Search Documents

By Ronald D. Hill, Elmore C. Grim

Coal-haul and mine access roads are defined as any road constructed, improved or used by the operator (except public roads) that ends at the pit or bench. These roads constitute approximately 10% of the total area directly disturbed by the surface mining operation(l). In some cases, the land disturbed by haul roads exceeds the area included in the mining operation. Studies (2 and 3) of the U. S. Forest Service in eastern Kentucky show that typical contour mining roads exhibit poor alignment, excessive grades, insufficient strength and durability, and poor drainage. Mine roads in other Appalachian- States, particularly where contour mining is practiced, appear much the same as those in Kentucky. Access roads(4) were also found to be a large source of sediment. It is possible that of the sediment that finds its way into the streams as much (or even more) originates from the haul roads as from the mining operation. Most roads are built as cheaply as possible, and good road-building design and practice are ignored. Maintenance schedules are generally inadequate, and upon completion of mining, haul roads are usually abandoned, with little or no attempt made to bed them down(5 ) . Such roads deteriorate very rapidly (Figure 68). Area mining, which is practiced in flat to gently rolling terrain, presents fewer haul road related environmental problems. These roads through necessity are generally well engineered because of the heavy equipment using them, such as 240 ton (217 metric ton) haul trucks. They must have wide beds, good alignment, and adequate drainage to permit coal haulers to run at top speed during all seasons of the year. Excessive dust can be a public nuisance and a driving hazard, and it is hard on equipment. Calcium chloride and sodium chloride have proven to be effective materials for controlling dust. Two applications during the summer when the ground surface is moist at the rate of 1/2 pound per square yard (.26 kilograms per square meter) (3 1 have been suggested. Th4 most common procedure is to keep the roads wet by using water trucks. Sediment that reaches the streams can be traced to one or more of the following five basic phases of haul-road life:

Jan 1, 1974

By W. M. Traver

As a direct result of the second World War, consumption of nickel in the United States has increased to such an extent that it has been considered timely to investigate undeveloped deposits of the nickel minerals. Funds were made available to the Bureau of lines in 1941 to investigate the extent, occurrence, and quality of nickel ores in the Mirror Harbor area. The Federal Geological Survey mapped' and studied the area during the summer of 1941 and Robert S. Sanford, an engineer of the Bureau of lines, made a preliminary examination in June 1942. A contract for drilling the deposits under the direction of the author was let in July 1942.

Jan 1, 1948

By Richard G. Sandberg

The Bureau of Mins, U.S. Department of the Interior, is investigating a hydrometallurgical procedure to conserve cobalt, nickel, and copper by recovering the metals from the matte byproducts of smelting Missouri lead ores. For want of adequate processing technology the mattes are now either unmarketable or marginally so. The procedure involves leaching with manganese dioxide and sulfuric acid to obtain copper, nickel, cobalt, lead, and manganese sulfates, and elemental sulfur as expressed by the following reaction: MS + MnO2 + 2H2SO4 ? MSO4 + MnS04 + S° + 2H2O, where M = Cu, Ni, Co, and Pb. The leach solutions, containing near theoretical amounts of sulfuric acid and manganese dioxide at 85° to 100° C, convert up to 98 pct of the cobalt, nickel, and copper in the mattes to sulfates in less than 2 hr. As they are formed, the cobalt, nickel, and copper sulfates are dissolved leaving a residue of lead sulfate, lead, sulfur, and gangue. The soluble metals are recovered from the leach solutions by caustic and sulfide precipitation, and the residue returned to the smelter for lead recovery. The manganese can be reclaimed from the spent leach liquor as manganese oxide and recycled to leaching.

Jan 1, 1979

By R. H. Lien

The Bureau of Mines investigated nitrous oxide (N20) stability when used as a solvent for organic removal from metal powder surfaces. Both supercritical and subcritical conditions were studied. This investigation was prompted by the occurrence of a violent reaction when supercritical N20 was being used to deoil a metal powder grinding waste sample that contained 20 to 25 wt pct cutting oil. Tests were conducted to determine the cause of the reaction and to define stability limits. Test data showed that the waste's oil fraction reacted violently with N20 acting as an oxidizer; the metal powder acted as a promoter to reduce the ignition temperature. Although the data were scattered, this temperature appeared to reach a minimum at a certain pressure (dependent on vessel and sample size). The minimum ignition temperature for a 0.64-g sample in a 72-cm3 vessel was 360° C at 200 psig. As the sample size increased, the ignition temperature decreased. For example, when the sample size was increased to 10 g, a reaction occurred at 240° C and 600 psig. Because of the variability of ignition temperature with pressure and sample size, safe operating conditions were not established. Overall, this research showed that extreme caution should be exercised when using N20 in an organic or organic-metal system.

Jan 1, 2011

By F. F. Aplan, J. A. Gutierrez-Rodriguez

"Contact-angle and flotation techniques were used to evaluate the influence of oxygen - both that inherent in the coal and that introduced by ambient temperature, aqueous oxidation - on a wide range of coal ranks. Oxidation was found to decrease the hydrophobicity and floatability of coal; with the effect being minor for coals of high rank but becoming increasingly important as the rank of coal is reduced. As an approximation, oxidation makes a coal behave as if it were one of lower rank. Frother only flotation' of coal· correlates with the captive-bubble contact angle whereas when oil is used as a collector, the flotation appears to follow the pattern shown by the water sessile drop on a fresh, un-reagentized coal surface. Coal recovery lost through oxidation may often be recovered by use of a variety of collectors, of which No. 2 foe! oil is among the best of those reagents tested. A simple alkali-extraction test may be used to estimate the influence of oxidation on coal preparation processes and use.INTRODUCTIONThe hydrophobicity of coal is not only a function of its rank but also of the extent of oxidation of the coal during and subsequent to its formation. Weathering and oxidation processes may proceed in-situ for coal deposits that outcrop near the earth's surface, or the oxidation of the coal particles may occur during mining, stockpiling or processing. Such oxidation, whether it affects the bulk-coal sample or on1y a thin outer layer on the coal surface, can dramatically influence the wettability of the particle and hence such processes as flotation, filtration, flocculation and dispersion.Many of the studies made on the oxidation of coals ·were designed to study its effect on flotation, coking or pyrolysis. The. present study 'is directed exclusively toward the effect of oxidation on the hydrophobicity and floatability of the coal. One of the first studies of the effect of oxidation on coal flotation was that of Sun [l] who found that as oxidation proceeds, coal becomes progressively more hydrophilic. Low-temperature oxidation (100-150°C for 250 h) generally lowered the coal floatability with an oily collector only slightly, but more extensive oxidation (200- 3500 C for 250 h) reduced coal floatability seriously. Sun also found that cationic amines were effective collectors for the oxidized coal which infers that oxidation makes the coal more negative in solution. He attributed the loss of floatability to be due to the accumulation of water-insoluble oxidation products at the coal surface. Gayle et al. [2] found that oxidation adversely affected coal flotation when an aliphatic-alcohol frother was used, though a small amount of oxidation appeared to improve the floatability of some coals using a kerosene-pine oil, collector-frother mixture in pilot-plant testing. Prolonged oxidation adversely affected the flotation recovery of the coals tested, the effect being more pronounced when an alcoholic-type frother only was used. They also noted that the reduction in floatability of lower rank bituminous coals was more affected by oxidation than was that of higher rank bituminous coals."

Jan 1, 1989

By R. L. Grant

An investigation was undertaken by the Bureau of Mines to determine the relationship between freespace and ignition probability for borehole shots. A series of experiments was concluded which covered six freespace conditions for a pemissible explosive in a 3/4-inch borehole and encompassed some 700 shots. The results were analyzed statistically. From the analysis of variance, it was concluded that the freespace means were different and that this conclusion is not impaired by possible differences in the explosives used. Within the limitation of this experiment, a definite relationship was found between the freespace and the ignition probability. Specifically, the incendivity increases with increased freespace up to a maximum; beyond this maximum there is some indication of decreasing incendivity. Further investigations are in progress to establish whether the effects of freespace on ignition probability reported here are applicable to the large test gallery, INTRODUCTION A borehole loaded with an explosive charge is a common feature of the routine gallery tests for determining the permissibility of coal-mine explosives, of Experimental Coal-Mine shots, and of the small steel cannon shots used in connection with certain research programs on the ignition of firedamp (6, 10).6/ The question of the interrelationship of freespace, weight of charge, and ignition probability of the methane-air atmosphere has been raised

Jan 1, 1959

By T. Kessler

As part of a respirable mine-dust research program at the U.S. Bureau of Mines, spark-source mass spectrometry has been used for the semiquantitative determination of trace elements (200 ppm weight or less) in raw coals. In addition, several minor and major elements have been determined using this technique. Sixty-four elements ranging in concentration from 0.01 to 41,000 ppm weight were determined in one anthracite, two mvb, four lvb, and six hvab raw coal samples. The samples represented 10 coal seams located in Pennsylvania, West Virginia, Virginia, Utah, and Colorado.

Jan 1, 1973

By James C. Cawley

This report presents results of recent Bureau of Mines research to establish the probability of spark ignition as a function of current (or voltage, for capacitor circuits) for resistive, inductive, and ca-pacitive circuits in 8.3% methane-air atmospheres. The data presented quantify the explosion hazard created when low-power electronic devices catastrophically fail in an explosive mine atmosphere. Previous litera-ture dealt with levels of probability between 10-3 and 10-4. This re-port extends the probability data to levels as low as 10-7. This study has verified that when the probability of ignition, PI, is plotted on a log-log coordinate system versus the current (or voltage), a continuous, straight-line relationship is formed. An interesting result that can be statistically hypothesized is that at some low level of igniting current the ignition process ceases altogether.

Jan 1, 1988

By F. E. Diebold

The methodology for describing the geochemistry of elements in a coal seam have been developed. This has been applied to the Rosebud Coal Seam, which is an economically important member of the subbituminous coals of the Fort Union Formation in Eastern Montana. The method development has involved a detailed study of two popular techniques for determining the metal geochemistry of coal, namely, whole coal analyses and coal physical fractionation. The mathematically contrived element associations (whole coal analyses technique) and the element concentration trends in the float and sink fractions (physical fractionation technique) are considered to lead to only qualitative conclusions concerning the chemical associations of the elements in coals. Additionally, the processes taking place with the coal during low temperature ashing in an oxygen plasma are experimentally investigated and shown to be of sufficeint extent that the use of such low temperature ash for deciphering element geochemistry is questionable. The method developed in this study is a chemical fractionation that involves the sequential leaching of coal with water, 0.5 N HC1, 3 N HC1, 2 N HNO3, and 48% HF. These leach solutions are shown to selectively dissolve the predominate inorganic phases, sulfates, Ca and Mg carbonates, Fe sulfides and K alumino-silicates and quartz, respectively. These phases were identified with the use of XRD, SEM, EM and leaches (water and 0.3 N HC1) of whole coal and low temperature ash. The incorporation of the anion-exchange step in the leaching scheme was investigated and was observed to warrant further study of such intensity to be, at the time, unuseable. The use of this sequential leaching technique on several coal samples from the same seam generates element concentration trends that can be quantitatively interpreted with respect to the chemical associations of the minor and trace metals in the coal seam. The properties of the various seams of economic importance in the Fort Union Formation in Eastern Montana are compiled and presented. The subsequent conclusion is that there is not a large variation in the properties of these coal seams and that the variations within the Rosebud are within one order of magnitude. The chemical fractionation technique, investigated in this study, was applied to composite tipple samples of the Rosebud seam. Each composite sample represented 76,800 tons of coal. A minimum of 32% of the Ca and Mg are present as separate water soluble sulfates. An excess of the sulfate ion in the water extracts shows the predominating influence of the ion exchange capacity of the organic compounds in the coal. Based upon the CO content of the coal and the HC1 leachate data, 25 to 30% of the alkaline earth elements exist as separate carbonates and the remainder are associated with the organic compounds. The small fraction of the illite that dissolves in the HC1 and HNO3 leachates accounts for the K and Al. Slight dissolution of the pyrite in the HCl solvent occurs, the small amounts of Li and As do not relate to any known phase and Mn is present as a separate carbonate phase. Fe and a significant amount of the As exist in the pyrite that is dissolved in the HNO. Se is equally partitioned between the pyrite and the organic compound~. Most of the trace elements are found in the HF solutions. Li, V, and Cr were interpreted to be associated with the clay minerals (kaolinite and illite). Ni and Pb appear to be present as separate phases and 50% of the Hg is HF soluble but is not chemically related to any known inorganic phase.

Jan 1, 1983

By D. W. Butner

As a part of the Bureau of Mines program for the discovery and development of critical and essential mineral deposits, the Darwin district, Inyo County, Calif., was chosen for investigation as a possible source of, tungsten ore. Two properties were active in the district at the time. One was producing tungsten concentrate and the other was preparing to produce tungsten concentrate as a byproduct in the milling of lead-zinc ore. The objective of the project set up by the Bureau was to investigate promising areas and to sample, thoroughly those which preliminary inspection indicated contained tungsten ore. Work was begun November 17) 1941, and completed January 19, 1942. In the course of the project, 18 localities were inspected and 9 were sampled. The following pages brief the history, note the location, and outline the physical features and geology of the district. The work performed by the Bureau of Mines is described and supplemented with assay maps.

Jan 1, 1949

By D. J. MacDonald

As part of a U.S. Bureau of Mines program seeking improvements to the Bayer process, a typical Jamaican bauxite was heated at temperatures up to 500° C in hydrogen, and its leachability under Bayer process conditions was measured and properties of its leached residue were observed. The objectives were to find ways to decrease the amount of organic carbon in bauxite or in leach liquor derived from it without impairing its leachability, and to improve the leached residue's filterability. Techniques employed included heating bauxite under pressure in an autoclave with hydrogen, and in flowing hydrogen at ambient pressure in a tube furnace. Leaching tests were done with a 600-mL stirred reactor. In some of the leaching tests, ferrous sulfate (FeS04) was introduced before leaching to produce a partially magnetic product. Results showed that exposure to hydrogen at temperatures from 160° to 360° C progressively diminished the bauxite's content of organic carbon and decreased the ratio of organic carbon to aluminum in leach liquor, an improvement that would allow a process using hydrogen-treated bauxite to be operated at a smaller recycle ratio, thereby consuming less energy and allowing greater throughput for a plant of given capacity. The bauxite's leachability was not impaired by high-temperature pretreatments, except at temperatures higher than 280° C. Pretreatments in hydrogen produced black, partially reduced bauxite which upon leaching gave a residue that was attracted to a magnetic field and was amenable to separation from green liquor by a magnetic filtration method.

Jan 1, 2010

By John C. Hartley

Three systems that monitor ventilating fans are described. These electronic monitoring systems automatically perform most of the operations required to conform with the provisions of the Federal Mine Safety Code in the event of fan failure or slowdown.

Jan 1, 1964

By Lawrence W. Sott

This Bureau of Mines report presents several factors that currently enter into the design, manufacture, and testing of windows and lenses used in explosion-proof enclosures. Emphasis is also given to the sealing concepts for lenses. Criteria for adhesives and sealants are suggested based on the survivability of an explosion-proof enclosure as a structure, rather than upon the minimum material properties of its constituents. Procedures for surface preparation of adherends are also discussed.

Jan 1, 1982

By L. H. Kalenowski

The metal lithium, its alloys, and its salts are becoming Increasingly important as industrial materials. Lithium metal, because of its great affinity for elements, such as nitrogen, hydrogen, oxygen, sulfur, phosphorus, carbon, and silicon, has become important for a wide variety of uses, ranging from purifying helium gas by removing the nitrogen to scavenging molten metals of undesirable impurities. The excellent fluxing properties of lithium salts have found increasing use in such applications as fluxes for welding aluminum and in lower melting ceramic glazes and coatings. Lithium chloride is one of the most hygroscopic salts known and is widely used as a dehumidifying agent. .About 17 lithium minerals are known. Four of these have commercial importance: Amblygonite, lepidolite, zinnwaldite, and spodumene. Spodumene is the most important source of lithium and lithium salts at present, but sizable deposits of amblygonite occur in the pegmatite area of the Black Hills of South Dakota. The size and nature of these deposits preclude the, possibility of, any assurance of an adequate supply of amblygonite for an operation processing only this mineral. Frequently spodumene and amblygonite occur associated in pegmatite minerals. Preliminary investigations indicate that a simultaneous recovery of spodumene and amblygonite can be made by froth flotation. A single process for treating spodumene and amblygonite or mixtures of thorn, would make possible more use of amblygonite as a source of lithium and obviate the separation of spodumene and amblygonite when they occur together.

Jan 1, 1952

By F. S. Wartman

Recent changes in metallurgical practice, particularly those in flotation, have altered greatly the functions of the different units of a copper smelter. Gangue minerals are removed from the feed so much more thoroughly that the reverberatory furnace, once virtually a concentrator in which a low-grade ore was concentrated into a rich matte by virtue of the removal of gangue elements as slag, has become very largely a melting furnace in which the rich flotation concentrates are rendered molten so that they may be converted. Moreover, since the proportion of matte to slag in the reverberatory furnace output is greater than it was formerly, the amount of converter slag returned to the reverberatory for cleaning is, in comparison to the amount of slag actually formed in that furnace, also much larger. In some cases, approximately half of the reverberatory dump slag may have originated in the converter. The increase in the proportion of convertor slag to total slag produced has brought about certain consequences not entirely desirable. Converter slags contain a high percentage of iron and therefore are high in specific gravity and are very basic. A considerable guantity of magnetite, both dissolved and suspended as solid crystals, is always a component, The basic nature of the ordinary converter slag and the presence of the suspended magnetite crystals make impossible the reduction of the copper content of the slag below approximately 1 per cent by even the most prelonged settling, and a re-treating process is necessary. At present, general practice in western copper smelters is to return the converter slag molten to the reverberatory furnace. Here dilution by mixing, with slag formed in the reverberatory furnace and reaction with raw sulphides and siliceous materials in the reverberatory feed reduce the magnetite and increase the silicates to the point necessary for a satisfactory dump slag.

Jan 1, 1930

By G. W. Birge

Carbonizing properties of the principal coalbeds of Elk, Clarion, Jefferson, Clearfield, and Centre Counties, Pa,, are described in this Bureau of Mines report, Twenty-six samples, representing the Upper Freeport, Lower Freeport, Upper Kittanning, Middle Kittanning, Lower Kittanning, and Brookville beds, were carbonized by the Bureau of Mines--American Gas Association (BM-AM) method, and yields of products and physical properties of cokes were determined. Expansion or contraction of the majority of the samples was measured in the Bureau of Mines sole-heated oven. Chemical analyses, agglutinating values, and free-swelling indexes are given for all samples. In this area the coals generally are characterized by high sulfur and moderately high ash content, and their suitability for metallurgical use would depend largely upon satisfactory cleaning. The samples from Elk, Clarion, and Jefferson Counties were high-volatile A bituminous In rank, whereas, most samples from Clearfield County and all those from Centre County were of medium-volatile rank. Coals from Clarion County had dry, mineral- matter-free fixed-carbon contents ranging from 56.5 to 60.3 percent and were weakly coking. With the exception of two samples which contained excessive ash, the medium-volatile coals of Clearfield and Centre Counties were strongly coking and, as indicated by sole-oven expansion results, would require blending with lower rank coal to avoid oven damage.

Jan 1, 1963

By G. T. Krempasky

This report covers the installation and evaluation of lb reinforced concrete sets, 6 in each of 3 mines in the Goeur d'Alene mining district, Shoshone County, Idaho, and is the second of a series to determine the feasibility of a more permanent type of mine support. Closure measurements, where applicable, were made periodically of the concrete-set installations and were compared to the initial cross section of the sets. A different method of blocking was used at each test site; at one test site the type of blocking was changed several times during the test. Results from each test site are reported separately. No attempt was made to compare the cost of the concrete installations with the cost of other types of support used in the district. Such an evaluation of permanent types of support would require a longer period of time. At this time, tests are not complete enough to determine the applicability of underground concrete supports. However, results to date tend to confirm the general opinion that precast concrete mine supports could be used to advantage in openings that require support and must have long life, especially where decay of timber is an important factor.

Jan 1, 1963

By O. C. Baptist

This report presents results of an investigation undertaken by the Bureau of Mines to determine the clay content of typical petroleum reservoir sands in Wyoming and the effect of clay content on the permeability behavior of the sands. These results should have significance in determining the feasibility of injecting water into the sands for secondary recovery and in estimating the probable damage incurred by these sands if invaded with filtrates from water-base drilling muds. The results of air-, brine-, and water-permeability determinations are given for reservoir sands in three Wyoming fields. The amounts of materials of "fine silt and clay size" (Wentworth scale) in the sands and the types of clay minerals present, as identified by X-ray diffraction methods, are also presented and discussed.

Jan 1, 1955

By C. J. Thompson

Two sulfur compounds--the 2,2,5-trimethyl- and the 2,2,5,5-tetramethyl derivatives of thiacyclopentane--were identified in Wilmington, Calif., crude oil, using microdesulfurization and gas-liquid chromtography techniques.

Jan 1, 1963

By H. D. Jacobs

The Bureau of Mines undertook a research program to insure an adequate supply of iron raw materials for future iron and steel making needs. A sample was obtained of oxidized taconite from the western Mesabi Range in Minnesota, and the metallurgical response of the taconite to beneficiation by a process that included selective flocculation-desliming-cationic flotation was evaluated. The sample contained 35.3 pct iron and represented approximately 2 billion tons of crude material. Selective flocculation and flotation were evaluated in a pilot plant with a feed rate of 900 Ib/hr. Concentrates averaging 61.7 pet iron and 5.1 pet silica were obtained, with an accompanying iron recovery of 67.2 pet. About 83 pct of the process water requirements were reclaimed from the slime and froth tailing and then recycled.

Jan 1, 1980