Search Documents

By M. Zuckerberg, E. Mader, R. Pasyar

We describe a new software product designed for the net present value optimization of multi-open-pit blended ore operations in which it is desired and/or necessary to dump some or all of the waste rock produced in the course of operations back into the voids created in the process of ore extraction. The software product simultaneously decides over the entire life-of-mine which material to mine in which year, once mined what to do with it, and where to put that material which it has decided to waste, all subject to annual blend and capacity constraints.

Jan 1, 2007

By Tim O’Neil

The US Bureau of Mines and the Santa Cruz Joint Venture (SCJV) are working on a production-scale, in situ copper recovery project in Arizona. The research is being conducted at the Santa Cruz site, located 11.2 km (7 miles) west of Casa Grande, AZ (Fig. 1). Santa Cruz is a 1.36-Gt (1.5 billion st) porphyry deposit averaging 0.6% Cu, of which 65% is oxidized, concealed beneath post-mineral alluvium at depths of 365-914 m (1500-3000 ft). The Bureau and the SCJV will evaluate in situ mining as a method for extracting copper from this previously unmined deposit. Research objectives of the Santa Cruz project are: - to demonstrate that an in situ research test can be operated in an environmentally acceptable manner ; and * to operate an in situ well pattern long enough to develop information on copper recovery and economic feasibility data. In situ mining of copper from undisturbed deposits has not been attempted commercially. There are several potential advantages with in situ mining: less exposure of miners to hazards, lower pital costs for the mine and plant and lower operating costs. In addition, there are no pits, dumps or tailings, which means less environmental impact.

Jan 1, 1991

By J. Pinkley

DSI DYWI Rock Dust application is aiding in enhancing safety and productivity in underground coal mining. DSI DYWI Rock Dust combines wet dusting technology and polymers to allow for drying and lift characteristics for rock dusting. DSI DYWI Rock Dust typically dries within 24 to 48 hours depending upon the mine air velocity and humidity. The DSI DYWI Rock Dust Applicator Machine is a completely hydraulic unit. The DSI DYWI Rock Dust Applicator machine allows for batching of product and face spraying operations in permissible locations. The DSI DYWI Rock Dusting Applicator Machine fits in one half of a battery or diesel scoop bucket for ease of transport. It is completely hydraulically powered by the PTO circuit. The DSI DYWI Rock Dust Applicator unit requires a scoop operator, and a person to operate the spray wand, simple operation with two personnel. The first demonstration was at an underground continuous miner room and pillar coal mine which produced a pilot test period opportunity, which proved to be successful, and has now been in full launch mode with the US underground coal mining industry. A typical batch of operation allows for 250? of roof and rib (19? wide by 6? in height) coverage of DSI DYWI Rock Dust application. The DSI DYWI Rock Dust Applicator contains a hydraulic powered air compressor which allows for 30-50% more coverage per batch by improved dispersion of product via air assist spray nozzle. DSI DYWI Rock Dust will add approximately $0.02 to $0.04 per clean ton of coal cost to the mining operation over traditional rock dust cost depending upon mining height.

Jan 1, 2012

By T. C. Page

The Yarnell gold depoSit, located in the Weaver mining district of Yavapai County, Arizona is found within a structurally controlled, hydrothermally altered zone that occurs within a 1700 Ma granodioritic intrusive. Both potassic and sericitically altered rock that occur around and above the low-angle northeast striking Yarnell fault are known to host economic gold mineralization; a wider envelope of weakly-propylitic alterred rock also occurs in this area. During mineralization, strong sericitization accompanied several stages of quartz ± adularia veining, stockwork formation, and localized silicification and potassic replacement, in association with deposition of specularite, pyrite (now oxidized), and gold. The footwall of the fault is also sericitically altered but poorly mineralized. Mineralization along the Yarnell fault continues both northeast and southwest from the main deposit although the thickness of the zone and associated alteration envelope diminish away from the orebody. A sample of undeformed illite taken from the Yarnell fault zone was K/Ar dated at 69 ± 1.6 Ma; this date reflects a minimum age for both mineralization and latest movement on the fault. Gold mineralization is accompanied by modest increases in Ag, As, Cu, and Mo content. Both CO2-and H20-rich fluid inclusions were studied and suggest mesothermal pressures and temperatures of formation for the deposit.

Jan 1, 1992

By J. W. Craven, M. Katom, K. M. McCaffery

At Ok Tedi, ore type and SAG feed size distribution vary widely and frequently. This makes control of the SAG mills by application of the power/pressure relationship difficult. Power logic has traditionally been conservative due to power spikes associated with rapid size distribution changes. A new expert system was installed in early 2000. The system incorporates multiple state fuzzy logic to deal with frequent and radical ore type and size variations, along with monitoring of motor temperatures. A short term power spike no longer warrants immediate radical action. This has resulted in increased mill throughput and improved circuit stability.

Jan 1, 2001

By G. Le Bel

The paper proposes three methods to determine optimum lifetime of a mining project1. The conclusion is that the three methods arrive at the same optimum production rate (by coincidence). It is also stated that: "The stochastic and option pricing models, in addition to providing a more realistic optimum mine life than the traditional NPV (net present value) calculation, showed that the example project has the potential for substantially higher return. By explicitly considering a project's potential risks, the stochastic or option pricing techniques can more accurately describe its probable investment performance." This discussion is intended to demonstrate that: • It is no coincidence that the three methods arrive at the same optimum production rate. • The stochastic and option pricing models do not provide a more realistic optimum mine life than the traditional NPV calculation. • The potential for a substantially higher return is misrepresented. First, a review of investment decision theory in mining is needed. Net present value is the preferred performance measure because of the flexibility offered when comparing various alternatives. However, it presents the following disadvantages: • The discount rate selection is not straightforward. • The NPV obtained represents a deterministic characterization of the variables included in the cash flow calculations, i.e. a single-point estimate.

Jan 1, 1993

By Robert Stefanko

13.1-SUBSIDENCE AND GROUND MOVEMENT ROBERT STEFANKO 13.1.1-SUBSIDENCE AND FAILURE This treatment of subsidence and ground movement will be confined to subsidence control for limiting surface damage by assessing the significant parameters affecting ground movements during mining to optimize mining techniques. The material will be equally applicable to evaporite mining as well as coal but will not deal with block caving or similar systems where failure is deliberately induced and surface protection is not necessary or provided. When an underground opening is established, the original equilibrium is disturbed with resultant stress concentrations. While many factors are involved in opening stability, the span (W) undoubtedly is one of the most important factors in failure. Assuming it is relatively small, the overlying rock strata can bridge across the opening and little if any movement or convergence of top and bottom will occur. However, as the span increases, a point is reached where the stress in the overlying rock strata exceeds some strength value of the rock, and the top breaks. If the opening span is limited to some subcritical value (-We) and/or is at great depth (D), a pseudo-arch will form, achielring stability before rupture occurs to the surface. The boundary of this arch is thought to approximate an ellipse in form with the major axis vertical and equal to four times W, although there has been little field research to substantiate this theory. However, if the width of this opening is increased at this horizon to some critical value (W,) or the same span is created in a shallower seam, the overlying strata ill progressively rupture to the surface and the characteristic subsidence trough is formed (Fig. 13-1) The area of the surface affected is much greater than the area of the seam extracted, depending on the "angle of draw" (a), which is the angle between a vertical line from the edge of the opening and another line extended to a point at which subsidence tails out to zero. This angle has been found to be about 35° in Europe but is rather academic, being a function of instrument precision in detecting subsidence. Since the subsidence effect is so small at any point beyond n 25° angle, this latter may be considered the practical limit of subsidence. Further- more, indications are that the angle of draw varies with depth and nature of the strata.' In a field study over a 1,000-ft-deep potash mine in New Mexico, the maximum angle of draw was found to be 51.5°.2 So far, only a single opening has been considered. However, the width of the excavation applies to any complex mining system of entries, rooms and longwalls as long as the seam has been fully extracted and the width represents the distance from one solid rib to another. It will be noted that the amount of vertical displacement varies from point to point on the surface (s), but the maximum subsidence for a given trough occurs at the center (S). This latter value may not he equal to the maximum possible subsidence (Sm) which occurs only if a critical or super- critical (+W,) width has been exceeded (Fig. 13-1). Substantial surface damage can result when subsidence occurs. Factors affecting the amount and type of ground movement are: thickness and properties of the seam, angle of draw, width of excavation, depth and type of overburden, inclinations of strata and surface, and the amount of support left in the gob. In Europe,

Jan 1, 1973

By Stephen Davies

Mining at Hudson Bay Mining & Smelting's Snow Lake Division is now in the mature stage of the mines' lives. These base metal copper-zinc mines have been operating for more than 30 years. Stopes had small pillars called "crown pillars" left between them. These pillars range up to 100 m (330 ft) long by 40 m (130 ft) wide and 15 m (50 ft) thick. Hudson Bay have been successful in removing these pillars by using cable slings, electric scoops, longhole mining and diesel load-haul-dump equipment. The different shapes and sizes of these pillars has required that many innovative techniques be tried in order to find acceptable economic mining methods. An overview of the different methods will be outlined. Background Hudson Bay Mining & Smelting's Snow Lake Division is located in Manitoba some 800 km (500 miles) north of Winnipeg and 200 km (125 miles) by road from the Hudson Bay smelter complex located in Flin Flon, Manitoba (Fig. I). There are currently three producing underground mines and one open pit operating at the Snow Lake Division, producing copper and zinc concentrates. Pillar recovery is intensive and vital to continued production of these mature mines. The crown pillars are producing more than 50% of the current mine production. This figure will increase in the future. The two mines at which crown pillar recovery is taking place and that will be discussed are the 400 t/d (440 stpd) Rod Mine and the 1000 t/d (1100 stpd) Stall Lake Mine, both five-day-a-week producers. Crown pillar mining has been applied for some time at these mines. However, it was only recently that the crown pillars became vital to production. This has necessitated a number of innovative techniques to recover them.

Jan 1, 1992

By H. Marshall Farrier

In the past few years the world petroleum industry has increasingly felt the weight of changes in the principal economic factors affecting pro¬fits. As a result of, these changes, it has been necessary for many oil companies to acquire certain new facilities in order to strengthen their competitive positions and thereby protect their tremendous investments in crude oil reserves, pipe line facilities, refining operations, and marketing outlets. Principally these needs have been met by new capital outlays. A supplementary, method of acquiring needed facilities, however, has been to obtain existing facilities through complete or partial acquisition of other companies.' properties. It is this method of meeting competitive pressures with which this paper is concerned. This paper presents a statistical breakdown of the mergers and acquisitions which occurred in the oil industry between January 1, 1954, and October 1, 1959, showing the frequency' with which certain types of properties were acquired in each of the years studied. In addition, it discusses the principal economic conditions which stimulated many of these property trans¬fers, comments on the effects of these mergers on the consuming public, and indicates the types of, mergers and the rate at which they may be expected during the next three or four years. The basic data upon which the statistical analysis presented in this paper is based were taken from several published sources. Obviously they are somewhat incomplete because not all mergers and acquisitions were reported However;, a careful search was conducted through, The Wall Street, Journal, The Oil and Gas Journal, Potroleum Week, and The Oil Daily with the result that the data should be reasonably complete and comparable for each of the years studied, It is believed, therefore, that the statistical analysis which' follows provides a reasonably accurate indication of the general trend in mergers and acquisitions during the period studied.

Jan 1, 1960

By R. W. Fedors, S. T. Green, F. T. Dodge, D. B. Walter

Spatial and temporal temperature variations in a high-level radioactive waste repository drift can give rise to moisture transport within the drift. Knowledge of this moisture transport may be important to assessing the potential for corrosion of all metallic components in the drift. The model presented here shows one approach to simulating evaporation, transport, and condensation of water in large underground openings using a framework based on computational fluid dynamics. Simulation results that explicitly model water and latent heat transport are presented.

Jan 1, 2004

By W. Z. Rogers

U.S. feldspar output sold or used in 2005 was an estimated 760 kt (838,000 st), valued at $44 million free-on-board plant. This was below the 2004 volume and was the second year of decline in a row. Output included flotation concentrates, feldspar content in feldspar-silica mixtures, potash feldspar and aplite. The strong housing market in the United States maintained demand for ceramic tiles, plumbing fixtures and fiberglass insulation requiring feldspar. Shipments of glass containers were about the same as in 2004. Imports of ceramic tiles and plumbing fixtures continued to increase, taking the place of U.S.-produced goods and the feldspar required to make them. For 2005, 80 percent of the ceramic tiles sold and 50 percent of the plumbing fixtures sold in the United States were imported. Since 2000, manufacturing plant closures in the plumbing fixtures industry have reduced the demand for feldspar and feldspar-silica mixtures by 100 kt (110,000 st). Increased demand from the ceramic tile industry has partially offset the lost volume.

Jan 1, 2006

By Philip Morey

Large scale surface coal mining will be required to fill future energy demand in the United States. In realization of this long-term commitment to coal resources, the U.S. Energy Re-search and Development Administration sponsored a study to determine the costs and problems of large-scale surface coal mining. As a result of this study a series of computer models were developed that can be used by government and industry to: 1) facilitate mine design and equipment selection, 2) provide detailed analyses of mining and processing costs. Two types of models were developed: detailed simulation models, which provide detailed information on mining systems and equipment to assist in mine design and equipment selection1 and broad models, which provide a first-order evaluation of deposits and new ventures for an entire mining complex. The complete model series permits examination of surface coal mining under a variety of terrain conditions. Six different mining methods were analyzed and documented during the overall project: 1) Area stripping with draglines, 2) Area stripping with draglines, extended bench, 3) Contour stripping with draglines, 4) Area stripping with shovels (loaders) and trucks, 5) Mountain top removal with shovels (loaders) and trucks, 6) Multiple dipping seam mining with shovels (loaders) and trucks. Each major operation in the coal mining pro-cess is represented in these models so that the best methods and equipment may be selected and 50 that the impact of such selection will be reflected in estimates of capital investment, operating costs, and coal price. Individual models allow the user to separately analyze overburden removal, overburden drilling and blasting, coal drilling and blasting, coal loading and hauling, coal preparation and handling, land reclamation, and premining, facilities, and administrative expenses. Because it is impossible to cover all the models in this paper, only the detailed simulation models representative of the technique "area stripping with draglines," are described. The Fort Union Strippable Coal Resource Region, one of eight test cases, is used as an example to describe the models.

Jan 1, 1978

By M. Haase

[ ] How important is a robust communications system for your mine site in order to meet operational and safety requirements? Do you currently have VSAT in place and need a low cost, high quality multi-line VoIP phone system at the site? By adding a single, compact piece of hardware, you can utilize your existing satellite internet connection and have as many as twenty-four separate phones lines from a single unit. The platform is scalable for any size of operation and can be implemented above or below ground.

Jan 1, 2012

By C. F. Barter, H. G. Kreis, D. S. Weber

Before and during in situ mining at the Santa Cruz In Situ Copper Mining Research Project test site, hydraulic testing was conducted at injection and recovery test wells to characterize patterns of fluid movement in the 5-spot well field. Testing included borehole spinner flow meter surveys, single-well and multiple-well injection and recovery tests, straddle packer injection tests, and bromide pulse tracer tests. Results of hydraulic testing for determination of fluid flow regimes were used to modify well and mining zone hydraulics for the purpose of increasing fluid migration in flow pathways of the mining zone with higher copper grade.

Jan 1, 2000

Ceremonies for the induction of four mining industry pioneers into the National Mining Hall of Fame will be held Saturday, Sept.9, 2006 at the Museum Convention Center in Leadville, CO. The four inductees are Earl H. Beistline (1916 to present), R.A.F. Penrose (1863-1931), Robert M. Reininger (1912-2006) and John Stanton (1830-1906). The inductions will bring to 193 the number of mining “greats” whose engraved photographs and biographical sketches are installed in the National Mining Hall of Fame.

Jan 1, 2006

By G. F. Revey

All underground operations have limiting factors that influence overall profitability. Hoisting, hauling, available headings, labor, milling capacity and other factors limit how much material can be removed from an underground mine. Consequently, when mines use limited labor to handle the additional rock from overbreak and to perform extra ground support tasks, productive activity is replaced by non-productive work. Mining economics are further penalized when overbreak causes dilution of ore grades. This paper reviews organizational systems that mines have used to create environments which foster the creation of successful overbreak control programs. Actual case histories document the various quality improvement techniques, worker incentives, and practical project management systems used by these mines. A brief review of controlled blasting technology sources and overbreak measurement tools is also included.

Jan 1, 1997

By Robert M. Matyas, P. E. Sperry, Robert J. Smith, A. A. Mathews

INTRODUCTION The first Dispute Review Board (DRB) was utilized on a tunnel project 20 years ago. Increasingly utilized on a wide range of construction projects, DRB's are becoming the norm on tunnel and underground projects. This paper summarizes the growth in this usage, uses observations and experience to establish that barriers to the utilization of DRB's are more perceived than real and that many arguments against the DRB concept are not valid, and notes some of the salient elements that should be considered in practice to optimize DRB effectiveness. The purpose of the paper is to provide an annotated checklist for current and prospective users. The basic concept, structure, and operation of DRB's are described elsewhere and will not be repeated here (ASCE, 1991). DISPUTE REVIEW BOARD USAGE A compilation of Dispute Review Board usage for tunnel and underground projects to January 1994 indicated use on 63 contracts with a cumulative construction value of $3.8 billion and a total of 60 disputes settled. As of that same date, DRB's were planned for another 63 contracts with an estimated construction value of $4.7 billion. (A listing of these 126 projects is available from the authors.) This success and popularity have spread to other civil projects as well as process and building construction. The increase in DRB usage has been exponential. See Figure 1.

Jan 1, 1995

The Colorado portion of the Rio Grande rift is clearly defined physiographically from the south in the San Luis valley northward to the latitude of Leadville where sediments of the Dry Union Formation (Tweto, 1961) accumulated within the subsiding rift zone. To the north of Leadville is a system of faults active in the late Tertiary, including the Mosquito fault that offset a portion of the Climax mineralization (Wallace et al., 1968). Tweto (197B) describes remnants of Dry Union Formation against the Mosquito fault north of Dillon in the Blue River valley, so it is apparent that the rift and associated sediments extended well to the north of Leadville. Kelley (1952, 1954, 1956) and Chapin (1971) have noted in New Mexico that the Rio Grande rift is a series of en echelon basins, offset to the east, with constrictions connecting them (Fig. 1). In Colorado the structural basins are offset to the west. The net effect of all the rift zone basins in New Mexico and Colorado is an arcuate pattern (Fig. 1) abutting the Colorado Plateau and Sari Juan Volcanic Province on the west. The width of the rift system gradually decreases northward to about Leadville where rift definition is not apparent.

Jan 1, 1987

By Rahul Singh, Sunil Kumar, Erich Dohm, Maoming Fan

The rapid increase of P2O5 use for food, biofuels, and LiFePO4 batteries etc. accelerates the depletion rate of phosphate reserves. In the phosphate industry, a significant amount of ultrafine phosphate has been discarded as slime tailing due to processing difficulties. The major problems associated with ultrafine particle flotation are low probability of bubble-particle collision and adhesion, and high probability of unwanted gangue particles entrainment. This paper investigates the enhanced ultrafine phosphate particle flotation probability by Eriez’ CavTube generated fine/ ultrafine bubbles and the improved flotation selectivity by wash water etc. Ultrafine phosphates with various gangue minerals of quartz/muscovite, calcite/dolomite, and iron/ silica were studied. Microscopic observations show that the entrained ultrafine gangue minerals can be minimized by using wash water in column flotation. A three-factor threelevel central composite experimental design was conducted for ultrafine phosphate flotation. For comparison, both benchtop mechanical cell and laboratory column flotation tests were performed at their optimal respective flotation conditions. Using Eriez CavTube column flotation technology for Industries Chimiques du Senegal (ICS) ultrafine slime tailings, a concentrate grade of 36.0% P2O5, was achieved at 89.4% P2O5 recovery. Improved flotation performance was achieved using column flotation as compared to benchtop mechanical cell flotation. The benefits of Eriez’ column flotation technology realized from this study include the high P2O5 grade and recovery.

Feb 1, 2024

By C. F. de Mendonca, T. Kater, R. P. de Souza

The authors are to be commended for finding a material for pellets binding that we were unable to uncover during the investigations that led to US Patent No. 3,748,116, “Method for producing metallic iron powder from iron ore concentrate, ” July 24, 1973, by G.G. Reed, Jr., J.M. Karpinski, and S.V. Fox. This patent concerns a method of processing “super’ ‘-concentrates prepared from magnetite or “blue dust” into molding-grade metallic iron powder for use as a bulk commodity, in contrast to current methods which produce small batches that are custom-blended with additives and/or alloye to customer specifications. The one thing we had not found at that time was an organic binder (mineral-matter-free ) that would allow induration to produce hardened pellets that would survive SL/RN Direct Reduction. Peridur appears to provide this missing link needed for large scale (200 t/a, or 220,460 stpy) single line plant capacity consistent with a low market price to ensure greatly broadened use of metallic iron powder. I hope that industry will adopt this combination so that metallic iron powder usage can fulfill its potential

Jan 9, 1985