Search Documents

By Oliver Bowles

The use of fire as a source of heat was the first step from primitive existence toward modern civilization, and heat has performed functions of inestimable importance throughout the ensuing ages. The first commercial steam engine invented in 1698 demonstrated that heat was an important source of power, and heat has since become the motivating force for railroad trains and steamboats as well as for machines in multitudes of factories. Aside from its function of supplying power, heat is an agent of vast importance in chemical reactions and engineering processes. Because of the high temperature of steam under pressure, losses by radiation from boilers and pipes become excessive unless the radiating surfaces are covered with insulating materials. Insulation is important also for hot-water pipes and many other types of equipment from which heat may radiate. Radiation losses from heated surfaces increase rapidly

Jan 1, 1943

By L. S. Sundae

The Bureau of Mines conducted a series of tests to compare the cutting forces required by radial and point-attack bits when making similar cuts. Three radial and four point-attack bits were tested in two coal mines using the Bureau's in-seam tester to measure coal-cutting forces in situ. Tests were also conducted to investigate the effects of weathering and cleating. The test results show that in each case, at a specific clearance angle, the radial bits required less tangential and much less normal force than the point-attack bits. The resultant of the cutting forces for some types of cut was 50 pct less at mine 1 for radial cuts compared to cuts with the best point-attack bit, and 40 pct less at mine 2. There was some difference between three types of radial bits, but it was not as significant as the difference between each type of point-attack bit. Cutting coal perpendicular to the cleat planes required less cutting and normal force than the same type of cuts parallel to the cleat planes. Test results showed no effect due to weathering on cutting force data. Cutting parallel increased forces only because cuts were made in the rock band.

Jan 1, 1987

By Dougherty. E. Y., S. W. Zoldok, John W. Cole

"INTRODUCTION During its wartime program of exploration for minerals essential to the national economy, the Bureau of Mines was instructed to investigate sources of raw materials used in the manufacture of iron and steel. As a part of this investigation, some work was done on the iron deposits on the Neutral and Aztec claims on Buckhorn Mountain Canogan County, Washington, which was designed chiefly to indicate the nature and behavior of the ore deposits below the surface exposures. Diamond drilling was started in June and completed in July 1945. Preliminary laboratory tests on iron, ore from Buckhorn Mountain were completed during the fall and winter of 1945. This report presents the data obtained from the investigation.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final re¬port. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Apr 1, 1947

By Wallace W. Roepke

The Bureau of Mines determined coal-cutting forces and primary dust generation of four styles of radial gage bits as used on end rings of continuous mining machines. Direct comparisons for reference were made with two widely used conical plumb-bob types having 60' and 90' (nominal) included tip angles. The cutting forces for all of the gage bits were similar to those of the 60°-tip plumb-bob bit. All bits except the RAD-3 gage bit generated similar amounts of primary total dust at shallow cutting, but during deeper cutting, the amounts varied and the gage bits produced as much as 2-1/2 times the dust produced by the 60° bit. This seems atypical since past experience has always shown differences in dust generation at shallow cutting. The specific energy was more like that found previously with other bits, since the values were spread at shallow cutting but became nearly similar at deeper cuts. The 90° bit and the RAD-3 gage bit are not recommended for use except in extremely difficult cutting conditions where dust and forces are of secondary importance. The choice among the remaining four bits can be made on the basis of dust, energy, forces, or cost, as circumstances dictate.

Jan 1, 1983

By Webster S. Anderson

The design, development, and testing of hydraulic props to provide a lightweight, high strength, recoverable unit is described. Modifications in design incorporating threaded components resulted in the development of a lightweight hydraulic prop fabricated from aluminum alloy tubing. This new design facilitates interchange and replacement of component parts, and the physical properties of the material are not changed as they are when welding is required. The new prop is 65,000 pounds and has a maximum load capacity of a lower weight-to-load capacity ratio than the hydraulic props now available.

Jan 1, 1967

By Stephen C. Tadolini, Thomas M. Barczak

Roof support systems, longwall shields in particular, have persistently grown in size and capacity for the past 25 years. Why is this? Is it a good thing or is it unnecessary? What are the consequences of this “bigger-the-better” design philosophy? Rarely do we see a “one size fits all” approach to roof support except when it comes to longwall shields, where the historical trend for new procurements is to simply purchase the highest capacity support you can buy. Does high capacity ensure failures will not occur? The answer is no! The highest capacity tailgate supports are typically the ones that fail the most often. What does this tell us? It tells us that there are fundamental aspects of support design and ground control that we still do not understand or recognize when designing a support system. This paper provides an interesting evaluation of these issues and proposes a different approach to support design that attempts to match the support performance characteristics to the ground behavior. Along the way, some of the old premises of support design will be discarded, and new “controversial” ideas developed. Thinking outside the box never hurt any industry. Mining has made it a common practice.

By Larry L. Anderson

Enormous quantities of organic wastes are produced each year in the United States. The total amount is in excess of 2 billion tons and at least 880 million tons of this is moisture- and ash-free organic material (dry organic solids), representing a potential energy source of significant magnitude that is not being utilized. Bureau of Mines scientists have developed methods for converting these wastes to convenient energy forms. This report itemizes and evaluates for the first time in detail the quantities and sources of moisture- and ash-free organic material contained in manure, urban refuse, industrial wastes, sewage solids, and agricultural wastes in the United States. Furthermore, estimates are presented for amounts of organic wastes collected or concentrated. The potential for fuel, either oil or gas, from both the total organic wastes generated and those collected or concentrated is also estimated.

Jan 1, 1972

By Richard D. Hagni

The character of phosphorous-bearing minerals in the Birmingham red Iron ores and iron-bearing minerals in the Eufaula bauxite deposits in Alabama has been Intensively studied by petrographic, ore microscopic, luminescent microscopic, scanning electron microscopic, electron microprobe, and x-ray diffraction techniques. A total of 15 types of phosphorous-bearing mineral grains have been recognized in Birmingham iron ores by their characteristic sizes, shapes, and distributions. Size measurements, modal analyses, and texture analyses have permitted an estimate of potential liberation of phosphorous from the iron ores by beneficiation to be 27% In areas of previous mining and 60% in areas of current iron reserves. Fine grinding, selective flocculation, and flotation may constitute the best beneficiation technique for future research. Hematite and goethite are the most important iron minerals in Eufaula ferruginous bauxites, but pyrite, marcasite, and siderite are Important iron minerals in some varieties of ferruginous bauxite, and lepidocrocite and ilmenite occur locally in minor quantities. Although simple screening will remove the coarsest iron-bearing grains, research on the utilization of high gradient magnetic separation to reduce the amounts of iron-bearing grains is recommended.

Jan 1, 1981

By C. A. Allen

"The problem of signaling to the hoisting engineer from a moving cage in the shaft has been considered by many mine operators for a number of years. There are several methods in use in different mining districts, and so far as the writer is aware they have been further developed in Utah than in any other state. The latest installations are of interest because they use a very low-voltage circuit for the shaft wires and also because the wiring can be so arranged that the hoist can be stopped from the cage, if so desired.The first installation in Utah was in the shaft of the Centennial-Eureka mine under the management of C. E. Allen. It was placed in operation in the summer of 1899, end has been in continuous and satisfactory operation for 21 years. The arrangement consists or two bare wires down the shaft carrying a current at 60 volts potential, with a device on the cage for making connection between the two wires. This device is simply a short piece of wire which is thoroughly insulated from the cage and is operated by a short lever. Whenever the cage rider wishes to signal the engineer he pulls down the lever, forcing the short wire out against the two bare wires, thus making a circuit which rings the bell in the hoist-room. A similar device was planned in the Grand Central shaft at Mammoth, Utah, but was later abandoned. The cause of failure was reported to be that the shaft was very wet."

Jun 1, 1920

By J. F. Barkley

"Conservation of fuel in boiler-plant practice is one of the major projects of the Bureau of Mines. The large central stations with their corps of trained operators and with refined equipment obtain relatively good efficiency. It is in the many smaller isolated plants that the large fuel wastes are apt to occur. Some operators seem to feel that their responsibility is largely expressed in the phase the phase ""carry the load,"" rather than ""carry the load and carry it efficiently."" Often equipment is not provided to give sufficiently accurate guidance to the operator.In within many such plants, it is interesting to note how frequently the same mistakes occur. The following quite typical example illustrates some of these circumstances and their effort on operation. The boiler plant consisted of two 1000 hp. boilers equipped with multiple retort under-feed stokers. These were horizontal water-tube boilers with horizontal baffling, having a high bridge wall at the back of the stoker. One boilers was used to carry a summer carry a winter load of about 1250 hp. The operators felt that one boiler was not sufficient to carry the winter load. No instruments are available for the operator's use, excepting the steam ores sure gases."

Mar 1, 1925

By Robert Stefanko

Test procedures for evaluating underground coal mine trailing cable splices are formulated. The tests are utilized to evaluate several trailing cable splices. The laboratory results are compared with actual field observations and experience. The results are utilized to define quantitatively the generalized terms of the 1969 Health and Safety Act. Recommended specifications and procedures for testing by MESA Department of Approval and Testing personnel are included. Failure points in splices are detailed and presented for use by a MESA training program and manufacturers attempting to improve product quality.

Jan 1, 1974

By G. S. Scott

The investigation of the causes, behavior, and control of anthracite mine fires, which the Bureau of Mines has been carrying on has yielded several publications directly applicable to mine-fire problems. 3/, 4/, 5/, 6/, 7/, 8/ As a further step in elucidating the causes of heating in certain anthracites subjected to oxidation, reliable information vial needed relative to the actual amount of heat that is liberated when a unit volume of oxygen combines with anthracite at varying temperatures.

Jan 1, 1939

By P. E. King

The U.S. Bureau of Mines is conducting an ongoing research project to better understand the phenomena involved within electric arcs utilized in electric furnace steelmaking. With a better understanding of the physical and electrical characteristics involved, dynamic or predictive control of electric arc furnaces may be possible. A mathematical model is presented, but not solved, and the system of coupled equations is analyzed. Characteristic parameters are used to determine relative importance. In this manner, significant quantities are dermed. The parameters found to contribute little to the system of equations of motion are ignored. A resultant simplified system is identified, and directions for further study are indicated toward control of electric arc furnaces.

Jan 1, 1990

By Federick W. Miller

The Bureau of Mines has investigated the availability of columbium from 19 deposits (3 producers and 16 nonproducers) in 7 market economy countries (MEC?s). Brazil has the largest recoverable columbium resource, posessing approximately 2.39 million metric tons Wmt), or 69 pet of the MEC total (3.47 Mmt). The Western Hemisphere countries of Brazil, Canada and the United States contain 3.14 Mrnt of recoverable columbium or 90 pnt of the MEC total. Columbium recovered as a byproduct of tin mining is not included as part of MEC resources in this study. Currently producing mines are Araxa and Catalao in Brazil, and Niobec in Canada, These three mines have 2.42 Mmt of recoverable resources or approximately 69 pct of the MEC total. It is estimated that these mines, operating at full capacity, could satisfy cumulative MEC demand (based on an annual growth rate of 5.1 pct) for the next 20 yr. The United States is totally dependent upon foreign sources for its columbium supply. The majority of U.S. columbium is imported from Brazil in the form of steelmaking- grade ferrocolumbium. Canada has been the sole source of pyrochlore concentrates since Brazil discontinued exports in 1981. The United States also imports small (but important) quantities of columbium as columbite concentrates from Nigeria and Brazil, as columbite contained in tin slags from Thailand and Malaysia, and as synthetic concentrates from the Federal Republic of Germany.

Jan 1, 1986

By R. D. Currie

Haulage accidents in the anthracite region cause fewer fatal and lost-time accidents per million man-hours than similar accidents in bituminous mines, a fact that may be accounted for in several ways, but primarily because haulage, in a large part of the region, is restricted to haulage crews operating only on the gangways where most of the miners seldom come in contact with movement or handling of cars and locomotives. Generally in underground mines the number of men injured compared with the number killed is greater for haulage than for roof-fall accidents, while the number of men killed by haulage is second only to the number killed by roof falls.

Jan 1, 1939

By W. E. Wallace

Volume-rate-of-flow measurements were made of the flow of mercury through porous samples under conditions of no field, magnetic field transverse to the direction of flow, and transverse magnetic field and electric current to determine if a magnetic method might be potentially useful in the study of pore-size distribution. No change was observed in the flow rate from the application of a magnetic field alone. The application of both field and current produced an electromagnetic pumping action with or against the direction of flow, depending upon the direction of the electric current. This pumping effect was observed to be greater in a rectangular porcelain sample than the calculated value for an equal-Sized open channel.

Jan 1, 1969

By N. E. Hanna

The current Bureau of Mines active list of permissible explosives includes 124 brands. Thirteen are gelatinous and the rest are the more commonly used granular ammonium nitrate type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1965

By N. E. Hanna

The current Bureau of Mines active list of permissible explosives includes 124 brands. Thirteen are gelatinous and the rest are the more commonly used granular ammonium nitrate type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1965

By E. G. Davis

Large-scale ultrafine grinding tests of a coarse kaolin were made using the Bureau of Mines developed attrition grinding process in continuous open-and closed-circuit systems. A 20-inch diameter attrition grinder, designed and constructed at the Tuscaloosa Laboratory, was used. Studies included single- and multiple-stage open-circuit grinding, and also continuous grinding tests in closed-circuit with a 6-inch-diameter solid bowl centrifuge. Clay feed, containing 9.0 percent minus-2-micrometer esd, was used at fates up to 840 pounds per hour. Multistage grinding tests gave better results than single-stage treatment when equivalent clay feed rates were used. Closed-circuit grinding tests yielded ground products containing slightly more minus-2-micrometer-esd clay than the open-circuit grinding when using the same clay feed. Energy consumption was lower in closed-circuit grinding than in batch or open-circuit grinding. A modified two-stage closed-circuit grinding system gave the best grade of product and amount of minus -2-micrometer-esd clay produced per pound of clay feed. The ground product from this test contained 88.5 percent minus-2-micrometer-esd material and electrical energy consumption was 327 kilowatt-hours per ton of minus-2-micrometer-esd material produced.

Jan 1, 1973

By F. F. Aplan

Separation of the slightly soluble minerals (Ksp? 10-10), one from the other is one of the more difficult tasks confronting flotation engineers. This study has focused on means of separating such prominent members of this class as scheelite, fluorite and calcite from one another. Some experimental work has also been done on the minerals magnesite, dolomite and apatite. Carboxylic acid-type collectors are commonly used industrially to float all of these minerals. Thus, the problem at hand is to ascertain means of achieving selectivity between minerals known to respond rather similarly in flotation. Four techniques have been proposed for the separation of minerals of this class from each other: 1. Control of potential determining ions 2. Use of stereo-specific collectors 3. Use of flotation rate differences 4. Use of selective activating and depressing compounds. This study was directed toward a cursory evaluation of each of these techniques, and each was found to be a possible method of achieving selectivity. Stereo-specific collectors -- those whose parking area may closely match the available adsorption site on one mineral but not on another -- are a possible means of achieving selectivity between scheelite, fluorite and calcite. Stereo-hindered carboxylic acid salts and sulfonates all show selectivity between the three minerals tested. Separations also appear to be possible by the controlled use of the lattice ions (e.g., Ca and [W0=4] for scheelite, CaW04), H+, [OH-, C0-3 and HCO=3]; all of them ostensibly potential determining in the systems studied. Flotation rate differences of the minerals as a function of pH under conditions of starvation collector usage also showed promise. Scheelite and fluorite float most rapidly with sodium oleate in slightly acidic (pH 4-7) solutions whereas calcite floats most rapidly near pH 10. Use of Mn++, Pb++, or other heavy metal hydroxy complexes as activators was seen to effect each of the slightly soluble minerals differently. This is in sharp contrast to the oxygen containing, relatively insoluble minerals, where all minerals respond in a similar manner to such activation procedures. Results indicate that all four methods outlined above may potentially be used to achieve flotation separation of the slightly soluble minerals. More extensive research should be undertaken to detail the spcific applicability of each of the procedures and to make a more complete evaluation of the effect of collector type and concentration, mineral type, pH and size effects.

Jan 1, 1983