Search Documents

By III Feeley

Coal is the nation's most abundant fossil energy resource and serves as the primary fuel for the U.S. electric-power industry. However, its continued and expanded use is often challenged by the nature and amount of its associated impurities, such as mineral matter, sulfur, and trace elements. The moderate- to high-sulfur content of many U.S. coals is of particular concern today as potentially more stringent regulations requiring further reductions in sulfur dioxide emissions are being considered. The most prevalent method currently employed to control SO2 emissions from coal-burning facilities is post-combustion flue-gas desulfurization. However, physical coal cleaning (a.k.a. beneficiation, preparation) methods can also be effective in removing sulfur and ash impurities from coal prior to combustion. In a typical physical cleaning operation, raw coal is crushed to about 50-mm (2-inch) topsize, and then screened into coarse, intermediate, and fine size fractions. Crushing liberates some of the ash-forming minerals, including the portion of inorganic sulfur (pyritic) not chemically bound to the coal matrix. The percentage of impurities liberated generally increases as the coal particle size is reduced. Coarse- and intermediate-sized coal particles are typically subjected to specific gravity-based cleaning methods, while fine-sized (less than 0.5-mm) coal particles are beneficiated using froth flotation, a technique based on surface property differences. Greater cleaning potential exists at finer sizes because of increased liberation of impurities, but this potential is not fully realized because of inefficiencies associated with fine particle separation using state-of-the-art coal cleaning technologies.

Jan 1, 1990

By Paul S. Murphy, Eric W. Oehrke

INTRODUCTION The global market for sulphur has experienced dramatic structural shifts during the past 10-15 years. After a number of years of dominance as sulphur suppliers, the world's Frasch producers were confronted with large increases in nondiscretionary sulphur production from sour crude oil and gas, while escalating energy and exploration costs reduced the economic incentives to replace dwindling sulphur reserves. Sulphur demand also experienced substantial growth, but the majority of this increase was filled by nondiscretionary production. The result was essentially flat demand for Frasch sulphur during this period. This paper briefly summarizes Freeport Sulphur Company's outlook for global supply and demand for sulphur through the year 2000, and examines in more detail the history and anticipated shifts in trade patterns. World trade in elemental sulphur (brimstone), despite year-to-year fluctuations, has been on an upward trend in recent years, and should continue to grow through the end of this century. The type (discretionary vs. nondiscretionary) and location of forecast sulphur supply sources has potentially broad implications for the world's Frasch producers, as they compete in a world market which is increasingly supplied by non-discretionary production. SULPHUR DEMAND Sulphur is a versatile and essential element used in a wide variety of manufacturing processes. Almost 90% of world sulphur consumption is in the form of sulphuric acid. The relatively low cost, ready availability, and physical and chemical properties of sulphuric acid make it the most economical acid for a number of chemical processes. Although sulphur is used in the manufacture of many products, the largest consumer by far is the phosphate fertilizer industry. The majority of sulphur demand growth over the past 30 years has occurred in this area, and today it accounts for nearly 65% of global sulphur consumption in all forms. Due to the relative importance of phosphate fertilizers, sulphur demand is typically discussed in terms of fertilizer and non-fertilizer (or industrial) uses, and this approach will be followed here. We at Freeport believe that global consumption of phosphate fertilizers should grow at an average annual rate of about 3.5% through the year 2000, which is roughly equal to the growth rate experienced during the past ten years. The basic assumption underlying this forecast is that world population will continue to grow significantly, while the total acres of cropland will grow only slightly. Therefore, in order to feed a growing population, higher crop yields will be necessary, which in turn will require the increasing use of fertilizers. This expected growth in phosphate consumption will, without doubt, fluctuate from year to year, and we Frasch producers have painful memories of the large dip in demand during 1982-83. However, we believe that the fundamentals for growth are very good, and that future demand will move back onto the historical trend line. In the recent recession the use of sulphur in the non-fertilizer or industrial sector dropped sharply, and it now appears that future growth will not return to the old trend line. Most of the non-fertilizer uses of sulphur and sulphuric acid involve older industries which are very mature, such as oil refining, steel, pulp and paper, pigments, etc. The use of sulphur in some of these industries is expected to exhibit little or possibly even negative

Jan 1, 1986

By Benno Ring

"When designing segmental lining at a cross passage, modern solutions try to bear the loads transferred around the opening within the rings by using shear elements in the ring joints. Commonly used shear systems providing coupling are cam & pocket, shear keys, bicones and steel dowels. These solutions have advantages and disadvantages, but most importantly they have limits in their capacity to stabilize the lining at cross passages. With the help of 3D-FE-analyses for an opening of one segmental ring these different solutions are compared taking various ground conditions into account. As a result the capacity of the individual system is determined. Notice is made regarding the applicability of the system as well as the consequences for the design and the verification. INTRODUCTION The design of the lining at a cross passage is among the most difficult tasks when designing TBM-tunnels. At one time the bedding of the lining disappears due to the excavation behind the lining, at another the ring-structure is interrupted when parts of the lining are removed for the opening. The trick is to transfer the loads around the opening into other segments and to areas of the lining which are still supported by the ground. In the rings immediately at the cross passage this creates a distribution of forces within the segments that strongly deviates from that of the regular lining. The design needs to consider the boundary conditions of the respectively chosen solution for stiffening of the opening and its peculiarities in the modeling as well as in the verifications. In the past segments of steel or an internal strutting of steel (DAUB 2013) placed around the later openings were commonly used, see Figure 1. The application of a strutting from the outside to the rings is restricted to such circumstances when for example a connection from a shaft to the tunnel can be made in suitable ground conditions (Ring and Glomp 2012). Though steel segments provide a robust solution, they are expensive due to their laborious manufacture, the high proportion of construction steel required and the time consuming installation in the tunnel (Häfliger 2013). A strutting of steel requires extensive design and verification. The resulting structure usually weighs several tons and must be erected as well as demounted within the confined space of the tunnel, requiring suitable transport and assembly equipment. The cross section remains restricted, thus causing a bottleneck for TBM operations and hindering the works and installations for the cross passage works."

Jan 1, 2016

By R. Sandrik

Northwestern Resources Co. (NWR) was established in 1972 as a wholly-owned subsidiary of Western Energy Company of Butte, Montana, to acquire, explore, develop, and produce energy resources outside the state of Montana. Western Energy is a coal mining company with successful operations in Montana and Wyoming. In 1974, NWR acquired its first lignite lease in Texas. NWR eventually acquired a large leasehold in central Texas, which was identified as having a high potential for future production. In 1979. NWR contracted to supply lignite to Utility Fuels, Inc. (UFI), a fuel affiliate of Houston Lighting and Power Company (HL&P). This project, together with leases held by UFI, became the Jewett Mine. Lignite from the Jewett Mine is used as fuel at the adjacent HL&P Limestone Electric Generating Station, at an annual rate of approximately 7.3 Gkg (eight (8) million tons) per year.

Jan 1, 1991

By Paul H. Johnson

Heap leaching is a simple means of recovering copper from oxide and oxide-sulfide ores. Although this method requires relatively low capital investment, it suffers from low copper recoveries and relatively high acid consumption. The objectives of this study were (1) to determine what factors influence these shortcomings, and (2) to establish a basis of correlation. between laboratory and field testing. The principal methods of leaching copper ores at the present time are heap, dump, in-place, and vat. A number of references are presented in the bibliography on the theoretical and practical aspects of these methods. In the heap-leaching method, crushed or uncrushed oxidized copper ore is placed on a prepared drainage pad. Acid leach solutions are dis¬tributed over the top of the heap, caused to percolate downward through the ore bed by gravity, and are drained from its base. The leach duration is generally a matter of a few months. Dump leaching is used to recover copper from very low-grade oxide-sulfide pit-waste materials. Here again, leach solutions are, percolated downward through a heap. However, in this method, little or no acid is added to the leach liquors, prepared drainage pads are not used and the leaching cycle is generally measured in terms of several years. Leaching agents are usually autogenously generated by the breakdown of sulfide minerals within the dump.

Jan 1, 1970

By C. N. Greene

I am sure it is obvious to all of you that a complete program of casualty and property insurance is as necessary for any tunneling contractor as it is for anyone else involved in trade in the United States today. Going beyond those general undefined terms, there are many areas that need specific attention, particularly for contractors, regardless of size. WORKERS' COMPENSATION Workers' Compensation is mandatory in all states and the District of Columbia. In most of the states, private insurance provides this coverage. In a few states, the state operates Workers' Compensation funds, some of which are competitive with the private sector and others are operated on a monopolistic basis. Under a monopolistic setup, you have no choice, you must buy coverage from the state. Self insurance of the Workers' Compensation risk is also an alternative in most jurisdictions. With a contractor operating only in the U.S., the coverage extensions are few in number. If your work brings you anywhere near navigable waterways or land extensions thereof, you should have both U. S. Longshoreman and Harborworkers' coverage, as well as Employer's Liability coverage for the master or members of the crew of a vessel.

Jan 1, 1983

By Julián Ortiz C., Clayton V. Deutsch

Indicator simulation allows specification of different continuity of high and low values through the use of grade thresholds. The sequential implementation of indicator simulation has been widely used, but the problem of order relation deviations remains a significant drawback. A new procedure for "Hierarchical Indicator Simulation" is introduced that avoids order relations and offers greater flexibility than the conventional sequential approach. The new implementation simulates all locations at the largest threshold and then considers decreasing thresholds in turn. All nodes with grades that are above the previous threshold are excluded from the domain of the current threshold and therefore, they are not used as conditioning data. The probability of being above or below the threshold is calculated using simple indicator kriging using all conditioning data in the domain, thus the covariance structure is preserved. The theoretical framework of this new approach is fully developed. Practical implementation details are discussed. Application to a copper deposit shows the advantages and drawbacks of the method. Finally, the possibility of incorporating multiple-point statistics is discussed.

Jan 1, 2002

By D. C. Lynch

While silica ores are generally considered to have little value, those with exceptionally low B and P content have, potentially, significant worth if processed for use in photovoltaics. The sales value of a cubic meter of ?run of the mill? silica sand is $42 per cubic meter (retail and delivered). If the silica sand can be used to produce solar silicon, its value after processing is $34,000 per cubic meter. Factors that impact the suitability of silica for direct processing in production of photovoltaics are examined.

Jan 1, 2010

By Alper Kirmaci, Taghi Sherizadeh, Dogukan Guner, Cameron Mitchel

Brow hazards are a significant concern in coal mine ribs and form when weak coal sloughs out of a rib face and exposes an overhanging block of more competent rock or coal. Of 36 rib failure fatalities in the last two decades, 36% resulted from rib brow failures. This highlights the need to better understand the mechanisms driving brow formations and failures to mitigate this hazard and eliminate potential fatalities. The research team at Missouri S&T worked to enhance the current CPRR system and include the potential for these brow hazards. We employed physical modeling methods to build a scaled model from critical brow cases observed in the field. The dimensions and properties of the models were scaled down by 14.4 times from the field cases. The results of the physical modeling efforts were used to assist in calibrating distinct element numerical models vital to understanding brow formation and failure mechanisms. Subsequently, three physical models were created and tested to provide data on an otherwise impossible-to-capture event at the field scale. The results of these tests provided formed brow dimensions that agree well with those observed at the field scale. The brow dimensions were 1.25 inches deep into the rib, equivalent to 1.5 feet when scaled up. Similarly, the numerical modeling efforts provided good agreement by capturing a brow forming 1.55 inches deep into the rib. The physical model results further validate the applicability of physical modeling efforts for capturing otherwise difficult and dangerous phenomena in a controlled lab setting.

Feb 22, 2026

By V. K. Gupta

The experimental results of some wet batch and continuous grinding experiments carried out in a 40 x 40 cm grate discharge ball mill have been analyzed for the variation of the grinding rate parameters, Si, with various operating conditions using a linearized population balance model. The wet grinding tests were carried out under conditions which were very similar to those encountered in the actual practice in plant operation. Well distributed -4 and -20 mesh feeds of two complex pyritic ores were used. The volume-percent solids in the pulp ranged from 30-40, the particle load from 5-8 kg, and the solids feed rate from 70-1 10 kg/hr.

Jan 1, 1981

By R. C. Burtan

Long before the dawn of recorded history, man began to dig into the earth's crust in a never ending search for useful materials. It has been well established that prehistoric man discovered flint. "The Flintstones" were aptly named. The flintknappers of southern England and Wales still exist today in ever dwindling numbers as they seek out chunks of flint. It is a well known fact that more than half of the earth's crust is composed of silicon dioxide (SiO2), also known as silica. Silica and silica containing materials have a great many uses in modern society. However, this material is potentially extremely hazardous to our health. Centuries before the Christian Era, Hippocrates wrote of a lung disease common to those who mined in hard rock. It is obvious to us that he was describing silicosis. It is also apparent from ancient writings, that the Egyptians were aware of this malady. Dioscorides also wrote on this subject in the fifth century, B.C. It is undoubtedly the oldest and best studied of the occupational lung diseases. It was certainly described by Agricola in his "De Re Metallica" published in 1556, in which he described lung disease among hard rock miners. This publication, I'm sure, is of special interest and perhaps known to many of you in the mining community. The original document was written in Latin and was translated in 1912 by two gentlemen, Hoover and Hoover. One of these translators was Herbert L. Hoover, a former president of the United States, who made his living before his presidency as a mining engineer.

Jan 1, 1984

By George A. Savanick

Borehole (slurry) mining, in which a tool incorporating a water-jet cutter and a downhole slurry pump mines phosphate through a borehole, was field tested in northeastern Florida as part of a Bureau of Mines program to increase the domestic availability of critical minerals. Approximately 1700 tons (1.54x106 kg) of phosphate ore were mined at 40 tph (10.1 kg/s) from a depth of 250 ft (76 m). The borehole was filled with water during mining for roof support and to assist slurry pumping. Underwater cutting was enhanced with an air-shrouded water jet. Mined cavities were backfilled to prevent subsidence after abandonment. Roof subsidence during mining was avoided only when the cavity was filled with water. Environmental monitoring before, during, and after mining included hydrological studies and measurements of water quality. Significant water quality changes occurred only in the zone being mined and were confined to the immediate area of the borehole.

Jan 1, 1983

By M. Misra

It is estimated that the volume of low -level and intermediate level contaminants present in the soil at different DOE sites is of the order of several million cubic feet. The existing remediation scheme is containerization followed by burial in Land Disposal Facilities (LDF's) which is economically unattractive warranting the need to develop alternate remediation routes. One such route is the physical separation based volume reduction approach to removing a MINIMUM AMOUNT OF CLEAN SOIL with the radioactive particles, reducing the amount of material that requires disposal. The purpose of this study was to evaluate and test the feasibility of using physical beneficiation techniques for removal of contaminants from soil. The performance criterion was to recover at least 80% of the activity in 20% or less of the original contaminated soil volume. Four different radioactively contaminated (primarily uranium and plutonium) soils from DoE sites namely LANL, INEL, Fernald Plant 1 Storage Pad (ID-B) and Mound soils were tested using gravity, magnetic, gravo-magnetic, hydrocyclonic and flotation devices. The paper is divided into the two sections. The first section presents the overview of the Heavy Metals in Contaminated Soil Treatability Project conducted at the University of Nevada, Reno (UNR) describing the salient features of a state-of-the art Soil Washing Laboratory and the technology equipments used in the test program. The second section describes the soil characterization and typical volume reduction results obtained from the UNR tests. Among the physical separation processes, only flotation processes passed the performance criterion. For the LANL and INEL soils where the contamination was contained in coarse particle size, it was possible to recover more than 80% of the activity in less than 10-20% of the original volume of the soil thus rendering 80-90% of the soil "clean". For Fernald and Mound soils where contamination was of colloidal nature, flotation based processes showed encouraging results and are recommended for further studies.

Jan 1, 1995

By Kirk Carlton

This paper deals with a group of subjects so familiar to all of us that we might question the need for discussion. Even so, nearly every day's business turns up expensive examples of differences in understanding, misdirected assumptions and incomplete technical purchase documents. As our international activities increase, so do these problem areas. Their expense in both money and embarrassment gives rise to this attempt to focus a little extra attention on technical criteria and specifications. The two terms ?criteria? and "specifications" are, we believe, worth separating with respect to meaning. They should not be used interchangeably, although they often are. Criteria are by definition "standards for judging", whereas specifications are "enumerations of particulars". In relation to plant or project engineering, the criteria are the general rules and data which apply to the whole project and the specifications are the further listing of detailed requirements for specific contractual items or pieces of equipment. We'll look a little more closely at specifications after we give another minute or two to this "criteria" subject,

Jan 1, 1973

By S. D. F. Rocha, A. L. A. SANTOS, E. M. A. BECHELENI, R. M. Papini, P. R. M. Viana, F. P. C. Silvas

The kinetics of atmospheric sulfuric acid leaching from a Brazilian nickel laterite ore was assessed using distinct reducing agents and ore mineralogy. This transitional ore contains 1.63% Ni distributed as 1.27% in coarse size (− 500 + 150 μm), mainly as silicates (lizardite and chlorite—28.6%), and 2.06%in the fines fraction (− 75 μm), mainly as iron oxy-hydroxides (goethite and hematite—49%). The effects of temperature, acid concentration, reducing reagent type, and concentration were evaluated. The − 75 μm fraction limited the leaching efficiency and the use of reducing media with thiosulfate improved leaching and Ni-Fe selectivity. However, at constant Eh of 626–743 mV and a pH range between 0.2 and 1.1, no substantial rise in metals extraction, except for Co and Mn, has been observed. In order to determine the process control at 95 °C, two regions in the extraction curves were used in combination with the shrinking core model. Control by porous diffusion was observed and the kinetic constant was found to be in the order kFe<kNi<kMn<kCo<kMg for atmospheric leaching without Eh control. In reducing media for the first 15 min of leaching, the kinetic constant was found to be kFe<kNi<kMg≅kCo<kMn as derived from Ni disseminated into iron oxides structures.

Oct 7, 2020

By Irving Hoch

INTRODUCTION The demand for tunnelling can be related to urban population size and density; often, tunnelling occurs when a certain city size and density threshold is reached, and increases thereafter as a function of those population characteristics. Subways for rail mass transit are the most notable example, of course, but tunnels for water supply and perhaps for sewerage can also be related to size and density. As cities grow large they sometimes outgrow their local water supply and have to import water from distant places via tunnels; witness New York City, Los Angeles and San Francisco. And it has been suggested that Chicago use deep tunnels for storm water storage because tertiary treatment to meet water quality standards will require treating storm water runoff.(1) Other uses of underground space also increase with urban density, e.g., underground parking, concourses and shopping centers such as Rockefeller Center in New York City and the Place Ville-Marie in Montreal. These examples can be viewed as illustrative of the central point of urban land economics. As the number of people locating in a place increase, they bid up land values and make the more intensive use of land economic, with land defined to embrace the space both above and below the surface. Hence, we are led to think about the city, and of urban land use, in three dimensions. Now, if we accept the relation of underground space use to urban size and density, recent demographic trends seem anything but hopeful for future tunnelling demand: urban density is declining, population growth is slowing down generally, and there

Jan 1, 1974

By B. K. Slone

The depth at which it becomes more economical to use slope access as opposed to box-cut access for near-surface coal reserves, termed "transition depth," can be established for a given coal property by considering cost estimates for those parameters that determine respective access method. Fourteen parameters that influence access cost were identified and ranges determined. A Transition Depth Formula was developed to permit determination of the better method of accessing a reserve, given such information as highwall slope, road width, total bench width, pit dimensions, road grade, belt component costs, pumping costs, and cost of overburden removal and reclamation. In most cases, in Appalachia, studies indicate that the transition depth ranges between 20 and 30 m.

Jan 1, 1998

By R. Asamoah, P. Forson, W. Skinner, M. Zanin

Despite the seeming benefits decoupling pyrite and arsenopyrite minerals present in practice, little success has been achieved. The present study presents possible process routes for attaining selective flotation broadly capitalizing on differential oxidation between these minerals, and the use of a chelating collectors. The best performance was achieved with dithionocarbamate application following copper activation, yielding 81.4% arsenopyrite and 37% pyrite recovery. Preaeration followed by staged addition of xanthate produced 76% arsenopyrite and 31% pyrite recovery while reverse flotation of pyrite after H2O2 addition gave rise to rejection of 66% pyrite accompanied with 24% arsenopyrite.

Mar 2, 2022

By A. Arik

Reliable ore reserve estimates for deposits with highly skewed grade disributions are difficult tasks to perform. Although some recent geostatistical techniques are available to handle problems with these estimations, ordinary kriging or conventional interpolation methods are still widely used to estimate the ore reserves for such deposits. The estimation results can be very sensitive to the search parameters used during the interpolation of grades with these methods. This paper compares the ore reserve estimates from ordinary kriging using several cases in which certain search parameters are varied. The comparisons are extended to different mineralizations to show the changing effects of these parameters.

Jan 1, 1990

By B. Sameti

Blast engineers have been taking advantage of image-based rock fragmentation analysis methods for the past 3 decades to estimate rock size distributions. These methods utilize a wide range of image segmentation techniques, from manual to fully-automated, to delineate the edges of rocks in images. Rock delineation results are then converted to physical rock sizes (and percentage passing curves) by scaling the image pixels to correspond to physical measurements. The size scaling process is critical for acquiring physical measurements, but specific to the limitations of different applications. This article starts by presenting a shovel bucket-based fragmentation analysis system, where scaling is done using the known width of the shovel bucket within the image. Next, it describes methods that use pictures captured by digital cameras with scaling reference objects in the view. Finally, the article presents a method that uses three-dimensional imaging to capture images without the need for scaling reference objects. A portable device which utilizes a three-dimensional imaging method is proposed, and compared with the other methods. The proposed solution combines the generated three-dimensional points with the delineated rock boundaries in the image to reconstruct the surface, and generate accurate rock size estimates and percentage passing rock size distributions. System operation is described and its accuracy and performance are discussed for various scenarios. It is shown that since the device does not require a physical object for scaling reference, it is free from the limitations of other methods, and can be applied for automatic rock size measurement from various sources such as mining shovels, loaders, crushers, stockpiles, haul truck beds, and conveyor belts.

Feb 23, 2014