Search Documents

By RUDULF KUDLICH

Pennsylvania anthracite coal is almost universally recognized to be the solid fuel best suited for domestic use when cleanliness , convenience and cost are considered . At various times and in various localities , however, conditions so affect the supply that it becomes insufficient or is too high in price and recourse must be had to other fuels as substitutes . In practically every district in the United States where anthracite has been the common domestic fuel , some other fuel is available as a substitute . In even the most severe climates such fuels are used either as emergency substitutes for anthracite , or as the ordinary domestic fuel . There may be some drawback to the use of such fuel , such as the need of more frequent attention to the furnace , smoke , soot and dust , in the case of solid fuels lower in price than anthracite , but these inconveniences must be accepted as necessary accompaniments to a decreased fuel bill . The cleanliness and ease of handling anthracite in the house must be considered in the light of a luxury and a higher cost of heating with this fuel must be expected . That a growing number of people are willing to pay for such added convenience is evident from the increasing mumber of heating installations using oil , gas and electricity , all of which are more convenient and usually more expensive even than anthracite .

Aug 1, 1923

Minimize the effects of underground mine conveyor belt fires by developing methods to prevent automatic fire suppression system failures. The Problem Fire protection is achieved by prevention, early detection, and planned fire-fighting response. Automatic fire suppression systems are one form of planned fire-fighting response. When these systems are properly designed, installed, and maintained they can effectively control fires. Conveyor belt fires account for about 20% of underground coal mine fires. Fire protection requirements have been established for underground locations because of potential for start and spread of fire and the restricted personnel egress in a fire situation. Belt conveyor systems arc potentially dangerous because of the high fire incidence rate, high temperatures, dense smoke, toxic gases, and rapid flame-spread rate. While investigating the conveyor fire suppression problem, the Bureau identified automatic fire suppression system reliability as a potentially serious deficiency within the mining industry. Table 1 lists common failure modes fur three Fire suppression system types. This table summarizes findings of Mine Safety and Health Administration electrical inspectors responsible for inspection of belt protection automatic fire suppression systems. Batteries, contact points, control wires, and electric servocontrols are all prone to failure. Figure 1 shows rock-dust-contaminated relay contact points. This condition is dangerous because of the chance of intermittent failures, which might allow systems to pass annual functional testing, yet fail during actual fire emergencies.

Jan 1, 1989

By Bruce T. Olenchuk, Wils L. Cooley

Electrical grounding is essential for the safe operation of power systems. A low-impedance path to ground is necessary to prevent the possibility of dangerously high potentials in human work areas. If for any reason this ground connection becomes faulty, a serious hazard may exist. One reason for faulty ground connections is ground bed corrosion. Corrosion of electrical ground rods has plagued the power industry and appeared in coal mine power systems. This paper will investigate ground rod corrosion, its cause, and possible solutions. Included is an evaluation of various ground rods for their ability to resist corrosion under stray current conditions. -The first known study of X-it3 Rod Corrosion is also presented.

Jan 1, 1979

By George J. Conroy

Techniques for locating trailing-cable faults are discussed, particularly those techniques suitable for use in underground coal mines, which have been the subjects of Bureau of Mines research. The discussion concerns precautions and suggestions for locating faults, rather than detailed descriptions of apparatus.

Jan 1, 1979

By Vijia K. Karra, John J. Sammarco, Robert Paddock, Edward F. Fries

Workers in hazardous environments such as mining are constantly exposed to the health and safety hazards of dynamic and unpredictable conditions. One approach to enable them to manage these hazards is to provide them with situational awareness: real-time data (environ-mental, physiological, and physical location data) obtained from wireless, wearable, smart sensor technologies deployed at the work area. The scope of this approach is limited to managing the hazards of the immediate work area for prevention purposes; it does not include technologies needed after a disaster. Three critical technologies emerge and converge to support this technical approach: smart-wearable sensors, wireless sensor networks, and low-power embedded computing. The major focus of this report is on smart sensors and wireless sensor networks. Wireless networks form the infrastructure to support the realization of situational awareness; therefore, there is a significant focus on wireless networks. Lastly, the “Future Research” section pulls together the three critical technologies by proposing applications that are relevant to mining. The applications are injured miner (person-down) detection; a wireless, wearable remote viewer; and an ultrawide band smart environment that enables localization and tracking of humans and resources. The smart environment could provide location data, physiological data, and communications (video, photos, graphical images, audio, and text messages).

Jan 4, 2007

By C. W. Smith

Research was conducted by the Bureau of Mines to determine the effectiveness of various types of crushers for use with the Bureau-developed pneumatic concentration technique for mica. Three types of crushers were investigated in this study, a roll crusher, a jaw crusher, and a hammer mill. All the mica concentrates produced contained over 82 percent mica, but recoveries varied considerably. The roll crusher gave the lowest recovery of 46 percent of the mica followed by the jaw crusher with a recovery of 50 percent of the mica. The hammer mill proved the most effective, producing four concentrates with recoveries of at least 70 percent.

Jan 1, 1981

By C. L. Severy

On the Pacific coast during World War II, a tremendous ship-building industry was developed, Early in the war it became impossible to obtain in- got or steel scrap for ship ballast. Magnetite, an oxide of iron, was sub- stituted as it fulfilled the requirements of weight for available space in the ships. Consequently, a new use for the western magnetite was rapidly developed.

Jan 1, 1948

By John Jordan, Steven J. Knoll, Douglas Tesarik, Theodore J. Williams, David K. Denton, Douglas F. Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because this condition can result in failures of ground that lead to both injuries and death. Personnel from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health studied two methods for identifying stress in rock. A seismic tomographic survey, finite-difference analysis, laboratory measurements of compression wave (ultrasonic) velocities in rock cores, and site geology were integrated to evaluate the use of seismic tomography for identifying induced pressures in an underground pillar at the Edgar Mine, Idaho Springs, CO. Electromagnetic (EM) emissions were also investigated in the Galena Mine, a deep underground mine in Idaho, in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results of this research indicated that (1) seismic tomography appears to be a useful tool for determining relative stress in underground pillars, while (2) EM emissions do not appear to be significant precursors of impending catastrophic ground failure.

Jan 1, 2004

By F. E. Brantley

Optimum autoclaving conditions were determined for separation of iron and manganese values from pregnant leach liquor produced in extracting manganese from low-grade umber are. The umber was leached with a synthetic anolyte similar to a recycle solution, used in manganese electrolysis cell operations, that had been renewed with ferrous sulfate and sulfuric acid. The equipment used and results obtained are presented for the several conditions employed. The kinetics of the separation were studied. Rate equations were derived for the formation of solid ammonium-manganese sulfate, (NH4)2 Mn2 (S04)3.

Jan 1, 1968

By Wilder D. Foster

In estimating the hazardous qualities of a dusty atmosphere it is frequently desirable to determine the composition of the air-borne dust. Samples collected from ledges or from the rock itself are likely to be unsatisfactory for this purpose owing to the possibilities of differential disintegration of the rock and of variations in settling rates of the different components of the minerals. It may be necessary, therefore, to collect samples of dust from the air. Samples collected from the air may be analyzed chemically, by X-ray diffraction, and by the petrogrephic microscope. Chemical methods are unsatisfactory owing to the small samples usually available and to the limitations and complexities of present methods. X-ray technique requires expensive apparatus not ordinarily available except in research laboratories. Owing to the simplicity and rapidity of petrographic examination of atmospheric mineral dusts, it was considered worthy of further study.

Jan 1, 1938

By Robert P. Vinson

The U.S. Bureau of Mines evaluated a light-scattering technique for discriminating between spherical and nonspherical particles. This evaluation was a three-step procedure. The first step required collecting light-scattering data for a variety of particles. This was accomplished with a particle analyzer called the DAWN-A. The DAWN-A measured the scattered light intensities of individual particles at a forward scattering angle of 40°. These DAWN-A measurements of individual particles are called scattering signatures by the Bureau researchers. The second step in this evaluation was to calculate a sphericity index number using the scattering signatures produced by the DAWN-A. The sphericity index number can range from 0 to 1. A calculated sphericity index of 1 would show that based on the intensity of scattered light, the particle was a perfect sphere. The third and final step of this evaluation was the comparison of the calculated sphericity indices of the various particles. Comparing these indices made it possible to discriminate between the nearly spherical waterdrops and the nonspherical coal and rock dust particles.

Jan 1, 1993

By Alan R. Buehler

A mineral survey of the 20,792-acre Sand Butte WSA (Wilderness study Area), ID-57-8, was conducted by U.S. Bureau of Mines personnel in 1985, at the request of the Bureau of Land Management. The WSA is in Lincoln County, south-central Idaho, about 15 miles south-southeast of Carey. There are no mines, prospects, or claims within the WSA. Basaltic lava is the only rock type exposed within the WSA. The only mineral resource is a few tons of a platy variety of lava (slab pahoehoe) which is suitable for use as decorative stone. Similar slab pahoehoe, produced from other lava fields in southern Idaho, retails for approximately $125/ton. The deposit in the WSA is too small to be mined commercially but may have value to consumers who gather their own decorative stone. INTRODUCTION A mineral survey of the Sand Butte WSA (Wilderness Study Area) 1/ was conducted in June 1985 by the USBM (U.S. Bureau of Mines) and the USGS (U.S. Geological Survey) at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will he used to help determine the suitability of the WSA for inclusion into the National Wilderness Preservation System. The immediate goal of this and other USBM mineral surveys is to provide data to the President, Congress, government agencies, and the public for land-use decisions. The long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By D. J. Bauer

A pure scandium solution was concentrated from 10-4 mole per liter to 0.5 mole per liter by continuous foam fractionation in a spaced, packed column. Recovery in the foam was 77 percent using a spaced, packed draining column with sodium n-methyl-n-"coconut oil acid" taurate as the surfactant. The technique was first studied batchwise in a small unpacked column to determine the more important variables. Optimum surfactant concentration was found to depend on scandium concentration. Extraction and, in general, enrichment ratios were highest in the 2.5 to 3.5 pH range at temperatures ranging from 50° to 70° C. An airflow rate of 136 ml./min. was satisfactory in the equipment used.

Jan 1, 1962

By Carlton E. Brown

In 1935 , Brown and Yant / described a microprojector ( microscopic arrangement for projecting images on a screen ) for use in counting and measuring the size of dust particles in Owens - jet dust - counter and simila dry samples of dust collected from the air . In 1938 Brown and others , described a modification of this microprojector that could be used also in counting dust in impinger samples . Microprojectors of this second type have been set up by many mining companies and others and have been made commercially available . Hamly and Pullen5/ described a modification of this microprojector for use in making rapid comparative estimates on konimeter samples and other determinations . This report contains information on still another modification named the "midget microprojector " because of its small size .

Sep 1, 1944

By W. E. Miller, John Campbell, W. P. Yant, G. W. Jones

"Because of its interest in accident prevention, the U.S. Bureau of Mines cooperates with city officials and utilities in investigating the causes of explosions in sewers, manholes, and other underground openings and in developing means for preventing such explosions. For several years this Bureau has been cooperating with the Edison Electric Illuminating Co. of Boston and the Boston Consolidated Gas Co. in detecting and eliminating combustibles and physiologically harmful gases in manholes in the city of Boston and adjacent territory.These Bureau of Mines investigations° have shown that combustible gases from the usual sources — leakage from gas—distributing systems and from underground tanks and gasoline wastes — can be located and the dangerous conditions remedied by a well—planned, adequately supervised, systematic, and continuous manhole survey. However, other types of gas, which are termed here ""soil"" gases, also occur in manholes and are more difficult to eliminate because they have no fixed origin and because seasonal and barometric changes affect their production and passage into the manhole space. These gases appear to be produced by bacterial and fermentation or through reactions of entrapped air in the soil. Soil usually abnormally high in carbon dioxide and low in oxygen, and contain varying amounts of methane. They are especially clangorous to men entering manholes because they lack sufficient oxygen to support life. Owing to the difficulty of constructing gastight manholes the most feasible method for eliminating soil gases from manholes is by ventilation. Consequently the Bureau of Mines initiate 4 study of natural ventilation methods for the removal of these gases from manholes and also for taking care of unforeseen accumulations of combustible gases and vapors.The following factors were considered by the Bureau to be important to the natural ventilation of manholes: (1) Relation of area of ventilation opening* to the capacity of the manholes, (2) size and shape of the manhole, (3) design of the ventilation opening (4) and velocity, and (5) weather conditions."

Jun 1, 1936

Provide mine operators with a quick means of identifying the effect of cutting system changes on relative dustiness at the mine face, by developing an interactive computer program for drum-type coal mining machines. Approach A program which simultaneously evaluates machine parameters, coal seam parameters and mine operator-controlled parameters for their effects on relative dustiness has been developed for use on any minicomputer using BASIC computer language. How it works The interactive computer program allows mine operators to make one or more changes at a time to their cutting system to determine how these changes affect relative dustiness of the face. Using this program, mine operators can find the optimum cutting system configuration to minimize dust using their seam conditions and their equipment specifications. The mining machine variables include: number of vane bits, number of gage bits, number of starts, vane wrap, number of end ring lines, rpm, advance rate, ton/min, percentage of time spent cutting per shift, and airflow.

Jan 1, 1986

By Leon E. Esparza

The Bureau of Mines studied 780 acres of the 24,130-acre Sheldon Contiguous Wilderness Study Area (CA-020-1012) in 1985. The study was done at the request of the Bureau of Land Management and authorized under the Federal Land Policy and Management Act (Public Law 94-579, October 21, 1 976) in order to evaluate the mineral resources. The study area is located in Washoe County, NV, about 35 miles northeast of Cedarville, CA. A search of county courthouse records and an examination by foot traverses through and adjacent to the study area did not reveal evidence of any mining or mining exploration activity past or present. In addition, evidence of any form of rock alteration was not observed. Evidence of mineral resources is not apparent. Although basalt, the only rock-type present in the study area, can have some limited industrial applications, sources closer to potential markets probably would preclude rock from this area being economically competitive. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Sheldon Contiguous study area at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys ;s to provide data for President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By Wilbur I. Duvall

The Bureau of Mines presents a theoretical solution for the stresses and displacements in an infinite elastic plate containing a circular hole whose boundary is subjected to applied shear loads over four separated arcs. The results for the applied shear loads can be superimposed on the results for applied radial loads, given in a previous publication, to obtain a complete two-dimensional approximation of the stresses and displacements induced in the rock by tunnel boring machines anchored in a circular tunnel by means of four props. Analysis of the various solutions shows that the tangential tensile stresses induced on the boundary of the circular tunnel by applied radial loads can be minimized in the roof and floor of the tunnel by the application of appropriate shear loads to each of the four props. Thus when planning tunnel boring operations, consideration should be given to the in situ stress field in the rock and the induced stresses in the rock resulting from the applied radial and shear loads produced by the props of the boring machine.

Jan 1, 1968

Provide an accurate, reliable means for determining when a sealed mine or mine section can be safely reopened after a fire. Approach The Bureau of Mines performed a research investigation that resulted in the development of a mathematical formula for deriving a quantity, called RATIO, which can be used to define when a sealed mine or mine section has returned to safe recovery conditions after a fire. Research Results There were two major results from this Bureau research. Over a period of several years, the Bureau of Mines conducted six experiments at its Bruceton Experimental Mine in Pennsylvania. The experiments involved sealing the mine after several tons of piled coal had been allowed to burn continuously for 2 to 3 days. Although gas data obtained during the experiments revealed nothing significant, measured smoke particle levels were found to correlate with the stages of combustion and temperatures of the smoldering coal pile. Moreover, it was found that no smoke particles are produced when high-temperature smoldering exists deep within the mass of the coal pile since the smoke particles are filtered by the coal surrounding the hot region. Smoke is emitted into the mine atmosphere only if combustion is occurring near exposed surfaces. As suggested by these findings, any decision to recover a sealed mine area based primarily upon the absence of smoke particles is not a wise derision.

Jan 1, 1988

By Peter Kovalchik, Ed Kwait, T. Michael Durr

1. BACKGROUND Many research projects on engineering controls for noise reduction in mining were conducted by the former U.S. Bureau of Mines, mostly under contracts from 1972 through 1986.1 Contracts were awarded to determine which mining equipment was responsible for worker noise exposure over the permitted Federal Regulation level of 90 dBA for 8 hours. Dominate noise sources, for each piece of equipment was also determined. The final goal was to develop engineering noise controls for those pieces of equipment and then evaluate them. This was the general approach taken in each research project or contract. This paper deals with what is known about the control of noise from continuous miners, one of the most commonly used underground mining machines. A literature review on continuous miners revealed that the relevant noise sources were divided into four categories: conveyor, cutting head, drive train, and motor noise. The dominate noise sources reported were the conveyor noise and the cutting noise.2 Conveyor noise consists of impacts and scraping at various locations on the conveyor structure. These impacts are associated with discontinuities on the top and bottom decks, impacts between the chain and the tail roller, impacts on the sidewalls at path points of discontinuity under horizontal pivot, and impacts on the flex plate.3 Scraping occurs along the entire length of the chain conveyor. The other dominate source, the cutting of coal, has also been addressed in past research.4, 5, 6 The research presented in this paper only addresses the controls associated with the conveyor. The literature suggests several effective treatments for noise control: retrofitting the chain conveyor with a urethane coating or a urethane sleeve on the chain flights, using a urethane coating or urethane sleeve on the tail roller, constrained layer damping of the decks, and the use of a modified take up plate.7, 8 However, the in-mine durability of these concepts has yet to be proven for the conveyor system. This paper analyzes extensive noise and urethane durability testing on a Joy 14CM9 continuous miner’s conveyor assembly, tail roller, and bottom plate conducted at the Pittsburgh Research Lab facilities. It will also discuss the initial underground testing results for the urethane-coated conveyor flights and tail roller.