Search Documents

By G. Deschênes

In an earlier study (Deschênes et al., 2009), gold and silver were shown to be efficiently extracted from samples taken from the Kupol Mine in Russia using lead nitrate in a cyanide leach system. In the current study, a com-parison of the technical and economic merits of a new technology called CANMET enhanced leaching process (CELP) was made with the cyanidation/acidification-volatilization-recycling (AVR) process using eight metal-lurgical variability samples, as well as a large composite sample, which was to represent the initial two years of Kupol mill feed. The composite sample leach feed assayed 33.4 g/t Au and 289 g/t Ag. The metallurgical results from the large composite sample demonstrated that CELP produced very similar gold and slightly higher silver leach extractions compared to the conventional cyanidation/AVR leach conditions at 1/2 the cyanide concentra-tion (1,000 ppm NaCN in CELP vs. 2,000 ppm for cyanidation/AVR leach conditions). It was estimated that the total cost per ton was approximately the same for the two technologies (total cost of CELP with the use of Merrill-Crowe at $46.48/t, with cyanidation/AVR at $46.13/t). However, the implementation of CELP would eliminate a capital expenditure of approximately $5 million for an AVR system based on a 2005 feasibility level cost estimate. Eight variability samples used to confirm the composite sample results showed that, on average, the gold leach extractions with CELP and the conventional leach conditions were very similar, but the average silver leach extraction was 2.1% higher for CELP. Furthermore, CELP silver leach extraction was 4.6% higher on average compared to conventional cyanidation for the four mid-grade variability samples evaluated. The decision was made to remove AVR cyanide recovery from the flowsheet and implement CELP at Kupol. The ability to use the conventional leach equipment with CELP and simplify the flowsheet was also a factor, given the remote location of the Kupol Mine.

Jan 1, 2010

By S. G. Dixit

Alunite (KAl3(SO4)2(OH)6] is one of the important nonbauxitic resources for aluminum in U.S.A. The major gangue material associated with a unite ore body is quartz. Experimental results indicate that oleic acid flotation of alunite is quite effective in upgrading the ore. The flotation chemistry of the alunite/oleate system has been investigated using various techniques such as: hallimond tube flotation response, measurement of adsorption density using I4C labeled oleated, electrokinetic measurements, infrared spectral studies, contact angle measurements and thermochemical measurements using an isothermal microcalorimeter. Alunite has been found to float readily with oleate in the pH range 4-10.5 and its flotation response is enhanced at higher temperatures. The PZC of alunite has been determined to be at pH 7.2 ± 0.15 which agrees with what would be predicted from solution chemistry and from the flotation response with physically adsorbed collectors. Infrared spectra show a specific peak in the range 1585-1600 cm-1 which has been attributed to the formation of an aluminum oleate surface species. Both adsorption density measurements and infrared spectra indicate that during adsorption multilayers are formed. The heat of adsorption of oleate on alunite has been found to be endothermic and of the order of 4-6 KJ/ mole.

Jan 1, 1980

By C. J. B. Dreyer

In terms of resources of amphibole asbestos only South Africa can be considered. There are only two asbestos producing fields, one in the Northern Cape Province producing only crocidolite and one in the Eastern Transvaal producing only amosite. The banded ironstone sequence in which amphibole asbestos occurs is discussed, and the genesis of the fibre is briefly reviewed. The properties and characteristics of amphibole asbestos are discussed and compared to those of chrysotile. Approximately 300,000 tonnes of amosite and crocidolite are produced annually. Crocidolite has a potential for a fivefold increase of production, which could be sustained beyond the year 2000. An estimate of the resources of the various producing fields in South Africa is made. Mining methods are reviewed and evaluation techniques discussed.

Jan 1, 1978

By D. S. Dinsmoor

Boron, estimated to comprise about 0.001 percent of the earth's crust (Fleischer 10), as an element is never found free in nature, although its compounds are found in many localities. the borates are the most important. Sassolite (B(OH)3) and boracite (Mg6C12B1406), non-borates, are-of-minor importance. The crystal structures of most natural borates are still unknown. A classification based solely on the ratio of boron to the total number of cations has been devised (Palache 28). This classification divides the borates into four, sub-groups; anhydrous borates, hydrated borates, borates containing hydroxyl or halogen and compound borates. Only four or five minerals of the hydrated borates group have ever been used commercially. In more recent years, the sodium borates have comprised all but a 'small fraction of all borates used. Borax, the hydrated borate compound, is the most important of all boron compounds. It has been used so long and so often that the layman often confuses borax and boron and, applies the terms synonymously.

Jan 1, 1958

By Mark A. White

Arch Mineral has developed several computer programs that aid the surface mine planning function. These programs are utilized to perform long term projections for various area or semi-area stripping operations. The program generated reports include yardage, tonnage, quality and ratio information for the user-specified time periods. The projections are used to anticipate the annual budget, to compare alternative mine plans and to analyze acquisition candidates. The programs are user friendly, fast and accurate. Geological Grid File Two data files must be set-up and used in conjunction with the mine planning programs. These are a geological data file and a general input file.

Jan 1, 1984

By G. Pan

Although geostatistical techniques have been widely accepted as the standard methods for reserve calculations in the mining industry, the production data of many mines frequently differ from geostatistical estimations based on exploration and development drilling. The discrepancies in recovered metal amounts, commonly in the range between 10% and 30%, are related to different factors. Major causes vary from mine to mine. A common cause, however, is the ignorance of important geological constraints in reserve modeling. Three major factors appear to be related to such an unfortunate fact: 1) modelers are over-confident on geostatistical techniques, 2) it is difficult to establish geological models, and 3) mine schedules are too tight to allow detailed geological modeling work. Defining mineralization envelopes has been a major effort in geological modeling. Past experiences have showed that geological modeling is much mo~ demanding than the choice of sophisticated kriging estimators. Since building envelopes for complex ore bodies can be extremely tedious and time-consuming, computerized approaches are badly needed for mine modelers. A comprehensive procedure reported here is referred to as probability-assigned constrained kriging (PACK), which includes a built-in method for defining 3-d mineralization envelopes. The modeling technique is fast and accurate for complex precious metal deposits. The technique is demonstrated on a gold deposit. The estimation results are compared with blast-hole based production panels, showing that the estimated tonnage is 2.2% larger than the actual production and the average grade is 2.6% lower.

Jan 1, 1994

By Alistair James, James Alcorn, Chaitan S. Sandhu, Andy Small

The Risk-Informed Decision Making (RIDM) working group is a group of industry professionals formed under the joint initiative undertaken by United States Society of Dams (USSD), Tailings Dam Safety Committee and Canadian Dam Associations (CDA) Mining Dam Safety Committee (MDC). The working group was organized to develop a guideline on implementation of a RIDM process relating to the design of mining water dams and Tailings Storage Facilities (TSF). Since its formation in 2022, the group has completed a literature review of more than one hundred (100) cross industry publications on applications of RIDM in mining water dams and TSFs, has held two industry workshops in Niagara Falls, Ontario in 2024 and Saskatoon, Saskatchewan in 2025 to capture industry input relating to the understanding and application of RIDM. The working group has subsequently formulated a process that constitutes good industry practice as it relates to application of RIDM in mining dams and TSFs. The authors, through their engagement and leadership in the working group and facilitating the two industry workshops in 2024 and 2025, are of the opinion that the successful application process of RIDM across Canada and United States (U.S.) is still not clear to many industry practitioners. There is confusion over terminology, good versus poor RIDM, and in some cases reluctance to use the RIDM terminology. This paper addresses critical knowledge gaps identified in the RIDM implementation for mining water dams and TSFs through three years of stakeholder engagement. It provides clarity of the process via a joint position statement and implementation roadmap, resolves terminology confusion, and documents contradicting industry opinions to promote adoption of good RIDM practices in Canada, U.S. and beyond.

Feb 22, 2026

By R. D. H. Bedd

GEOLOGICAL NOTES The area under discussion is situated approximately 150 m north of Loraine No. 3 shaft at ± 1500 m below surface. The block being mined extends from about halfway between 50 and 52 levels to just below 48 level (see Fig. 1). The EB reefs form the lower portion of the EB zone of the Elsburg series and in the 81 line area the various conglomerate bands show the best development. Up to 18 separate reef bands are developed and the distance from the bottom conglomerate band to the top is ± 26 m. The thickness of the quartzite which forms the middling between the various reef bands varies from 0.1 to 2 m. The strike is roughly north-¬south. The reef bands are payable individually. However, owing to the steepness of the reefs and their close prox¬imity, conventional mining would prove very difficult. The nonpayable reef bands all carry varying amounts of gold and the whole area is a massive payable reef body approximately 26 m wide and 60 m high at 300 to 400 m on strike. The major structure of the area consists of a north¬-south trending syncline. The western flank of the syncline has a steep easterly dip, in places approaching the vertical. This flank cuts out against the overlying rocks of the EA zone. The latter forms a noncon¬formity with the underlying EB zone. The eastern flank of the syncline dips to the west at an average dip of 0.17 rad (10°). The 0.1 rad (6°) north-plunging syncline was sub¬jected to severe faulting. The most important are the Nos. 4 and 10 faults, both of which have a roughly north-south strike. The No. 4 fault dips to the west at an angle of 1.04 rad (60°) with a downthrow of approximately 150 m to the west. The dip of the No. 10 fault is 0.69 to 0.81 rad (40° to 50°) west, with the western block having moved 150 m updip relative to the eastern block. The EB reefs are being mined by the sublevel stoping method down from the sub-outcrop position to the cutoff against the No. 4 fault. On the downthrow side of the No. 10 fault, that is just above the 54 level, two reef bands are payable and will be mined conven¬tionally. ROCK MECHANICS From the section in Fig. 1, it can be seen that the area under consideration is surrounded by stoped-out areas. This will naturally change the stress distribution extensively. The only way to calculate the stress field for such a geometry is to use the finite element method. It was established that this method worked for the present geometry and so the method was applied to predict the stress behavior of the final geometry. From the results, it appeared that the effect of the old stopes was to destress the area. There are, however, some areas-such as the 50 and 48 north footwall haulages-which will require continuous attention. In these two footwall haulages, deterioration can take place due to tensile stress which

Jan 1, 1982

By Yosry A. Attia

One of the most significant advances in Mineral Processing in recent years, is the development of the selective flocculation technology. The technology is primarily aimed at recovering the mineral values from ultrafine ore suspensions. This is achieved by selectively aggregating the mineral particles in question to such size as to enable their effective separation from the suspension. Selective flocculation utilizes the differences in the physical-chemical properties of the various mineral components in the mixed suspension. It is based on the preferential ad- sorption of an organic flocculant on the particular solids to be flocculated, leaving the remainder of the particles in suspension. In order to understand the mechanics of this process, selective flocculation may be divided into four major sub processes; these being: ore slurry dispersion, in which all the particles are stably and uniformly distributed in the suspension with the individual particles being essentially separate; flocculant selective adsorption and floc formation; floc conditioning, which aims at obtaining flocs with desire properties for their subsequent separation and with minimum entrapment of dispersed particles; and floc separation from the suspension. These sub processes will be reviewed later in this article.

Jan 1, 1982

By S. Lu

The particle-bubble attachment and the rupture of formed aggregates in flotation cell were investigated in terms of turbulent regime. It was found that the particle-bubble collision rate is closely correlated to the energy barrier between particles and bubbles, and no adhesion takes place for the hydrophilic particle-bubble system due to the introduced ?capture efficiency? f(a) being zero. The values of an especially defined Weber number, i.e. the ratios of turbulent stress to aggregate strength in the inertial subrange of turbulence were estimated, the results showed that the detachment of a particle from a bubble involved in an aggregate is mainly caused by the turbulent stress only in the impeller zone, no bubble splitting occurs both in the impeller zone and in the bulk zone.

Jan 1, 1993

This treatise presents the application of the vertical furnace in a carbon regeneration system. Comparison is made to a rotary kiln. The construction, operation and control of the vertical furnace and system components are discussed. Advantages include high efficiency, fuel economy, minimal mechanical apparatus and maintenance, atmospheric and temperature control, ease of operation and reliability.

Jan 1, 1985

By Christopher J. Bise

It is somewhat reassuring to note that the United States has an abundance of coal reserves which can be used to bridge the widening gap between the nation's energy production and consumption. The U. S. Bureau of Mines has recently established a demonstrated coal reserve base of 434 billion tons. (31)(Figure 1) As can be observed, the major percentage of the reserves is in the West. Although surface coal mining in the West has been gaining increased attention in recent years, western reserves that must be deep mined are significantly greater. Though deep mining activity in the west is very limited and accounts for less than 2% of the annual production, the primary reason, quite probably, is the greater thickness of the seams as compared to those found in the East. Forty-five billion tons of the western demonstrated coal reserve base for underground mining are in seams greater than 10 ft. in thickness. (37) Thick coal seams do not lend themselves readily to extraction with the underground mining methods practiced in the United States today. Experiences from the practices in other countries can serve only as guidelines. Consequently, a concerted effort is necessary to overcome the technical difficulties.

Jan 1, 1975

By Yi Luo

Subsurface strata movements and deformations caused by longwall mining operations in underground coal mines could affect many important coal mining activities, such as gob well degasification, ground water protection and multiple seam mining. The stratifications in the overburden have significant influence on the subsurface and surface movements and deformations in the ground subsidence process. An enhanced subsurface subsidence prediction model considering overburden stratifications has been introduced in this paper. In this method, the entire overburden strata are equally divided into a finite number of layers and the percent of the hard rocks in each layer is an additional input. The proven influence function method is applied to predict the subsidence on each of the predefined layers progressively upward using the predicted subsidence on the previous layer as the subsidence cause for the current layer. A computer program is developed to facilitate the calculations. A case demonstration is used to show the applicability of the proposed subsurface subsidence prediction model.

Jan 1, 2012

By Nikhil Dhawan, Shrey Agrawal, Ashwini Kumar

The current study investigates sericite clay as an alternative source of potash and alumina. The alumina and potash content in the sericite is approximately 35 and 10%, respectively, compared with 50–55% in bauxite ore. Muscovite and illite phases are stable, and direct leaching is found to be ineffective. Here, planetary ball milling was performed, which provided dissociation of stable phases to relatively reactive phases. The milling led to a five-fold increase in the surface area, resulting in enhanced leaching kinetics even at low acid concentration. The statistical design obtained optimal conditions of 8 h of milling followed by leaching in 1.73 M HCl at 75 °C, yielding 82% alumina extraction in precipitate with 85% purity in γ-alumina form and 63% potassium dissolution in sylvinite phase. The yield of the precipitate was ~65–68%, and the acid leach residue contained primarily silica.

By Hamed Khodadadi, Hamid Ghadiri

In this study, a fuzzy logic self-tuning PID controller based on an improved disturbance observer is designed for control of the ball mill grinding circuit. The ball mill grinding circuit has vast applications in the mining, metallurgy, chemistry, pharmacy, and research laboratories; however, this system has some challenges. The grinding circuit is a multivariable system in which the high interaction between loops, the variation of the system parameters with time, and time delay are some of the problems that pose a challenge. Since the controller parameters are determined offline in classic PID control, these gains are unchangeable and cannot overcome the mentioned challenges in this system. Hence, a fuzzy logic self-tuning PID controller, which is a combination of fuzzy logic and a conventional PID controller, is proposed to control the grinding system, especially in the presence of model mismatch and disturbances. In addition, in order to solve the system challenges, a multivariable control approach based on an improved disturbance observer is proposed to suppress the effects of the disturbances. The most important feature of the algorithm proposed in this paper as the combination of fuzzy logic self-tuning PID and improved disturbance observer is its ability to eliminate system interaction, attenuate internal and external disturbances, and compensate the effect of system uncertainty on the performance of the ball mill grinding circuit. Simulation results in the cases of the set-point change in particle size and circulating load in the presence of model mismatch and external disturbances confirmed the controller performance compared to other controllers.

By P. James

"INTRODUCTION Control of target stream acidity is widely used in MIW (mining influenced water). Tailoring pH (a measure of acidity) finds application for controlling key chemistry in both process and waste streams. Traditional lime addition for neutralization and precipitation is most often used but has high reagent costs and results in large amounts of mixed metal sludge requiring costly disposal. A new adaptation of BPS’s patented DEMET™ technology (Dynamic Electrolytic Metal Effluent Treatment) platform offers a potentially improved and “reagentless” alternative to traditional chemical addition for pH adjustment. Electricity rather than chemical addition utilized in BPS’s proprietary approach controllably tailors target stream pH. The method offers a simple, low-cost processing technique yielding cleaner treatment chemistry. BPS’s “green” approach may yield lower operating (OPEX) and life cycle costs and significant reductions (up to 50%) in sludge generation compared to conventional lime treatment. It can also allow new opportunities to generate revenue via selective recovery of valuable processing byproducts. Specific savings and revenues depend on the target site chemistries, details, and processing goals. A more detailed discussion of the process and its operational principles may be found in Reference One.[1] Here application of the BPS treatment to POx (Pressure Oxidation) leaching as an alternative to traditional chemical addition is examined. An example operation process flow for gold mining is considered.[2] Promising processing points for potentially replacing conventional processes with DEMET are noted. The possibilities for lowering OPEX costs, lessening sludge creation, and capturing various valuable byproducts and residuals are examined. Financial life cycle benefit estimates of the principal gains provided by DEMET application to the example operation are noted. Extension and generalization of the analyses to a wider range of scenarios is explored."

Jan 1, 2016

By R. G. Sinclair, E. Sangine, S. M. Fortier, J. Brainard, K. Stone

"The U.S. Geological Survey and Natural Resources Canada conducted a study on the net import reliance of each North American country, and the impact of North American trade on the net import reliance of 12 nonfuel mineral commodities that are associated with advanced technology products: cadmium, cobalt, gallium, germanium, graphite, indium, lithium, nickel, rare earth elements, selenium, silver and tellurium. The combined results for North America, using 2014 data, showed greatly reduced net import reliance for nearly all of the commodities evaluated, which is largely the result of pooling the resources of production and recovery in Canada and Mexico of materials that are consumed in the United States. This study highlights the mitigation of potential supply risk for critical materials that results from trade within the North American trade bloc. IntroductionMultiple metrics and definitions exist for what constitutes a critical material, but there is broad acknowledgment that a mineral commodity may be considered critical if, among other factors, its production is geographically concentrated, if it has few or no substitutes, or if the country of origin is politically unstable. Numerous governmental and independent researchers have proposed methods of investigating criticality, with differing priorities such as economic resilience or strategic military supplies (European Commission, 2014; Graedel et al., 2015; U.S. National Science and Technology Council Subcommittee on Critical and Strategic Mineral Supply Chains, 2016). While criticality really depends on who is asking the question, and despite the differing priorities, there are several commodities that are commonly found to be of concern. In particular, some critical or potentially critical materials are used increasingly in advanced technologies, or they have complicated supply chains because they are coproduced or are produced in controlled markets.Commodities for which imports are required to satisfy domestic demand are those for which the importing country is net import reliant. Net import reliance (NIR) in this study is calculated as the amount of imported material, including changes in stockpiles, minus exports and is expressed as a percentage of domestic consumption:"

Jan 7, 2018

By J. Kemeny, J. Lyons-Baral

"Point cloud technology is now an indispensable tool in geological and geotechnical data collection, interpretation and analysis. Open-pit and underground mines of all sizes are regularly collecting point cloud data as laser scanning (LiDAR) and photogrammetry surveying devices have become affordable and the workflows fast and efficient. Past challenges of large data processing and manipulation are gone with recent technological advancements in computer hardware and software. These innovations reduce file sizes, ease rendering requirements and allow for the implementation of real-time 3D viewers and surface meshing tools. With its ability to remotely and safely, rapidly and accurately extract large quantities of georeferenced and 3D-oriented data, point cloud technology provides numerous applications to the geomechanical field. The list of uses is continuously growing. This article specifically focuses on digital outcrop modeling and digital terrain engineering. Point clouds. The high-resolution and increasing availability of point cloud technology is rapidly improving open-pit and underground mines’ investigation, interpretation and characterization of site geology and rock mass properties (Kemeny et al., 2015; Lyons-Baral, 2012). LiDAR and photogrammetry are common remote sensing methods employed to measure the coordinates of surfaces in three dimensions (3D), providing the X, Y and Z locations and typically the reflective intensity and/or the visible three-band color of each point (Fig. 1).LiDAR uses either a time-of-flight or phase-shift measurement of a laser beam reflected off targeted surfaces and received back into the device.Photogrammetry generates point clouds by merging multiple overlapping photographs and uses stereographic plotting to define the locations of object points in 3D space. These methods can be deployed from airplanes, unpiloted aerial systems (UAS or drones), tripods, land vehicles and even in a mobile backpack shown in Fig. 2. RADAR, Total Station-Prism and other remote sensing systems also offer very precise “point clouds,” but this article does not address these due to their higher cost and lower versatility and mobility."

May 1, 2016

By M. Noppé

"Dilution in underground coal operations can be underestimated by up to five times during Feasibility Studies, with disastrous economic consequences. Every 1% of stone waste introduced can reduce an in situ specific energy of 11,000 BTU/lb (25 MJ/kg) by some 110 BTU/lb (0.25 MJ/kg) and increases the abrasiveness of the run-of-mine coal. Where a wash plant is not in place, penalties imposed for not meeting contractual specifications alone can amount to some AU$1 million per year.This paper presents a method for monitoring, reporting and ultimately controlling dilution in an underground coal mining operation. The dilution trends before and after introducing the recommended controls in a continuous miner/longwall mine are presented over an eight year period. The additional information from such a dilution monitoring program can also be used to control mining horizons and plan longwall extraction heights across the face proactively, on a short-term scale with resulting improvements in productivity. INTRODUCTION Grade control, as practiced on any mine, is concerned with predicting routine quality and tonnage values for short- to medium-term mining operations, and the reconciliation of these predictions against “actual” results. For a longwall mine supplying steam coal, such routine parameters may include the proximate analyses, specific energy (SE), abrasiveness and sulphur, as well as float and sink analyses if the coal is beneficiated. In addition, grade control is concerned with identifying the mineable horizon (or horizons) in a selective-mining operation, together with monitoring how well these horizons have been extracted or adhered to. Close-spaced surface drilling can be costly for any mining venture, particularly for longwall mines operating in the deeper seams. For this reason, much of the data for short-term grade control requirements are acquired during actual bord-and-pillar development. The underground data are derived from so-called “channel” samples. These samples are cut or chipped from the coal seam, perpendicular to the mining horizon, with dimensions suitable for obtaining sufficient “representative” sample for analyses. For a 2m thick mining horizon, a channel sample 300 mm wide and 50 mm deep over the thickness of the horizon would provide some 4.5 kg of sample, sufficient for most of the necessary tests. To allow the information to be computer recorded, additional information such as seam thickness, sample co-ordinates, and the elevation of the seam (or horizon) roof or floor, may be required."

Jan 1, 2015

By James E. Lawver

During 1981 the Florida phosphate industry produced more than 43 million metric tons of phosphate rock - about one-third of the entire world production and also generated nearly an equal amount of waste clay and waste clay-sized product that requires dewatering and disposal. The material balance of solids and water for a typical Florida phosphate mining operation is shown in Figure 1. Historically, the industry has impounded clay waste (about 60% below ground and 40% above ground) in earthen dams, often as large as 800 acres and occasionally greater than 60 ft. high. The dams have served the triple purpose of: 1. Dewatering initial 3% solid waste clay for process water re-use. 2. A reservoir system to minimize water discharge from the mining area and to capture and store rainwater thus minimizing deep well pumping requirements. 3. The ultimate densification and storage of waste clay.

Jan 1, 1983