Search Documents

By R. L. Virta

Four companies mined ball clay in four states during 2005. They included H.C. Spinks Clay (owned by Franklin Minerals), Kentucky-Tennessee Clay (owned by Imerys), Old Hickory Clay and Unimin. Production was estimated to be 1.32 Mt (1.45 million st) valued at $53.3 million, based on the results of a preliminary survey of the ball clay industry. Production in 2004 was 1.22 Mt (1.34 million st) valued at $54.1 million. Tennessee was the leading ball clay producer state with 61 percent of domestic production, followed by Texas, Mississippi and Kentucky.

Jan 1, 2006

By Ian Farmer, Nigel Glossop, Philip Garritty

Performance of tunnel boring machines - usually expressed in terms of penetration per revolution - is determined by relations between machine thrust and torque, head diameter and rock strength. It can be shown that for a given machine power and head diameter there is only one rock strength at which the machine performs optimally. In weaker rocks the available torque limits performance and in stronger rocks, the available thrust. Performance data shows that, historically, machines have been designed to cut weaker rocks. Optimization of thrust is required to improve performance in stronger rocks.

Jan 1, 1987

The inquiry into the explosion at the Moura No. 2 Mine in August 1994 recommended -?Emergency procedures should be exercised at each mine on a systematic basis, the minimum requirement being on an annual basis for each mine.? (Windridge et al. 1996). In December 1996 the ?Approved Standard for the Conduct of Emergency Procedures Exercises? was published and has been subsequently revised (Queensland Department of Mines and Energy Safety and Health Division 1999). This document provided guidelines for conducting mine site emergency exercises as well as the requirement for a test of state-wide emergency response by holding a Level 1 Mine Emergency Exercise at one mine on an annual basis. From 1998 to date (January 2008) ten Level 1 Mine Emergency Exercises have been held in Queensland, Australia. This paper discusses each of the exercises conducted to date as well as the logistics, scenario preparation, planning and organising required to conduct emergency exercises at this level.

Jan 1, 2009

By Franz Walchshofer, Mark Kuchta, Nobuharu Isago, Ugur Ozbay, Wolfgang Dolsak

A series of in situ pull test were performed on a new design friction stabilizer bolt with the objective of determining its performance characteristics. The bolt is installed while drilling, thus improving safety and significantly reducing the installation time. An optional expansion element can be inserted into the bolt to provide an end-anchorage, which further increases the bolt’s capacity. In situ tests show that the pull capacity of the 2 m long new design bolt is about 15 tons. When installed with an expansion element, the pull capacity of these bolts becomes as high as 30 tons.

Jan 1, 2005

By Peter Klaver

Deep tunnels have been used for decades for the temporary storage of large volumes of urban runoff, both storm water and combined sewer overflow (CSO). Tunnels are attractive because they reduce surface disruption and do double duty as storage and conveyance systems, collecting overflows from multiple locations and transporting them for treatment to various facilities. Like any hydraulic system, however, there are dynamic effects that must be fully understood during the design phase so that the final constructed product does not have unintended negative consequences. Preliminary sizing of storage tunnels is typically based on the total volume required. For example, if studies have determined that a volume of 56.8 ML (15 million gal) will provide the intended level of control, then that figure can be used, along with a preliminary idea of the desired tunnel length, to compute the required diameter. Of course, filling a long tube with water from various points along the way is not at all the same as pouring water into a bucket, and these dynamic effects require additional attention from design engineers. The rapid filling of storage tunnels can lead to the formation of bores, which are essentially moving walls of water. An open channel bore can build in height until it reaches the crown of the tunnel, at which point it becomes a pipe-filling bore. Figure 1 depicts both kinds of bores moving upwards in a rapidly filling tunnel. Bores can strike the ends of tun-nels with tremendous force, driving water and entrained air upwards into dropshafts and creating strong pressure surges in portions of the tunnel that are already filled. If the hydraulic surges are high enough to reach grade, they can cause overflows and/or damage structures at the surface. Trapped air pockets can occur through several phenomena, including the reflection of bores off dropshaft structures and the occurrence of ?premature pressurization.? The latter refers to the situation where the inflow to a tunnel is increasing more rapidly than the tunnel can convey it, such that the pipe becomes surcharged at an upstream point while points downstream are still flowing as an open channel. These air pockets are a great nuisance as they migrate toward points in the tunnel where they can rise to the surface, which are often shafts that are already filled with water (Fig. 2). The ?geyersing? that results can be hazardous and costly.

Jan 3, 2010

By Samuel J. Gambino

Preliminary recommendations for the Upper Northwest Interceptor 1&2 specified installation of reinforced concrete pipe using pipe-jacking methods. However, a larger one-pass tunnel constructed using precast segmental lining would provide additional storage volume. The risk of encountering unexpected conditions or events and the resulting cost impacts could differ significantly for these two options. A probabilistic life-cycle cost analysis of these alternatives was performed. This paper discusses the construction alternatives considered, the risk assessment methodology used to evaluate these alternatives, the input parameters and risk factors used in this analysis, and the recommended project which is currently being constructed.

Jan 1, 2008

By Rafael C. Castro

As part of its risk management plan, the South Central Connecticut Regional Water Authority (RWA) is assessing the condition of its system of raw water conveyance tunnels and connecting pipelines. In 2006, the RWA inspected one of the system?s main tunnels, a 4-mi, 1950s-era tunnel that had not been inspected since its construction. The inspection team prepared extensively for the unknown conditions in the tunnel, and the inspection was completed safely and successfully. This paper describes the team?s pre-entry preparations, dewatering and ventilation efforts, surface-to-tunnel communication, access, physical inspection of the tunnel, and the lessons learned throughout the process. Additionally, this paper will preview planning for the subsequent inspections.

Jan 1, 2008

By R. C. Freas

Composite materials are finding new applications daily, ranging from automotive parts to synthetic lumber. The variety of applications seems almost limitless. However, these emerging products bring both new opportunities and new challenges to the field of industrial minerals. One of the primary challenges is from alternative materials other than industrial minerals. Thus the question is asked whether industrial minerals will truly benefit from the growth in market applications for composite plastics. This article highlights some of the opportunities for industrial minerals while focusing on performance and competitive demands on mineral products intended for use in this developing market.

Jan 1, 2000

By F. B. Henderson

1.0 PROLOG Since the "end" of the Cold War, revolutionary new research and commercial remote sensing capabilities are being developed that will dramatically change the way we map the earth and address its environmental problems. The technology challenge is not the growth of new environmental remote sensing technologies themselves. It is, rather, how these new innovative observing systems can be accepted and used to the benefit of both the regulatory and the mining communities in the light of present concerns about unknown risks of discovery and liability. The basis for this paper is an unpublished technology primer prepared for the industry-government Workshop on Advanced Measurement and Site Characterization for Mining Impacts held at Colorado School of Mines, Golden, Colorado, July 14-17, 1997

Jan 1, 1999

By K. R. Griffin

Explosions in underground coal mines have been a serious safety concern since the advent of mining; despite significant technological advances, they are still occurring. Parameters such as barometric pressure, geological changes, and changes in ventilation can contribute to an explosion. These factors can be monitored with available and developing technologies to create algorithms that predict when explosions are more likely to occur. This paper reviews current underground atmospheric monitoring systems and related regulations around the world. In addition, suggestions for improvement and implications for explosion prevention are discussed.

Jan 1, 2011

By Howard J. Handewith

Long used in mine development in England, Europe and Russia, roadheaders are growing in size, features, productivity and application. Beginning with the basics, this paper covers the economic and the technical aspects of the new roadheaders in both mine production and development. The author explains how to choose and integrate roadheaders into ongoing operations as another step in the inexorable march from labor to capital intensive mining. Innovations now on the drawing boards are covered that are the challenge of the future.

Jan 1, 1983

By Daniel H. Isreal

Because the federal government owns and controls nearly 80% of the most valuable oil shale reserves in the West, it is inevitable that federal leasing and siting will play a prominent role in development of an oil shale industry during the 1980s. Also, because of recent enactment of the Synthetic Fuels Corp. authorizing up to $88 billion in loan and price guarantees-federal financing will provide the critical incentive to permit private investment in a still infant industry.

Jan 1, 1981

By Ed Cope

The newly discovered South Arturo deposit is a Carlin-type, breccia-hosted, oxide gold deposit located on the Dee Mine property at the north end of the Carlin Trend in Nevada. The Dee Gold Mine was discovered in 1981 by Dee Delamar, a Cordex geologist. The property was put into production by Rayrock Mines in 1984. During its 16-year mine life, the Dee Mine produced about 18.6 t (600,000 oz) of gold from oxide ore at an average production rate of about 1.24 to 1.55 t/a (40,000 to 50,000 oz/year). In October 1997, Bar-rick Gold Exploration acquired the right to earn a 60-percent interest in the Dee property from Dee Gold Mines through an exploration farm-out agreement. Barrick Gold Exploration began exploration activities on the property in 1998 and vested in its 60 percent operating interest in 2004. However, the discovery hole at South Arturo was not drilled until July 2005 from atop the historic mine dumps located 300 m (985 ft) south of the Dee openpit. The discovery hole (BD-72) encountered a cumulative 75.6 m (248 ft) of oxide mineralization grading 1.9 g/t (0.055 oz/st) gold beneath 260 m (855 ft) of dump material and post mineral Tertiary Carlin Formation volcanic and sedimentary rocks. Oxidation within the deposit extends to depths greater than 610 m (2,000 ft). The deposit has passed the prefeasibility test and is presently in the feasibility stage. Exploration is on-going to enhance or enlarge the known deposit. The current resource for the deposit stands at 40.4 t (1.3 million oz) of gold. The South Arturo discovery is an example of an historic mining property yielding a new discovery through the diligent application of area selection criteria of the model type and persevering when early results were generally negative. Barrick?s original exploration pro-grams on the property were focused on the discovery of deep, high-grade sulfide deposits that would likely be mined by underground methods. As it turns out, South Arturo is mostly oxidized and will be amenable to mining by openpit methods

Jan 1, 2008

By Jan L. Reichelderfer, Thomas L. Richardson

Completion of the H-3 Highway Tunnel Project was a critical element in opening this award winning project. The exploratory tunnel was completed as a maintenance tunnel and included difficult shafts extending into the main tunnel cross passages. The project also involved a major addition to the traffic operations center including a deep excavation in close proximity to the tunnel portal structures. The projects also included various completions and improvements to the main tunnels, such as paving, drainage, maintenance, and a variety of critical life-safety issues, such as radio systems, telephones, etc. The highway opened in December 1997.

Jan 1, 2001

By D. R. Wilburn

This summary of international mineral exploration activities for the year 2005 draws upon available information from literature, industry and U.S. Geological Survey (USGS) specialists. It provides data on exploration budgets by global region and mineral commodity and identifies significant mineral discoveries and exploration target areas. It also discusses government programs affecting the mineral exploration industry and presents analysis of the mineral industry based on these data. Two types of information are reported and analyzed in this annual review of international exploration for the year 2005. They include budgetary statistics provided by Metals Economics Group (MEG) and information on regional and site-specific exploration activities in 2005 compiled by the USGS.

Jan 1, 2006

By Nikolas K. Sokol

Underground construction often requires working within a very congested urban environment, including excavating shafts adjacent to highly sensitive and multistoried structures, sometimes even within such structures. Shafts adjacent to heavily loaded column footings are often required due to space constraints. Invariably, footing surcharges must be considered during the design of shaft rock reinforcement. Rockwedge stability evaluation reveals that column surcharges can greatly impact the ability to meet the desired factor of safety. Design methodologies and examples to deal with these special circumstances are presented.

Jan 1, 2008

By M. S. Riyazulla

A model of a new laboratory magnetic separator has been conceived to cater the needs of process engineers and mineralogists world over engaged in mineral characterization and beneficiation. It would be essentially a laboratory instrument for the separation and concentration of various ferro and non-magnetic minerals. Based on the basic concept of Frantz Isodynamic Magnetic Separator, the new separator conceived would not only speed up the work of a process mineralogist and save the energy, but it would effectively separate and sequentially produce about fourteen fractions at a time. In the present paper, the probable operational procedures and the design have been discussed in detail for the various mining companies to assess its economic feasibility. If it could be fabricated, it would have a worldwide market The concept has been patented in author?s name in India.

Jan 1, 2009

By J. Barrett

State-of-the-art wireless communication and location-tracking technologies will dramatically change the face of mine worker safety. The MineTracer System developed by a Liberty Lake Washington company is a broad capability wireless sensor network based on a new breed of technologies known as wireless mesh systems. In this paper, R&D Manager Jim Barrett summarizes the balance of engineering tradeoffs that result in a system that (1) performs well, (2) is survivable against many types of mine accidents, (3) operates for many hours post-accident on battery power, (4) meets stringent MSHA requirements for intrinsic safety, and (5) is economically affordable for the mines.

Jan 1, 2009

By R. Dillinger

In the environmentally conscious social atmosphere today, reclamation in surface mines has become a main issue to the public and the regulatory committees. In response to this increased attention, many regulatory committees have begun to enact more stringent regulations on surface mining operations. Operations across all spectrums of the industry have seen changes. Recently and most visibly the mountain top removal mines have seen several new regulations focusing on environmental protection. Specifically regulatory committees have emphasized a focus on the methods of reclamation and recovery of layers suitable for vegetation. These layers are the most visible once the operation has concluded. Also, these layers have the most human interaction (farming, hunting, and house development). Often times the new regulations enacted are shifting from a performance base to a standards base. The key differentiator being a performance base dictates the final result while a standards base dictates the method to achieve the result. The very nature of many regulations (especially those that are standards based) not only challenges the physical limitations of the equipment used today, they come with a financial impact. For the purpose of this paper, the model will be a surface coal operation, utilizing draglines as primary overburden movers. The coal seam is ten feet thick, the overburden ninety five feet thick, the pits are 150 feet wide, and the dragline is a Bucyrus Erie 1570.

Jan 1, 2011

By David Van Horsen

Big Creek Tunnel 2, constructed in 1912, is located in the Sierra Nevada Mountains of California, east of Fresno. It is horseshoe and circular shaped with a 3.6m (12ft) diameter and extends 6.6km (4.1mi). Historically, tunnel performance suffers from highly jointed rock and low cover. In 2003, leaks were observed surfacing through outcrops of highly jointed graniodiorite, and subsequently investigated by visual inspection, joint mapping, ground penetrating radar, and a water-tracing survey. Several grouting targets were identified as a result of these investigations. Cement grouting was used to fill void spaces, broken rock and open joints expected to exist behind the concrete and steel liners. Project work consisted of grout hole drilling through the existing concrete liners, and grout placement through squeeze packers supplied by standard grout hose and portable grout plants. Grout pressures were typically 20?30 psi. Grouting was completed in 16 days with a total of 1,550 sacks of Type II/III grout placed at the three likely leak source areas. No grout was observed exiting the tunnel and the leak was stopped.

Jan 1, 2008