Search Documents

By H. E. Powell

A series of alkyl-dithiocarbamic acid amine salts was prepared and tested as collector for slimed lead minerals contained in the waste material from a commercial lead ore concentrator. The reagents, members of a homologous series differing only in the number of alkyl radicals in their structure, were prepared by reacting stoichiometric amounts of primary amines and carbon disulfide in a cold alcohol solution. Subsequent purification was by recrystallization from absolute ethyl alcohol solution. Evaluation was through froth flotation of a mill tailing containing 0.2 percent lead. Results show that maximum recovery (38 percent) was obtained with the reagent containing 8 alkyl radicals, but that maximum rougher concentrate grade (4.8 percent) was obtained with the reagents of intermediate number of radicals.

Jan 1, 1962

By Hugo E. Camargo

Noise Induced Hearing Loss (NIHL) is the most common occupational disease in the U.S. with devastating consequences particularly in the mining industry. A study conducted by the National Institute for Occupational Safety and Health (NIOSH) revealed that 90% of coal miners have hearing impairment by age 50, compared to only 10% of those not exposed to occupational noise. According to the Mine Safety and Health Administration (MSHA), Continuous Mining Machine (CM) operators account for 30% of workers exposed to noise doses exceeding the Permissible Exposure Level (PEL). This number becomes more dramatic considering that 49% of the total national underground coal production is extracted using these machines. In this context, NIOSH is conducting research to identify and control dominant noise sources in CMs. Previous noise source identification was performed using a Brüel &Kjær (B&K) 1.92-m diameter, 42-microphone phased array. These measurements revealed that the impacts from the conveyor chain onto the tail roller, and the impacts from the conveyor chain onto the upper deck are the dominant noise sources at the tail-section of the CM. The objectives of the work presented in this paper were: 1) To rank the noise radiated by the different sections of the conveyor, and 2) to determine the effect of a urethane-coated tail roller on the noise radiated by the tail-section. This test was conducted using an Acoustical and Vibrations Engineering Consultants (AVEC) 3.5-m diameter, 121-microphone phased array. The results from this new test show that a urethane-coated tail roller yields reductions in the tail-section of 2 to 8 dB in Sound Pressure Level in the frequency range of 1 kHz to 5 kHz. However, integration of the acoustic maps shows that the front-section and mid-section of the conveyor also contain dominant noise sources. Therefore, a urethane-coated tail roller in combination with a chain with urethane-coated flights that reduces the noise sources in the front and mid sections of the conveyor is required toyield a significant noise reduction on the CM operator?s overall exposure. These results show the applicability of phased array technology for low frequency noise source identification.

Jan 1, 2008

This U.S. Bureau of Mines (USBM) report conveys the results of an economic analysis of minerals in the West Mojave Management Area (WMMA), including the Desert Tortoise Priority Habitat (DTPH), a proposed special land management area. Undiscovered mineral resources were estimated for the entire WMMA, which totals 8.7 million acres. Known mineral resources were studied for the DTPH, which is an area of 1.2 million acres contained within the WMMA. Federal lands within the WMMA are managed by the Bureau of Land Management (BLM). The WMMA includes Federal, State, and private lands in the western portion of San Bernardino County and the eastern portion of Kern County. The center of the study area is 20 miles northwest of Barstow, California (Figures 1 and 2).

Jan 1, 1993

By C. J. Johnson, C. J. Bise

"As the US coal industry moves into the next century, it is becoming more apparent that the effective application of new technology is the only way it can remain competitive in the energy marketplace. Examples of this emphasis are with us today in such diverse areas as face-ventilation and excavation-equipment applications. The focus of this new technology is directed toward improvements in health and safety, cost control, and productivity.Room-and-pillar mining accounts for approximately 68% of the nations underground coal production; this percentage is not expected to decrease markedly in the near future. As such, this paper analyzes the impacts of the changing technological climate on future room-mid-pillar operations by comparing a base-case section (current) to three scenarios incorporating new or emerging technology. A microcomputer-based comparative analysis will reflect the changes in section production and costs.IntroductionThe ultimate goal for any coal mining company is to effectively use its human and financial resources to maximize its profits through the extraction of its reserves. Although recent workforce reductions in the industry have resulted in a more efficient use of labor and increased productivity, there comes a point in time when further reductions in the numbers of workers in each operating section are impossible with existing equipment. For example, Farinelli and Bise (1987) found that labor cost constituted 62% - 73% of the cost per ton of coal at the mining section, with a minimum crew size. Thereafter, efforts to increase productivity must focus on more efficient mine plans and technology.The fact that an increase in productivity can be realized by reducing non-productive time (change-out and tram time) and converting it to productive time has been known and demonstrated for quite some time. What has not been demonstrated frequently is the quantification of the potential productivity increase of currently emerging technology or ""add-on"" equipment. It is one thing to be able to say that a piece of equipment will make an operation more productive, but it is another thing to be able to quantify the productivity increase that will justify the purchase of the new equipment. Not only is a financial benefit possible in room-and-pillar mining with an increase in productivity, but a decrease in the time necessary to develop a longwall panel can also occur.The purpose of this paper is an analyze the impacts of a changing technological climate on future room-and-pillar operations by comparing a base-case section (current) to several scenarios incorporating emerging technology. To do this, four cases will be developed. A base case, consisting of the typical manner in which continuous-miner sections are currently operating, is compared to three layouts incorporating: (1) flooded-bed scrubbers on radio remote-controlled continuous miners, (2)a continuous miner with side-mounted roofbolters, and (3) a continuous miner with side-mounted roofbolters used in conjunction with a continuous-haulage system."

Jan 1, 1989

By Roy T. Sorensen

This Bureau of Mines report presents the results of a study to rank technologies for extraction of alumina from bottom ash and coal shale. The available literature on composition and availability of coal waste was reviewed, and papers pertinent to alumina extraction are referenced. Types of coal waste were categorized by method of waste generation, coal content (heating value), location, coal type (ash nomenclature), and alkaline earth content. The differences and similarities among the categories of coal waste are summarized as to factors that my affect aluminum extraction, especially factors concerning chemical composition, current production, storage problems, and accumulated tonnage. Data available on physical characteristics and mineralogy did not correlate well with the individual categories of coal waste, and discussion on these two aspects is limited to the differences between coal ash and coal shale.

Jan 1, 1983

Lower the respirable dust exposure of longwall shearer operators by isolating and con-fining the dust cloud near the face. Approach Install conveyor belt screens at various locations on the body of the shearer to contain and hold the dust cloud toward the face side of the machine. This approach provides a cleaner air split in the walkway, over the shearer operators. How It Works On most longwall shearer sections, the dust exposure of the shearer operators is primarily attributable to the machine it-self. The dust cloud originates at the face, and the exposure of the operators depends largely on how quickly this dust spreads into the walkway. Conveyor belt screens placed on the gob side of the body of the machine can reduce the amount of dust which spreads out into the walk-way. In addition, belting may be installed over any open spaces between the shearer under-frame and the panline to prevent conveyor dust from boiling out into the operator's walkway.

Jan 1, 1981

By Elton L. Litchfield

The Bureau of Mines determined minimum energies for direct initiation of expanding gaseous detonation waves in acetylene-oxygen mixtures. Composition limit ranges for the initiation of detonation with fixed energies have been compared to data in the literature. Assuming that the stored electrical energy is completely converted to thermal energy, the agreement between the energy of primary explosive initiators and the energy of electrical discharge initiators was good. Minimum energies for initiation of detonation in the most sensitive composition (40 percent C20 plus 60 percent 0 2) were: 0.64 joule at an initial pressure of 1/4 atmosphere, 5.0X10-2 joule at 1/2 atmos¬phere, and 3.7X10-3 joule at I atmosphere. Fuel concentrations in mixtures initiated to detonation by 4.9X102 joules ranged from 10 to 65 percent C2H2 at 1/4 atmosphere, 10 to 67 percent C2H2 at 1/2 atmosphere, and 9 to 68 percent C2H2 at 1 atmosphere.

Jan 1, 1967

By W. P. Yant, C. E. Traubert

"INTRODUCTION Canister-type gas masks have become an essential part of the equipment of many industries, not only for use in emergencies, but also in performing normal operations of industrial processes and procedures, particularly where ventilation is not practically or economically feasible. They are also used widely for enhancing safety of operations which previous to the development of gas masks had been performed in harmful atmospheres.Since the inception of industrial gas masks the Bureau of Mines has been actively engaged in endeavoring to increase the efficiency and safety of these devices, and this bureau has become a source of advice to manufacturers in producing devices of good quality and to industry in the proper selection and use of these devices. In order to give first-hand information and keep current with the demands and needs of industry it is necessary to perform investi-gations from time to time. This report deals with tests of certain types of commercial gas-mask canisters for protection against mercury vapor.TYPES OF CANISTERS EXAMINEDThis investigation included tests of the following types of canisters:(a) Gas-mask canister filled with 725 c.c. of granular activated charcoal, 8 to 14 mesh, and of a quality used in gas masks which meet the Bureau of Mines approval requirements 4 for protection against organic vapors."

Oct 1, 1932

By G. L. Fitzpatrick

Future applications of seismic holography to "seismically transparent phase objects," such as rock inclusions, fracture zones, liquid-filled cavities, etc., will require techniques to improve the poor image contrast generally characteristic of these objects. Although conventional phase-contrast enhancement techniques could be used, these methods involve additional optical elements such as quarter-wave spatial filters. Owing to the anticipated practical difficulties of properly alining such optical devices and properly locating poorly defined image planes and filter planes, this approach is not considered to be well-suited to the case of seismic holograms and their laser reconstructions. Results similar to those achieved with spatial filters may be obtained without filters by specially processing the seismic hologram data. The new process, which is an extension of Gabor's subtraction holography, achieves an improvement in contrast by an interferometric technique. The process involves adding a ?before" hologram without an object present to a 90° phase-shifted "after" hologram with the object present. Then, the combination is reconstructed with a laser or by computer. Not only is the image contrast improved in such processed holograms, but the images are also phase-contoured. In general, the latter feature is not to be expected when conventional phase-contrast enhancement techniques are employed. The new technique is experimentally verified by examining computer-generated synthetic seismic holograms rather than by examining actual seismic field data. However, results of this study are directly applicable to real seismic data and should prove useful in future applications of seismic holography.

Jan 1, 1973

By James D. Noll, Jon A. Hummer, Aleksandar D. Bugarski, George H. Jr. Schnakenberg, Steven E. Mischler, Larry D. Patts

The National Institute for Occupational Safety and Health conducted a study to determine the effects of selected, state-of-the-art emission control technologies on the ambient concentrations of particulate matter and gases emitted by underground diesel-powered mining equipment. Tests were conducted in an isolated zone of an underground mine to evaluate the effectiveness of alternative fuel formulations, namely, water-fuel emulsions, blended biodiesel fuels, ultralow sulfur diesel fuel, and #1 diesel; and selected exhaust after treatment devices, namely, diesel oxidation catalysts (DOCs), diesel particulate filter (DPF) systems, and filtration systems designed around high-temperature disposable filter elements. The results showed that using a cold-weather and warm-weather water-fuel emulsion formulation reduced mass concentrations of elemental carbon (EC) by about 70% and 85%, respectively. The 20% and 50% soy biodiesel blends reduced EC by 49% and 66%, respectively. The reductions were slightly less pronounced for the 20% and 50% yellow grease biodiesel blends—33% and 56%, respectively. EC concentrations were unaffected by using ultralow sulfur diesel in place of #1 diesel. Use of the reformulated fuels did not substantially alter the concentrations of nitric oxide and carbon monoxide. However, a measurable increase in the nitrogen dioxide (NO2) peak concentration was observed during the biodiesel tests. The ArvinMeritor (AM) fuel-burner DPF system with a palladium-catalyzed DOC reduced EC concentrations by 92%. The diesel filter elements from Donaldson Co., Inc., and Filter Service & Testing Corp. reduced the EC concentration of the mine air by 92% and 70%, respectively. When the palladium-based DOC was used with the AM DPF, it raised the average and peak downstream NO2 concentrations by a factor of three. Tests of the AM DPF system with a platinum-catalyzed DOC and CAP/ETG catalytic particulate oxidizer system had to be terminated because the elevated NO2 concentrations threatened to overexpose the operator. The tests with only a selected DOC also resulted in increased NO2 concentrations in mine air.

Jan 8, 2006

By Michael R. Yenchek

Contacts with energized conductors are a major cause of electrocutions in underground coal mines. Sensitive ground fault interrupters (GFI's) installed on in-mine three-phase ac utilization circuits would probably prevent the majority of these deaths. A sensitive GFI is a protective device that detects and interrupts small deadly ground currents in the milliampere range before those currents can cause ventricular fibrillation in humans. Commercially available three-phase sensitive GFI's have not been specifically designed for application in coal mines. The Bureau of Mines therefore tested three commercial GFI models to determine their worthiness for mine power systems. GFI design and construction, transient immunity, reliability, and time-current characteristics were evaluated in laboratory tests. No commercial device was found suitable for mine use without design modifications. The tests results will serve as a basis for the development of a mineworthy sensitive GFI in ongoing Bureau research.

Jan 1, 1985

By Jerry E. Olson

In 1988, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied additional areas, encompassing 11,303 acres, on the east and west sides of the 20,727-acre Badlands study area (Olson, 1987) in order to evaluate their identified mineral resources. The Badlands study area additions are located in Crook and Deschutes Counties, OR, about 10 and 18 miles east of Bend, OR. No mineral resources were identified. The additional areas studied are underlain by Tertiary-and Quaternary-age basalt flows which are largely covered by a veneer of sand and silt. No mines, prospects, mining claims or mineralized areas occur within or near the Badlands study area additions. Slab lava of marketable grade and quantity was not found in either area. None of the study area is of current interest for geothermal resources, but the eastern study area addition has been leased (1984) for oil and gas.

Jan 1, 1989

Develop and evaluate a mechanical position and heading system (MPHS) that provides information about underground mining machine position and heading to aid in the remote positioning of mining machines during face maneuvers. Background While great improvements have been made in mineworker safety, progressive technology continues to create a safer, better working environment for miners by keeping them away from the dangerous face area. In maintaining such high standards of safety, the Bureau is investigating remote, computer-assisted operation of mining systems for underground, highwall, and surface mining applications. A key component of computer-assisted operation is a guidance system. Since there are no guidance systems on any commercial continuous mining machines, the Bureau itself developed and tested the mechanical position and heading system (MPHS). The MPHS is based on linear position transducers (LPT's), and operates on principles of triangulation to provide machine position (xy coordinate), and orientation in the xy plane (yaw or heading). These data are needed in order to keep the continuous mining machine in proper alignment before and during the cutting cycle. The MPHS theory development is in three parts: characterize the sensors used and their configuration; select and define the navigation reference frames; and derive a closed-form solution for determining the position and beading from sensor information. Application of the MPHS theory required the development of hardware, software, and system interfaces.

Jan 1, 1992

By S. M. Molloy

The postwar demand for insulating material such as mineral wool, in-creased in proportion to the rapid construction of new buildings, placing an enormous burden on the existing mineral-wool industry both in known sources of raw materials and in available plant facilities. In view of the increased demand on the industry, the Bureau of Mines in its Mississippi Valley Experiment Station" Rolla, Mo., undertook an investigation to aid the industry by establishing resources of raw materials through actual laboratory wool-blowing tests and by developing certain methods for evaluating the physical proper-ties of a mineral wool. As material was received from the public, laboratory-evaluation technique had to be developed, the results of which would reflect in the mineral-wool-industry standards. The methods of testing used by the mineral-wool industry, not only would have required a pilot-plant installation capable of producing a large tonnage of mineral wool, but each wool-blowing campaign would have been very expensive and necessitated considerable personnel and equipment. The present laboratory wool-blowing equipment can produce as high as eight wool-blowing campaigns a day. The nature, simplicity, and size of the physical testing equipment permit testing as small a sample of wool as 25 grams and give information as reasonably accurate as in a 40-pound bag of wool. The purpose of this report is to describe the laboratory method of production and the evaluation of the physical properties of small quantities of mineral wool. Considerable work has already been done, and the interest of the public and industry is measured in the number of samples being submitted for testing.

Jan 1, 1948

By N. P. Gallagher

The U.S. Bureau of Mines investigated a hydrothermal sulfidation (HTS) and chloride leaching procedure to recover lead and silver from plumbojarosite. The plumbojarosite, generated during pressure-oxidative leaching of zinc concentrate in a commercial operation, contained, in percent, 25.4 Pb, 18.8 Fe, 1.4 Zn, 29.5 sulfate (S042.), 3.2 elemental sulfur (SO), 13.4 total S, and 7.4 tr oz/st Ag. The HTS was conducted in an autoclave and converted the plumbojarosite into amorphous iron oxide and liberated the Pb and Ag as sulfides (S2) The best operating conditions were 50 g of plumbojarosite and 7 pct So (2.04 g So added) in 500 mL of 2.0-mol/L NH3 at 150° C for 1 h. The sulfidation product contained, in percent, 37 Pb, 28 Fe, 2 S042., 7 total S, and 11.2 tr oz/st Ag. Flotation of the sulfidation product was conducted at pH 3 with 15-pct pulp density and 2.4lb/st of isopropyl xanthate as collector. The flotation concentrate contained 43 pct Pb, 25 pct Fe, and 13 tr oz/st Ag. FeCl3 leaching of the sulfidation product in a resin kettle extracted 98 pct Pb and 97 pct Ag from the sulfidation product, and HCI-Oz leaching in a shaker glass bottle extracted 99 pct Pb and 98 pct Ag. Both leach residues met the Environmental Protection Agency's Toxicity Characteristic Leaching Procedure (EPA-TCLP) standards for nonhazardous wastes. The HTS and chloride leaching procedure is a potentially effective method for detoxification of plumbojarosite-bearing residue from the zinc pressure-leaching circuit.

Jan 1, 1989

By Jr. Sharkey

The Bureau of Mines investigated gases from flash and laser irradiation of Pittsburgh seam (hvab) coal to determine the action of high temperatures on coal. Temperatures in excess of l,000° C were reached with both types of irradiation. Craters about 300 microns in diameter were produced in the coal with millisecond pulses from the laser unit rated at 1.7 joules' output. Gaseous products from laser and flash irradiations in vacuum contained 21 and 8 percent acetylene, respectively. Diacetylene, vinylacetylene, and other products to molecular weight 130 were indicated in the mass spectrum of the gas from the laser study. Single experiments were also conducted in which the laser energy, particle size of the coal, and atmosphere were varied. The results indicated that the distributions of products obtained from the flash and laser irradiations of coal were different from that produced in high-temperature carbonization.

Jan 1, 1966

By Donna L. Anderson

This U.S. Bureau of Mines report discusses the status of a laser-based guidance system to provide position and heading feedback and closed-loop control of tramming maneuvers for a continuous mining machine. The system has been developed and tested at the Bureau, and is now being prepared for underground experiments. The system hardware includes laser scanners, a sensor communication network, and host computer hardware. The system software includes a position and heading computation module and a tram control module. The description of the software includes discussions of laser data acquisition, error compensation methods, position and heading determination, safety checking for continuous miner tramming, and closed-loop tram control. The accuracy of the laser scanner's data, the reliability of the lasers in a dusty environment, and the system's accuracy on tracking the position and heading of the continuous mining machine are shown in the results of experiments performed at the Bureau. Conclusions are stated based on these experimental results, and further work to improve the system performance and prepare for underground testing is discussed.

Jan 1, 1990

By K. C. Dean

A semiquantitative test for the presence and identification of cesium and rubidium in rocks, clays, and mineral waters has been developed by the Bureau of Mines. The test can be used in the field, as a guide for the prospector, geologist, or mining engineer engaged in location or development [w]ork. It comprises two simple spot tests of a solution prepared from the [m]ineral sample. Phosphomolybdic acid, added to a drop of the test solution, [d]etects cesium, rubidium, and potassium in quantities as low as 60 parts per [m]illion. Silicomolybdic acid, added to a second drop of test solution, enables the operator to distinguish between cesium and/or rubidium and potassium. Test procedures, equipment requirements, and limitations of the method are described in this report. Cesium and rubidium were discovered in 1860 and 1861 by Bunsen and Kirchhoff with a spectroscope. The elements usually occur together, particularly in granite and granitic pegmatites. Rubidium does not occur as an essential constituent of any known mineral, yet it is found as a minor element in so many minerals that rubidium is 16th in abundance in the earth's crust. Cesium, which ranks as the 37th most abundant element, is the principal component of pollucite and a minor element in a wide variety of minerals.

Jan 1, 1960

By Alan G. Mayton

A prototype end-cab shuttle car (SC) design has been developed to improve protection and address ergonomic concerns of the SC operator in low coal mines. The new design features an end cab transversely mounted to the SC and equipped with a closed-circuit video system. The end cab was retrofitted to a low-coal SC and evaluated in surface trials at the U.S. Bureau of Mines. During surface trials, test operators evaluated the end-cab SC relative to visibility; cab features-space, seating, controls, and operator position; tramming-inby, outby, and turning corners; and dumping. Trials were conducted using 12 test subjects; 6 were experienced SC operators. Results of the trials were promising. Of the experienced operators, the only operator with low-coal experience gave the new design the highest rating. Four experienced operators rated the end-cab design "better" to "much better" than a standard center-driven, side-cab SC for visibility when tramming, protection from roof and rib hazards, and no change in seat position with direction of travel. This report discusses research to modify a used 21SC JOY SC, retrofit the SC with the Bureau-developed end-cab, and evaluate the retrofitted end-cab SC in surface trials.

Jan 1, 2010

By Thomas E. Marshall, Timothy Batchler, Anthony T. Iannacchione

As the amount of new fractured surfaces or "damaged rock layers" within roof rock increases, the stability of the rock mass decreases. While direct measurements of this phenomenon are not easily made, there is good circumstantial evidence to support this hypothesis. For example, it is common to observe increased cracks or fractures in the immediate mine roof rock before a roof fall. Likewise, roof drill holes placed in areas that later fail often reveal increased numbers and/or separations of fractures within the rock column through time. And finally, the frequency of microseismic activity, representative of rock fracturing, increases before a roof fall. For this study, more than 700 microseismic emissions were collected from two underground limestone mine roof fall areas in southwestern Pennsylvania. Microseismic events were located and magnitudes determined using the moment magnitude technique. Moment magnitude is based on the event seismic moment, which is a measure of the seismic deformation. The amount of new fracture surface length was calculated based on the stored strain energy within the rock prior to fracture. In the two case studies presented, a significant amount of microseismic activity was observed as much as two days before the first signs of failure in the roof fall areas. Additionally, results from this analysis reveal much about the behavior of strata prone to failure and allows for the construction of hazard maps based on microseismic emissions. The potential use of this technique as a means of anticipating roof falls is analyzed and discussed.