Search Documents

By James R. Aggson

This Bureau of Mines report presents a finite element analysis of roof stresses associated with a 4-foot-high by 18-foot-wide underground coal mine entry. This analysis starts with known loading conditions determined in an underground coal mine in West Virginia and is extended to other possible underground loading conditions. The roof failures predicted by the finite element analysis under known loading conditions correlate well with the roof failures observed underground. The most probable failure modes are identified for the various loading conditions considered. Various failure preventive measures are discussed.

Jan 1, 1979

By A. J. Forney

This report summarizes the findings of methods of treating caking coals in a fluid bed to destroy their caking properties. In batch tests it was found that several coals, including those with a free-swelling index greater than 8, could be decaed at temperatures from 400° to 425° C with a fluidizing gas composed of inert gas or steam containing 0.2 percent oxygen and a minimum residence LS,-;,' of 5 minutes. When treatment decreased the free-swelling index from about 8 to 1-1/2 or lower, the resulting treated coal was noncaking. In a continuous unit with continuous feed and discharge of coal, slightly more severe conditions were required to decake the coal. For 18- to 100-mesh coal a temperature of 430° to 440° C and an oxygen-to coal ratio of 0.4 cubic foot of oxygen per pound of coal feed was necessary. Finer mesh sizes required lower oxygen-to-coal ratios. In tests using air only as the fluidizing medium and treatment temperatures well below the softening range, the caking properties of 150- to 200-mesh coal were destroyed in 30 to 40 minutes of residence time at 200° C. Coarser sizes of 18 to 48, 48 to 100, and 100 to 150 mesh required longer residence time.

Jan 1, 1966

By Thomas Fraser

About 24 per cent of our total production of bituminous coal is used in industrial power plants. As regards fuel conservation, therefore, the recovery of unburned fuel from furnace refuse presents interesting possibilities. Considerable attention has been given to this problem in the past, but because of the comparatively low initial cost of power plant fuel in the pre-war period little progress, has been made in this direction in the United States. Because of the higher price of coal in Europe more attention has there been given to the problem. In Germany a process has been developed for separating unburned coal in refuse by using an electromagnetic separator In the United States the use of mechanical stokers enabled low-priced screenings of high ash content to be used, so that even with relatively high percentages of combustible material remaining in the refuse, the loss in money is not excessive. If the price of screenings returns to the pre-war level around $1.00 per ton the process proposed here will probably not be especially interesting, except where the freight charges are very high. However, if the price of delivered coal continues high, such a process should result in considerable saving. The cost of continuous operation of such a refuse treating plant should not exceed 75 cents per ton of fuel recovered.

Jan 1, 1921

By E. B. Kester

In the commercial evaluation of coal tars, a distillation analysis properly carried out is of considerable importance. Close attention must be given to this operation in order to obtain consistent results and to secure the minimum decomposition of the tar compounds, which in many cases are sensitive to undue heat effects. Low-temperature tars in particular contain compounds of this nature, while in the case of tars produced at high temperatures the large proportion of pitch present has an adverse influence during a distillation. If excessive cracking takes place, the composition of the distillate will naturally vary from the normal, with the result that all the analytical criteria subsequently obtained are affected. Where tars, produced over vide ranges of carbonization temperatures are investigated as in the survey of gas, coke, and by-product making properties of American coals nor being conducted at the United States Bureau of Mines Pittsburgh Experiment Station, the method of distillation must necessarily be the sane for all of the tars studied. Also, it must function equally well for both low and high temperature tar, permit accurate fractionation, and reduce adventitious decomposition to a minimum.

Jan 1, 1932

By Frank E. Cash

Accident prevention is an integral part of the operating procedure of the petroleum industry, and refinery officials and employees throughout the United States are exerting concerted effort to reduce the frequency and severity of accidents and are realizing definite results. In other words, the petroleum industry is safety conscious to a much creator decree than most of the other mineral industries. On January l, 1936, there were 11 operating, refineries in Louisiana with a crude-oil capacity of 199,750 barrels per day.4/ This report deals with safety in four of these refineries representing. 72 percent of the refinery capacity of Louisiana.

Jan 1, 1940

By Heine Kenworthy

In 1930 the Shenandoah-Dives Mining Co. near Silverton, Colo., put into operation a newly erected, 300-ton selective flotation plant to mill complex ores from its nearby mine. The operation was a steady producer and was enlarged to treat 600 to 800 tons a day. In 1942 the company opened and started milling an area in the mine containing semioxidized ore. The valuable mineral. Content of this ore was considerably higher than in the straight sulfide ore previously handled alone. The mixture of clean sulfide and semi-oxidized ore was difficult to treat; consequently tailing losses, especially with respect to lead, were high. A. few years later, in order to study the possibilities, of obtaining higher recoveries by a modification of the mill flow sheet, a 1,200-pound sample of mill feed, taken over a period of several days by the company, was submitted to the Mississippi Valley Experiment Station for testing. Although this sample proved to contain more than twice as much lead as the average yearly mill feed, the same problem of recovering the oxidized values were present.

Jan 1, 1948

By C. M. McKinney

This report contains Bureau of Mines routine crude-oil analyses of 20 samples from5 areas on the arctic slope of Alaska. Two samples were condensates from the South Barrow gasfield, Barrow Lakes area. The remaining 18 samples were crude oils from the following areas: Barrow Lakes, 1 seepage sample; Umiat, 10 well samples; Cape Simpson, 1 seepage sample and 3 well samples; Fish Creek, 2 well samples; and Wolf Creek, I well sample. Table 1 summarizes information on the origin of the crude-oil samples, and table 2 summarizes characteristics of the samples. Item numbers in both tables correspond to item numbers of the analyses at the end of this report, and the samples are referred to by these numbers throughout the text.

Jan 1, 1959

By H. R. Shell, John L. Miller, M. V. Denny

In the mica research program conducted by the Bureau of Mines at Norris , Tenn . , many micas other than silicon fluorphlogopite have been synthesized . It has been well established since the initiation of the program that synthetic micas are important materials useful for their superior or unique properties as well as substitutes for natural micas . The possibility of controlling the physical properties of synthetic mica by isomorphic substitution of other ions in the fluorphlogopite lattice further emphasizes the importance of these materials . Accurate measurement and reporting of their properties constitute an essential part of the research program . The study of germanium fluorphlogopite is in keeping with the requirements of a comprehensive study on isomorphic substitution , specifically to identify precisely the material -- chemically , structurally , and optically . The X- ray measurements , including indexed powder and single crystal data , with a description of the methods used to obtain these data , are provided . 5 Earlier work on germanium mica by R. A. Hatch et al . (5) gave an estimate of the cell parameters from X - ray powder data , but no attempt was made to index the diffraction pattern or to determine the space group symmetry . Later work by E. A. Schatz and J. C. Withers (9) listed X- ray and optical measurements , but no attempt was made to index the mica or determine its symmetry . Roth (7) found that germanium dioxide having the a - quartz structure , when heated with equimolar percentages of MgO , CaO , Sr0 , or Ba0 at 1,235 ° C , formed ABO3 -type compounds , e.g. MgGe03 isostructural with enstatite (MgSiO3 ) . Geo₂ also has a rutile - type polymorph with Ge ++ ions in octahedral coordination . Germanium was substituted for silicon in the serpentine structure by Roy and Roy (8 ) using hydrothermal techniques . These authors wrote as follows : "The substitution of Ge + for Si + yielded a magnesia - germania serpentine , formed easily in euhedral hexagonal plates which in some instances were visible in the light microscope . Electron micrographs and the sharp X - ray diffraction patterns confirm a plate - like rather than tubular habit . " It has been shown in this investigation that substitution of germanium for silicon in the mica structure is readily accomplished without radically changing the characteristics of the mica . Substitutions in the mica structure take place in three locations : Tetrahedral , octahedral , and interlayer positions . The tetrahedral positions are normally occupied by Sit or by a combination of Sit with Al +3 the most common combination being 2A1 +3 and 6Si +4 · , The octahedral position , which has six - fold coordination in phlogopite , contains a larger cation such as magnesium . In muscovite it contains only 2A1 ions ; therefore , this mica is considered a dioctahedral mica , whereas phlogopite is considered trioctahedral . +3 The interlayer position has twelve - fold coordination with six oxygen ions from each of two adjacent tetrahedral silica layers . This is the cleavage plane of the mica and commonly contains the largest cation in the mica structure (e.g. potassium) .

Jan 1, 1964

By George A. Savanick

The U.S. Bureau of Mines has patented and transferred to industry an abrasive-enhanced water-jet rock drill. This drill incorporates three novel components: a collimator, jet deflectors for cutting clearance, and an unpressurized swivel, which rotates at 1,000 rpm while passing 20 gpm of an abrasive slurry flowing at 1,000 ft/s. Drilling occurs through the action of a 10,000-psi, 2O-gpm water jet into which is entrained 72 lb/min of abrasives. The pumps, hoses, and fittings are those commonly used in the water-jet-cleaning industry. Only inexpensive, common sandblasting abrasives are used. This drill can cut through hard rocks with moderate-pressure jets; e.g., rocks with a compressive strength of 73,000 psi can be drilled with a 1O,OOO-psi abrasive jet. In addition to drilling holes, the drill can cut deep, narrow kerfs; collar a hole at any angle; drill through rubble; and chamber holes. The development of the abrasive jet drill is a significant advance in the state of the art of hard-rock drilling. The Government of the United States has licensed the abrasive jet drill patent to Weatherford Water Jetting Systems.

Jan 1, 1989

By Ernest L. Corp

Seepage forces computed by a finite-element flow program are combined with gravity forces in an elastic-plastic stress-analysis program to determine the stability of mine-waste slopes. Computer output provides a cross-sectional plot of the dam or embankment showing the safety factors for each element. The combined finite-element program called SEEP-SLOPE was used to analyze several trial embankments and the 1972 Buffalo Creek Dam failure Safety factors computed by the finite-element method (FEM) were compared with those computed by Bishop limiting-equilibrium method. For individual slip circles, there was little correlation between the factors of safety computed by the two methods. Both predict failure, but FEM shows a different mode of failure plus development of potential failure zones not indicated by conventional methods. Besides having a better theoretical basis than the Bishop method, FEM requires no assumptions regarding the location or geometry of the failure surface. As a result, the program will show progressive development of a failure zone, and areas can be pinpointed where remedial measures should be taken. In addition, nonhomogeneous cross sections can be analyzed, and zones of potential piping can be defined.

Jan 1, 1975

By Potts J. D.

Installation of a horizontal air-blocking shelf around the inside perimeter of the surface mining drill deck shroud is proposed to improve dust capture. Without the use of this shelf, a strong Coand? effect airflow pattern results in dust leakage to the environment, especially at the shroud-to-ground interface. Bailing air exits the drill hole and travels along the drill steel to the underside of the table, where it fans out across the bottom of the drill table and continues down the sides of the shroud. This dust-laden bailing air then strikes the ground and fans out under gaps between the shroud and the ground. The proposed shelf prevents dust-laden air from striking the ground by redirecting it toward the center of the enclosure, where it can be captured. Laboratory tests demonstrated that the shelf reduced dust levels outside of the shroud by 81% under operating conditions consisting of a 1.9:1 collector-to-bailing-airflow ratio and a 51-mm (2-in.) gap between the shroud and ground. The shelf was 152-mm (6-in.) wide and was located at a height equal to 2/3 the distance measured from the bottom of the shroud to the bottom of the drill table. The air-blocking shelf was also capable of overcoming the adverse impact of vertical leakage along the shroud seams as long as this leakage was confined to an area below the horizontal plane defined by the shelf location.

Jan 1, 2008

By S. J. Pearce

The need for a simple, very sensitive, and accurate method for the determination of benzene in blood and urine was evident throughout a recent study of chronic benzene (C6H6) poisoning conducted cooperatively by the United States Bureau of Mines, The Barrett Company, and the producers of benzene. A combustion method which will be described in a later publication, end a previously described5/ adaptation of Smyth's method were developed and used during that investigation. The adaptation of Smyth's method gave satisfactory results when dealing with exposure conditions that produced chronic poisoning in a comparatively few days, but it was time-consuming and lacked the accuracy necessary for a study of the absorption, distribution, and fate of benzene in the body during exposure to threshold concentrations of benzene vapor in air. The combustion procedure was satisfactory from the standpoint of sensitivity but was cumbersome, intricate, time-consuming, and required the use of special and somewhat expensive physical and. chemical apparatus. Following the termination of this study of chronic poisoning, possibilities for developing better methods occurred, and these have been investigated by the Bureau of Mines with the aid of Relief Works Division personnel. A microcolorimetric method for the determination of benzene in air has been described recently.6/ The present report deals with the adaptation of this new colorimetric method to the determination

Jan 1, 1936

By J. W. Town

The Bureau of Mines conducted phosphate beneficiation studies to determine the influence of mineralogical and textural features on the recovery of phosphate from select bed and composite samples representing different phosphate rock types of the western Phosphoria Formation. Batch heavy-liquid tests showed that ore grade) pellet size, and type of interstitial material were significant parameters affecting concentrate grade and recovery. Recoveries at acid grade (31.5 percent P2O5) ranged from 98 to 56 percent. Liberation was essentially complete at 28 mesh, and recoveries tended to drop when overgrinding occurred.

Jan 1, 1966

By Travis Q. Lyday

The Other South Pacific Island states extend from Palau, also called Belau, near the Philippines in the west, to French Polynesia in the east. However, a number of countries and territories have been omitted, from this chapter because their mineral production was insignificant to the local economy. These include the French over-seas territories of French Polynesia and Wallis and Futuna Islands; independent states, including Kiribati, Marshall Islands, Micronesia, Palau, Tonga, Tuvalu, and Vanuatu; the New Zealand freely associated state of the Cook Islands, and the New Zealand dependency of Niue. What mineral production existed in these islands was limited to construction materials such as coral reef limestone, crushed stone, and sand and gravel in minor quantities solely for domestic consumption. FIJI The mineral industry of Fiji continued to be dominated by gold, although this sector contributed less than 1 % to the gross domestic product (GDP) of the country. Gold and silver together ranked second in value among the country's exports. Fiji's economy contracted 11% during the 8-month period following the first, on May 14, of two military coups. Although the island nation had been a member of the British Commonwealth of Nations since its independence on October 10, 1970, Fiji's membership terminated with the emergence of the Republic or Fiji on October 15.

Jan 1, 1989

By Floyd G. Anderson

The Federal Bureau of Mines promotes the use of safe and effective dust-collecting devices for rock drilling in coal mines. To insure that such devices are available to the coal-mining industry, the Bureau issues certificates of performance for dust-collecting systems and certificates of approval for dust collectors and rock drills or other mining equipment with integral dust-collecting systems that meet the requirements of an established Schedule.4/ Investigations are conducted under the provisions of the current revision of this Schedule by engineers of the Branch of Health Research. This circular describes briefly the requirements and procedure for obtaining certificates of performance or approval and lists equipment that has been certified as permissible under Schedule 25 or its revisions as of January 31, 1961. The names and addresses of companies to which certificates have been issued are listed alphabetically at the end of this circular.

Jan 1, 1961

By C. R. Nisewanger, F. W. Brown

"The velocity of detonation of an explosive is one of its most important properties, because its performance depends markedly on the rate at which it releases its energy. Fortunately, the velocity of detonation is one of the few properties of an explosive that can be measured precisely. However, the velocity of detonation of an explosive may depend on several factors other than its chemical composition, such as density, physical state, degree of confinement, nature of confinement, and magnitude of initiating impulse. Presumably for an explosive of fixed chemical and physical properties there are certain limiting conditions of confinement and initiation under which the explosive will detonate at a maximum constant and uniform velocity. This velocity is its ""ideal"" velocity of detonation. It is obvious, however, that in order to evaluate performance properties of an explosive in all of its applications it may be necessary to measure its velocity of detonation under a number of conditions in which the velocity of detonation is far from the maximum ""ideal"" velocity.. Under certain-conditions the velocity of detonation may even,be,different at different points in the explosive.It is .relatively simple to determine the velocity of detonation of an explosive under a. standard set of conditions if one is free to use large quantities of the explosive and to form it into a convenient shape. Under these circumstances; one can use a thin column of explosive a meter or more in length. The time required for an explosion to travel the length of the column will not be less,of the order a few ten-thousandths of a second and can be readily and accurately measured .by means of the standard spark chronograph or by photographing the explosion with a rotating-drum camera. However in many applications the explosive charge may be of relatively small dimensions arid may not be in a form convenient for making velocity measurements and often may be enclosed in a case or other confining medium. It may be necessary to determine the velocity of detonation over distances of the order of a few centimeters, in which case the time intervals to be measured will be extremely small. For example, the time required for an explosion to traverse 1 centimeter of tetryl is of the order of 1.5 microseconds.Since no satisfactory method of determining time intervals of the order of magnitude of a few microseconds within an explosive charge was available,, at least not for all conditions that might be encountered in practice, it was necessary to develop a special electronic chronoscope which is capable of measuring time intervals as small as a microsecond with a fair degree of accuracy. This report describes the chronoscope and its application to measurements of velocities of detonation in explosives."

Mar 1, 1946

By L. B. Berger, W. P. Yant, J. B. Littlefield

"INTRODUCTION Hydrogen sulphide (H2S) is one of the most toxic industrial gases and of relatively wide occurrence in industry. Among its common industrial occurrences are, in the production and refining of high-sulphur petroleum, in natural gases, in gypsum and sulphur mining, in rock strata and underground waters (where it is encountered in tunneling and caisson work) in blasting with black powder and in blasting high-sulphide ores with other explosives, in gas manufacture, in the carbonization of coal, and in the manufacture of chemicals.The usual methods of detection, other than by the sense of smell, which is lost in 2 to 15 minutes' exposure to 0.010. to 0.015 percent of this gas, 5/ either are too cumbersome for frequent and rapid analyses or, like the wet lead acetate paper test, afford only qualitative results. A qaantitative determination usually involves the use of solutions, bubblers, flowmeters, standard solutions, burettes, and indicators manipulated by trained technical men. All apparatus and methods in common laboratory use are, in general, unsuitable for the field.The physiological response attending exposure to various Concentrations of hydrogen sulphide in air, is as follows, in percent by volume 6/:0.005 to 0.010: Subacute poisoning - slight symptoms, such as mild conjunctivitis and respiratory-tract irritation after 1-hour exposure."

Jun 1, 1935

By I. L. Feld

This Bureau of Mines report describes the development of a simple method of producing low-phosphorus hematite concentrates from certain submarginal southeastern iron ores. The investigation was undertaken to obtain additional information on the Clinton iron ore outcrops at the southwestern extremity of the Birmingham district of Alabama and to assist in the development of operating techniques that would make it profitable to use the marginal ores of this area for blast-furnace feed. Batch and continuous pilot-plant tests demonstrated that a relatively simple wet scrubbing treatment) followed by a desliming operation to reject argillaceous (clayey) gangue, consistently yielded a marketable granular hematite product. Iron losses were relatively high but could be tolerated in view of the low treatment cost.

Jan 1, 1960

By T. J. Ballard

The Union Copper mine is in the Gold Hill district; Rowan and Cabarrus Counties, N. C. The mine was discovered in 1799 and first worked as a gold mine; but copper was encountered at depth, and the property became an important producer of copper. It is estimated that the mine produced 5,000,000 pounds of copper before operations were discontinued in 1907. As part of the strategic minerals program, the Bureau of Mines conducted a development project on the property from July 1943 to November 1943. Eight diamond-drill holes totaling 2,500 linear feet were drilled to delineate the ore body. Analyses 205 core samples were made. Tabulations of sample analyses and drill-hole logs are presented in this report.

Jan 1, 1948

By F. C. Gibson

An electrical method for the continuous determination of propagation velocities in opaque, confined explosives, and propellants is described. A resistance element imbedded in the reactive material generates electrical signals that are displayed oscillographically and indicate the position and progress of a reactive zone associated with progress of a reactive zone associated with burning or detonation. The method is applicable to both solids and liquids.

Jan 1, 1963