Search Documents

By C. Erichsen

ABSTRACT: The Berg Bock Freeway Tunnel represents the southernmost link of the "Thuringian tunnel chain" of the new freeway A71 located in the eastern part of Germany. It comprises two tubes each 2700 m in length. From north to south, it passes through the Suhl granite, the base sediments and the porphyrite of the New Red as well as the layers of the Middle Bunter. The two tunnel tubes were driven by the shotcrete method within appr. 10 months. With four tunnel faces, maximum performances totalling appr. 30 m/d were attained. Additional, supplementary demands on the safety conception, resulting from the findings from and the analysis of fire accidents in tunnels in recent years, had to be fulfilled in the execution planning at short notice. The inner lining is largely constructed using non-reinforced concrete. Reinforcement is only installed in the portal zones, in tunnel sections in less stable rock and in areas with a special cross-section as for instance cross connections and niches. ZUSAMMENFASSUNG: Der Autobahntunnel Berg Bock stellt das südlichste Glied der "Thüringer Tunnelkette" auf der Autobahn A71 dar, die im Osten von Deutschland liegt. Er besteht aus zwei Röhren von je 2700 m Länge. Vom Norden nach Süden durchörtert er den Suhler Granit, die Basissedimente und den Porphyrit des Rotliegenden, sowie die Schichten des Mittleren Buntsandsteins. Die beiden Tunnelröhren wurden in Spritzbetonbauweise in einer Bauzeit von etwa zehn Monaten aufgefahren. An vier Vortriebsorten wurden Spitzenleistungen von insgesamt etwa 30 m/d erzielt. Ergänzende Anforderungen an das Sicherheitskonzept, die sich auf der Grundlage der Auswertung der in den letzten Jahren aufgetretenen Brandunfälle in Tunneln ergeben haben, wurden im Rahmen der Ausführungsplanung kurzfristig berücksichtigt. Die Tunnelinnenschale wurde weitgehend aus nicht bewehrtem Beton hergestellt. Nur in den Portalzonen, in Tunnelabschnitten mit weniger standsicherem Fels und in Bereichen mit speziellen Querschnitten, wie beispielsweise im Bereich von Querstollen und Nischen, wurde bewehrter Beton ausgeführt. RÉSUMÉ: Le tunnel d'autoroute de Berg Bock représente le plus méridional maillon de la "chaîne thuringienne de tunnels" sur l'autoroute A71 dans l'est de l'Allemagne. Il se compose de deux tubes d'une longueur de 2700 m chacun. Du nord vers le sud, il traverse le granit de Suhl, les sédiments de base et le porphyrite du Rotliegendes, aussi que les strates du grès bigarré intermédiaire. Les deux tubes étaient creusés en méthode de construction de béton projeté dans une période de construction d'environ dix mois. À quatre fronts de taille rendements maximaux collectifs d'environ 30 m par jour étaient obtenus. On a eu égard à court terme dans la conception d'exécution à des demandes supplémentaires vers la conception de sécurité, qui ont résulté sur la base de l'interprétation des accidents d'incendie dans des tunnels dans les années dernières. La paroi intérieure était construite largement de béton non armé.

Jan 1, 2003

By M. Gericke

The microbial leaching of metal sulfides is now an established biotechnological technology. Over the past 25 years, refinements in the engineering design of bioleaching processes have paralleled advances in our understanding of the diversity and role of the micro-organisms driving the process and the mechanisms by which micro-organisms enhance metal sulfide oxidation. Commercial success started with the treatment of refractory gold concentrates using mesophilic micro-organisms, followed by the development of tank bioleaching processes for the treatment of base metal concentrates. This was, initially, a mesophilic process with limited potential for recovery of copper from chalcopyrite concentrates due to slow rates and low copper extractions. The exploitation of thermophiles represents a major breakthrough in the development of bioleaching technology for the treatment of chalcopyrite-containing ores and concentrates. This development also opened the route to heap bioleaching of chalcopyrite ores, which is now a major focus of research programmes and piloting campaigns. This paper reviews the historical development of minerals bioleaching processes and gives an update on the current status of commercial tank and heap bioleach operations around the world.

Jan 1, 2009

By L. Thomson

"The smelter at Sudbury Integrated Nickel Operations, located in Sudbury, Ontario, operates a single electric AC furnace. This furnace treats nickel sulphide concentrates produced by Glencore and third-party feeds and as such its performance is key to the company’s nickel supply chain. Currently the plant has two shutdowns per year in order to carry out significant repairs on matte tap-holes.Improved monitoring systems that enable better prediction of tap-hole wear have been a continued focus. The electric furnace is an essential piece of the smelter flow sheet requiring the need for planned tap-hole maintenance along with robust systems for management according to to this plan.The ability to meet our goal of zero harm is ensuring that safe practices are in place. Detailed procedures and cool-down practices have been implemented to ensure that required matte chemistry and temperature criteria can be met during the period leading into a shutdown for tapblock maintenance.A significant repair of the electric furnace will take place in 2015. During this rebuild, the sidewalls and matte endwall will be replaced. There is work underway to improve wall and matte end performance in an attempt to extend the time between rebuilds. This paper will review the approach taken towards this end."

Jan 1, 2014

By D. A. Viljoen

The ore mined at Black Mountain is of a complex nature, being composed of both magnetic and massive sulphides, which have greatly varying metal values. Because of this, there is need for a rapid method of assaying for the continuous monitoring and control of the process streams, and the Outokompu Courier onstream analysis system and the Proscon process-control computer systems have therefore been installed. Geostatistics In view of the continuing demand, the Department of Mining and Mineral Sciences in association with Special Courses Division, Department of Adult Education and Extramural Studies, both of the University of Leeds, will offer two further courses on A Practical Introduction to Geostatistics in 1981, each covering ten working days. The courses will run from 30th March to 10th April and 14th to 25th September.

Jan 1, 1980

By T. Oberthür

The Great Dyke of Zimbabwe constitutes the world?s second largest reserve of platinum group elements (PGE) after the Bushveld Complex in neighbouring South Africa. Within the Great Dyke, economic concentrations of PGE are restricted to sulphide disseminations of the Main Sulphide Zone (MSZ), which are currently mined at the Ngezi, Unki, and Mimosa mines. Near-surface oxidized MSZ ores have a large potential. Their total resources are in the range of ca. 160 ? 250 Mt; however, all previous attempts to extract the PGE from this ore type proved uneconomic due to low PGE recoveries (<< 50 per cent) achieved by conventional metallurgical methods. Within the ores of pristine, sulphide-bearing MSZ, the PGE are bimodally distributed. Platinum occurs mainly in the form of discrete platinum group mineral (PGM) grains (mainly bismuthotellurides, sulphides, and arsenides), whereas approximately 80 per cent of the Pd (and some Rh) is hosted in pentlandite. Within the oxidized MSZ ores, the PGE are polymodally distributed. Whereas arsenide- and sulphide-PGMs, making up ca. 25 per cent of the original Pt content of the ore, largely remain stable (relict PGMs), the remaining PGMs are disintegrated. The base metal sulphides are destroyed, partly releasing their base metal and PGE contents, and are replaced by iron oxides or hydroxides. Unspecified amounts of the PGE are redistributed and either form secondary PGMs, are found in chemically and mineralogically ill-defined (Pt/Pd)-oxides or hydroxides, or in iron-hydroxides, Mn?Co-hydroxides, and in secondary silicates. The problematic processing of oxidized MSZ ores is attributable to their complex nature and polymodal distribution of the PGE, prohibiting a significant upgrading of the ores by conventional metallurgical methods. Therefore, only bulk leaching methods are viable for ore treatment, and novel metallurgical methods have to be developed for the processing of these ores. Our ongoing work aims at locating the PGE in their mineralogical form in order to understand the mineralogical balance of the PGE in the ores and thereby facilitate the evaluation of metallurgical options for their recovery. A short overview on options and recent advances regarding the recovery of the PGE from oxidized ores is given.

Jan 1, 2012

High pressure grinding roll (HPGR) technology is used in an increasingly diverse range of applications, predominantly iron ore, gold and diamonds. KHD Humboldt Wedag HPGRs are applied world-wide, and consistently prove to be well designed and reliable operating units, with their performance meeting the pre-set standards. This publication summarizes some of the features and experiences for recent applications in treatment of copper ore, coarse iron ore, and gold ore. Summary data of roll surface wear life and operating data are given, together with operational observations. In addition, effects of feed segregation and truncated feed are discussed, as well as the implications of a product recycle flow sheet.

Jan 1, 2012

High pressure grinding roll (HPGR) technology is used in an increasingly diverse range of applications, predominantly iron ore , gold and diamonds. KHD Humboldt Wedag HPGRs are applied world-wide, and consistently prove to be well designed and reliable operating units, with their performance meeting the pre-set standards. This publication summarizes some of the features and experiences for recent applications in treatment of copper ore, coarse iron ore, and gold ore. Summary data of roll surface wear life and operating data are given, together with operational observations. In addition, effects of feed segregation and truncated feed are discussed, as well as the implications of a product recycle flow sheet.

Jan 1, 2012

By P. Altounyan, K. Akermann, T. Van den Berg

Amandelbult Mine is currently undertaking a trial to mechanise the mining of the UG2 reef through the introduction of room and pillar mining. As part of the trial, a system of managing the control of the hanging wall has been introduced, based on systems and technology that are proving successful in the nearby coal mining industry. The principal features are the use of a high bond strength, stiff bolting system which can be easily installed to a high standard, and a range of in situ tests and measurements to optimise the level of support installed to control the movement of the hanging wall. The rock bolt system and the measurements and tests described are new to the platinum mining industry. The paper describes these systems and their adaptation and application to hard rock mining. La Mine d’Amandelbult est actuellement dans des essais en vue de mécaniser l’extraction dans la veine UG2 grâce à l’introduction d’une exploitation par chambres et piliers. Dans le cadre de ces essais, un système de gestion de la paroi suspendue a été introduit, base sur des systèmes et une technologie qui prouvent donner de bons résultats dans l’industrie voisine d’extraction de la houille. Les caractéristiques principales sont l’utilisation d’un système de verrouillage raide et à forte adhérence qui peut être installé à un haut niveau de qualité et une gamme d’essais et de mesures in situ pour optimiser le niveau de soutien installé pour contrôler le mouvement de la paroi suspendue. Le système de verrouillage de la roche ainsi que les mesures et les essais décrits sont une nouveauté dans l’industrie minière du platine. La communication décrit ces systèmes ainsi que leur adaptation et leur application à l’exploitation minière en roche dure. Amandelbult Mine unternimmt gegenwärtig einen Test um den Abbau des UG2 Riffs durchEinführung des Kammerpfeilbau zu mechanisieren. Als Teil dieses Tests wurde ein System zur Kontrolle der Stollenfirstes eingeführt, welches auf jenen Systemen und Technologien basiert, diesich im nahe gelegenen Kohlebergbau als erfolgreich erwiesen. Die prinzipiellen Charakteristikasind der Gebrauch von einem steifen Bolzensytem mit hohem Verbundwiderstand die leicht zueinem hohen Standard gebracht werden können, und eine Reihe von in-situ Tests und Messungenum das Niveau der installierten Unterstützung zu optimieren, und um die Bewegung desStollenfirstes zu kontrollieren. Das Gesteinsbolzensystem, die Messungen und die Tests, diebeschrieben werden, sind neu in der Platinbergbauindustrie. Diese Arbeit beschreibt diese Systeme, deren Anpassung und Anwendung im Hartgesteinsbergbau.

Jan 1, 2003

By Axel Schulze

HUGO PETERSEN has developed from the traditional firm of the same name that was established in 1906 in Berlin and is an engineering company specialising in general plant engineering now based in Wiesbaden. HUGO PETERSEN has many years wide-ranging experience in process plant engineering, primarily in the field of Sulphuric Acid Processes and Gas Cleaning. Together with its main shareholder, Chemieanlagenbau Chemnitz GmbH (CAC), a company with over 40 years experience in the international plant engineering business, HUGO PETERSEN implements turnkey new plants from initial consultancy right through to commissioning. In addition, HUGO PETERSEN can offer its clients improvements and revamps of existing plant systems. Initial consulting, planning and implementation take place within the context of a lean company organisation with experienced engineers and specialists. In all respects, many years of experience guarantee expertise over a wide range of possible applications For clients from the chemicals and metallurgical industries, as well as those in metals processing, HUGO PETERSEN GmbH?s breadth of experience means not just an efficient introduction to new methods and processes, but also their full implementation. In addition, along with design and construction for individual components, the company?s range of services also covers supply of complete plants, as well as modernisation projects and revamps in line with local conditions and existing quality requirements With own technologies and patents in the field of gas cleaning and sulphuric acid, supplemented by licences and cooperation projects, HUGO PETERSEN ensures expertise over a wide range of applications. With specialists and expert knowledge in these fields of application, HUGO PETERSEN is your partner of choice, supporting you and bringing your acid, and project to a successful conclusion.

Jan 1, 2009

By S. V. Rungan

The modern mining industry is increasingly being tasked to comply with various legal, industry and social prerequisites. In addition to complying with these, the mining industry is further expected to effectively report on their compliance. Although there are many models that aid the mining industry in compliance and reporting, it is perhaps opportune for a new model to be introduced. The Compliance Spindle is postulated as a new and alternative model which is easy to understand and has the possibility of implementation in South Africa and other jurisdictions as well. The Compliance Spindle is also an effective tool to educate future compliance officers. The new model provides for all aspects of compliance and reporting and can be easily modified to take account of new developments in the mining compliance and reporting arena.

Jan 1, 2010

By C. Musingwini, A. S. Nhleko, M. J. Mahase

"In an environment like the mining industry, which is characterized by different stakeholders with multiple objectives, multi-criteria decision analysis (MCDA) is a useful approach for optimal decision-making. The application of MCDA techniques in the mining industry has predominantly been in mine planning and related problems, although no comprehensive survey has previously been undertaken to establish the application trends. A survey of the use of MCDA techniques was therefore conducted using case studies from the literature. It was noted that often two or more methods are applied to the same problem in order to increase confidence in the solution derived. As the number of criteria and alternatives increases, some methods become inefficient. A combination of the analytic hierarchy process (AHP) method with other MCDA techniques was the most frequently used approach, indicating the efficiency of the AHP method, especially when evaluating problems with more criteria and fewer alternatives. A combination of fuzzy theory with AHP or other methods incorporates uncertainty. The findings from the survey will benefit users applying MCDA techniques to solve mine planning and related problems.IntroductionA country’s natural resources serve the needs of different groups of people within the country. These different groups are collectively known as stakeholders (Herath and Prato, 2006). Stakeholders have different needs, preferences, and expectations, which describe and define the criteria to be considered in decision-making. The options available as solutions describe the alternatives in decisionmaking theory. The criteria and alternatives have to be evaluated simultaneously when making decisions, and this is when multicriteria decision analysis (MCDA) techniques become invaluable (Herath and Prato, 2006) because the human mind is considered to be limited when solving complex and intangible problems with several criteria and alternatives (Saaty, 2007). MCDA techniques belong to a broad group of techniques called multi-criteria decision-making (MCDM) techniques. The other group of techniques within MCDM comprises the multi-objective decision-making (MODM) techniques. MODM techniques are generally used to solve problems with an infinite number of alternatives, while MCDA techniques are generally used to solve problems with a finite number of alternatives (Musingwini, 2010)."

Jan 1, 2016

By C. C. Birch

Due to grade estimation uncertainty, two statistical errors can occur. The Type I error is where material is classified as ore and mined, despite the true value being below the break-even grade. This material is dilution. The Type II error is where the material is estimated to be below the cut-off grade and is classified as waste, although the true grade is actually above the break-even grade. This material is not mined and is lost. The uncertainty was assumed to follow a normal distribution in a previous study. For this study, estimated block values are compared to those determined after mining (the best estimate of the true grade). This actual data from four mines shows that the uncertainty follows a Laplace. There is no single solution regarding adjusting the cut-off grade away from the break-even grade, considering estimation uncertainty, that could be applied to all gold mines. However, adjusting the cut-off grade downwards (up to 22% for one mine) is noted when optimizing the profit considering grade uncertainties. This type of adjustment could open up significant mining areas and extend the life of the mine.

Jul 2, 2022

By P. Stefanek, N. Duda, B. Jachni, P. Stefaniak, B. Bursa

The Zelazny Most Tailings Storage Facility (TSF) is the largest reservoir of post–flotation tailings in Europe. The total amount of tailings from the mines in Lubin, Rudna, and Polkowice are stored each year at the disposal facility, which reaches approximately 30 million tons. It is crucial to accurately monitor and maintain such a huge storage facility, for the safety and economics of the entire region. In general, the monitoring network installed at the Zelazny Most TSF includes four groups of components: (a) geotechnical network (VW pore pressure transducers and inclinometers), (b) hydrological network (open piezometers, water level gauges, drainage discharge measurements, (c) geodetic survey network (e.g. surface and in-depth benchmarks, laser measurements, GPS measurements within GEOMOS network and (d) seismic network (e.g. accelerometer stations, cone penetration tests.) Apart from the above, chemical water analyses, tests of soil samples, monitoring of spigotting processes, and monitoring of relief wells’ discharge are also conducted. In total, approximately 2900 monitoring instruments are installed within the area of the Zelazny Most TSF. Such large amounts of data from the various information sources makes manual data analysis by the engineers almost impossible. In this paper we discuss a machine learning driven approach to improve the quality of the monitoring and maintenance of such facilities. We focus on the seismic cone penetration test (SCPT) data analysis. First, we carefully describe the collected data, its quality and availability. Then we discuss possible events that can occur in the TSF that need to be predicted using SCPT. Based on the information obtained in these two steps, the applicability of several machine learning methods is estimated. Some of them are then tested on available historical data. The algorithms described in this article will be further developed in the IlluMINEation project (H2020).

Sep 1, 2021

By T. Puhakka

Simulation is a way to obtain quickly today future information on how planned systems will most likely behave in various selected situations. This information may then be used to optimize the system and its components and maximize the performance and output. Simulation is a way to fine-tune the layout, match the mobile fleet and optimize the schedule and the way of working to meet the desired production requirements. Simulation provides a glimpse of the upcoming operation, ‘future today’ and helps to predict its restrictions and sensitivity to various aspects. OptiMine™, the Sandvik Tamrock Corp. and CyberCube Oy developed simulation tool is designed to simulate underground rock flow and match suitable technology with various layout options. This tool can be used to view what-if situations and determine what kind of impact mastered changes have to production. The findings of critical points in the layout and working procedures at an early stage of a new mine can help to optimize the layout and material flow. OptiMine™is modular based simulation tool that combines the supplier machine knowledge and traffic guidance with mine operational know-how and mine environment. It is developed to work in a way that an effect of an individual incident, such as the effect of one additional turn in a continuous loading cycle to the daily capacity can be identified. The reported output can be used for economical impact evaluation of selected options. This paper discusses the use of simulation in general and the way the OptiMine™ simulation tool operates and how it may be used for operation, technology and material flow optimization.

Sep 1, 2001

By S. Budavari, F. M. C. C. Vieira

For several decades, the deep, gold-bearing reefs of the Witwatersrand basin have been mined predominantly according to layouts characterised by longwalls with strike pillars to provide regional support. During the past few years, a new generation of mining layouts has been introduced. These layouts are based on the concept of grid-type, scattered mining with dip pillars for regional support. As the extraction of the gold reefs extends to depths below 3500 m, the hazards associated with mining at these ultra-depths are expected to increase to unacceptable levels. Therefore, the question arises as to, which of the currently applied mining layouts is most acceptable for the economic and safe extraction of an ultra-deep orebody. The purpose of this paper is to describe a research investigation carried out to evaluate the degree of acceptability, from the rock engineering view point, of four currently used mining layouts for application at a depth-range of between 3500 and 5000 m. Pendant plusieurs décades, les filons d’or profonds du bassin du Witwatersrand ont été exploités d’une manière prédominante selon des dispositions caractérisées par des longues tailles avec des piliers directionnels pour donner un support local. Les dernières années ont vu la naissance d’une nouvelle génération de dispositions de mine. Ces dispositions sont basées sur le concept d’extraction type grille, éparpillée, avec des piliers au pendage pour le support local. Comme l’extraction des filons d’or va à des profondeurs en dessous de 3500m, il faut s’attendre à ce que les risques associés à l’exploitation à ces profondeurs extrêmes atteignent des niveaux inacceptables. Par conséquent, la question se pose de savoir laquelle des dispositions de mine couramment utilisées est la plus acceptable pour l’extraction rentable et sans danger d’un gisement ultra profond. Le but de l’étude présente est de décrire les recherches exécutées pour évaluer le degré d’acceptabilité, du point de vue d’ingénierie de roche, de quatre dispositions de mine couramment utilisées pour application à un rayon de profondeur entre 3500 et 5000m. Die tiefen, goldträchtigen Riffs des Witwatersrandbeckens wurden über einige Jahrzehnte hindurch vorwiegend nach jenen Layouts abgebaut, die von Langfrontstreben mit Schlagpfeilern charakterisiert waren, um regionale Unterstützung zu gewährleisten. Während der letzten Jahre wurde eine neue Generation von Grubenlayouts eingeführt. Diese Layouts basieren auf dem Konzept der Rasterfeld-Art, gestreuter Bergbau mit Neigungspfeilern für regionale Unterstützung. Es kann erwartet werden, daß auf Grund der Tatsache, daß sich die Extraktion der Goldriffs auf Tiefen unterhalb 3500 m verlagert, die Gefahren, die mit dem Bergbau an diesen Ultratiefen verbunden sind, sich auf ein nicht annehmbares Niveau erhöhen. Folglich erhebt sich die Frage, welche der gegenwärtig angewendete Abbaulayouts für die ökonomische und sichere Extraktion eines ultra-tiefen Erzkörpers am annehmbarsten ist. Zweck dieser Arbeit ist es, eine durchgeführte Untersuchung zu beschreiben, die vom Gesichtspunkt der Gesteinstechnik gesehen, vier gegenwärtig angewandte Abbaulayouts für den Einsatz in einem Tiefenbereich zwischen 3.500 und 5.000 m evaluiert.

Jan 1, 2003

What is the role of The South African Institute of Mining and Metallurgy at a time when so much is developing and changing in South Africa? The minerals industry is represented through employers, employees, government, education, research, public views, and even pure political interests. The role of the Institute is to represent the mining and metallurgical profession. In this role the Institute has aligned itself with Associated Scientific and Technical Societies, the Council of Scientific Societies and the Engineering Association. The Institute is also active on the Engineering Council of South Africa.

Jan 1, 1996

By J. Mulenshi, J. Rosenkranz, P. Khavari, S. C. Chelgani

The geometallurgical concept has mainly been applied to primary ore deposits, starting from ore characterisation to the economic optimisation of the mining operation. However, as primary ore resources are becoming depleted and lower in grade, alternative sources need to be explored and a question of adaptability of the geometallurgical approach to the secondary resource repositories arises. The particle size distribution, chemical and mineralogical compositions of the Smaltjärnen historical tungsten tailings from physical separation in Yxsjöberg, Sweden were studied using drill core samples collected from different locations within the tailings repository in order to assess the amenability of the tailings to reprocessing. The tailings are dominated by the –600 to +149 μm particle size fraction. This fraction contains most of the elements of interest (W, Cu, S, Sn, Zn, Be, Bi and F) hosted by scheelite, chalcopyrite, pyrrhotite, cassiterite, danalite (both Zn and Be), bismuthinite and fluorite, respectively. The particle size distribution and mineralogical composition vary across the repository, suggesting a possible existence of geometallurgical domains, which require further assessment to evaluate metallurgical performance. Keywords: Historical tailings, tungsten, scheelite, geometallurgy, characterisation, mineralogy, reprocessing

Jan 1, 2020

By L. A. Cornish, I. A. Mwamba, R. A. Couperthwaite

"In previous work by the authors, it was established that additions of 0.2 at.% Ru to an Fe-40 at.% Al alloy improved the corrosion and oxidation resistance of the alloy. The alloy was produced by mechanical alloying and spark plasma sintering and the work showed that nonequilibrium processing was able to significantly refine the grain size of the material. The sintered material had a higher hardness than the as-cast material and the change in grain size did not significantly affect the oxidation and corrosion. In the present research, the mechanically alloyed powder was coated onto a mild steel substrate using cold-spray coating at a gas pressure of 10 bar and a temperature of 500°C. The coatings were found to be 5–10 um thick, although thicknesses of up to 30 um were observed. The coated materials were subjected to oxidation and corrosion tests to determine the effectiveness of the coating in increasing the oxidation and corrosion resistance of mild steel. This was done to determine the effectiveness of cold-spray coating as a technique to coat these mechanically alloyed powders. IntroductionPrevious work conducted by Mintek (Couperthwaite et al., 2013, 2015) investigated the effect of precious metal additions on the structure, oxidation and corrosion properties of an Fe-40 at.% Al (Fe- Al) alloy. Initial work determined that additions of more than 0.5 at.% precious metal did not improve the oxidation and corrosion properties of the materials and in some cases even decreased the resistance to corrosion. Further work identified Pt and Ru as beneficial additions to the FeAl alloy. Four alloys were then produced by mechanical alloying and sintering (FeAl–0.2 at.% Pd, FeAl–0.2 at.% Ru, FeAl–0.5 at.% Ag, FeAl–0.5 at.% Pt). These alloys were all successfully produced by melting and casting and mechanical alloying sintering and it was found that the nonequilibrium processing greatly decreased the grain size of the materials compared to the ascast materials. It was found that the additions of Ru and Pt were still the most beneficial to the oxidation and corrosion properties, with Ru being considered the most beneficial."

Jan 1, 2016

By R. M. Kear

The Mine Planning Department of Rio Tinto Management Services South Africa has installed an interactive graphic work station to assist with the long- term mine planning of Palabora. Previously, the planning was drafted manually after which digitised areas were fed to the computerised ore reserve system. This method was slow, tedious, prone to error and was becoming incapable of meeting new planning parameters. To assist the planning engineer an interactive graphic system was developed, and subsequently a rewrite of the ore reserve reporting system was incorporated. The work station has reasonable computing power and, when not utilised for graphics, has been found suitable for the evaluation of various non- graphical applications, a recent example of which was the in-pit crusher investigation. This project, in contrast to similar studies, was not based on a fixed system throughput but rather on a well designed system which would be operated at its own optimum capacity. In order to determine the probable throughput a simple simulator was designed to model the crushing and conveying system. This paper describes the investigation into the specifications for the work station, the selection of hardware, operating system and languages. An over- view is then given of the graphic planning system. The in-pit crushing simulation has been included as an example of how the work station has been applied to other, non graphical, applications.

Jan 1, 1987

A General Meeting and Colloquium was held in Kelvin House, Johannesburg on Wednesday 29th September, 1971. The theme of the Colloquium was "The Ferro-alloy Industry". Prof D. D. Howat (President) was in the Chair. The meeting was attended by 106 delegates and was opened by the President at 10.05 a.m. OBITUARY The President: "It is my sad duty to announce the death of G. C. Needham, Fellow, who joined the Institute in 1966 and passed away on 27th September, 1971. As a mark of respect to the memory of the deceased and in sympathy with the bereaved I would ask you all to rise and observe a few moments silence." MEMBERSHIP The President: "I have much pleasure in announcing that the names of the following candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute. Fellows: Richard Lloyd Blandy, Brian Roger Borton, Brian Teversham, Peter Donald Dickson. Members: Frederick Brian Peacock, Peter John Stacey, Kenneth Niles Thanstrom, Byron J. Hayley, Ian Flemming Buchan, Abraham Hercules le Roux. Graduate: Ian William Coy. Students: Peter Boesley J ames, Kenneth Brian Perel. TRANSFERS From Member to Fellow: Cecil Eugene Fivaz, Peter Edwards. From Student to Graduate: Roy Stavely Traviss. From Student to associate: William Mitchell. I welcome the new members to the Institute and congratulate those members who have been transferred to a higher grade. COLLOQUIUM The first paper, presented by Mr S. Selmer-Olsen, Consulting Metallurgist, Amcor Limited, on &apos;Trends in Ferro Alloy Production&apos; was published in the May issue of the Journal and comprised information and data relating to new developments in ferro alloy production in various parts of the world. This was followed by a paper-&apos;Conductivity and Viscosity Properties of Slags produced in ferro-alloy manufacture&apos; by D. 1. Ossin et al. This was a record of laboratory test work on slags containing both lime and magnesia, corresponding with the composition of slags encountered in the production of ferro chrome alloys when a dolomite flux is employed. The third paper-&apos;Review of the work of the Pyrometallurgical Research Group of N.I.M. and Metallurgy Department, Wits.&apos; presented by Dr P. R. Jochens, leader of the Research Group, outlined the progress made on ten different research projects presently under way in the Department of Metallurgy. These projects range from studies of the kinetics and mechanism of the reduction of chromite ores through the determination of the activities of MnO in slags to phase studies and melting point determinations in the alloy systems Cr-Fe-Si-C and Cr-Fe-Si. A new feature of this Colloquium was the introduction of the discussion panel composed of four or five individuals known to have special knowledge or interest in the subject under duscussion. Mr J. J. Coetzee was chairman of the first panel, Professor D. D. Howat of the second and Dr R. E. Robinson of the third. During the discussion of Mr Selmer-Olsen&apos;s paper an interesting contribution was made by Mr Jack Hayley of Transalloys (Pty.) Limited who pointed out that the lowest power cost in the U.S.A. was that from the TV A at 6 mils per unit (0,43 cents S.A.) while costs from other sources were 7 to 8 mils per unit (0,50 to 0,57 cents S.A.) He also referred to the use of &apos;pile sintering&apos; of ore fines plus coke at certain ferro alloy plants in the V.S. and to the recent practice of &apos;graphitising&apos; the paste used for Soderberg electrodes. The last session in the afternoon was devoted to a group discussion on &apos;Practical problems in Arc Furnace Operation&apos;, Mr H. R. Reid of Middelburg Steel Alloys (Pty) Limited occupying the chair, members of the panel being Mr J. Meintjies (Rand Carbide Limited), Mr J. Benn (Amcor) and Mr E. J. Jackson (Transalloys (Pty.) Limited). Mr Reid initiated the discussion by talking of the design and composition of electrode shoes, mentioning the use of the 85/15 Cu/Zn alloy and the comparison of hollow shoes and shoes cooled by tubes. Mr Meintjies discussed electrode management with particular reference to breakages, and dealt with casing and fin design and the welding of fins. Mr Benn dealt with aspects of closed top furnace operation with particular reference to the control of eruptions in the furnace and indicated that preheating of the raw materials might be well worth considering together with the development of a system for the detection of the water vapour present. Mr J ackson was concerned with shells, linings, refractories and tap holes. He deprecated the use of oxygen for opening the tap hole emphasising how uncontrolled use of oxygen led to loss of shape of the tap hole and quite severe burning out of the front hole resulting in time and labour in repairs. A notable feature of the Colloquium was the free discussion &apos;from the floor&apos; of the hall. Many valuable and highly pertinent contributions were made spontaneously and usually in reply to some controversial topic raised by the discussion group.