Search Documents

By E. M. J. Alenius

This paper describing the mining practices at the United Verde open-pit mine at Jerome, Ariz., is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts in the United States. The purpose of this paper is to present the methods used in developing and operating the mine, and to discuss the problems encountered.

Jan 1, 1930

By Walter W. Kaufman

This report summarizes a study conducted to determine the state of the art of various rock removal systems and their capabilities. The objective of the study was to determine if currently manufactured equipment can adequately accomplish rock removal in surface mine reclamation applications. Evaluations of state reclamation regulations, with regard to topsoil rock content, were made to determine the rock removal requirements. The major categories of equipment studied are rock pickers and rock rakes. The impact of rock removal implementation on the reclamation operations is discussed in detail.

Jan 1, 1979

By Michael S. Miller

During U.S. Bureau of mines mineral investigations, in 1981 and 1983, no mines, prospects, or mineral resources were identified in the Little Sand Spring Wilderness Study Area (WSA). Placer gold values in near-surface samples from alluvial fans within or near the WSA contained no more than 66 cents gold per cu yd, at $400 per troy ounce gold price. Sand and gravel and carbonate rocks occur in large quantities, but transportation costs to distant markets preclude their classification as resources. Nitrogen, lithium, clay, pumice, perlite, aragonite, and agate occurrences in the WSA are small or low-grade. The Silvia Mine, adjacent to the WSA contains gold-, silver-, copper-, and lead-bearing shear zones which strike toward the WSA. INTRODUCTION The Little Sand Spring WSA, encompassing 33,500 acres, is approximately 56 mi east of Big Pine, California, by paved and graded dirt roads (fl;. 1). Elevations range from 2,600 ft in Death Valley Wash to 5,600 ft along the California-Nevada boundary. The nearest permanent facilities are at Grapevine Ranger station and Scotty's Castle (Death Valley Ranch), about 9 and 11 mi, respectively, south in Death Valley National Monument.

Jan 1, 1983

There has been a substantial increase in the use of rubber-tired front-end loaders in the mining industry in recent years. Concurrent with this increased usage, in the period of 1966 to 1970, there were at least 74 mining industry fatalities involving front-end loaders, or (on the average) in excess of one fatality per month. When the usage of front-end loaders by the construction industry and other industries, organizations, and agencies, such as the Government (i.e., Department of Defense), along with the uncounted numbers of serious, but non-fatal accidents, are included in the picture, the safety record for front-end loaders, of necessity, becomes a serious subject for study. There is an urgent need for attempts to be made to eliminate or reduce the number of safety hazards; to decrease the confusing diversity of controls designs found on present front-end loaders; to improve the maintenance and operating procedures; to formulate better personnel policies; to increase management and official awareness of the extent of the problem, in both industry and the Government; etc.; in order to decrease the number of accidents. Part of the problem may be traced to the fact that the operator of a front-end loader is frequently designated a "heavy equipment operator." This implies that he is automatically qualified to operate any model, of any manufacturer's, wheeled or tracked, front-end loader as well as many other types and classes of heavy equipment. Contrary to automotive practice, the complement of primary operating and emergency controls varies widely from model to model, as well as from manufacturer to manufacturer. Not only are certain controls present on one front-end loader model and absent on others, but there are significant differences in the modes of control operation, in the functions performed by superficially similar controls, in the location of the various controls, etc.

Jan 1, 1973

By M. M. Wong

Beryllium possesses attractive properties for use in the nuclear and space fields. Since fused-salt electrorefining can be employed to produce this metal in high-purity form from low-grade or scrap metals, the Bureau of Mines investigated electrorefining of beryllium in electrolytes composed of a LiC1-KC1 eutectic mixture plus varying amounts of BeC12. Results showed a 99- percent or better reduction of oxygen and magnesium and a substantial reduction of other minor metallic impurities. Extremely pure beryllium metal was produced. Operating variables, including BeCl2 concentration in the bath (3.5 to 16.5 mole-percent), temperature of operation (450° to 550° C.), and cathode current density (45 to 770 a,/sq, ft.), were studied; their effects on the deposition of metal, working condition of the bath, and purity of the refined metal are discussed. The safety precautions used in handling beryllium in the laboratory are also described.

Jan 1, 1962

By Edmond Chin

The land mass of the Asia and Pacific region comprises 11 million square miles or about 15% of the total Earth's land area. The bulk of the region is contained on the Asian continental land mass. Australia, the world's largest island or the world's smallest continent, alone is almost as large as the continental United States. The islands of New Zealand, New Guinea, Borneo, Sumatra, and Honshu are among the largest in the world. Collectively, they constitute a land area of 1.1 million square miles or an area about one-fourth the size of the United States. The countries in the Asia and Pacific region represent some of the most vibrant economies in the world. Japan is undisputed as one of the world's leaders in manufacturing and commerce. Hong Kong and Singapore are significant both as entrepôt and banking centers. The economies of Australia, the Republic of Korea, and Taiwan compare favorably to the level of the industrialized countries in western Europe. Indonesia, Malaysia, the Philippines, and Thailand have maintained strong economic growth during the past two decades. All these countries in the Asia and Pacific region collectively constitute a significant bloc as to raw materials production and consumption, as to manufacturing, and as to world trade.

Jan 1, 1992

By Russell Levens

A strategy for prioritizing mining health and safety research by evaluating the potential for risk reduction through interventions is proposed. Mining has one of the highest incidence rates of injury and disease found in major industries. The main premise of this paper is that often the best opportunities to reduce these rates are not revealed by retrospective analysis of injury and illness data. Instead, a proactive approach is needed that accounts for risks to specific hazards that can be abated by engineering or behavioral interventions. The process proposed here begins with development of prospective interventions. The degree of reduction in risk to be expected from an intervention then is determined from statistics on the mining worker population, the expected degree of success of the intervention, and the expected change in the severity of injuries resulting from the intervention. Three disparate mining health and safety concerns are presented to demonstrate common problems in assessing risks of injury and illness and describe additional data needs. Information on events preceding injuries and illnesses and more detailed demographic data on the mining work force are needed to analyze injury and illness data more precisely. Detailed information on exposure to specific hazards is necessary to evaluate the potential for an intervention to reduce risk of injury or illness.

By Arthur M. Hartstein

The Federal Bureau of Mines, under a contract with Ultrasystems, Inc., investigated the thermal oxidative degradation characteristics of conveyor belts used in underground mines. This included the determination of smoke evolution, glow characteristics, char yields, and the identification and quantification of all volatile decomposition products in the form of gram of specific product formed per gram of belt sample tested. In addition to these investigations, degradation studies were conducted on some pure ingredients used in conveyor-belt formulations. Three basic classes of belts were investigated: neoprene, polyvinyl chloride, and styrene-butadiene rubber compositions. The studies indicate that styrene-butadiene-based belts exhibit good flame resistance and are the least hazardous in regard to overall formation of toxic decomposition products. Under this program, thermogravimetric analysis was definitely established as a method of material differentiation.

Jan 1, 1976

By James D. Noll, M. Eileen Birch

A monitoring method for diesel particulate matter was published as Method 5040 by the National Institute for Occupational Safety and Health (NIOSH). Organic and elemental carbon are determined by the method, but elemental carbon (EC) is a better exposure measure. The US Mine Safety and Health Administration (MSHA) proposed use of NIOSH 5040 for compliance determinations in metal and nonmetal mines. MSHA also published a rule making for coalmines, but no exposure standard was provided. A standard based on particulate carbon is not considered practical because of coal dust interference. Interference may not be a problem if an appropriate size-selective sampler and EC exposure standard are employed. Sub micrometer dust concentrations found in previous surveys of nondieselized, underground coal mines were relatively low. If a large fraction of the sub micrometer dust is organic and mineral matter, sub micrometer EC concentrations would be much lower than sub micrometer mass concentrations. Laboratory and ?eld results reported here in indicate the amount of EC contributed by sub micrometer coal dust is minor. In a laboratory test, a sub micrometer EC concentration of 31µg m 3 was found when sampling are spirable coal dust concentration over three times the US compliance limit (2mg m3). Laboratory results are consistent with surveys of nondieselized coal mines, where EC results ranged from below the method limit of detection to 18µg m 3 when size-selective samplers were used to collect dust fraction shaving particle diameters below 1.5µm sub micrometer EC concentrations were ?7µg m3. In dieselized mines, sub micrometer EC concentrations are much higher.

By Edmund S. Leaver, R. S. Dean, T. L. Joseph

The metallurgy of manganese has developed along the lines of iron metal¬ lurgy. Enough high-grade ore has Been available so that by reduction with carbon it could be turned into an iron-ma.nga.nese alloy and a slag containing some 9 to 15 percent manganese. More siliceous ores have been smelted in the blast furnace to form iron-silicon-manganese alloys called spiegel. When lower-grade ores came in for serious consideration, which lias only been since l°l4, two types of processes received the most consideration — hydrometallurgical processes to produce a concentrate which could be smelted like the higher-grade ore and processes involving concentration of the manga¬ nese from manganiferous iron ores by preferential reduction of the iron (184)1. Special chapters in this bulletin are devoted to the production of ferro¬ manganese from ore, the hydrometallurgy cf manganese, and the Bureau of Mines modification of the preferential reduction process. Other methods of producing manganese alloys from low-grade or refractory ores have been suggested and may find future application. Manganese has a very high affinity for sulphur and is particularly adaptable to concentration by matte smelting. According to Betts (26), manganese silicate may be smelted with pyrite to give manganese sulphide and iron silicate. This method would be applicable to concentration of either the silicate or carbonate ores. The sulphide, once obtained, could be roasted to oxide and reduced in the usual way. Another possibility for the production of manganese from silicate ores involves their reduction by silicon or manganese silicides. Swedish Patent 52290, February 25, 1925. covers the reduction of a slag rich in manganese by silicon-manganese alloy containing more than 10 percent silicon, Joseph H. Brennan (38.) describes the concentration of manganese iron ores by partial reduction with silicon. Beckett (7,4,19) describes the reduction of manganese dioxide with a manganese silicide for the production of standard ferromanganese. Beckett gives as a typical alloy, manganese 64.4, silicon 24.6, and as a typi¬ cal ore, 5S.5O manganese as MnO^. The product of the reaction between these two is 80.11 percent manganese and 1.22 percent silicon.

May 1, 1934

By Robert E. Manning

At present, a need exists for more effective noise control in the coal-mining industry. In particular, new muffler designs with the required acoustic performance are needed for percussive pneumatic drills. Accordingly, the U. S. Bureau of Mines issued a contract to USS Engineers and Consultants to design a muffler capable of attenuating the noise from the air exhaust of a pneumatic drill. The specific objective of the contract was to design and deliver a prototype muffler that would attenuate the air-exhaust noise to 90 decibels on the A scale (90 dbA). The test drill used in this investigation was one used for roof-bolting purposes in coal mines. Using the combined approach of analysis by digital-computer program and experiment by simulated-noise tests, three prototype mufflers were designed and constructed at U. S. Steel Research. The mufflers consisted of a variety of resonator chambers and expansion-contraction chambers, and were of the following sizes: A muffler with a 3- by 5-inch elliptical cross section and about 8 inches in length. A muffler 5 inches in diameter and about 5-1/2 inches in length. A muffler 5 inches in diameter and about 10-1/2 inches in length. These mufflers were subjected to laboratory tests to determine their effectiveness in attenuating exhaust noise, mechanical noise, total drill noise, and simulated noise. All mufflers reduced the exhaust-noise level by about 25 dbA - from about 115 dbA without a muffler to below 90 dbA with a muffler - and thus were successful in meeting the contract objective. Field tests were conducted with the three prototype mufflers at U. S. Steel's Robena No. 4 Mine, and no icing problem was encountered. A fourth prototype muffler was designed to fit around the leg of the pneumatic drill. Tests showed that this kidney-shaped muffler also reduced the air-exhaust noise to below 90 dbA.

Jan 1, 1973

By Richard S. Gaps

In 1983 the U.S. Bureau of Mines conducted a mineral survey of the Golden Valley Wilderness Study Area (WSA), CDCA-170. The 29,887 acre WSA, located in the western Mojave Desert near Ridgecrest, California, is underlain by pre-Tertiary plutonic rocks and volcanic and sedimentary rocks ranging in age from Miocene (?) or Lower Pliocene (?) through Pleistocene and Recent. No mines were operating in the WSA in 1983, nor is any mineral production known to have come from the WSA. Two mining claim blocks, portions of which are within the WSA, and seven isolated prospects, four inside the USA, were examined and sampled. No mineral resources were identified. Widespread propylitic alteration, with localized argillic and alunitic alteration, occurs along the southern boundary of the study area. Samples from claims and prospects within the altered zones are anomalous in gold, silver and arsenic, and some contain antimony, tungsten and mercury, indicating gold resources may exist. Alluvial sample results suggest recent claims in the northwest corner of the study area may also have gold resources. Portions of the study area are within the Randsburg Known Geothermal Resource Area while other segments are considered prospectively valuable for oil and gas and for sodium.

Jan 1, 1985

By Robert P. Apa

Energy Incorporated has prepared this final report presenting the results obtained from the program for extracting alumina from anthracite culm along with the recovery of energy. This work has been accomplished under the auspices of the U.S. Bureau of Mines with technical coordination through the bureau's Reno, Nevada facility. The objective of this program was to develop a process to recover alumina and energy from Northeastern Pennsylvania anthracite mining waste. The program included Identification of sufficient resources to support a commercial facility, identification of the operating parameters which maximize alumina and energy recovery, the development of a conceptual process design, preparation of material and energy balance(s), and the performance of a system economical analysis. The program was conducted in three major phases. In the first phase the program concentrated on selecting several anthracite culm banks capable of supporting a commercial alumina producing facility. The chosen banks were then sampled and analyzed leading to the selection of two banks which were chosen far testing. The Harry E. and Eckley culm banks were the ones selected. Material from these banks was tested in Energy Incorporated?s Idaho Falls, Idaho testing facility. Parametric testing was accomplished in an eight-inch-diameter fluidized bed test facility. The test program consisted of twelve separate tests. After critical operating parameters were determined, the second phase started: process development in EI's 18-inch fluidized bed test facility. Three material and energy balance tests were completed in this facility. Following these tests a 72-hour demonstration test was performed. The data acquired from these tests were used in the last phase: the process conceptual design and economic analysis. The design basis was a commercial scale facility capable of producing 500,000 tons of alumina per year for 15 years. Based on the test program, It is technically feasible to build and operate such a plant today. The facility would produce, along with the alumina, 81.5 MWe of electricity for outside consumption. A preliminary rate of return indicates that the plant is not feasible with today's economic conditions. An increase in the market price of either the alumina or the electricity is required to provide an attractive rate of return for the facility.

Jan 1, 1982

By C. Özgen Karacan

Gob gas ventholes (GGV) are used to control methane inflows into a longwall operation by capturing it within the overlying fractured strata before it enters the work environment. Thus, it is important to understand the effects of various factors, such as drilling parameters, location of borehole, applied vacuum by exhausters and mining/panel parameters in order to be able to evaluate the performance of GGVs and to predict their effectiveness in controlling methane emissions. However, a practical model for this purpose currently does not exist. In this paper, we analyzed the total gas flow rates and methane percentages from 10 GGVs located on three adjacent panels operated in Pittsburgh coalbed in Southwestern Pennsylvania section of Northern Appalachian basin. The ventholes were drilled from different surface elevations and were located at varying distances from the start-up ends of the panels and from the tailgate entries. Exhauster pressures, casing diameters, location of longwall face and mining rates and production data were also recorded. These data were incorporated into a multilayer-perceptron (MLP) type artificial neural network (ANN) to model venthole production. The results showed that the two-hidden layer model predicted total production and the methane content of the GGVs with more than 90% accuracy. The ANN model was further used to conduct sensitivity analyses about the mean of the input variables to determine the effect of each input variable on the predicted production performance of GGVs.

Jan 1, 2009

By Thomas P. Mucho, David C. Oyler, Jim Pablic, Dennis R. Dolinar

A room and pillar coal operation in central Pennsylvania was experiencing roof cutters and long running roof falls caused by high horizontal stresses. The roof conditions created hazards for the miners, and caused several production panels to be abandoned prematurely. The mine requested assistance from the National Institute for Occupational Safety and Health (NIOSH) in applying the "advance and relieve" mining to reduce the affects of the horizontal stress during panel development. The "advance and relieve" plan that was developed called for removing a pillar on one side of the panel as it was being advanced, thus creating a cave. The caving then relieved a portion of the horizontal stress across the panel. Because the horizontal stress direction is key to the success of this method, stress mapping as well as mining experience was used to establish the direction of the horizontal stress. Subsequent field measurements provided an estimate of the stress magnitude. Three panels were mined using this technique, and good roof conditions were achieved in all these panels. Instrumentation was used to monitor the stress changes in the roof created by the cave. Stress relief of over 1,000 psi was measured 120 ft from the cave and to depths of 20 ft into the roof. The lateral extent of the stress relief zone across the panels appears to be about 400 to 500 ft. This case history has provided much insight into the practical application of the "advance and relieve" method discussed in this paper.

By Lyda W. Hersloff

An environmental monitoring program was established to assess the baseline of parameters which may be impacted by a research and development hydraulic borehole mining operation. During the baseline program, two aquifers were identified at the borehole site with the overlying sand aquifer being distinct from the ore sand aquifer on the basis of radiological parameters. The direction of flow of groundwater was determined to be north 19° west at a rate of 1.82 feet per year. Tests to determine the effect of backfilling the boreholes indicated that using overburden from the open pit mining operation would not significantly increase the radiological consti¬tuents of the ore sand aquifer. Mining measurements of the- radon flux from the borehole indicated that the actual release rate of 0.035 pCi/sec was several orders of magnitude less than the calculated estimate by the Environmental Protection Agency. Finally, a gamma survey conducted at the site indicated that the terrestrial component of background radiation was consistent with that in areas near uranium deposits. The methodology used as well as the supporting data are given in this report.

Jan 1, 1981

In the interest of safety in underground coal mining, the Bureau of Mines recommends: 1. That doors used to control ventilation (a) Shall be installed in pairs to form air locks, (b) Shall be self-closing, (c) Shall not have latches or other devices for holding them open, (d) Shall be constructed and maintained to prevent excessive air leakage through or around them, (e) Shall be fire resistant. 2. That wherever practicable the use of doors shall be limited to development openings. The Mine Safety Board is of the opinion that the best practice in coal-mine ventilation makes use of a split system employing overcasts or undercasts with doors limited as far as feasible to development openings. The distance between air-lock doors on haulageways should be sufficient to accommodate a trip or train of maximum length. Where auxiliary doors are installed to control ventilation during emergencies, they should be so placed that they can be utilized readily in case of damage to the air-lock doors.

Jan 1, 1938

By David L. Veith

This Bureau of Mines bibliography of U.S. and Canadian literature pertaining to revegetating coal-mined lands contains 805 references published from 1977 to 1984. Each reference is evaluated by keywords, providing the reader with a means of rapidly sorting through the references to locate only those dealing with the coal mining region and subject of interest. All references are annotated. Other sources of information are given, including Office of Surface Mining (OSM) and State reclamation agencies and other published bibliographies.

Jan 1, 1985

By Dale William Avery

Thirty mines and prospects were studied; 22 are within the Dolus Lakes RARE II area. Three properties within the area and one adjacent to it were determined to have indicated or inferred gold, silver, or molybdenum resources (fig. 1 and table 1) associated with quartz veins and shear zones or quartz-pyrite stockworks in granodiorite. Five other properties in the area and three just outside have potential for the discovery of gold and silver resources. Minor amounts of very fine-grained placer gold are in glacial outwash in and near the area. The John G. Carlisle Mine (fig. 1, no. 9) produced 120 oz (3.7 kg) of gold between 1897-1899. The Independence Mine produced 481 oz (15 kg) gold, 197 oz (6.1 kg) silver, and 189 lb (86 kg) of copper between 1926 and 1935. These mines are adjacent to the study area's northern boundary.

Jan 1, 1983

By Mark R. Pettitt

The charter of this investigation was to identify and promote the application of noise control technology to future longwall mining machinery. Intensive noise and vibration data were acquired on a typical longwall shearing machine, and the highest noise levels were shown to radiate from the cutter drums. Shearing machine cutter drum noise control techniques that take advantage of the nature of the dynamic forces generated during coal cutting were developed. These include both structural redesign and force isolation techniques. A reduced noise cutter drum was developed that achieved a 5 to 6 dBA system noise reduction at the operator's position. Its operational performance was verified by a six-month long in-mine test. It was evident from the data that additional noise reduction could be achieved by treatment of the shearing machine hydraulics. Noise control of secondary sources was also investigated. A method of reducing full or empty stage conveyor noise (and continuous miner conveyor noise) by 5 to 10 dBA was demonstrated through isolation techniques. Underground mine durability testing, however, is yet to be demonstrated.

Jan 1, 1986