Search Documents

By ?. ?ivkovic

The silicate slag and copper matte that are the byproducts of smelting copper in a reverberatory furnace contain SiO2, FeO, Fe3O4, CaO and Al2O3, and Cu, Fe and S, respectively. These components influence the oxide (Cuox), sulfide (Cusul) and total (Cutotal) copper content lost in the waste slag. This paper uses multiple linear regression analysis (MLRA) to determine the degree of influence. The results of calculations obtained using MLRA were compared to actual measured results and found to have a large degree of correspondence, with the coefficient of determination R2 = 0.975. These results indicate that slag composition and copper content in the matte influence the copper losses in the waste slag with a probability of above 97%. It was determined that, of the total copper content of the slag, 74% is in sulfide and 26% in oxide form, and that this ratio is not dependent on the slag or matte composition.

Jan 1, 2010

By P. H. S. W. Kulatilake, T. Hudaverdi, C. Kuzu

Prediction of blast fragmentation plays a key role for overall productivity of mines. In this study, a new multivariate analysis procedure for prediction of blast fragmentation is presented. Several blasts performed in various mines and rock formations worldwide were brought together and evaluated. An extensive blast database was created. Blast design parameters, the modulus of elasticity and in-situ block size were considered to perform multivariate analysis. A complete multivariate analysis procedure was applied in three steps. First, a hierarchical cluster analysis was used to separate the blast data into different groups of similarity. Two different groups were formed based on the elasticity modulus values. In the second step, group memberships were checked by discriminant analysis. The dominant parameters of the occurrence of the groups were determined. Also, discriminant analysis was used to determine the group membership of the respective blasts. As the last step, the multivariate regression analysis was applied to develop prediction equations for estimation of the mean particle size of muckpiles. Two different prediction equations were developed based on the rock stiffness. Validation of the proposed equations on various mines was performed. Prediction capability of the proposed models was found to be strong. The models are not complex and are suitable for practical use at mines.

Jan 1, 2011

By Thibaut Pannetier, Damien Rogat, Catherine Larive, André Regnard, David Chamoley

"INTRODUCTION For several decades, the use of fibre-reinforced sprayed concrete (FRSC) has been becoming increasingly widespread, either as a replacement for or in addition to traditional reinforcements. Macro-synthetic fibres appeared on the market at the same time as metal fibres (in the 1980s), but their use has developed more recently in France, starting in the early 2000s. While their properties are attractive for underground operations, their long-term performance remains the subject of some controversy, particularly with regard to the phenomenon of creep [1-5]. Unfortunately, the many differences of protocol among the studies carried out (materials, metering, spraying equipment and test methods, etc.) mean that, in general, the results cannot be compared. Although several methods have been developed to assess the bending creep behaviour of fibre-reinforced concrete, the majority of them test notched beams resting on isostatic supports. There are currently no standardised test methods adapted to FRSC on hyperstatic supports (as is the case for FRSC used for underground support). The Asquapro association has thus developed a new test specially designed for this type of concrete. Slabs of thickness 10cm, measuring 60 x 60 cm in plan have been sprayed and tested under bending stress according to a test procedure inspired by the standardised test of energy absorption capacity (NF EN 14488-5). An experimental campaign was launched in October 2014 to study the behaviour of seven types of sprayed concrete, manufactured using the same concrete matrix: six of them were reinforced with different metal or macrosynthetic fibres and the seventh with a welded wire mesh. Fourteen slabs were sprayed for each type of concrete and also for the non-reinforced concrete with the same matrix. The types of mechanical performances measured were the compressive strength and energy absorption capacity (at seven and twenty-eight days), in addition to the creep behaviour of these seven types of concrete, placed under stress on the seventh day. This article follows on from that published in the WTC 2015 congress proceedings [6]: the programme and the test methods are briefly described here and the results available at the time of writing are presented and discussed."

Jan 1, 2016

By Ralph van Rijswick, Erik Vlot

"Anglo American operates 18 Weir GEHO piston diaphragm pumps (PD) in the two pump stations of the 52-km (32-mile) long Minas Rio iron ore concentrate pipeline. The pipeline is designed to transport 26.5 Mt/a (29.2 million stpy) of concentrate from the mine to the export terminal at the coast.During the commissioning of the pipeline in the fall of 2014, high pressure pulsation levels were experienced, with peak-to-peak levels as high as 20 bar. Based on pressure readings it was concluded that hydraulic resonances were present in the system, which were excited by the third and sixth harmonic of the flow pulsation generated by the pumps.Based on this observation, Weir Minerals Netherlands, manufacturer of GEHO PD slurry pumps, recommended installing a phase shift controller that controls the phase shift between the crankshafts of the individual pumps, thereby minimizing the effect of the hydraulic resonances.GEHO piston diaphragm pumps and pressure pulsation analysisPiston diaphragm pumps are used worldwide to transport abrasive and/or aggressive slurries against high discharge pressures in the mining, mineral processing and power industries. The basic operating principle of a piston diaphragm pump is shown in Fig. 1.A crankshaft is driven by an external electric motor via a gearbox. The crank mechanism transfers the rotating motion of the crankshaft into a reciprocating motion of the piston. The piston displaces a hydraulic fluid, called the propeling liquid, which displaces an elastic rubber diaphragm. When the piston moves to the right, the pressure in the pump chamber drops below the suction pressure and the nonreturn valve on the suction side will open, allowing the pumped fluid to flow into the pump chamber. When the piston moves to the left, the fluid is compressed, and when the pump chamber pressure rises above the pipeline pressure, the nonreturn valve on the discharge side will open allowing a displacement of fluid into the discharge line. The main objective of the diaphragm is to isolate the piston and the drive mechanism from the abrasive and/or aggressive fluid and create a hermetic seal between the pumped fluid and the ambient environment. Piston diaphragm pumps as shown in Fig. 1 are among the largest positive displacement pumps in the world and have been produced with stroke volumes of up to 100 L (26 gal) per pump chamber for flow rates up to 800 m3/h, discharge pressures up to 250 bar and hydraulic outputs over 2 MW per unit (van Rijswick et al., 2010)."

Jan 9, 2017

By David B. McWhorter

Conventional analyses of seepage through saturated media do not apply when tailings impoundments are located above a partially saturated zone. Three stages of seepage are identified and methods for estimating the seepage rates and duration of each stage, based upon flow in partially saturated and saturated porous media, are demonstrated. The effectiveness of earthen liners is discussed and procedures for estimating the required properties of the porous media are provided.

Jan 1, 1978

By Valeh Aghazadeh, Shima Barakan, Mina Soleymani, Ehsan Bidari, Morovvat Faridazad

Molybdenite is the most important molybdenum concentrate, which is mainly recovered as a by-product from porphyry copper deposits. Due to the low efficiency of purification processes such as flotation in the reduction of copper content of molybdenum concentrate to a standard level (i.e., less than 0.5 wt.%), further purification by a hydrometallurgical method is required. Although different types of chemical reagents were found to be effective in the leaching of copper minerals from molybdenum concentrate, the mechanisms of these processes remain largely unexplored. In this study, optimal conditions for maximum copper leaching (> 99%) were obtained at the concentration of HCl = 1 M, FeCl3 = 0.5 M, CuCl2 = 0.05 M, CaCl2 = 0.5 M at 75 °C, 500 rpm, and S:L = 1:10 during 60 min. CuCl2 was identified as the most effective leaching reagent for copper dissolution in agreement with Visual MINTEQ model results due to the formation of various types of copper chloride complexes. Furthermore, the electrochemical behaviors of FeCl3, CuCl2, and CaCl2 reagents before and after the leaching process were investigated by the cyclic voltammetry technique. The results of cyclic voltammograms at different scan rates verified the presence of copper chloride complexes, and ferric ions as the oxidizing reagents for better dissolution of copper sulfides. Based on kinetic study results of shrinking core models, both chemical and diffusion reactions controlled the copper leaching process with an obtained activation energy of 33.56 kJ/mol. For recovery of the leached copper, the precipitation process was done by the addition of Na2S at 45 °C, S/Cu = 1, and pH = 9.

Dec 26, 2022

By D. R. Willmer, E. J. Haas

"DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT This study analyzed the publicly available health and safety policies of 26 mining companies to determine the quantity of health and safety (H&S) practices that mining companies encourage in relation to the Plan-Do-Check-Act cycle. A thematic content analysis of the policies identified elements and practices within the text. On average, companies communicated information on about 7 elements (range 1–14, standard deviation = 3.49) and discussed 15 practices (range 2–34, standard deviation = 9.13). The elements in which companies highlighted the most practices were risk management, emergency management, leadership development, and occupational health. A discussion of the policy trends shows areas that mine sites can improve upon within their Plan-Do-Check-Act cycle, in addition to encouraging the use of both leading and lagging indicators to manage health and safety performance. INTRODUCTION Mining companies and their employees are expected to identify and manage risks at their worksites to ensure the health and safety (H&S) of everyone at the site. The primary mechanism in place to control these risks is a company’s health and safety management system (HSMS) (Boyle, 2012). Broadly, an HSMS is a set of standard, interrelated, and interacting elements used to promote and achieve occupational H&S goals (ANSI/AIHA Z-10, 2012; BS OHSAS 18001, 2007). The practices conveyed within an HSMS are expected to minimize incidents, injuries, illnesses, and even save worker lives (Alsop and LeCouteur, 1999; Arocena and Núñez, 2010). In the United States, both the Occupational Safety and Health Administration (OSHA) and Mine Safety and Health Administration (MSHA) regulate and encourage aspects of an HSMS (US Federal Register, 2011, 2010). Many HSMS documents (i.e., Chemical Industries Association, 1995; Health and Safety Executive [HSE], 1995; International Labour Office [ILO], 2001) attribute the source of their basic management system to Deming’s Plan-Do-Check-Act (PDCA) model of continuous quality improvement and organize their practices within this cycle (Johnson, 2002). The PDCA cycle is a well-adopted approach in health and safety management and promotes continuous learning and adaptability (Robson et al., 2007)."

Jan 1, 2018

By L. J. Lindsay

Kaiser Resources Ltd. operates a coal mining complex in Southeastern British Columbia. A large surface mine, a conventional underground mine, and an innovative hydraulic underground mine are presently in operation. The products of these mines are fed to the Elkview plant. This coal has to be prepared to 9. 5% ash and 6'o total moisture for export from the port of Roberts Bank near Vancouver, British Columbia to Japan at a rate of 4. 5 Mltpy. The moisture requirement for the coal product was recently increased to 8. 0% total moisture. The entire operation has been described in various publications (1), (2), (3). Details of the venture will not be repeated in this paper. In this paper we hope to describe the modifications made to the original coal preparation plant in order to satisfy market requirements for quality and quantity of coal.

Jan 1, 1974

By D. K. DeForest

The olfactory system (sense of smell) is crucial to the ability of fish to avoid predators, recognize kin, and synchronize reproduction (Baldwin et al. 2003). Copper (Cu) has been shown to impair olfaction in juvenile freshwater life stages of salmonids (including Pacific salmon and trout) in some laboratory experiments; and in the United States, public concerns have been expressed that current regulatory criteria for Cu in fresh water are not adequately protective of olfactory function in salmonids (e.g., OSU 2007; Pearson 2007). These concerns have largely been raised because some Cu concentrations that have caused olfactory impairment in salmonids in the laboratory are less than Cu concentrations that have been shown to reduce salmonid survival, growth, or reproduction (the effects endpoints that are typically considered in deriving ambient water quality criteria). However, two important and interrelated points that must be considered: (1) freshwater Cu criteria are "driven" by the sensitivities of several invertebrate species that are more sensitive than the olfactory impairment threshold in salmonids when (2) the influence of water chemistry on Cu bioavailability is properly considered in deriving Cu criteria. Bioavailability refers to the ability of various chemical forms of Cu to interact with receptors on the surface(s) of organisms and thus directly cause toxicity or uptake by the organisms. The toxicity of Cu and other metals to aquatic organisms is a function of water chemistry. For example, acute Cu toxicity in fresh water generally decreases as pH, water hardness (Ca2+ and Mg2+), alkalinity, and dissolved organic carbon (DOC) concentrations increase (Meyer et al. 2007). The U.S. Environmental Protection Agency (USEPA) has recommended hardness-based freshwater aquatic life criteria for Cu and other metals since the 1980s (e.g., USEPA 1985); and hardness-based metals criteria decrease (i.e., become more restrictive) as water hardness decreases. More recently, the USEPA has recommended freshwater aquatic life criteria for Cu based on the biotic ligand model (BLM; USEPA 2007), which accounts for the influence of multiple water chemistry parameters, including DOC, pH, alkalinity, Ca2+, Mg2+, and several other cations and anions. The BLM-based Cu criteria generally decrease as DOC concentration, pH, alkalinity, and water hardness decrease. Because DOC has a stronger influence on Cu bioavailability than water hardness, hardness-based and BLM-based Cu criteria can differ considerably. For example, in water that has low DOC and high hardness, the hardness-based Cu criterion would be relatively high (because it is driven by the high hardness) but the BLM-based Cu criterion would be relatively low (because it is driven by the low DOC). Thus, any evaluation of the protectiveness of Cu criteria against a given effect, such as olfactory impairment, must properly account for the chemistry of the exposure water. Meyer et al. (2013) compiled data on Cu-induced olfactory impairment and olfactory-induced behavioral effects from tests in which BLM parameters were measured. They demonstrated that the USEPA's BLM-based freshwater life criteria for Cu are protective against olfactory impairment, because it adequately accounts for water chemistry (whereas the USEPA's hardness-based Cu criteria are not consistently protective). Olfactory impairment by Cu is now receiving increased attention in Canada and Europe (e.g., Wall 2013; Stang 2013). Accordingly, in this paper we have expanded the analysis of Meyer et al. (2013) to consider copper guidelines from various other countries and whether these guidelines are protective against olfactory impairment.

Feb 23, 2014

By Harold J. Schock

The cases of no auxiliary ventilation and ventilation with tubing were mathematically modeled, using a turbulent dispersion model. The scooptram that is used to load is modeled as a variable-speed, variable-strength source of pollutants moving in and out of the dead-ended drift. Model predictions are compared to experimental measurements. A parametric analysis was performed to determine the effect of exhaust pipe location and time spent out of the drift, as well as to determine if a relationship existed between CO2 and NO levels. It was concluded from this analysis that when modeling a load-haul-dump cycle, it is necessary to use a model that has the capability of predicting changes in source strength as well as source location. It was also determined that four relevant factors include effective heading height, apparent longitudinal diffusion coefficient, transverse concentration gradient at the face, and average dispersion width of the exhaust jet. As these factors change with heading geometry and ventilation configuration, they were determined experimentally, Carbon dioxide was used as a tracer to calibrate the model; since, knowing the fuel flow rate, it is possible to calculate CO2 production. The above four factors in the computer model were calculated using a regression analysis, comparing predicted local concentrations to measured local concentrations. The model was then verified after this calibration process using additional experimental results. With the calibrated model, it is possible to predict pollutant concentrations at any location in the heading using an engine map and the previously calculated flow field. A parametric analysis shows that the exhaust pipe location can have a significant impact on operator exposure to exhaust gases. It was also shown that NO concentration varies directly with C02 levels. Predictions using the dynamic model are contrasted with constant source strength (pollutant flow rate) results. An analysis of these predictions for computing time-weighted average NO shows the dynamic model predictions of operator exposure to this pollutant to be less than one-half of the value predicted using a constant source model.

Jan 1, 1981

By A. D. Hammond

Vanadium is a transition metal, ductile and silver-gray. It is harder than most metals and steels and it has a good resistance to corrosion. It is stable against alkalis and sulfuric and hydrochloric acids. Vanadium is oxidized in air at about 660° C (1,220° F), although an oxide layer forms even at room temperature. The chemistry of vanadium is noteworthy for the accessibility of the four adjacent oxidation states, 2-5. In aqueous solution, the colors are lilac V2+, green V3+, blue VO2+ and, at high pH, yellow VO42-. Considered to be as abundant as zinc, metallic vanadium is not found in nature, but it is known to exist in about 65 different minerals. Economically significant examples include patronite (VS4), vanadinite (Pb5(VO4)3Cl), associated to the uranium mineral carnotite (K2(UO2)2(VO4)2?3H2O) and in a vanadium mica called roscoelite K(V3+,Al,Mg)[(Si,Al)4O10] (OH)2. Other important vanadium ore oxides are montroseite (V,Fe)O(OH) and corvusite (Na,Ca,K)V8O2.4H2O. Much of the world?s vanadium mine production comes from magnetite-hosted deposits and, to a lesser extent, sedimentary-hosted sandstone.

Dec 1, 2013

By D. R. Willmer, E. J. Haas

As national and international health and safety management system (HSMS) standards are voluntarily accepted or regulated into practice, organizations are making an effort to modify and integrate strategic elements of a connected management system into their daily risk management practices. In high-risk industries such as mining, that effort takes on added importance. The mining industry has long recognized the importance of a more integrated approach to recognizing and responding to sitespecific risks, encouraging the adoption of a risk-based management framework. Recently, the U.S. National Mining Association led the development of an industry-specific HSMS built on the strategic frameworks of ANSI: Z10, OHSAS 18001, The American Chemistry Council’s Responsible Care, and ILO-OSH 2001. All of these standards provide strategic guidance and focus on how to incorporate a plan-do-check-act cycle into the identification, management and evaluation of worksite risks. This paper details an exploratory study into whether practices associated with executing a risk-based management framework are visible through the actions of an organization’s site-level management of health and safety risks. The results of this study show ways that site-level leaders manage day-to-day risk at their operations that can be characterized according to practices associated with a risk-based management framework. Having tangible operational examples of day-to-day risk management can serve as a starting point for evaluating field-level risk assessment efforts and their alignment to overall company efforts at effective risk mitigation through a HSMS or other processes.

Jan 1, 2016

By İbrahim Çınar, Hakan Özşen

Mine workers in heavy and dangerous work are under several physical risk factors, for example temperature, humidity, noise, vibration, lighting and air velocity. Thermal comfort includes parameters such as air temperature, air humidity, air flow rate, radiant heat, metabolic rate and garment insulation. In this study, thermal comfort conditions were evaluated using thermal comfort indices defined as predicted mean vote (PMV) and predicted percentage dissatisfied (PPD) which were determined by measurements taken from an underground coal mine for approximately 100 days. Although the metabolic rate (light work) was kept at 2 met, it was found that predicted mean vote ranged between − 2.58 and 1.68. The predicted percentage dissatisfied index was found to reach 95%. According to the results, it can be seen that thermal comfort may have negative effects on occupational health and safety. The change in thermal comfort index values in the Soma Underground Coal Mine was investigated in detail and the reasons for the changes were determined. Furthermore, determining the optimal working environment for the mine workers was also an aim of this study.

By K. V. Raj, M. McNinch, A. L. Miller, J. Wilson, D. A. Parks

Diesel particulate matter (DPM) has been shown to contribute to various adverse health effects on underground miners. In order to reduce worker exposures, it is critical to measure the levels of DPM in the active work settings and in real time. However, the 5040 method, developed by the National Institute for Occupational Safety and Health (NIOSH), which quantifies the mass of elemental carbon (EC) and organic carbon (OC) in the samples, is based on full-shift samples, and can take days or even weeks for results. Use of real-time monitors could significantly reduce the risk of DPM exposure to miners, and available monitors have been shown to quantify DPM, mainly using the EC and other surrogates. The NIOSH Spokane Mining Research Division is conducting research aimed at developing a field-portable DPM monitor that is able to quantify both EC and OC. One part of this work is to understand the effect of OC on currently available real-time DPM monitors. This paper will present the results from experiments that were designed to observe the effect of OC on real time monitors and compare the results with the NIOSH 5040 method. BACKGROUND Diesel engines remain ubiquitous in mining environments and, as such, are one of the primary sources of ultrafine- and nano-aerosols in the mining environment in the form of diesel particulate matter (DPM). As a result of their small size, DPM has longer residence times in a mine atmosphere than the typically larger mechanically generated dust [1]. In addition, the small size enables DPM to penetrate deeply into the respiratory system [1], and exposure to DPM has been shown to contribute to various adverse health outcomes of the pulmonary system [2] and cardiovascular system [3]. Diesel exhaust has been classified as a carcinogen to humans (Group 1) by the International Agency for Research on Cancer [4]. Due to mounting concern about adverse health outcomes, extensive efforts are being made to reduce workers’ exposure to DPM, with the high exposures that often occur in underground mines being of particular concern [5]. New technologies are being developed to reduce engine emissions and thereby airborne DPM levels, including advanced engine technologies, a host of aftertreatment systems [6], and a variety of alternative fuels. The latter have been shown to markedly decrease respirable DPM and other hazardous components of diesel emissions from mining vehicles [7], yet high exposures persist, especially in underground mines [8]. In order to reduce worker exposures, it is critical to measure the levels of DPM in active work settings. In mine settings, exposures to DPM are measured by collecting air samples on filters (usually full-shift samples) and sending them to a lab for analysis using the Mine Safety and Health Administration (MSHA) P13 method, a variant of the National Institute for Occupational Safety and Health (NIOSH) 5040 method. The 5040 method is designed to quantify the mass of elemental carbon (EC) and organic carbon (OC) on the samples [9], which is then used to determine the concentration in the sampled air. MSHA has set a limit for exposure, which is based on the concentration of total carbon (TC), or the sum of both EC and OC. The allowable TC in the air (time-weighted average over the shift) is 160 μg/m3 of TC [10].

Jan 1, 2019

By I. Raposo, I. Moreno-Ventas, A. Palma, M. J. Díaz, M. Vázquez

The oxidative degradation kinetics of chalcopyrite have been studied by thermogravimetric analysis (TGA). The obtained data are necessary for the kinetic description of the flash fusion process, which can contribute to the optimization of the smelting process in copper extractive metallurgy. Activation energy (Ea) evolutions of the involved processes have been determined by several isoconversional methods; in this sense, the chalcopyrite oxidation processes could be adequately described, among studied models (E1641–16, Ozawa–Flynn–Wall, Kissinger–Akahira–Sunose and Friedman), by the Kissinger–Akahira– Sunose kinetic model. Using this method, Ea and A values are found to be very dependent on the conversion. Under lower conversion levels, higher Ea and A values have been calculated with respect to that found for medium and higher conversion levels.

By Liaqat Ali Shah, Muhammad Farooq, Zait Ullah Shah, Francisco Rolando Valenzuela-Díaz

Bentonite collected from Nowshera (Pakistan) was treated with NaCl, and the < 2-μm clay fractions were separated by sedimentation process. The textural changes in NaCl treated purified bentonite were compared with raw and physically purified sample. It was detected that the NaCl-treated purified bentonite and the sample purified by simple sedimentation, respectively, consist of sodium-montmorillonite and calcium-montmorillonite as a major clay mineral. The honeycombed-type morphology was observed for both the purified samples; however, the particles of NaCl treated purified bentonite were relatively in a compact form. The particle sizes of both the purified samples were found considerably smaller. The high volume percent of the fine particles was noticed in the NaCl-treated purified bentonite. This attributed that the sodium exchange has a valuable impact on the bentonite dispersion in aqueous media during particle size measurement. The relatively high mesopore area/volume and micropore area/volume and specific surface area (SSA) were detected in purified samples. The NaCl-treated purified sample showed relatively high mesopores area/volume than the sample obtained by simple sedimentation. These changes seem to be originated from either high montmorillonite contents and/or the smaller particle size, which might be produced after the layer rearrangement during the interlayer cation replacement by Na+ ions. The large SSA and high porosity of purified samples particularly the NaCl-treated bentonite suggest their potential use as adsorbents, catalysts, pharmaceuticals, and cosmetics.

Jan 7, 2021

By Lixue Wen, Jun Xiao, Dongping Shi, Yan Xue, Jinmiao Wang

Mine ventilation energy consumption is one of the main sources of energy consumption in mining production, accounting for about one-third to one-half of the total energy consumption. Therefore, reducing the energy consumption of the mine ventilation system is crucial for mining production. With the premise of meeting the airflow requirements of the underground work areas and achieving sustainable development of mining production, this paper establishes a nonlinear optimization mathematical model for the mine ventilation network with the objective of minimizing the total power. Regarding the model, optimization of the decision variables was carried out using the method of minimum spanning tree. The constraints for air flow balance, wind pressure balance, and fan operating conditions were optimized using the exterior penalty function method, thereby transforming the model into a nonlinear unconstrained model. Based on this model, a modified sooty tern optimization algorithm (mSTOA) was proposed to achieve optimization. Improved the sooty tern optimization algorithm (STOA) by using the uniform reverse strategy, fitness value-distance balance selection strategy, and mutation strategy. The STOA, mSTOA, and three other classical optimization algorithms were applied to the optimization of a ventilation system of an actual mine. The experimental results show that after using mSTOA to optimize the ventilation network airflow distribution in the mine, the total energy consumption can be reduced by about 35.06% while meeting the constraints and demands of the ventilation network regulation and usage. This is of great value to mine roadway operation environment safety and clean production.

Dec 20, 2023

By Victoria Vaccarezza, Corby Anderson

The demand for rare earth elements for everyday technology and applications has initiated much research into the extraction and recovery of these rare earth elements. An otherwise unknown group of minerals, eudialyte is a zircon silicate consisting of rare earth oxides (REO), contained in a unique mineral structure and represented by a complex chemical formula. Research into extraction and recovery of rare earth elements involves various beneficiation and hydrometallurgical techniques. The goal of beneficiation being to efficiently liberate and upgrade the REO content, followed by hydrometallurgy to extract the desired elements. This overview will discuss previous research on treating eudialyte group minerals via different mineral processing and extraction techniques.

By Wenjun Ju, Xiaodong Sun, Jianwei Zheng, Bingding Yi, Zhaorui Ma, Pengfei Jiang, Lingfu Zhu, Yangfa Zheng

The presence of hard roof poses a significant threat to the safety of underground coal mining. In this study, a mechanical model is established for underground stopes to analyze the overburden structure with the advancing of the mining face. It is indicated that the load-bearing arch structure (LBAS) is formed above the stope for roofs with regular hardness, whereas the reversed-basin bearing structure (RBBS) is formed for hard roofs. Compared with the LBAS, the RBBS can induce an additional pressure at the foot of the bearing structure, and this effect becomes less as the distance between the hard roof and stope increases. The ultra-deep borehole hydro-fracturing technique (UHT) is proposed to weaken the hard roof for pressure release, and the associated equipment and procedures are also presented. The UHT is based on horizontal drilling along the axial direction of the roadway in the roof, and then the receding segmented hydraulic fracturing technique is used to achieve the purpose of fracturing (weakening) of the surrounding rocks. Field tests are carried out in 3022 roadway of Daliangwan coal mine in Yulin to assess the developed technique, equipment, and fracturing procedures. To evaluate the fracturing effect, deep borehole stress-meters are installed at different depths of the fractured and un-fractured zones of the roadway, along with hydraulic support pressure sensors placed at the mining face. The results show that compared with the un-fractured zone, the pressure on the wall and pillar sides is lower than that in the fractured zone, and the associated weighting duration and weighting area ratio of the fractured are reduced by 53.23% and 33.59%, respectively. This indicates that the presented UHT can provide a new solution for the prevention and control of mining disasters induced by hard roof failures in underground coal mining.

Nov 2, 2020

By Fahimeh Dehghani, Louis Ackah, Tathagata Ghosh, Justin Godbold, Jia Liu, Meisam Peiravi, Manoj Mohanty, Azam Baharlouei

Primary economical deposits of rare-earth elements (REEs) are exhausting all over the world, and it has become necessary to find new sources and methods for their extraction. In addition, increasing the application of REEs in modern technological society has increased its demand globally. One of the important movements to compensate for the future shortages of critical metals is the recovery of REEs from recyclable materials. This paper presents a review of the classification and extraction methods, as well as general applications of REEs with emphasis on secondary sources such as coal and coal byproducts, iron ore tailings, apatite, and phosphate byproducts. An overview of the current state of knowledge on the various methods of REE beneficiation and extraction is covered. These methods include physical separation, as well as hydrometallurgical and bio-hydrometallurgical techniques. The application of these REE extraction techniques for enhanced recovery has been driven primarily by the unique industrial application of these important elements. This paper further explores the existing and potential environmental challenges associated with REE extraction. The authors have presented a wide array of literature, in-depth discussion of the subject, and a succinct summary of processes and relevant case studies.

Sep 23, 2020