Search Documents

By Xuchen Fan, Chenyang Zhou, Yuemin Zhao, Liang Dong, Chenlong Duan

A gas–solid fluidized bed using magnetite particles is an effective methodology for coal beneficiation in the field of dry coal cleaning. Broadening the size range of magnetite used in the bed decreases medium preparation cost. In this study, a tapered fluidized bed was used to investigate a magnetite particle size range of −0.5 + 0.074 mm. The results showed that a tapered fluidized bed effectively strengthens mixing of magnetite with a wide size range (−0.5 + 0.074 mm). The results of beneficiation experiments indicated that with increasing tapered angle, separation efficiency increased and then decreased. The highest separation efficiency was obtained at a tapered angle of 10°. The optimal results showed that the ash content of the concentrate decreased from 31.82% to 12.33% with a probable error of 0.11, which indicated that a tapered fluidized bed was efficient to improve fine coal beneficiation performance.

By Amir Karami, Scott Munro

This paper focuses on remediation of a 3.6 km long water conveyance tunnel that suffered two large falls of ground (FoGs), one of which subsequently progressed to the ground surface, resulting in full collapse of the tunnel. The tunnel is part of a network of water conveyance tunnels and open channels that direct water into two turbines located in an underground powerhouse, originally constructed in the 1970s. At the time of construction, the tunnel was partially supported with shotcrete or rock bolts, with no further ground support added since construction. Two sonar surveys in 019 and 01 identied two adacent large FoGs in the tunnel, approimately 1.2 km from the tunnel outlet. Historical geological and geotechnical information indicated that the FoGs occurred within a 60 m wide fault zone. Remediation plans were developed, which included stabilization of the outlet channel, the portal, the tunnel leading up to the FoG areas (1.2 km length) and the FoG areas. Several remediation options were considered to restore the tunnel, including construction of a diversion tunnel to bypass the FoGs or remediation of the FoG areas with steel ribs and backlling the void above the FoGs to surface.

Jun 23, 2024

By M. Dayne Aldridge

A discussion of the definition of automation in mine ventilation applications is presented. The results of theoretical studies, experiments and practical experience from work in the United Kingdom, Belgium, Poland, the Soviet Union and the United States are summarized. Conclusions are drawn from these efforts and the prospects for the future development of automatic mine ventilation systems are explored.

Jan 1, 1978

By J. Drelich

An improved experimental procedure to measure contact angle has been consolidated with coal surface preparation involving polishing with abrasive paper, alumina powder, and a cloth, followed by ultrasonic and mechanical cleaning. Specifically, the captive-bubble measuring technique has been compared with the sessile-drop technique and the former has been recommended for the examination of the hydrophobic properties of coal surfaces. Results of the research program, which is currently under way, on the examination of the effect of the nature, amount, size and distribution of mineral inclusions in coal on its wettability are briefly reviewed.

Jan 1, 1999

Refractory copper ores (CROs) in central Africa contain copper minerals that are locked up in a micacious solid matrix or associated with carbonate, sulfide and phosphate minerals. Several researchers have reported that the recovery of copper from CRO material by an acid-leaching process is not economically feasible, due to the presence of excess gangue-acid-consuming minerals such as calcites, dolomite, asbolane and iron oxides. Since the proportion of acid-insoluble copper (CuS) is about 28% of total copper and total free sulfur is extremely small, sulfide flotation was considered unfavorable. Consequently, hundreds of millions of tons of CRO material have been stockpiled specifically at the Nchanga Mine of Zambia. In terms of copper distribution in CRO material, a significant portion of total copper exists as carbonates (39%) and oxides (17%), while 28% of the copper is acidinsoluble (CuS). The rest of the copper is in the form of carbonates (16%) and (hydr) oxides (17%). This means that only about 72% of total copper is recoverable through the non-oxidative acid-leaching process. In this study, batch leach tests were performed on CRO solids (d95 = 95%) to establish the gangue acid consumption values at different feed pH values and to evaluate the leaching characteristics of copper, manganese and iron within the CRO material. Subsequently, continuous leach tests were performed on CRO solids (106 um, 80% passing) using optimum leach conditions derived from batch tests. This paper aims to show that sustainable copper recovery can be achieved by selecting leaching conditions whereby gangue acid consumption (GAC) values become significantly small and the final concentration of manganese and iron in the leach solution are appreciably low.

Nov 1, 2011

Refractory copper ores (CROs) in central Africa contain copper minerals that are locked up in a micacious solid matrix or associated with carbonate, sulfide and phosphate minerals. Several researchers have reported that the recovery of copper from CRO material by an acid-leaching process is not economically feasible, due to the presence of excess gangue-acid-consuming minerals such as calcites, dolomite, asbolane and iron oxides. Since the proportion of acid-insoluble copper (CuS) is about 28% of total copper and total free sulfur is extremely small, sulfide flotation was considered unfavorable. Consequently, hundreds of millions of tons of CRO material have been stockpiled specifically at the Nchanga Mine of Zambia. In terms of copper distribution in CRO material, a significant portion of total copper exists as carbonates (39%) and oxides (17%), while 28% of the copper is acid-insoluble (CuS). The rest of the copper is in the form of carbonates (16%) and (hydr) oxides (17%). This means that only about 72% of total copper is recoverable through the non-oxidative acid-leaching process. In this study, batch leach tests were performed on CRO solids (d95 = 95%) to establish the gangue acid consumption values at different feed pH values and to evaluate the leaching characteristics of copper, manganese and iron within the CRO material. Subsequently, continuous leach tests were performed on CRO solids (106 um, 80% passing) using optimum leach conditions derived from batch tests. This paper aims to show that sustainable copper recovery can be achieved by selecting leaching conditions whereby gangue acid consumption (GAC) values become significantly small and the final concentration of manganese and iron in the leach solution are appreciably low.

Jan 1, 2011

By Jacob Mathis, Mark Bradford, Alston Noronha, R. M. True

In June 2022, Louisville MSD completed a 6.5-km (4.0-mi), 6.1-m (20-ft.) diameter CSO conveyance and storage tunnel system located along the Ohio River in downtown Louisville, Kentucky. For large diameter shaft and tunnel construction, drill-and-blast operations among other methodologies were used in close proximity to federal, commercial, and residential properties with no impact to stakeholder infrastructure. s one of the rst maor tunneling proects in Louisvilles metropolitan area, this paper explores Black & Veatchs rigorous geotechnical instrumentation monitoring program that provided uality assurance for local stakeholders and afrmed innovative tunneling solutions can be successfully executed in an urban setting.

Jun 23, 2024

By Shinzaburo Kato

In 1977 Kawasaki Steel Corporation (KSC) built No. 6 BF (Blast Furnace) with an inner volume of 4 500m3 as part of our program to produce 8.5 million tons of crude steel a year at Chiba Works. As the primary raw material to be used in No. 6 BF, we decided to use sintered ore, because we were confident in the obvious advantages of our technology developed by that time on sintering and BF operation using sintered ore. At Chiba Works, however, we had no space for the construction of a sinter plant, so we decided to build it abroad. Sintered ore is easily crushed and degradated. Producing sintered ore at a point far away from the blast furnace and transporting it across the ocean was the world's first attempt. To successfully realize it, we conducted a series of fundamental surveys and studies with special stress on the real aspects of degradation of sintered ore caused by long-distance transportation and handling and the ways and means to prevent the degradation. As a result, we decided to build a plant on the Mindanao of the Philippines.

Jan 1, 1982

By Thomas A. Gwynn

"A beautiful America will require the effort of government at every level, of business, and of private groups. Above all it will require the concern and action of individual citizens, alert to danger, determined to improve the quality of their surroundings, resisting blight, demanding and building beauty for themselves and their children." "Improvement of our environment" has become a cause much like "motherhood". The increased awareness of the public concerning this subject makes it most unpopular for anyone to be involved in anything that seemingly is detrimental to our environment. And this awarement goes far beyond our biggest pollution problem in America - the distribution of paper, abandoned automobiles, beer cans and other garbage by our enlightened society along every city, highway, trout stream, river and mountain in America. In fact, the greatest awarement comes because of the "sensational" reporting and writing in our various national communication media, wherein the same voting citizens who so generously distribute their refuse about the countryside are emotionally aroused and duped into transferring what is truly a national problem onto the shoulders of a few industries - notably and particularly the mineral extraction industry. Certainly mankind is more and more stumbling over his own garbage daily, a fact that is easier to sell a citizen of one of our large cities than a resident of the wide open spaces of the west. Yet even in the Rocky Mountain states, the "Land of Sky Blue Waters", the "Big Sky Country", and particularly in Salt Lake valley smog is not unknown. Pollution and littering have become problems that need to be faced squarely. In North Dakota alone it has been estimated that one section of farm land each year flows down the mighty Missouri and the greatest producer of sediment is now reported to be the highway department.

Jan 1, 1969

By James K. Hallenburg

Geophysical borehole logging is a valuable and inexpensive tool for coal deposit evaluation, development, and production. In addition to the usual determinations of depth and seam thickness, geophysical borehole logs can effectively and accurately determine the coal ash, moisture, and heat contents in situ. Location and evaluation of the partings can be done quickly and accurately. Overburden character determination, such as roof competence, dewatering parameters, ripability, trace element content of the coal and overburden, and sulfur content can be done with existing tools and techniques. The quality of such determinations depends upon the quality of planning and calibration.

Jan 1, 1984

By John K. Adams

Phosphorus may be incorporated into sedimentary rocks in at least four different ways: (1) by the accumulation of detrital mineral fragments, (2) by the accumulation of phosphatic organic debris, (3) by diagenesis and (4) perhaps by the primary precipitation of calcium phosphate. Based-on the petrographic examination of Cretaceous and Tertiary sediments from the northern and central parts of the Atlantic Coastal Plain, Diagenesis is the most important of these mechanisms. Both syndiagenesis and epidiagenesis are required to explain the origin of all the diagenetic phosphate mineral species which occur in the northern and central parts of the coastal plain. Syndiagenesis produced much of the coastal plain's apatite. It was operative below the sediment-water interface while the substrate was being compacted. Compaction forced pore waters, which were enriched in phosphate by the decomposition of organic matter, upward through calcareous sediments. The PO43- radicle replaced the CO23- and calcareous nodules, pellets and shell fragments were converted to apatite. Epidiagenetic reactions occurred in the subaerial environment where downward percolating meteoric waters carried phosphate in solution to cites where cation activity was sufficiently high to form new minerals. Vivianite may form where ferrous iron is available and wavellite and variscite may form in the presence of aluminum rich minerals. Textural evidence suggests that many of the reactions were repeated. The present day appearance of apatite, vivianite, wavellite and variscite in the coastal plain may represent several generations of diagenesis.

Jan 1, 1972

By Martin B. Hudson, John Yao, Matthew R. Crow, Yiming Sun, John T. Waggoner, Roozbeh Geraili Mikola

"The Wilshire Grand redevelopment project in downtown Los Angeles includes construction of a new 73-story tower. Construction required excavation up to 93 feet deep (28 m). The south side of the excavation, up to 57 feet deep (17 m), required placement of shoring within about 6 to 10 feet (1.8 to 3.0 m) horizontally away from a 400-foot-long (122 m) section of one of the existing Los Angeles Metro Red Line twin subway tunnels. These tunnels were constructed using a 22-foot-diameter (6.7 m) digger shield, and were initially supported with expanded, precast concrete segments, with final cast-in-place reinforced concrete lining. The temporary shoring system for the deep excavation consisted of soldier piles generally spaced at 8 feet (2.4 m) on center with multiple levels of tieback anchors extending above the subway tunnels. The lowest level of bracing consisted of rakers supporting walers attached to the soldier beams because installation of tieback anchors at that level would conflict with the tunnels. Numerical analyses were performed to predict tunnel movement caused by the excavation and its effects on the train operations. This paper describes the numerical modeling, tunnel and geotechnical instrumentation and monitoring program, and comparison of the computed and observed tunnel responses to the deep excavation and tower construction. With increasing urban redevelopment in major cities, the project is a valuable case history for excavation adjacent to existing tunnels. INTRODUCTION The Wilshire Grand redevelopment project includes the demolition of a 16-story hotel built in the early 1950s and the construction of a new 73-story tower in downtown Los Angeles (LA) that will be the tallest building in the western United States. The project site is situated on approximately 2.7 acres (1.1 Ha) of land bounded by Figueroa Street to the east, Wilshire Boulevard to the north, Francisco Street to the west, and 7th Street to the south (see Figure 1a). The new tower is being constructed by Turner Construction for Hanjin International Corporation. Construction of the basement and foundation of the new tower required excavation up to 93 feet (28 m) deep. Shoring was designed by Cefali & Associates and installed by Malcolm Drilling Company. Along 7th Street, an excavation up to 57 feet (17 m) deep required shoring to be installed within about 6 to 10 feet (1.8 to 3.0 m) horizontally from an existing 400-foot long (122 m) section of one of the LA Metro Red Line subway tunnels (see Figure 1b). The tunnels, extending from the 7th/Metro Station to the Westlake-MacArthur Station, were constructed in the late 1980s and early 1990s with an excavated diameter of approximately 22 feet (6.7 m). They were initially supported with expanded, precast concrete segments with a final cast-in-place reinforced concrete lining. The existing hotel was demolished in 2012 and 2013, with shoring installation and excavation for the new basement occurring as the demolition occurred. At the time of writing, January 2016, the structure of the building adjacent to the tunnels is largely complete."

Jan 1, 2016

By D. Brabec

One of the analytical problems in exploration geochemistry is the choice of a method of sample attack which would be rapid, simple and reliable in terms of precision and discrimination between different concentration levels of elements sought. The wet sample attacks currently used in analysis of silicate rocks vary from total decomposition to leaching by weak extractants. The total decomposition of such materials is usually achieved either by alkaline fusion or hydrofluoric acid attack. The first method requires the use of platinum vessels which is both expensive and slow for batch operation. The second type of attack is more widely applied in rock geochemistry1, but it is still relatively slow for exploration purposes and requires extra care (especially when hydrofluoric acid is used in mixture with perchloric acid). Considerable improvement in speed can be achieved by using the sample attacks which release only part of the metal present in a rock.2,4 One of such attacks is the leaching of pulverized rocks by hot aqua regia.3 Another technique widely used in geochemical prospecting involves fusion of the samples with potassium pyrosulfate (or bisulfate) followed by an acid leach of the malt .5 One of the advantages of these techniques is the use of glassware in decomposition stage which considerably increases the analytical productivity. It should be noted that partial chemical attacks tend to extract from a rock mainly the non-silicate metal which may give results more significant for exploration purposes than the analysis for total metal.

Jan 1, 1970

By Jr. Watts

The American Mining Congress and the U.S. Bureau of Mines have formed a collaborative research team to develop, implement, and evaluate a comprehensive control strategy to reduce diesel particulate matter concentrations without degrading other air quality parameters at an underground noncoal mine. Other participating organizations include Caterpillar, Inc., the Mine Safety and Health Administration, and the University of Minnesota. After extensive baseline information and air quality data are collected, available control strategies to reduce diesel particulate matter exposures will be implemented, individually or in combination, and evaluated. This paper discusses the objectives and protocol of the collaborative effort to evaluate diesel particulate control technology.

Jan 1, 1995

By J. F. Cornelsen

Wheel loaders are currently being used in many mining applications for a variety of reasons. While they sometimes provide the lowest loading cost, a primary advantage of the wheel loader versus other loading systems is the increased versatility and mobility inherent in a wheeled vehicle. The advent of large wheel loaders with much greater digging capability enhanced wheel loader usage in severe loading applications. To match these severe conditions, machines offered today were designed to work in these rocky conditions. Soon after the introduction of large wheel loaders into rocky conditions, however, it became apparent to many users that tire costs could at times account for up to 50% of total hourly operating costs on large wheel loaders. In some applications, tire costs alone pushed wheel loader economics beyond the economic feasibility for these jobs, prohibiting their use. In an effort to combat high tire costs, several attempts have been made to put fast moving steel around the tires to provide a strong interface between vehicle and ground. Some earlier attempts involved wrapping tracks around tires. Mechanical difficulties with these systems limited their customer acceptance. Subsequently, the development of protective tire chains came into favor. While tire chains offered added protection to the tires, the cost and maintenance of the chains remains a problem in 1972, the Dystred arrangement was announced for usage on a 6 cu yd wheel loader from Caterpillar Tractor Co. (See Figure 1). The Dystred offered the advantages of greatly increased tread life over conventional tires, as well as resistance to tread puncture in most situations. The arrangement basically employed a track system similar to that used on track type loaders. Pin and bushing wear often caused high hourly operating costs and excessive machine downtime. In addition, the connection of shoes through the use of links, pins, and bushings forced a limitation on too speed of the vehicle.

Jan 1, 1976

By Howard Brown

High purity, high brightness limestone deposits in the San Bernardino Mountains and Mojave Desert region occur in upper Paleozoic carbonate rocks which are part of an upper Precambrian and Paleozoic sequence that unconformably overlies crystalline basement. The Paleozoic strata are divided into formations and members, and correlated with strata of the inner Cordilleran miogeocline. The region has been affected by multiple Mesozoic intrusive, contact, and regional metamorphic events. Structure is complex, and includes polyphase Mesozoic folding and thrusting, and complex Cenozoic structures. The area continues to be seismically active. High brightness (white), high purity crystalline limestone deposits are uncommon because their formation is dependent on several geologic processes which include; 1) depositional environment, 2) contact and or regional metamorphism, 3) folding and faulting, 4) uplift and erosion, and 5) preservation through geologic time. The complex geologic history of the San Bernardino Mountains and Mojave Desert region has allowed the formation of several large high brightness, high purity limestone deposits which are currently being mined or will be mined in the future. Specialty Minerals, Inc. (formerly Ptizer), Pluess-Staufer (California), Inc. and Partins Limestone, Inc. produce high brightness, high purity limestone from several quarries in the San Bernardino Mountains. These active mines combined with undeveloped deposits controlled by Pluess-Staufer in the San Bernardino Mountains, New York Mountains, and Bristol Mountains in the Mojave area, contain proven and or indicated reserves sufficient to sustain production through the 21st century Detailed geologic mapping, intimate knowledge of stratigraphy, recognition of complex structures, sampling, drilling and assay data, are proven tools in the discovery and delineation of high brightness, high purity limestone deposits in the San Bernardino Mountains and Mojave Desert region of southern California.

Jan 1, 1995

By T. O. Llewellyn

The Bureau of Mines, U.S. Department of the Interior, conducted studies to recover phosphate from four dolomitic southern Florida deposits not currently mined. The samples contained 5.8 to 10.2 percent P205 and 1.7 to 1.8 percent MgO. Chemical analyses of sized fractions indicated that no pebble concentrate (plus 1.2 mm) could be produced from these samples. A scheme was developed that consisted of desliming, grinding, scrubbing, and redesliming the ore to produce a flotation feed. Conventional one-step fatty acid-fuel oil batch flotation tests on the samples resulted in concentrates containing 29.0 to 31.3 percent P205 at flotation recoveries ranging from 72.4 to 96.1 percent of the flotation feed. The MgO content of the concentrates ranged from 0.47 to 1.36 percent. Continuous flotation of the Manatee No. 2 sample indicated that commercial-grade phosphate concentrates analyzing 31.3 percent P205 and 0.55 percent MgO could be produced with a flotation recovery of 89.9 percent. The MgO content of concentrates obtained from the Manatee No. I and Hardee samples was 1.20 to 1.36 percent, respectively. Leaching with aqueous SO2 reduced the MgO content of these phosphate concentrates to 0.5 and 0.8 percent, but with a concomitant loss in phosphate recovery.

Jan 1, 1983

By Tyler Lahti, Peter Borgacci, Mary Jane Ferraro, Prakash Nadesparan

Toronto Tunnel Partners (TTP), under contract to Metrolinx/IO, is constructing new twin rail tunnels under the Highway 401 & 409 interchange to accommodate additional tracks to support the GO Expansion program for future two-way, all-day service. The new tunnels are being constructed using the Sequential Excavation Method (SEM) and utilize a tunnel pre-support system consisting of a series of 800 mm diameter steel pipes to form a pipe canopy. The pre-support pipes were installed with an Auger Boring Machine (ABM) in four separate headings; one heading from each of the tunnel end portals, and two from a shaft in the middle of the highway. To facilitate the auger boring operation, a custom steel reaction frame was required to counteract the thrust from the ABM at the portals, and a temporary shaft structure was installed in a narrow median space of the highway. The installation of the pipe canopy had to overcome challenges including removal of obstructions, alignment issues, and controlling settlements to the highway surface. This paper discusses the purpose of the pipe canopy, design and installation of the temporary shaft and structures to support the auger boring operation, the experience of the contractor during the installation of the pipes, and brief overview of the experience tunneling below the pipes.

Jun 13, 2021

By Harry Perry

U. S. consumption of sulfur and sulfur products is expected to increase at a rate of 8 percent per year between now and 1980, largely as a result of their use in fertilizer markets. World consumption is also increasing rapidly, but at a-lower rate, about 6-percent per year. In 1965, sulfur recovered in the United States from purification of natural gas; nearly doubled from the 1956-1960 average; production from pyrites declined; and production of elemental sulfur increased 15 percent. Concern about air pollution resulting from sulfur oxides produced from the combustion of fossil fuel has lead to intensive research on methods of removal before combustion, during combustion (in-process methods), and from the resulting flue gases. If all the sulfur in fossill fuels were recovered, more sulfur products would be produced than were consumed in the United States in 1965. Removal of sulfur from coal before combustion could result in a product sufficiently-high in sulfur to be a suitable raw material for sulfuric acid manufacture. In-process methods produce solid sulfates, some of which may have commercial value. Flue gas removal' methods for sulfur oxidest generally result in the production of a byproduct either of sulfuric acid or sulfur. The projected sale of these materials significantly lowers the anticipated cost of sulfur dioxides pollution abatement. Alternate methods for sulfur dioxide reduction are discussed. The various proposed processes are described and costs are given for the various methods for which estimates have been made.

Jan 1, 1967

By H. D. Lelono, M. Walden, G. Johnson

3D modelling can be used throughout the mine lifecycle and has proven to be a powerful tool for consultants and mining companies. One of the most significant benefits of 3D models is their ability to enhance collaboration, communication, and understanding between the mine owner, design engineers, and other relevant stakeholders that have a shared interest in responsible mining and site management. Tailings and mine waste management is an interdisciplinary effort that requires effective coordination and communication between a wide range of consultants, operators, and stakeholders alike. The increased emphasis on Environmental, Social, and Corporate Governance (ESG) highlights the importance for mine operators to engage and communicate with all parties involved in the planning, permitting, operation, and closure of mine sites. 3D models are valuable tools that can be used for development of geotechnical conceptual models, allowing for improved design and monitoring of Tailings Storage Facilities (TSFs). A clear conceptual understanding of a TSFs subsurface geology and foundation characterization is essential for proper tailings management, design, and planning. Visualization with 3D modelling can simplify the interpretation of the, oftentimes intricate, mine sight subsurface settings and allows for quick and effective geotechnical conceptualization. 3D models can be used to identify data gaps, optimize field investigations, and streamline the development of numerical stability or groundwater models. They can help communicate the complex nature of subsurface and TSF interactions in a clear, concise, and accurate manner to both technical and nontechnical stakeholders. This paper discusses some of the benefits of 3D modelling in relation to geotechnical analysis for tailings management and provides methodologies for how to improve upon some methodologies that are considered industry standards.

Feb 1, 2023