Search Documents

By K. Koruyan

Although remote sensing technology has been available for many years, it has rarely been used for monitoring mining activity. Recent studies indicate that remote sensing is also a valuable tool for managing and planning certain aspects of the mining operation. In this paper, we examine areal expansion of marble quarries and the affected vegetation over a period of 10 years in the Mugla region in Turkey, using geographic information system (GIS) and remote sensing (RS) techniques. Images captured by ASTER Level 3A01 (3D Ortho Data Set), Landsat 5, and Landsat 7 satellites between 2001 and 2009 were used for the analysis. Changes in the natural vegetation as a function of the production level in the marble quarry were calculated using the normalized difference vegetation index. According to the study results, land cover and natural vegetation decreased by less than 3 per cent and 1 per cent respectively between 2001 and 2009, following an upsurge in mining activity in the region.

Jan 1, 2012

By D. R. Tesarik, F. M. Jones, J. B. Seymour

As part of safety and stability studies at three underground mines in the United States, researchers installed earth pressure cells and embedment strain gauges in cemented rockfill to measure stress and strain changes as mining progressed and the rockfill was loaded. Data from these instruments were used to calculate the in situ modulus of the rockfill for two of the mines. A three-dimensional numerical model of a cemented rockfill cap was validated with data from extensometers anchored in the mine roof and sill; this model was then used to estimate deformation modulus at the third mine because the earth pressure cells and embedment strain gauges recorded negligible changes. Rockfill binder used at these mines ranged from 4 to 8 per cent of the dry components by weight, the water-to-cement ratio was from 0.42 to1.0, and the largest aggregate size in the three mixes ranged from 5 to12 cm (2 to 4.7 in). The range of the calculated in situ deformation modulus values was large, but as expected, it was bracketed by modulus values for cemented tailings and roller-compacted concrete with similar cement contents and water-to-cement ratios. Dans le cadre d’études sur la sécurité et la stabilité de trois mines souterraines situées aux États-Unis, les chercheurs ont installé des palpeurs de pression des terres et des extensomètres d’encastrement dans les remblais cimentés afin de mesurer les variations relatives à l’effort et à la déformation des terrains durant l’exploitation minière et le chargement du remblai. Les données recueillies à l’aide de ces instruments ont servi au calcul du module in situ du remblai dans deux de ces mines. Le modèle numérique tridimensionnel de la semelle d’un remblai cimenté a été validé à partir des données recueillies par les extensomètres ancrés dans la voûte et dans la semelle de ces mines; ce modèle a ensuite été utilisé pour estimer le module de déformation à la troisième mine, étant donné que les palpeurs de pression des terres et les tensiomètres enfouis avaient relevés des variations négligeables. La matière d’agrégation de l’enrochement utilisée dans ces mines comportait entre 4 % et 8 % des composantes sèches par poids; le rapport eau-ciment se situait entre 0,42 et 1,0; et la taille des agrégats les plus gros dans ces trois mélanges était de 5 cm à 12 cm (2 po à 4,7 po). L’écart entre les valeurs calculées des modules de déformation in situ était grand, mais comme on s’y attendait, cet écart a été compensé par les valeurs modulaires des résidus cimentés et du béton tassé au rouleau avec des teneurs en ciment et des rapports eau-ciment semblables. Als Teil der Sicherheits- und Stabilitätsstudien an drei Bergwerken in den Vereinigten Staaten von Amerika installierten Forscher Erddruckgeber und Einbindungsdehnungsmesser in zementierter Steinschüttung, um Spannungs- und Dehnungsveränderungen während der fortlaufenden Bergarbeiten und der Belastung der Steinschüttung zu messen. Daten von diesen Instrumenten wurden dazu verwendet, das In-Situ-Modul der Steinschüt-ung für zwei Gruben zu berechnen. Ein dreidimensionales numerisches Modell einer zementierten Steinschüttungsschwelle wurde mit den Daten von den im Grubendach und in der Schwelle verankerten Extensometern validiert; dieses Modell wurde dann dazu eingesetzt, um das Deformationsmodul in der dritten Grube zu schätzen, da die Erddruckgeber und Einbindungsdehnungsmesser nur geringfügige Messabweichungen feststellten. Das in diesen Gruben verwendete Steinschüttungsbindemittel variierte zwischen vier und acht Prozent an Trockenkomponenten nach Gewicht, der Wasser-Zementfaktor betrug zwischen 0,42 und 1,0 und die größte Zuschlagstoff-größe in den drei Mischungen schwankte zwischen fünf und zwölf Zentimetern. Die Reichweite der berechneten Werte des In-Situ-Deformationsmoduls fiel etwas breit aus, aber es fand erwartungsgemäß eine Klammerung der Modulwerte zwischen den Zemen-trückständen und dem durch Walzen verdichteten Beton mit ähnlichem Zementanteil und Wasser-Zementfaktor statt.

Jan 1, 2003

By B. Talbot

How this simple plant generates a large revenue stream. The concept behind the Tailings Scavenging Plant (TSP) is simple: it is a non-complicated modular plant which is designed to be more stable than upstream plants. This, plus the use of ?high energy?, enables the plant to recover any metal missed by the upstream operation. Impala Platinum?Mineral process started pilot plant exercises in June 2003. The pilot plant ran for one year before the capital for the full-scale plant was approved. This year was used to motivate, design and cost a full-scale plant. The metal produced during the pilot and feasibility study enabled this part of the project to run at a small profit. The scale-up to full-scale was relatively simple as the pilot plant had a capacity of 180 m3/hrand the full-scale plant was designed for a capacity of 550 m3/h. The design for the full scale plant was completed in May 2003, with ground breaking taking place on 19 May 2003. The construction phase of the project went well with the commissioning of the first two modules taking place on 22 October 2003. The remaining two modules were commissioned two weeks later. The plant was at full capacity by the 20 November 2003. A review of the plants performance for the first 5 production months is as follows: the plant has required only a few minor modifications and additions, it has run well in excess of 95%availability with no major wear apparent. In addition to this, the plant has produced 3 times the metal forecast.

Jan 1, 2004

By Q. Li, B. Ricks

Over the last several decades mineral concentrate long distance slurry pipelines have been installed and successfully operated. Nearly all were installed via the buried construction method. Their record of depend ability and economy has been well proven. However, these systems operate in regions where seasonal soil frost penetration is shallow or non-existent. In recent years interest in long distance mineral concentrate pipelines in northern cold regions has been increasing. For cold regions one must consider seasonal temperatures and soil frost penetration in order to ensure reliable operations through the year. Herein a case study is developed where heat balance and temperatures for small and large diameter long distance slurry pipelines are compared. The study development is as follows: ?Rheological properties are analysed over range of temperatures from near freezing (4ºC; 39ºF) to relatively very warm (40ºC; 104ºF). ?Then assuming similar climatic conditions, soil properties, and pipeline length, a study is carried out for two pipeline diameters, namely: a small diameter (nominal8 inch; 219.1 mm) and a large diameter (22 inch; 558.8 mm). ?The study focus is on maintaining slurry temperature above freezing throughout the pipeline length by illustrating a decision based on burial depth versus coating the pipeline with insulation.

Jan 1, 2007

By B. J. Madden

The formula developed by Salamon and Munro in 1967 has been used for the past 22 years in the design of bord-and-pillar workings in South African collieries. This paper re-assesses the formula In the light of Its past performance and examines the effect of mining method on coal-pillar strength. An account is given of the extension of the formula so that it can be applied beyond the empirical range for which it was derived, and the advantages of the extended formula (the squat-pillar formula) are described.

Jan 1, 1991

By R. S. Francis

There are no manuals or handbooks for budding mill superintendents or process plant managers. Most who obtain this level of responsibility have gained their training from watching the good and bad of their predecessors and the successful ones have themselves graduated from the school of hard knocks. This paper attempts to provide some helpful guidelines and direction for those who aspire to better manage a mineral processing facility. The authors have 20 years combined experience in senior management roles at nine different mineral processing operations in Australia and overseas, covering gold, base metals and mineral sands. This summary of tips and pitfalls will hopefully benefit future leaders in mineral processing and metallurgy.

Jan 1, 2007

By H. E. Bartlett

Previously, the grade of ore at the shaft head was taken to be equivalent to the grade measured in the faces by means of chip sampling. The tonnage mined from the stopes is determined from survey volumetric measurements. Estimates of shaft head grade and tons include the grades and tons of waste, development ore, sweepings from old areas, and other sources, not all of which are sampled. The tonnage of ore delivered at the shaft is often estimated using skip factors. These factors are subject to manipulation and not all the skips are filled to the same level. Consequently, both the grade and tonnage of ore delivered at shaft head are subject to a measure of uncertainty. For many years, these uncertainties have led to disputes between shaft managers and metallurgists over the reconciliation between shaft tons and grade and plant tons and grade. These problems are compounded when several shafts feed a central processing plant. Shaft bonuses and a shaft?s profitability are affected by poor gold allocation methods. Without measurement of the grade and tonnage from all shafts, a poorly performing shaft could benefit at the expense of the other shafts. In order to improve the measurement of grades and tonnage at the shaft head, which is the custody transfer point between the mine and surface operations, South African mining companies have developed a methodology to measure the mass of ore from each shaft using rail weighing equipment, and the run-of-mine grades delivered from each shaft using cross-stream (go-belt) sampling. Harmony Gold Mining Company has implemented the rail weighing and go-belt sampling methods for their shafts. This paper deals with the statistical tests on the procedures and control measures that are in place to establish confidence in the gold allocations. The metal accounting system for examining the allocations follows the first principle of the AMIRA P754 Metal Accounting Code of Practice namely ?The metal accounting system must be based on accurate measurements of mass and metal content. It must be based on a full check-in check-out system?. The check-in is mass and grade of run-of-mine ore and the check-outs are the plant input grades and the recovery and residue from the plant. The balances between check-in and check-out are the subject of the statistical analyses, which have been conducted using the classical statistical tests and procedures that are generally used in all fields of endeavour. It is concluded that the gold allocation procedures that rely on go-belt sampling and rail weighing of ore from shafts has been successfully implemented, and that the system, which has been in operation at Harmony since 1993, has won general acceptance from stakeholders, with the gold allocations being perceived as being fair to all. Apart from the on-mine issues of bonuses and fair allocations, accurate metal accounting assists in the broader issues of generating accurate production figures for management. An added benefit of weighing and sampling ore at the shaft head has been that shafts now have daily moving average grades, which are used for grade control. The go-belt sample at the shaft head is the first accurate sample of production in the value chain from face sampling to gold bullion. Keywords metal accounting, go-belt sampling, run-of-mine sampling, codes of practice, AMIRA P754, train weighing, statistical analysis, gold split, allocation of gold, metal balance, grade control.

Jan 1, 2014

By M. Faure

The experiment with backfill at Harmony was mainly an attempt to improve the ground conditions in a particularly tricky section of the mine. A deslimed tailings system was selected for financial reasons, ease of installation, ease of operation and its low level of mechanization. The design of the system has three aspects: firstly, to define the parameters of the backfill material itself; secondly, to design a reliable plant which could consistently produce the desired material in sufficient quantities; and, thirdly, to design a fill distribution system for maximum reliability in the shaft, minimum pipe line velocity, pressure and cost in the horizontal sections and consistency and reliability at the delivery end. The system was successfully constructed and commissioned in a short space of time at a relatively low cost. It has now reached its full potential, and very encouraging results have been achieved with regard to cost savings, ground conditions, ventilation and accident statistics.

Jan 1, 1988

By C. K. Chabedi

"This paper discusses the difficulties associated with the potential exploitation of the deep multi-seam resources east of the Daarby fault in the Waterberg coalfield. The resources occur at a depth greater than 250 m and the thickness of the coal is roughly 110 m, but the top 50 m comprises coal intercalated with shale and the bottom 60 m contains five seams with sandstone and shale partings. Various factors affecting multiple seam mining at these great depths are discussed with reference to lessons learned from local and international experience on multi-seam mining. Field geological and geotechnical data was utilized to assess the stability of the roof of the seams. There is no specific rock mass rating for the Waterberg area, therefore approximate coal mine roof rating (CMRR) values were used to propose appropriate support strategies. Analysis of Multiple Seam Stability (AMSS) was used to analyse the strength of the parting or interburden between the various seams, the mining sequence, and the interaction between the various seams.The research indicated that it is possible to mine seams with a low CMRR at high mining rates using longwall mining, although support for gateroads is expected to be expensive, time-consuming and onerous to install, and will impact gateroad development rates. It will not be possible to simultaneously mine zones in close proximity and failure of the interburden is predicted, thus dangerous mining conditions are anticipated. However, it will be possible to mine just two of the eleven zones using longwall mining. IntroductionThis paper discusses the difficulties associated with the potential exploitation of the deep multi-seam resources east of the Daarby fault in the Waterberg coalfield using bord and pillar and longwall mining. Figure 1 illustrates the location of the Waterberg coalfield relative to other coalfields in South Africa, while Figure 2 shows the areas containing deep and shallow resources. The Waterberg resources are expected to contribute to South Africa’s future energy requirements, and are currently exploited at the Grootegeluk open pit mine. Grootegeluk produces coal mainly for a power station, with the higher quality product supplied as metallurgical coal. The deposit is technically unique and challenging, being a multi-seam coal deposit with a total of 12 seams over a thickness of 110 m as shown in Figure 3, including Zone 5. There is currently limited knowledge on the multi-seam mining of the deep Waterberg resources. Multi-seam mining utilizing the bord and pillar method has been practised in South Africa before, but at a depth of less than 100 m in the Witbank coalfields. Multi-seam mining in thin seams has also been performed in the Natal coalfields at a depth of less than 160 m, but mostly using bord and pillar mining and secondary mining (partial pillar extraction)."

Jan 1, 2016

By H. A. D. Kirsten

The structural competence of mesh- and fibre-reinforced shotcrete was investigated in two series of tests on full-scale panels. It was found that uniformly distributed loading was marginally less demanding than point loading, mesh reinforcement was superior to fibre reinforcement, Dramix fibre and Melt Extract fibre were similar in reinforcing characteristics, and 30 mm to 35 mm was an optimum fibre length. Furthermore, the consistency of the fibre content could not be assured on practical mining sites, and an average fibre content of about 1,5 per cent was the maximum that could be obtained for fibre lengths not exceeding 35 mm. Also, owing to its greater flexibility, shotcrete reinforced with diamond mesh was preferable to fibre-reinforced shotcrete in mining excavations subject to squeezing conditions. In view of the difficulties associated with assuring the consistency of the fibre content in mining applications, it appears that the sophisticated attributes of fibre-reinforced shotcrete can be effectively exploited only in civil-engineering applications in which quality assurance is subject to explicit contractual control. Load-deflection curves, together with measurements of compressive stresses in the surfaces of some of the panels, enabled the ultimate flexural strength of reinforced shotcrete to be rigorously formulated, and rigorous design procedures for shotcrete subject to bending and direct thrust to be developed. The application of the procedures is demonstrated in a practical design case in which the moments and thrusts in a tunnel lining are determined in a numerical analysis of the interaction between the lining, the surrounding rock, and the rock-reinforcing system.

Jan 1, 1992

By D. Van Dyk

Horizontal rotating mills are being used all over the world in different mineral and power generation industries. David Brown South Africa, with over 140 years of experience in gear manufacture and design, has been supplying these industries with innovative designs at exceptional quality. The gearing systems associated with these industries are challenged daily with operating conditions that are not always fully understood. Failures are therefore experienced, over time in the industry, which cannot always be fully explained. David Brown South Africa has developed a gear monitoring system, the Intelligent Gearing System, in association with Transmission Dynamics (UK), in order to monitor and analyse these operating conditions in real time. The system has been designed on the principles of Six Sigma, incorporating Design for Six Sigma. The purpose with this system design is to monitor the operating conditions on the pinion, record the information and analyse the data in relation to the rate of fatigue damage to the girth gear and pinion. This is done in real time and unattended. The output from the Intelligent Gearing System can be fed back into the operating system of the mill user, in order to display an alarm for operating conditions exceeding the design criteria as well as information on the rate of fatigue damage due to these operating conditions. When the mill operating and the effect on the fatigue life of the mill gearing components, conditions are better understood, mill users can forecast critical spare holding levels with an increased accuracy. The Intelligent Gearing System also allows early actions to remove reasons for system overloads.

Jan 1, 2006

The Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House on Wednesday, 23rd August, 1978. Mr P. A. von Wielligh (President) was in the chair and declared the meeting open at 16h00. Obituaries The President: It is my sad duty to announce the death of the following members of the Institute : T. K. Prentice and W. E. Gooday, Honorary Life Fellows and Past Presidents; B. S. Allen, J. A. Becking, L. H. Mellor, C. A. Pratt and W. T. Stobart, Life Fellows; J. P. Burls, E. Cameron, M. L. Fitzgerald, C. G. Hinds, A. J. Patrick, H. O. Reisener, N. D. Shuttleworth, N. Soldan and J. Whitehouse, Fellows; T. Gemmell, J. S. A. Oelofse, W. D. Rowe, R. L. J. Shearman and G. M. Thain, Associates. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I ask you to rise and observe a few moments' silence. Welcome The President: It is now my very pleasant duty to welcome our distinguished guests and visitors. We are pleased to have with us Mr D. A. Etheredge, Vice¬President of the Chamber of Mines of South Africa, and Mrs Etheredge. Mr Etheredge this afternoon represents the mining industry at our meeting. The importance of the close link that over the years has been maintained between the industry and our Institute speaks for itself. We are, therefore, grateful that he and Mrs Etheredge have managed to find the time to be with us this after¬noon.

Jan 1, 1979

By R. A. Wildenboer, R. F. Sandenbergh

Rare earth elements (REE) are present at concentrations of approximately 0.36 % in phosphogypsum stacks located in Phalaborwa, South Africa. The REE are present in the phosphogypsum in solid solution in the gypsum and as fluorine and aluminium rich precipitates. Recovery of the REE offers opportunities for valorization and reducing the environmental impact of the phosphogypsum waste. This paper presents the results of investigations into the leaching behaviour of rare earth elements and other impurities from phosphogypsum using aqueous sulfuric acid. The effects of acid concentration, temperature, residence time, and the influence of impurities were evaluated for their impact on the solubility of rare earth elements in a sulfate medium. It was found that a significant fraction of the REE can be leached from the phosphogypsum in a range of conditions much less severe than traditional hard rock rare earth processing conditions. The REE were leached at a sulfuric acid concentration of 110 g/l, temperature of 30°C – 40°C and a residence time of approximately 8 hours.

Nov 6, 2024

By E. Keskinkilic

In this study, sulfide-type inclusion morphologies of a Ca-treated hot-rolled wheel steel, Grade-X, were investigated. The specimens taken from the hot-rolled products of Grade-X heats were studied. The size and distribution of elongated sulfide inclusions were examined for the heats of different S levels. Elongated sulfide inclusions were either not observed or rarely encountered when ladle analysis S content was below 50 ppm. The size and relative abundance of sulfide inclusions were reported to increase markedly when the S composition was greater than or equal to 70 ppm and the Ca/S ratio was less than 0.50. The effect of Ti addition (0.010?0.020% Ti) on sulfide-type inclusion morphologies was then investigated for heats having a sulfur content higher than 50 ppm. Addition of Ti was found to have a partial effect on decreasing the size of sulfide-type inclusions under real steelmaking conditions. Keywords Sulfide inclusions, Ca-treatment, titanium.

Jan 1, 2011

By L. Bam, R. Machaka, S. Chikosha, N. S. Muchavi

"Parts manufactured through power metallurgy (PM) typically contain pores that can be detrimental to the final mechanical properties. This paper explores the merits of 3D X-ray computed tomography over traditional microscopy for the characterization of the evolution of porosity in metal injection moulding (MIM) and direct powder rolling (DPR) products. 17-4 PH stainless steel (as-moulded, as-debound and sintered) dog-bone samples produced via MIM and Ti-HDH strips (as-rolled and sintered) produced via DPR and were analysed for porosity. 3D microfocus X-ray tomography (XCT) analysis on specimens from both processes revealed spatial variations in densities and the existence of characteristic moulding and roll compaction defects in agreement with traditional microscopic microstructural analysis. It was concluded that micro-focus XCT scanning can be used to study MIM and DPR parts for the characterization of the amount, position and distribution of porosity and other defects. However, the majority of the sub-micron sized pores could not be clearly resolved even at the highest possible instrument resolution. Higher-resolution scans such as nano-focus XCT could be utilized in order to fully study the porosity in MIM and DPR parts. IntroductionMetal injection moulding (MIM) is a novel process, which combines the advantages of powder metallurgy (PM) and plastic injection moulding. MIM has found widespread applications in the cost-effective production of high-sintered density small parts with complicated shapes and mechanical properties equivalent to those of wrought materials (German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013). There are four basic processing steps involved in MIM, namely; feedstock preparation, injection moulding, debinding and sintering. These steps are discussed in greater detail elsewhere (Machaka, Seerane and Chikwanda, 2014; German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013).Feedstock preparation involves mixing metal powder with a carefully selected composition of polymeric binder materials at a specific temperature. The feedstock is then granulated and injected into a predefined mould die with the desired shape. The part produced during the moulding step is referred to as a ‘green’ component. The green component typically contains no porosity since the spaces between adjacent powder particles are readily filled with the binder materials (German and Bose, 1977; Li, Li and Khalil, 2007). Debinding is the systemic removal of the binder components by chemical, catalytic, or/and thermal means while maintaining the shape of the component. The part produced after the debinding step is referred to as a ‘brown’ component. Debinding is known to be the source of porosity in brown components (Ji et al., 2001; Tsai and Cen, 1995). Finally, the brown debound part is sintered to full or nearfull density (Sotomayor, Varez and Levenfeld, 2010). The sintering step and associated densification closes up the majority of the pores. Sintered MIM parts are typically sintered to high density (95–99%) and retain an irreducible amount of residual porosity (Barriere, Liu and Gelin, 2003; German, 1990)."

Jan 1, 2016

Review Mining annual review June 1979. London, Mining Journal, 1979. 624 pp. Available as part of the subscription to the Mining Journal or at £12,50 per copy. This annual review is recognized internationally as the world leader in reporting on metals and minerals, and is eagerly awaited each year for its authoritative content, which is compiled by well-respected experts throughout the world.

Jan 1, 1979

By A. A. Bradley, P. J. D. Lloyd, A. J. Freemantle

Developments in centrifugal milling by A. A. BRADLEY,B.Sc. (Rhodes) (Visitor), A. J. FREEMANTLE, B.Sc. Hons. (Wits) (Visitor), and P. J. D. LLOYD, B.Sc. (Chem. Eng.), Ph.D. (Cape) (Fellow) The theoretical and experimental results of a study of centrifugalmills are reviewed. Means for the scaling up of such mills are suggested, and tests on a prototype mill are described. Despite the high lining wear in the centrifugal machine, which reduces its productive availability, its other advantages suggest that there is merit in pursuing its further development.

Jan 6, 1974

By M. J. Nicol, R. P. Colborn

An investigation into the kinetics and mechanism of the oxidation of iron (11) by oxygen in aqueous chloride solutions By R. P. COLBORN Pr. Eng., Ph.D. (Natal) and M. J. NICOLt B.Sc. Hons., Ph.D. (Rand) A reaction mechanism for the oxidation of ferrous chloride by molecular oxygen is developed. and the appropriate constants are evaluated. The effect of a number of cations and anions on the rate of oxidation has been tested.

By J. H. Venter

The accuracy of estimation from samples of ore in bulk By J. H. Venter Published in the Journal April 1972. ERRATA: Equation (1) should read... Equation (3) should read .... line following "Duscussion" Delete" .... Insert... above "References" "Discussion". Replace .... tenth DISCUSSION M. DA VID Professor Venter has proposed a formula to compute the variance of the estimated grade of a lot of broken ore, and interesting comments on the relevance of the formula and suggestions for developments are made by P. R. Janisch.

Jan 4, 1972

By L. D. Robbins, M. L. Murphy, A. C. Campbell, L. Murphy

This paper reports on what appears to be the first discovery of prehistoric mica-schist mining in southern 4frica. The mine concerned was found in a location very rich in rock art that is one of the most important archaeological sites in the Kalahari. The authors conclude that the oval pieces of mica schist that were found at the mine site were used by Khoisan peoples to scrape fatty tissue from hides that were to be cured. Radiocarbon datings seem to indicate that such ovals were used for at least 20 000 years.

Jan 1, 1994