen rock and the membrane during both application and curing time. The authors knew from experience that shotcrete could be applied successfully over frozen rock. But the shotcrete temperature curve over time was unknown and no information were found in the available literature. Testing was required to determine whether a suitable mix of shotcrete could be applied to the frozen shaft wall to provide enough heat of hydration for a suitable period of time to create conditions suitable for membrane application and curing.

Jan 1, 2012

By C. Garcia, C. L. Lin

Characterization and analysis of multiphase particles and/or particulate systems (such as the packed particle bed) are of great technological importance for mineral processing applications. In general the performance of these applications depends on the statistical characteristics of particle microstructures, such as composition distribution, surface exposure of mineral grains, pore network structure, etc. For continued technological progress in the field of multiphase particulate processes, the need for quantitative spatial analysis of multiphase particles in three dimensions has increased sign6cantly. Such quantitative information must be accurate enough that the measured values can be used as parameters for simulation models, process design procedures, and control strategies. Modern 3D image-acquisition techniques, such as X-ray microtomography (XMT), offer a unique imaging capability that can produce high-resolution (a few micrometers) three-dimensional images of the internal structure of multiphase particulate samples. These three-dimensional image data present new challenges for image analysis, image processing, and visualization. Furthermore, important issues should focus on how to use the 3D information and derive new insights into the improvement, design, and operation of mineral processing processes. In this paper, utilization of XMT for characterization and analysis of leaching process involving multiphase particulate system is discussed.

Jan 1, 2005

By G. Bylapudi, A. Bhagwat, K. Mondal, A. J. S. (Sam) Spearing

Minimizing the effects of corrosion improves the long-term performance of the rock anchors and ground control systems in underground mines, which is fundamental for safe operation over the design period. The primary objective of this study is to explain the problems due to stress corrosion cracking (SCC), strain-induced corrosion cracking (SICC) and other forms of corrosion, and why the mining industry’s ground control professionals should take this into serious consideration. It is important to clearly determine the kind of SCC mechanisms that causes roof bolt failures in order to suggest the necessary action plan to mitigate or eliminate the possibility of the cause. Pertinent literature and studies around the globe on this complicated subject are reviewed. The secondary objective is to encourage the use of corrosion-resistant ground control products in the underground mining industry in areas of high corrosion potential. Characteristics of SCC on high strength steel are also reviewed. The literature and preliminary studies to date indicate that research work is necessary in United States.

Jan 1, 2015

By G. Vallebuona

Currently, empirical models are used for predicting the hydrocyclone performance in terms of capacity, cut size (d50,c), water split and partition curve. These models, for example those of Lynch and Plitt, have been developed and checked for hydro cyclones with diameters larger than four inches. For smaller diameter hydrocyclones little empirical modelling has been done. This paper reports extended experimental research on small hydrocyclones. For these cyclones, the suitability of existing empirical models has been checked and their accuracy compared. Modifications of the existing models equations are proposed, improving their predictive capability for the small cyclones performance.

Jan 1, 1994

By d&apos, L. F. G. Assumpcao

Kaolin samples from Rio Capim resources were treated in conventional and superconducting magnetic separators to study the main variables that influence the color removal process. Coating clays and delaminated clay were tested. Retention time (or pulp injection velocity), magnetic field intensity and matrix type were the' variables studied. The feed brightness ranged from 84.7 to 87.6 % ISO for the coating clays and from 80.7 to 85.4 % ISO for the delaminated clay. The results showed unleached brightness values higher than 88 % ISO for coating products and higher than 87 % ISO for the delaminated product, using a conventional magnetic separator with an applied field of 1.5 to 2.0 Tesla. With a maximum field intensity in the superconducting machine of 5.0 Tesla, unleached brightness values higher than 88.5 % ISO for both coating and delaminated clays were attained.

Jan 1, 1995

By J. Wesley Atkins

In considering the importance of lease management and administration, I have decided to approach the topic, Lease Default and Eviction: Action or Reaction, as a three phase presentation dealing with mineral lease administration and management, past, present and future. Though the title may border on the dramatic, it illustrates the real consequences of alternative approaches to property management viewed from my experience in the evaluation, development and implementation of a number of such systems and services in my current position as president of Talco Group Corporation. First, though, let's take a moment and set the stage by giving a few actual examples of why a pragmatic approach is needed in this particular area.

Jan 1, 1983

By Chester O. Ensign

The White Pine Mine is situated in the southwestern portion of the Keweenaw Peninsula of Upper Michigan approximately 6 miles south of Lake Superior (Fig. 1). It is east of the Porcupine Mountains in Ontonagon County. The ore deposit is about 70 miles southwest of the famous native copper deposits of the "Copper Country" lying northeast of Houghton. Geological conditions are different at every mine and create a special set of problems in dilution control. This paper is largely intended to describe the techniques applied in mine dilution control (grade control) at White Pine, and present results of the program. For necessary background information major geologic characteristics of the deposit, particularly those that exert control over the distribution of ore, are briefly discussed. Mining methods are described in considerable detail since applied grade control techniques are adapted to these.

Jan 1, 1964

By C. W. Baxter

Eveleth taconite company was formed in 1963 to mine and beneficiate taconite on the Mesabi range of Minnesota. Its thunderbird mine is located midway between the cities of Eveleth and Virginia, Minnesota, and the crude ore is transported by rail to its Fairlane plant approximately ten miles to the south of the mine, "figure 1". As is implied by the names of the mine and plant, the ford motor company is the principal owner of Eveleth taconite company, with an 85% interest, Oglebay Norton company holds the remaining 15% interest and also is the managing agent.

Jan 1, 1972

By J. M. King

A crucial step in the acquisition by one company of the assets of another, the acquisition of the stock of another company, or the merger of two com-ponies, is the legal due diligence which needs to be performed in order for the acquirer to ascertain or confirm the obligations, liabilities and exposures to risk that are being assumed along with the assets or corporate stock being acquired. Where the obligations, liabilities, or exposures to risk arise from existing contracts, or from pending lawsuits, administrative proceedings, or threats of these actions, those matters are relatively straightforward to discover by careful review of the files of the party whose assets or stock is being acquired. However, where a company is engaged in ongoing mining or processing operations and has operated or owned mining proper-. ties, there are many sources of liability and exposure to risk which could have major adverse economic consequences to the acquiring party and which are not revealed, or at least are not clearly delineated, by the records of the company whose stock or assets are being acquired.

Jan 1, 1990

By A. W. Khair

In 1985, an extensive longwall mining research project was initiated by the West Virginia University Research Center entitled "An Improved Longwall Mining Technique" with the purpose of providing operational guidelines for the mining industry to enable efficient operation of its existing and projected longwall installations. One task involved in this extensive research project was monitoring ground movements due to longwall mining and evaluating their impact on surface and subsurface structures. This paper presents an analysis of the effects of topography on quasi-static and dynamic ground movements and the severity of damage inflicted on surface structures. The site was chosen for the study with an attempt to obtain a representative account of the topography experienced in the Northern Appalachian region, and more importantly to contain a substantial number of varying topographical features i.e., mountains, hillsides, valleys, and flat bottom land. The study was made possible by typical subsidence monitoring technqiues, however subsidence monuments were surveyed on a frequent basis, intermittently during face advancement. Ground movements were investigated under both quasi-static and dynamic conditions. This provided insight into the propagation of subsidence and the dynamic affects it has upon surface structures.

Jan 1, 1987

By Ditend Tesh, Godfrey Dzinomwa, Harmony K. Musiyarira

Namibia is known as water stressed country with a limited amount of fresh water. Therefore, the use of water is an important topic in the country’s development agenda. Water is a shared and finite resource, with high social, cultural, environmental and economic value. However, freshwater resources are under pressure from ore processing, industrialization, urbanization and the demands of a growing population. In Namibia, ore processing, coupled with the anticipated increase in water demand for human consumption and other uses, has created significant stress on the limited water resources of the country. This is critical in the mining industry as water remains typically the prime environmental medium (besides air) that is affected by mining activities. This study sought to investigate the strides made in water management in mining, especially in environmentally sensitive areas of Namibia. Most mining companies operate next or alongside farms, national parks and fishing areas. The overall objective of this research was to highlight the current practices in Namibia’s mineral industry operating in environmentally sensitive areas especially in areas where uranium is being mined and processed. The methodology consisted of comprehensive literature review, field visits to the case study areas, and comparative studies with best practices. This study shows that over a ten-year period, freshwater consumption was reduced by over 55% per tonne of milled ore in uranium mines, resulting in substantive financial savings as well as the delay in water augmentation through desalination. The strategies employed by the Namibian companies involve inclusive stakeholders’ engagement, recycling and reuse, and the minimization of water losses. The realization that the water challenge cannot be solved by any one party acting alone has been fundamental in ensuring environmental compliance within the mining industry in Namibia. Namibia’s industrial leaders have increasingly recognized that reducing the water footprint of mining activities must be one of the key performance indicators for management. The major finding of this study was that Namibia with its unique ecosystems, mineral reserves, and emerging industries can harness a wide range of resources both to improve the welfare of its citizens and to protect the integrity of its environment.

Jan 1, 2017

By Jacob Carr, Christopher C. Jobes, Chenming Zhou, LaTasha R. Swanson, Jennica Bellanca, Jingcheng Li

Magnetic proximity detection systems (PDSs) are used with continuous mining machines (CMMs) to protect miners from striking and pinning accidents. Generators are used in a PDS to create magnetic fields covering the space around a CMM. The PDS determines the proximity of a miner relative to the CMM based on the magnetic flux density detected by a miner-wearable component (MWC) and simultaneously alerts the miner and stops the motion of the CMM if the miner is within a proximity that creates a striking hazard. A stable magnetic field is essential to the accuracy of the proximity calculations performed by the PDS. This paper presents the results of a systematic study of the magnetic influence of two types of steel structures found near a CMM— the body of the CMM itself and the wire mesh used for roof and rib control. The results show that the steel of the CMM body can change the magnetic field distribution and also alter electrical parameters of a PDS by changing its generator current. The study also shows that, depending on the distance between the wire mesh and a generator, the magnetic field can also be altered.

By Raymond E. Zimmerman

The use of standard dense-media cyclones is well known, as they have been in use for many years. They are especially well suited for operating at low separating densities and for treating difficult coals containing a high percentage of near-gravity at the point of separation. Very few modifications of the basic design have ever been made. The author recently, however, has been interested in the development of a new type of dense-media cyclone that has been produced in Japan. He has observed the testing of this unit and has collected much data which he feels should be of considerable interest to coal preparation engineers. He feels that this unit, called the Swirl Cyclone, may be of substantial value as an alternate to the standard cyclones. It is certainly worthy of further investigation. There has been relatively little written in English-language publications on the Swirl Cyclone. It was briefly described at the Fifth International Coal Preparation Congress. I It has been described in a general manner by the author in two prior publications. 2, 3 This paper proposes to describe this device in more detail and at the same time submit technical data illustrating its wide characteristics.

Jan 1, 1977

By P. Semberg, B. Bjorkman, C. Andersson

"In this study, the interaction between magnetite and the additive olivine was studied after oxidation as well as after isothermal reduction at temperatures in the 500º-1,300º C range. In the olivine sample, the forsteritic olivine particles react partly during the oxidation pretreatment to form magnesioferrite and vitreous silica along the particle corona. This breakdown of the olivine particles during oxidation liberates magnesium from the particles, which do not react until temperatures of above 1,150° C in reducing atmosphere. When the hematite in the sample is reduced, and when the temperature is high enough to allow solid-state diffusion at ~800º C, the magnesium of the magnesioferrite redistributes, so that the magnesium concentration approaches the same level throughout the iron oxide structure. For magnetite, this did not occur until 800° C. At 1,000° C, this magnesium reacts further with the silica in the glassy slag phase, which crystallizes into fayalitic olivine. At this temperature, the magnesium has diffused over distances of more than 600 µm from large olivine particles after 2 hrs reduction. From this point, the primary slag phase in the pellet, until melting, is solid fayalite. Upon reduction to metal, the metallization front concentrates the MgO in the remaining wustite, which can lead to MgO levels of up to 10 mole% locally. The melting point of the fayalite is raised from 1,145º C to a melting range of 1,238-1,264º C due to the MgO increase, as estimated based on phase diagrams, which were adapted to the pellets tested. Much of the olivine that remained unaltered in the oxidation process will be encapsulated by iron before the particles begin to dissolve in reducing conditions and, therefore, plays no role in the reduction before final melting of the particles occurs.IntroductionEnvironmental concerns have placed increasing pressure on the CO2-intensive iron and steel industries to further optimize operation toward higher productivity and more efficient use of reducing agents. At the same time, high demand for iron ore has caused new iron ores with lower grades and more complex chemistries to be taken into production. In Scandinavia, the main iron-bearing material is magnetite-based pellets with olivine, which allow operation with very low slag volumes and, hence, lower fuel rate ( Slagnes and Sundqvist Ökvist, 2008; Hallin et al., 1994). Both the MgO and SiO2 of the olivine, as well as the elements of the gangue of the ore, i.e., Si, Mg, Ca, Al and alkali, interact with the iron oxides to give the finished pellet product its final properties in the blast furnace. Tailoring the additive mix to be used for a certain iron ore for optimal product properties, therefore, requires detailed knowledge of the mechanisms by which these elements dissolve and react in the pellet."

Jan 1, 2015

By C. C. Clark

The National Institute for Occupational Safety and Health (NIOSH), Ground Control Engineering Branch is investigating the use of shotcrete in weak rock mass mines with the objective of reducing fatalities and injuries resulting from rock fall accidents. When shotcrete is used as part of a multi-element ground support system there is a need to know when the material has developed a threshold early compressive strength of approximately 1 MPa (145 psi) for safe re-entry of miner and machine into shotcreted mine workings. This equates to the material having developed enough strength to be self-supporting and allow for emplacement of the remaining support elements that require drilling of the shotcrete layer without degradation. NIOSH researchers have developed methods and portable test equipment to measure shotcrete strength on-site in the first six hours after application using the ASTM C 116-90 (1990) standard. These advances were demonstrated in tests on five commercially available shotcrete mixes, sprayed as dry shotcrete using the field expedient methods and equipment. The strength values from these tests allowed for real-time identification of the early strength threshold and were consistent with strengths reported using laboratory-type equipment. The findings of this NIOSH research for determining shotcrete early strength can improve mine safety by providing a method for determining initial site specific material property values to be used for design and as a means to conduct on-site quality control and monitoring during production.

Jan 1, 2010

By R. K. Zipf

Recent scientific studies by researchers at the National Institute for Occupational Safety and Health (NIOSH) and the U.S. Army Corps of Engineers (USACE) presented the worst-case explosion pressures that can develop if a methane-air mixture of a certain composition and dimension accumulates and ignites within a sealed area of a mine. The Mine Safety and Health Administration (MSHA) issued its final rule on sealing of abandoned areas which considers potential explosion pressures and the risk of achieving the necessary conditions. The new MSHA seals regulation has increased the pressure design criteria an order of magnitude beyond the old standard of 140 kPa (20 psi) to 800 kPa (120 psi). However, there still are major knowledge gaps pertaining to seals and sealed areas including: (1) the composition of the sealed area atmosphere and how it changes in time and space, (2) explosion pressures that might actually develop within sealed areas, (3) engineering procedures to follow when designing seals and seal installations, and (4) guidelines to manage the atmosphere within sealed areas with monitoring or inertization. NIOSH has initiated a seals research program with collaborators from Safety in Mines Testing and Research Station (SIMTARS) in Australia, West Virginia University (WVU), the Naval Research Laboratory (NRL), and USACE. Highlights of progress so far include: (1) construction of a gas explosion tube at Lake Lynn Laboratory for studying large methane-air explosions, (2) computer simulation of the fluid dynamics of high pressure methane-air explosions, (3) development of seal analysis methods considering construction materials, reinforcement and the seal foundation, and (4) development and testing of innovative seal designs that utilize inexpensive, readily-available rock rubble to resist high explosion pressures. NIOSH researchers aim to provide sound engineering guidelines to better address the new MSHA seal regulations. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

The nature of adsorbed calcium carboxylates (oleate and stearate) has been investigated by in-situ/ex-situ Fourier transform infrared internal reflection spectroscopy (FTIR/IRS). Previous spectroscopic studies in alkaline solution have shown that adsorbed carboxylate is characterized by a C-O stretching vibration at about 1550 em?1 for less than monolayer coverage. Similar results were found in this study. More specifically, in this study such a singlet at 1550 cm-1 was found for LB monolayers of calcium distearate transferred as a condensed layer at a high film pressure to the surfaces of fluorite and germanium. Normally the spectrum of bulk calcium distearate reveals a doublet at 1575 and 1540 cm-1, characteristic of a three dimensional 7-fold coordination for calcium carboxylate complexes. This doublet is generally found for carboxylate multilayers formed by spontaneous adsorption at the surface of calcium minerals. In this regard, the spectral evidence suggests that whenever the calcium dicarboxylate is constrained at a surface as a condensed layer, the 7-fold coordination can not be satisfied and the surface carboxylate is forced into a two dimensional symmetrical coordination with a singlet at 1550 cm-1. On the other hand, if the Langmuir-Blodgett (LB) monolayer calcium distearate film is transferred at a low film pressure the doublet is observed. This analysis is further confirmed by the spectral results for LB transferred calcium distearate monolayers at a hydrophobic silicon surface. Even though these are condensed monolayers formed at high film pressure, the carboxylate group, oriented away from the surface, is no longer constrained by the surface force field, and thus exhibits the characteristic doublet of the bulk calcium distearate salt.

Jan 1, 1998

By A. M. Marabini

Flotation of rutile with N-benzoyl-N-phenyl-hydroxylamine (N-BPHA) has been investigated. Initially, floatability tests were performed in a Hallimond tube. The results indicated that rutile was floatable in the pH range from 2 to 4 at N-BPHA concentration between 2x10-3 M and 2x10-2 M. Selectivity against hematite was recognized when operating at pH values below 2. Following the hypothesis of the formation of a surface chelate between N-BPHA and titanium ion, this compound was precipitated from a solution of Ti(SO4) to which N-BPHA was added. I.R. spectrometry oft the rutile before and after treatment with N-BPHA solution confirmed the presence on the rutile surface of the same compound. The absorption isotherm and kinetics were determined by analyzing N-BPHA in solution with an U.V. technique. A hypothesis for the mechanism of adsorption of N-BPHA on rutile is suggested.

Jan 1, 1982

By K. A. Natarajan, M. R. Sabari Prakasan

"Biodegradation of sodium isopropyl xanthate using two types of bacterial strains, Paenibacillus polymyxa and Pseudomonas putida, is demonstrated. At concentrations higher than 50 mg/L, the presence of xanthate in the growth medium resulted in bacterial toxicity, retarding growth kinetics. Adaptation through serial subculturing in the presence of higher xanthate concentrations resulted in the development of xanthate-tolerant bacterial strains. Stress proteins secreted by bacterial cells grown in the presence of xanthate were isolated. Bacterial cells could utilize xanthate as a growth substrate, degrading xanthate species in the process. Acidic metabolic products generated by bacterial metabolism promoted efficient xanthate decomposition. Probable mechanisms for the biodegradation of isopropyl xanthate are illustrated.IntroductionDifferent types of alkyl xanthates (ethyl, isopropyl, amyl, etc.) have been used as flotation collectors in the concentration of sulfidic ores for several decades. Large quantities of waste water and xanthate-containing effluents are generated by ore flotation processes, posing considerable environmental challenges. Billions of cubic meters of such process waste waters are produced annually across the world, most of which are discharged to the environment, often without any treatment. Leakages and accidental release of xanthate reagents from manufacturing plants and during transportation and storage can also contaminate the environment. Residual concentrations of xanthate reagents are encountered in waste effluent, which are found to be toxic to aquatic life and unfit for human consumption (Harris, 1984; Okibe and Johnson, 2002). Further, direct recycling of such waste waters for plant operations can compromise water quality standards required for process operations. The presence of residual xanthate in recycled waters from flotation plants deleteriously influences flotation processes. Xanthate can be easily decomposed at low pH values; however, CS2, which is more toxic, will be produced by the acidification of neutral and mildly alkaline xanthate-containing solutions. Physico-chemical methods such as flocculation, chemical oxidation and decomposition and physical adsorption used to remove residual collector reagents from mill process waters are often expensive and not environment-friendly (Oliveira and Rubio, 2009; Cheng et al., 2012; Molina et al., 2013,)."

Jan 1, 2015