Search Documents

By S. P. Kinney, P. H. Royster, T. L. Joseph

"The study described in this paper, on the reactions in an iron blast furnace, is part of the investigation being conducted by the Bureau of Mines on combustion of coke and the reduction of iron oxides in the blast furnace. Previous study of the combustion zone of the iron blast furnace, by means of a series of as samples taken through the tuyeres across the hearths of 13 blast furnaces, showed that the combustion of the coke in the blast-furnace hearth is complete at a distance of 32 to 40 inches from the nose of the tuyere, measured horizontally toward the center of the furnace. The results of this previous work are sum¬marized in the curves shown in figure 1, where it will be noted that practically all of the oxygen disappears at a distance of approximately 30 inches from the nose of the tuyere.In order to determine the height at which oxygen is found in a vertical direction above the tuyeres - it had been suggested that the combustion zone turned upward near the tuyere and to obtain comparisons with the samples taken at the Bureau of Mines experimental6 (5-ton) blast-furnace at Minneapolis, the Bureau extended the gas sampling on a commercial furnace to a number of planes between the tuyere level and the stock line. The sampling was conducted on a 300-ton furnace, making foundry iron, operated by the Central Iron and Coal Co., at Holt, Ala. The furnace was smelting Southern red and brown ores and nodules from pyrite sinter. Figure 3 is a vertical section of the furnace showing the six planes sampled."

Apr 1, 1926

By J. W. Miller

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and, from the data developed, to determine: (a) Which coals, either as mined or after beneficiation by conventional preparation, are suitable chemically under present standards for producing metallurgical coke. (b) Which coals require special and more intensive treatment in preparation than is now practiced. (c) Which coals cannot be considered potential sources of metallurgical coke, regardless of preparation. This report is one in a county series and describes the preparation characteristics of the coals of Logan County, W. Va. According to present-day standards for metallurgical coal, many believe that the sulfur content of the coal should not exceed 1.25 percent? Coal with more than this amount has been used for making metallurgical coke, especially when blended with coal containing less sulfur. In this series of reports 1.25 percent sulfur is used as a gage to determine whether or not a coal will be suited for metallurgical coke.

Jan 1, 1957

By C. H. Fisher, M. L. Fein, A. Eisner, G. C. Sprunk, Loyal Clarke, H. H. Storch

"The large reserves of low-rank coals in the western United States are at a disadvantage in competing with the more mature but less plentiful eastern coals, which are nearer important markets and are more suitable for combustion and coke production. However, low-rank coals generally are amenable to hydrogenation, and the western coals might become an important source of liquid fuels and organic chemicals when petroleum is less plentiful.In view of these facts an the tremendous quantities available, further information on the western coals clearly desirable. The purpose of the work described in this paper was to study the hydrogenation characteristics of some of the low-rank western coals in discontinuous converters. The data obtained in this manner, which are inadequate for predicting the suitability of coals for large-scale continuous hydrogenation, were used as a basis for selecting samples for further study in the Bureau's experimental coal-hydrogenation plant (26, 35). 8/ Because of the general importance of the western coals and recently demonstrated relation between coal hydrogenation and petrograghy (14, 15, 16), the proportions of anthraxylon, (vitrain), translucent attritus, and opaque matter were determined. In some instances samples of anthraxylon were isolated and hydrogenated separately so that their properties might be compared with those of the entire coal. The samples studied include peat, brown coal, lignite, sub-bituminous coals, and low-rank bituminous coals."

Mar 1, 1940

By L. A. Readdy

Pilot Hole "X" was drilled to test the formations through which the ventilation shaft for the proposed U.S.B.M. demonstration oil shale mine would be drilled. The geologic formations encountered in this hole are discussed. Correlation of the geologic horizons encountered in this hole with those encountered in nearby drill holes was accomplished by the use of geophysical logs. Data on the geophysical interpretations are provided. The anticipated geotechnical characteristics of the geologic units encountered in Pilot Hole "X" are described.

Jan 1, 1977

By R. R. Sayers

"An important, function of the U.S. Bureau of Mines is to instruct miners in first aid, and as a means of promoting interest in it first-aid contests are held under the auspices of the Bureau, usually in coop; ration with other interested organizations, especially the American Red Cross, the National Safety Council and various operators' and Miners' associations. It was early found that the method of judging first-aid meets is one of the most vital factors in determining the degree of success of the meet.It may be safely stated that there is no method for the judging of first-aid contests that has proved ideal. A method that would give the most uniform judging would necessitate the rating of each team by the same judge or committee of judges and, in order that a judge may rate a team satisfactorily, he should see that team perform several events and average the ratings. Such a procedure is not practicable where there are many terms entered in the contest, as it would prolong the meet indefinitely. To overcome this objection the method has been tried of assigning separate judges to each team but this brings in a new factor the individuality of the various judges, some of whom rate closely, others loosely. The next development was to average the judging by having the judges rate different teams for each event. This would seem to solve the problem out it has been found, after using the method over a wide area for a considerable period of time, that the differences in the judging are too marked to be at all satisfactory. The next development was to appoint a committee of chief judges three to five in number especially trained and experienced, to aid the individual judges in rating the teams. This method has proved satisfactory at small meets but, as committee must review the work of each judge on each event, it has not been deemed feasible for a large meet."

Nov 1, 1920

By Irving Hartmann

[The explosability of coal dusts has been the subject of many investigations studies have been conducted in laboratories, in galleries and in coal faire; of several countries to obtain information on the causes, development, and prevention of mine explosions. Early laboratory experiments on it American colas dealt with pressures developed in test bomb by explosions of dust clouds and with, the effects of gas in the dust atmosphere.5/ Later, the emphasis shafted to evaluation of the relative fleet flammability and the ignition temperatures of coal dusts.6/ Much worthwhile effort was devoted to the development of Laboratory apparatus and test procedures that gave good correlation with large-scale explosion tests in the Experimental cost mine. In recent years a number of special problems were studied, mostly with bituminous Pittsburgh coal dust]

Jan 1, 1954

By Frank G. Miller

Controlling natural-water drives to effect efficient and economic production of petroleum, through wells, from reservoir sands and rocks is a problem of major importance in the oil-producing industry. Water-drive fields are characterized by large quantities of mobile water under high pressure immediately below the oil in the flanks or extraneous parts of reservoir formations, Hence, the water, which is in fluid connection with the oil and a source of a large proportion of the energy available for moving it, advances up-structure to replace it. This phenomenon of water moving crestward into the oil-bearing parts of the reservoir and replacing oil is termed edgewater encroachment. The mechanism by which oil is flushed out and continually replaced by water as the hydocarbon content of the field is depleted must be understood if natural-water drives arc to be used successfully to, induce efficient recovery of oil from its reservoir rocks. Until recently, the function of water in the production of oil has been somewhat obscure and was not given the consideration it deserved in early petroleum production-research programs because of the greater importance associated with and the effort devoted to investigations concerning the relations of natural gas to production of oil. Thus, with virtually no fundamental information at hand, it is not surprising that at first edgewater was considered a necessary evil, and the manner in which it was dealt with depended largely on the experience of the operators. During the intervening years, however, practical information on encroachment of edgewater in oil sands has been widely disseminated as a result of studies of oil-field depletion, and many theories pertaining to petroleum-reservoir energy and performance have been advanced; these theories necessarily included consideration of edgewater as an integral -art of the reservoir fluids and a source of energy for propelling hydrocarbon fluids through the reservoir and to the surface of the ground.

Jan 1, 1941

By Ross. C. Barkley

A computer program has been written to simulate ground vibrations induced by multiple-hole surface blasts. The program is an inexpensive and relatively easy to use tool for predicting the principal blast vibration characteristics that determine damage and annoyance potential: peak particle velocity, frequency content and pulse duration. The program generates a complete ground motion history by superposing, at any surface position, the vibrations induced by each individual explosives charge. It requires specification of (hence allows accounting for) the blast geometry, initiation sequence (including random delays), position with respect to blast, pulse characteristics induced by each charge, and propagation laws. A methodology is outlined to determine the necessary variables either on the basis of site investigations (e.g. velocity, attenuation, pulse), or by backcalculation from measured blast vibration records. The latter procedure has been applied to blasts from two coal strip mines. Main difficulties are backcalculating individual pulses, propagation (especially dispersion) parameters and delays. A normal distribution of delays, based on published results, has been shown to influence the results and the response of a single degree of freedom structure significantly. Broadening of the wave types included and additional verifications with field results are required.

Jan 1, 1983

By John C. Machisak

THIS INFORMATION CIRCULAR contains 1956 and 1957 injury experience and employment data for metal mines in the United States and Alaska. Unlike previous publications, this report covers only metal mining and contains statistical data on injuries and employment pertinent to metal mines and mills reporting voluntarily to the Bureau of Mines on an annual basis. Injury and employment data for the nonmetal industries, which from 1911 through 1955 were published in the same series as the metal industries, for the first time will be published separately as an information circular entitled "Injury Experience in the Nonmetal Industries, 1956 and 1957." The Bureau of Mines is authorized to make requests for injury and employment data, and the information submitted by operators of metal mines and mills is a step forward in promoting safety in the metal-mining industry. Every effort has been made to make this coverage as complete as possible.

Jan 1, 1960

By Constantine C. Popoff

The Hermada antimony deposit is in the Sewtooth Range in southwestern Idaho, about 77 miles by road northeast of Boise. Stibnite mineralization occurs over an area one mile wide from west to east and two miles long. It is locally referred to as the Swanholm district. In 1947 high- grade stibnite ore was discovered on the East Fork of Swanholm Creek. Since then, ore in commercial quantity has been produced by the Hermada Mining Co. The total output for 1947-50 was about 5,000 tons of ore, containing 640 short tons of antimony metal.

Jan 1, 1953

By H. B. Brunot, L. C. IlsLey, E. J. Gleim

"INTRODUCTION To supply inspectors, safety engineers, and others with detailed information as to the safety features of the various electrically operated machines that have been approved as permissible by the Bureau of Mines, three bulletins and five reports of investigations have been published dealing with the various classes of approved machines:Bull. 313, Permissible Storage-Battery Locomotives and Power Trucks.Bull, 343, Permissible Coal-Handling Equipment Approved from January 1926 to December 1930, inclusive.Bull. 382, Permissible Coal-Cutting Equipment Approved Prior to July 1, 1932.Rep. of Investigations 3309, Permissible Electrically Operated. Air Compressors.Rep. of Investigations 3326, Permissible Electrically Operated Room Hoists.Rep. of Investigations 3345, Permissible Electrically Operated Rock-Dust Distributors.Rep. of Investigations 3363, Permissible Electrically Operated Hand-Held Coal Drills.Rep. of Investigations 3391, Permissible Electrically Operated Post Drills and Drilling Machines.The present paper gives similar information relative to the mine pumps approved before October 1, 1939."

Mar 1, 1940

By Gilbert L. Forst

The objective of this program is to identify and evaluate superior, lightweight substitutes for selected coal mine roof support concepts such as crossbars, posts, and crib blocks. Engineering analysis and concept design identified, through tradeoff studies, that some materials are promising, from a technical standpoint, as support substitutes: E-glass reinforced polyester resin, high strength low alloy steel, aluminum, and very high early strength (VHE) cement. An economic analysis indicates that none of the lightweight substitutes are economically competitive with wood on an initial cost basis; however, in terms of life cycle costs based on current dollars, the high strength low alloy steel appears competitive for crossbars, and the VHE cement and E-glass/resin appear competitive for posts.

Jan 1, 1978

By S. M. Runke

[The coarse-grained granitic pegmatities of the United States have long been a source of many important industrial minerals, because of this, they have been studied intensively by geologists, mining engineers, end metallurgists. These studies have amassed a rather astounding array of published and unpublished information. Correlation of geological studies between individual pegmatites, as well as between major districts, has brought fort come semblance of order to the knowledge of the structure and mineralogical composition of those highly complex and irregular deposits, making it possible to classify certain pegmatites and pegmatitic zones into several grouts of associated minerals, based upon the presence or absence of the minor minerals of beryllium and lithium. This classification or trouping of minerals, with the methods that have been developed for recovering certain of these minerals, possible a systematic approach to the winning of many of the industrially important minerals from pegmatite rock by u single integrated process.]

Jan 1, 1952

By James J. Snodgrass

The Bureau of Mines designed and constructed a series of calibration models for geophysical borehole logging. A nominal hole diameter of 3 inches was selected as representative of typical core holes drilled for mining and engineering purposes, although additional hole diameters of 2, 5, and 8 inches are provided in one of the models for determination of empirical correction factors for variations in hole diameter. The physical properties of the models were determined by laboratory analyses of drill core samples and evaluated statistically for reliability. This report outlines the location of the models, elements of design and construction, and results of the laboratory tests. The models are available at the Denver Federal Center, Denver, Colo., for use by Government agencies and private industry to calibrate logging equipment for measurements of density, sonic velocity, magnetic susceptibility, and electrical resistivity.

Jan 1, 1976

By Sabri Ergun

NEW theoretical data are presented for the intensity of X-rays diffracted from randomly oriented aromatic and alicyclic molecules and diamondlike structures such as are found in coals, cokes, and carbonaceous materials. Data have been computed using the Debye interference function. Computations for the smaller molecules have been made with the Univac 1204 computer: those for large structures, with either the IBM 704 or Bendix G-20 computer. A brief theoretical introduction of the Dobye interference function is given, and an outline is made of the treatment of experimental data so that the experimental interference function can be obtained.

Jan 1, 1965

By S. K. Ash

In arriving at economic losses in coal mining due to accidents, a statistician is confronted with many difficulties on account of the lack of information relative to nonfatal accidents. For comparative purposes the ex¬ perience of those countries, States, or companies that keep complete records can be drawn upon and an extimate can be arrived at whereby one State can be compared with another, or one mine compared with another in the same district. Such a comparison for the United States has been compiled by the United States Bureau of Mines. It will be observed in Table 1 that the cost per ton for accidents in the State of Washington for the year 1927 is higher than for any other State, with the exception of Georgia and North Carolina, with a small combined tonnage of 130,089 tons. (The figures for coal production in Table 1 are taken from Bulletin 319, 1930, of the United States Bureau of Mines.) The reasons why the cost of accidents in Washington might be higher than the average are on account of physical conditions such as steep pitches, faults, igneous intrusions, highly explosive coal-dust, extremely friable coals, presence of gravel and water, very gassy coal beds, rugged topographic conditions, inherently bad roof and floor, thick beds, and heavy cover. The nature of the coal beds requires the use of preparation machinery. The mines are often deep, and topographic conditions are such that long and fast haul¬ age becomes necessary. All of these factors not only tend to cause high cost of production, which is manifested largely in a. lower than average daily pro¬ duction, per man, but..they.also affect to some degree a tendency toward a higher than average cost for accidents.

Nov 1, 1931

By Jerry J. Gray

The utilization of secondary titanium was determined in a study by the Bureau of Mines, and a 10-year statistical table showing supply and distribution patterns is presented in this report. Over the total 10-year period, estimated scrap consumption is larger than estimated scrap supply. Trends from the estimated data indicate that titanium is in short supply and probably will continue to be in the future. Because of higher processing costs for recycle scrap, scrap will tend to migrate to the steel and aluminum industries and to ferrotitanium production and exports. Nonrecoverable losses of titanium metal during processing was determined to be a potential area for research.

Jan 1, 1971

By F. A. Rutledge

"The chromite deposits of Red Mountain, 10,miles southeast of Seldovia, Alaska, are in an intrusive of ultramafic rocks. The earliest reference to the deposits was made by U.S. Grant3/; J.B. Mertic, Jr. 4/ made a brief examination in 1917; and A.C. Gill5/ spent 7 weeks studying the ore bodies and geology of the region in 1918. The Federal Geological Survey had a field party in the region from July until September 1940 and the Red Mountain area was mapped and geological data were assembled by P.W. Guild.6/A preliminary investigation of the Kenai chromite deposits was made in July 1941 by R. S. Sanford,7/district engineer of the Bureau of Mines, accompanied by P. W. Guild, assistant geologist of the Geologi¬cal Survey. This was followed by surface sampling and core drilling, which were completed in September 1942 under the direction of John W. Cole,8 associate engineer of the Bureau of Mines. G. O. Gates, associate geologist, and A, B. Unkelsbay, junior geologist, of the Geological Survey, logged cores and interpreted geologic features revealed by Bureau of Mines drilling and trenching.9/J. C. Roehm, associate engineer of the Territorial Department of Mines; examined the Red Mountain area in august 1941.10/Additional exploration of other deposits in. the Red Mountain area was completed during the summer of 194. Work consisted of surface sampling, core drilling, and mapping. G. O. Gates, associate geologist of the Geological Survey, spent 4 days in August investigating results of the Bureau of Mines program.Throughout the exploratory work conducted by the Bureau of Mines the cooperation of Red Mountain Chromite, Inc., and especially of John Blodgett, Jr., and Collis 2, Druley, president and superintendent, respectively, was greatly appreciated. Use of their camp in the Windy River cirque and shops at Kasitsna Bay facilitated the Bureau of Mines program."

Apr 1, 1946

By L. A. Neumeier

The Bureau of Mines evaluated the properties and anisotropy in properties of rolled Zn-Ti and Zn-1.0 wt pct Cu-Ti alloys containing up to 0.36 wt pct Ti. Finish rolling was at varied temperatures to total reductions as high as 92 pct. Alloy properties are very sensitive to various combinations of composition, rolling temperature, and reduction. Properly rolled Zn-1.0 Cu-Ti alloys are superior in strength to Zn-Ti alloys. Conditions are described that lead to best tensile properties. Creep resistance for Zn-Ti alloys decreases with increased rolling temperature when finish rolled to 92-pct total reduction: but not when finish rolled to 33- or 67-pct reduction. Creep resistance for 7n-1.0 Cu-Ti alloys improves with increased rolling temperature to about 480° F. Heavily cold-rolled Zn-1.0 Cu-Ti alloys have fine grain sizes and poor hardness, tensile, and creep properties, but high ductility. Thermal expansivity is markedly affected by the copper addition. Data show the anisotropy of tensile, creep, and thermal expansivity properties. Large idiomorphic crystallites of TiZn15 appear in both Zn-Ti and Zn-Cu-Ti alloys when more than about 0.2 pct Ti is present. A new Zn-Cu-Ti intermediate phase was also identified. Empirical equations are presented relating creep rates with major process variables.

Jan 1, 1971

By A. J. Kraemer

This report is one of a series dealing with oil-shale-operations in foreign countries visited and studied by Bureau of Mines oil-shale technologists within the past 4 years. Many oil-shale deposits have been discovered in Brazil and studied with various degrees of thoroughness. In this report the major emphasis is upon the oil-shale concessions of Companhia Nacional de Oleos Mineraes, in the River Valley of the State of Sao Paulo, because this oil-shale deposit is one of the most promising in Brazil for large-scale utilization for the manufacture of liquid fuels and other products of oil-shale processing, and because the opportunity was afforded to examine the concession area and to study mining, retorting, and. refining operations on these shales. Results of detailed analyses at the Oil Shale Research and Development Laboratories of the United States Bureau of Mines, Laramie, Wyo., are reported, Analyses and other date dealing with other oil-shale deposits in Brazil have been compiled from many sources. As many data have been reported as could be correlated to indicate the range of variation of the several types of shale end similar material. The oil-shale deposits in Brazil differ widely in size, richness of the shale, and of the oil. Some deposits are situate& more favorably for exploitation than others.

Jan 1, 1950