Search Documents

By Jianping Zuo, Chunlei Zhang, Yong Zhang, Shouyang Gao

To study the fracture evolution of overlying strata for ascending mining in a short-distance coal seam group, a two-dimensional physical simulation model was designed based on a specific geological condition. The fracture development zone was divided into the compaction zone and active zone by monitoring and analyzing the macro fracture evolution of the surrounding rock mass during the excavation of multiple coal seams. The secondary fracture development process of the overlying strata was demonstrated with a physical model. The quantity, length, and inclination of the fracture were calculated with MATLAB software, and the results were verified by geological radar. The total number of fractures between two coal seams increased with a “parabola” shape during the excavation of the lower coal seam, the crack angle was mainly vertical and horizontal, and the number of horizontal cracks first increased and subsequently decreased; the excavation of the upper coal seam caused the secondary fracture development process of the overlying strata, and the relief range and its extent increased. The mining-induced cracks from the lower and upper coal seams connected with each other, especially the permanent vertical fracture in the cutting room side and face side. Finally, the three-dimensional gas fissure was formed.

Nov 24, 2020

By G. Deschênes

Silver minerals are known to have slow leaching rates and low overall extraction and require a high concentration of cyanide and a long retention time to maximize leach extraction. Their response to cyanidation is considered mild to moderately refractory, largely due to complex mineralogical compositions. New research on improving the dissolution of silver minerals in cyanide was performed using high-purity minerals, as well as a high-grade ore sample from the Kupol property, owned 75% by Kinross Gold. The high-purity silver minerals studied in the leach investigations included acanthite, stephanite and pyrargyrite, which were also the predominant silver minerals in the Kupol ore sample. Dissolution of silver from acanthite produced only 37% extraction in 48 hours of leaching with 500 ppm NaCN. Analysis of the leached acanthite surface showed appreciable formation of polysulfide species, which can interfere with silver leaching. Adding lead nitrate into a pretreatment stage increased the acanthite silver extraction to 86.2%. No polysulfide species were formed with the addition of lead nitrate from the surface analysis. Cyanidation of stephanite and pyrargyrite produced very low dissolutions of silver, only 12.6% and 10.4%, respectively, in the absence of lead nitrate. Silver extraction from stephanite improved to 98% by adding lead nitrate directly to the leaching stage, whereas pyrargyrite required a pretreatment with lead nitrate to extract 83.2% Ag. With the addition of lead nitrate, the mineral surfaces had a PbO species and minor amounts of Pb(OH)2 and antimony was oxidized on the stephanite and pyrargyrite surfaces during leaching. There was a much greater concentration of Sb(V) on stephanite relative to pyrargyrite. Therefore, lead forms a redox couple on silver mineral grains and favors the oxidation of silver minerals. The high-grade Kupol sample assayed 22.6 g/t Au and 359.3 g/t Ag following treatment by gravity separation. Gold and silver extractions from the Kupol sample were 94.5% and 82.9%, respectively, using 500 ppm NaCN and 250 g/t lead nitrate. The findings to improve the extraction of silver from the ore sample with lead nitrate addition were congruent with those to improve the extraction of silver from the individual high purity minerals. Pretreatment did not, however, improve gold or silver extraction significantly with the ore sample.

Jan 1, 2011

By O. Babak, O. Leuangthong, M. A. Cuba

Integration of data from multiple sources and/or multiple scales is a common, yet challenging aspect of geostatistical resource modeling. Common approaches to data integration are based on a cokriging framework that assumes a consistency of scale in the information that leads to a requirement to composite the data prior to model construction. It is well known that the geostatistical model parameters are scale dependent. In particular, the volume variance of integrating these various scales has a direct impact on the semivariogram that should be used in model construction and/or the assessment of volume-variance relations as it affects resource estimation. This paper reviews and compares two different approaches for semivariogram upscaling. The first approach is the scaling laws. It is an empirically derived approach, involving several simplifying assumptions, one of which is a strict assumption of invariance of the semivariogram shape. The second approach is a theoretically derived direct upscaling of the semivariogram. This approach has been around for a number of years, but is seldom implemented due to software limitations. In this paper, we present a numerical integration approach to facilitate direct semivariogram upscaling. The advantage of direct upscaling over the scaling laws approach is shown by considering a synthetic example and a case study. Further, in the case of multiple codependent random variables, the extension of the direct semivariogram upscaling to the cross semivariograms is derived and an upscaled consistent linear model of coregionalization is presented.

Jan 1, 2013

By Ewald H. Kurt

The story of America's progressing standard of living is the story of machines. The automobile, the airplane and the telephone for example have made our transportation and communication systems what they are today. Even they depend in turn on another machine -- the rock drill. By making it possible to economically mine and quarry minerals in large quantities, this versatile machine supports virtually every American industry relying on the earth for its buried raw materials. And, like all machines, the rock drill's mechanical evolution was stimulated by production demands placed upon it. All percussion drills are mechanized versions of the original drilling unit -- man, Figure - illustrates a double jack team at work before the turn of the century. The man with the sledge hammer is the impact device while the man sitting is the rotation mechanism and feed motor. The first drifter drills (Figure 2) performed the same function but with increased mechanical efficiency. A piston controlled by a valve produced impact. A built-in ratcheting mechanism provided rotation and a hand-cranked screw provided feed thrust. As the industrial revolution proceeded into the twentieth century, the demand for raw materials stimulated refinements of all recovery machinery, including rock drills. As drills became heavier and more powerful, a mounting (or carrier) had to be provided to move the drill from hole to hole. This resulted in the development of the wagon drill (Figure 3). Propelled by muscle power, the wagon drill was for years the standard tool of the surface drilling industry (Figure 4). As drills penetrated faster and as labor increased in cost, the time consumed in nondrilling peripheral operations had to be

Jan 1, 1977

By Peng Gao

Coal-based reduction followed by magnetic separation is an innovative technology used in processing refractory iron ores. Given that size is essential to the separation of the metallic iron from the gangue, the morphology of metallic iron particles and their evolution during coal-based reduction are investigated in the present work. The size of the metallic iron particle increased from 128.76 µm to 565.70 µm when the reduction time increased from 20 min to 60 min at 1,225° C and C/O (i.e., the amount of coal addition in terms of the gram-atomic ratio of the fixed carbon in the coal added to the combined oxygen in iron oxides) of 2.5. Based on our microstructural and metallographic analysis, the iron ore reduction process can be divided into three stages: (1) metallic iron particle formation, (2) iron oxide reduction and metallic iron assembly and (3) metallic iron particle growth. Almost all iron oxides are reduced to metallic iron in the second stage. These newborn metallic iron particles are energetically active and able to assemble and grow, and are eventually separated from the gangue. The large metallic iron particles benefit the subsequent magnetic separation process.

By John M. Gullbert

It is the task of this portion of today's session on the new meaning of regional tectonics in the search for ore districts to discuss known interactions of tectonics and ore deposition in the 'new global tectonics' context. I will speak particularly about known applications of the recent tectonic advances to ore finding. Stated yet another way, it's getting on in time toward the "put up or shut up" stage-¬and I would not be here if I thought that the new tectonics were not an effective present matrix for ore finding. Before delving into specific geologic relationships--and I propose to discuss mainly the evolution of an idea which may reveal the presence of a major copper deposit on mainland Mexico--I must note that there have been no published accounts that I know of which assert that a particular discovery has been made soley and specifically because of an interpretation based upon mechanisms directly linked to sea floor spreading or plate tectonics. It is nonetheless true" that several major exploration efforts are based upon such interpretations, and, as is normal when exploration ideas are involved, one does not wish to call attention to an advantageous position in a highly competitive business. Little might be expected to have been announced in so fast-moving and potentially lucrative an area. Another point which needs to be made is that people such as B. S. Butler (1933), Billingsley and Locke (1935 and 1941), Harrison Schmitt (1935), and more recently Mayo (1958) have been working for decades with the tectonic expressions of the emergent tectonics without recog¬nition of the driving forces or the unifying tectonic concepts

Jan 1, 1971

By J. O. Marsden

This paper presents an overview of the innovative methods for gold and silver extraction that have been put into actual practice in North America since 1987. It is an update of a paper of the same title which was presented by Sass and Mansanti at the AMC conference in San Francisco in 1987. New practices, new equipment and variations of older practices that have been introduced in the last five years are discussed in each of the following categories: process selection trends, comminution, gravity concentration, flotation, oxidation, agitated and vat leaching, heap leaching, solution concentration and purification, zinc precipitation, electrowinning, tailings disposal detoxification, and reclamation.

Jan 1, 1993

By R. Bissonette, C. Sunderman, R. Jacksha

The ability of wireless systems—e.g., voice communication, proximity detection, tele-remote operation, telemetry, etc.—to function satisfactorily (coexist) in the presence of other wireless systems is critical to the safety and health of mine workers. The failure of wireless systems to coexist could result in the delay, corruption, or outright loss, of critical data, voice, or video information. However, no mining-sector-specific regulations, standards, or guidelines exist to ensure the safe coexistence of wireless systems. This paper introduces the concept of wireless coexistence, implications in the mining industry, and the National Institute for Occupational Safety and Health’s (NIOSH’s) research approach to develop guidelines and recommendations to ensure safe wireless coexistence.

Feb 1, 2023

By Alan D. Randolph

A size-continuous breakage kinetics model is postulated and supported with industrial grinding mill data. It is shown that the kinetics parameters include the effects of possible classification at the mill discharge. The estimated parameters were then used in the kinetics model to simulate the behavior of a grinding mill in open and closed circuit operation. While material transport and kinetics are equally important in open loop operation, heavy recycle in a closed circuit make a detailed material transport model for grinding unnecessary. In effect, the mill can be considered as backmixed. This suggests that more emphasis should be placed on modeling the classifier than the development of detailed material transport models for the grinding mill.

Jan 1, 1975

By X. Wang, Y. Luo

The propensity of coal spontaneous combustion can be evaluated using various laboratory testing methods, such as R70 adiabatic tests, thermal gravimetric analyzer (TGA) tests and critical self-heating temperature (CSHT) methods. Each of the methods has its unique characteristics and index for classifying the propensity of self-ignition of coals. Accountable relationships among the propensity indices of different methods should be established. Using the newly established R70 and TGA testing setups in our ventilation laboratory, samples from U.S. coal mines have been collected and tested. The TGA is a relatively new quantitative method. A test can be conducted in a relatively short time, within about one and a half hours, compared to the adiabatic tests. The temperature and weight of the sample can be measured with high precision and then used to determine the activation energy of the coal, which is a good indicator of the potential for self-heating. Under a specific experimental design, the TGA technique could perform the proximate analysis for determining coal quality parameters (e.g., moisture, volatile matter, fixed carbon and ash content). These parameters can be used in an empirical equation for assessing the potential for coal self-ignition. The trend of activation energies determined using TGA techniques is reasonably consistent with the trend of activation energies determined using adiabatic tests. As a case study, a comparative analysis of these two methods for determining activation energy was made on coal samples collected from Indiana. The kinetics of the spontaneous combustion mechanism has been explained. If the functional groups of a coal such as hydroxyl (-OH), carboxyl (-COOH), methyl (-CH3), etc., activate more easily with a small amount of activation energy at a relatively low temperature, the coal will have a higher potential for self-heating. With the kinetic and coal quality parameters determined by the TGA setup, it has been found that the coal with a low potential for self-ignition has low self-heating rate, a high activation energy and a high minimum self-heating temperature.

Jan 1, 2012

By Mostafa Benzaazoua, Bruno Bussière, Mukendi Kongolo

The desulphurization process has been proposed over the last few years for acid mine drainage control at certain mines, which generate low to medium grade sulphidic tailings (-3 to +25 wt% S). The environmental sulphur recovery, which means the sulphur to be floated to produce a non-acid generating final tailings, depends mainly on the intrinsic neutralizing potential of the tailings. However, in some cases the sulphur cleaning is complicated by other parameters which affect the flotation probability of the sulphide particles. In this study, a number of tests were conducted with a Hallimond tube and Denver Cell on both pure mineral and mine tailings. To develop a better understanding of the mechanisms of non-selective sulphide flotation, three types of approach were investigated in this work: (i) pure pyrite at progressive milling degrees, (ii) artificial mix of pyrite and quartz at different calibrated granulometry and (iii) same composition tailings with 26 % wt sulphur at progressive milling degrees. The effect of the granulometry on the sulphide flotation was demonstrated both. The results allow us to define a granulometry model, which can then be considered in the whole desulphurization modeling.

Jan 1, 2000

By F. J. Sotillo

The objective of this investigation was to determine the feasibility of using a high-pressure roll mill (HPRM) to improve the separation efficiency of dolomite from apatite in downstream operations when treating high-dolomitic pebbles. High-dolomite samples from four phosphate mines were used for the test program. The research work plan included sample characterization studies; INSTRON tests to develop preliminary crushing data; high-pressure roll mill evaluations to determine crushing parameters, such as feed rates, rolls speed and gap, and applied torque, pressure and energy; and screen, microscopy, and flotation studies to assess dolomitelapatite separation efficiency. The results of the HPRM tests show that commercial products for all four mines can be obtained. Recoveries of 74-82% of the P2O5 and rejections of 46-83% of the MgO were reported with an specific energy consumption of 0.2-0.5 of that of a laboratory rod mill.

Jan 1, 1998

By T. L. Barone, J. R. Patts, L. D. Patts, S. J. Janisko

"Controlling float coal dust in underground coal mines before dispersal into the general airstream can reduce the risk of mine explosions while potentially achieving a more effective and efficient use of rock dust. A prototype flooded-bed scrubber was evaluated for float coal dust control in the return of a continuous miner section. The scrubber was installed inline between the face ventilation tubing and an exhausting auxiliary fan. Airborne and deposited dust mass measurements were collected over three days at set distances from the fan exhaust to assess changes in float coal dust levels in the return due to operation of the scrubber. Mass-based measurements were collected on a per-cut basis and normalized on the basis of per ton mined by the continuous miner. The results show that average float coal dust levels measured under baseline conditions were reduced by more than 90 percent when operating the scrubber. IntroductionAirborne coal dust is a byproduct of coal production, and engineering controls exist to deal with both the respirable dust health hazard as well as the float dust explosion safety hazard. Float coal dust, smaller than 75 µm (0.003 in.) in size, can deposit throughout mine entries and propagate explosions that had been initially fueled by methane gas. The inertization of float coal dust with rock dust helps prevent a potential secondary float coal dust explosion, but a preferable course of action is to significantly reduce the hazard by removing float coal dust from the airstream before it has the opportunity to deposit on the mine’s surfaces.Since 1970, disasters due to explosions in underground coal mines have caused 201 deaths in the U.S. mining industry, including 29 deaths in a single mine explosion in 2010 (Wade, 2010; U.S. Mine Safety and Health Administration, 2015). The U.S. National Institute for Occupational Safety and Health (NIOSH) had initiated a fiveyear research project that aims to investigate methods and technologies to reduce the potential for secondary coal dust explosions by the purposeful capture and/or suppression of float coal dust prior to its deposition on the mine roof, rib and floor (NIOSH, 2013). The project aims to evaluate the efficiency of methods to reduce longwall and belt airway float dust in the general airstream as well as methods to capture it at or near the source. Prioritization is given to longwall sections given the amount of coal produced relative to continuous miner sections, but the research is open to technologies that may be adapted from one method of mining to another."

Dec 1, 2016

By Roberto Fustos, Gonzalo Nelis, Víctor Sanhueza, René Gómez

Hang-ups are a challenging operational problem in block caving mines. They interrupt ore flow and imply hang-up removal activities, which take time, increase operational costs, and involve safety risks for workers. In block caving, the number of hangup events of mechanical arches that appear in the drawbell could be decreased if the drawbell geometry is adequately designed based on the expected rock fragmentation. Here, we compile and analyze hang-ups reported in several block caving mines to evaluate the impact of drawbell geometry, rock size, and vertical load on hang-up frequency at the mine scale. Results show that the ratios between drawbell length and d80 (dL/d80), between drawbell width and d80 (dW/d80), between drawbell volume and rock volume (VDB/VP), and vertical stress are critical parameters that define hang-up frequency. These findings confirm previous experimental studies, where a decrease in hang-up events is associated with an increase in these ratios. Additionally, these outcomes are used in a support vector machine algorithm to define categories of hang-up frequency. The results of this classification algorithm are presented in diagrams, which can be used to estimate the hang-up frequency in block caving projects.

Oct 15, 2022

By Clement K. Chase

Since the dam of cyanidation leaching techniques for precious metals, certain manganese-bearing silver ores have been a problem due to low silver extractions. Since simultaneous occurrence of silver and manganese is common in nature, this situation has made many otherwise attractive silver deposits uneconomic in the past. Several older techniques have been useful but at $1.29 per ounce of silver, the economics were unfavorable. With the new look in silver prices and some improvements in processing technology, neglected silver districts offer new promise.

Jan 1, 1981

By D. K. Steele

The U.S. Bureau of Mines has investigated the recovery of metals from copper industry wastes by sulfuric acid leaching in a semi-continuous, bench-scale system to solubilize arsenic, copper, and molybdenum. Leach residues contained approximately 40 wt pct PbSO4, suitable for processing at a lead smelter. Arsenic and molybdenum removal from leach solution was examined using solvent extraction with tri-n-butyl-phosphate (TBP), and copper was subsequently recovered by cementation. Bleed electrolyte from a copper refinery was determined to be a viable source of acid for the initial leach stage.

Jan 1, 1991

By Miguel Reyes, Chenming Zhou, MATTHEW GIRMAN

Electromagnetic energy emitted from electronic devices has been known to interfere with other electronic systems, hindering their ability to function properly. Mines have many electronic devices critical to the health and safety of mine workers that could be negatively affected by electromagnetic interference (EMI). To ensure that devices are electromagnetically compatible, tests must first be conducted to measure emissions and check for immunity. There are many standards available across multiple industries that prescribe emission limits and test methods for electronic devices. Due to the unique environment of an underground mine, it may not be enough to simply adopt a standard from another industry to mining. A literature review has been conducted, and an overview of EMI standards in other industries will be provided in this paper. Also, an example of how a standard can be applied to mining equipment is presented. Finally, recommendations on standards which could potentially be applied to mining will also be included. This work will inform the mining industry of EMI standards in other industries so that mine workers and technology manufacturers have guidance of the steps that can be taken to investigate and reduce the impact of electromagnetic interference and potentially work toward electromagnetic compatibility. The findings and research involved in this effort can also be used to explore the need to develop mining-specific EMI recommendations and standards.

Nov 25, 2021

By Alvaro Veizaga, Samuel Cuellar

In recent years, Industry 4.0 has generated a change in the way companies in various industrial sectors design, produce and deliver products and services, and is focused on the interconnection of systems, the advanced access and management of large amounts of data in real time, and the implementation of emerging technologies such as the Internet of Things (IoT). Artificial intelligence (AI), machine learning (ML), digital twins (DT), robotics, virtual and augmented reality (VR/AR), among others [1]. DTs are accurate and dynamic virtual models that replicate physical systems, where it is possible to simulate and optimize operations before implementing real-world changes [3]. These features make it possible to reduce investment costs, minimize risks and improve strategic decision-making. These benefits are of utmost importance for tailings storage facilities (TSF), since they are facilities aimed at the safe storage of tailings and with the constant need for growth [4]. This paper evaluates the applicability of a DT in a TSF from a conceptual perspective, providing the advantages of its implementation, but also the barriers identified in the industry based on the authors’ experience.

Feb 1, 2025

By Adil Jamali, Taufiq Hidayat, Imam Santoso, Zulfiadi Zulhan, Indah Suryani

The study investigates the segregation of iron and titanium in iron sand concentrate pellets reduced using coal under an isothermal-temperature gradient profile. The results show that metallic iron migrates to the surface while titanium and other oxides move to the center of the pellet. The study provides insights into the reduction process and the behavior of iron and titanium during heat treatment.

Mar 2, 2022

By Jürgen. F. Brune, CLAIRE STREBINGER, ADITYA JUGANDA, Gregory E. Bogin Jr

The abstract highlights the risk of methane gas explosions in underground coal mines and the potential of computational fluid dynamics (CFD) modeling to simulate such events and assess their impact on mine ventilation. The study focuses on developing CFD models for large-scale explosions in longwall mines, specifically simulating methane gas explosions resulting from face ignition during coal cutting. The research demonstrates the integration of a combustion model into a longwall mine ventilation model and shows how the availability of explosive gas mixtures significantly affects flame propagation and explosion pressure.

Mar 27, 2022