Search Documents

By Richard L. Fowler

[Study and development of sensing techniques and sensors were performed to aid shuttle car drivers in detecting, obstacles and in guiding the car along the face haulage route. Microwave, acoustic, and optical sensing techniques were considered as part of the feasibility study for obstacle detection. Various guidance techniques, including wire-following and rib-ranging were investigated. Active optical sensing was selected for obstacle detection to obtain the bear overage and sharp angular cutoff characteristics required within the packaging limitations defined by the shuttle car configuration. Rib-ranging guidance was selected to achieve completely self-contained shuttle car system which responds to the mine geometry without need for wires, stripes, or other path defining devices. Extensive hybrid computer simulation runs were performed to valuate various guidance techniques during the feasibility study. Subsequent simulation rues were performed to establish parameter values for the rib-ranging guidance system. The obstacle detection and guidance system was designed, fabricated and installed on a standard shuttle car. The system satisfied all applicable permissibility requirements of Schedule 2G. An experimental permit was issued to Bendix for operation in an underground coal mine. System evaluation tests were performed first above ground at the Bendix Research Laboratories. The simulation model was validated by these runs. Final testing wan performed underground in an operating mine with an experienced shuttle car driver. All sensors successfully demonstrated Chi predicted performance capability during underground face haulage tests. Dust did not Impair system performance and lens cleaning was not required during working shifts. Further development is required to achieve the desired obstacle detection performance Closed loop steering control with manual override is recommended o: mended for the lateral guidance e system. The guidance system should be an invaluable aid to low-coal shuttle car drivers where continuous mining machines are utilized.]

Jan 1, 1973

By Thomas L. Ochs

The stripping of iron-laden solvent with hydrochloric acid in the iron-removal step of the clay-hydrochloric acid process for the extraction of alumina from calcined kaolinitic clay results in a loaded ferric chloride stripping liquor. Treatment of this stripping liquor at boiling with calcined kaolin to form insoluble Fe203(s) and a dilute A1C13 solution was undertaken by the Bureau of Mines to characterize process problems and to aid in sizing of solids-liquid separation equipment. Variables identified as important in the chemical reaction were calcined kaolin particle size, ratio of calcined kaolin to FeC13, and reaction time. These parameters were tested for significance and their interactions investigated. Fine calcined kaolin (-65 mesh) at a greater than 1:1 mole ratio of contained acid-soluble A1203 to Fe203 equivalent of the FeC13 in the stripping liquor required less reaction time than coarser (-16 mesh) material. Solids-liquid separation of the reacted slurries by both settling and filtration requires flocculation.

Jan 1, 2011

By Philip C. Good

Red mud residue from Bayer process treatment of Jamaican bauxite was dewatered in batch and in continuous centrifuges. Solids content of the residue was increased from its original value of 20 to 25 percent to about 40 percent by centrifuging. Clear effluent amounting to approximately 40 percent of the slurry liquid was recovered containing dissolved alumina and soda values for potential recycle to the alumina plant" Addition of a chemical flocculant to the centrifuge increased capacity by about 35 percent. Manufacturer's estimate of large-scale equipment requirements, based on data collected in this investigation, was that a proposed installation for dewatering 16,000 tons per day of Jamaican red mud would require twenty-two 24-by 60-inch solid-bowl-type centrifuges. Cost analysis of a proposed installation, based on a Jamaican red mud tonnage of 16,000 per day, is included also.

Jan 1, 1968

By C. E. Hennig

On January 1, 1961 there were 311 petroleum refineries in the United States with a total crude-oil throughput capacity of slightly more than 10 million barrels per day, according to the Bureau of Mines' annual survey. Compared with a year ago, this represents net increases of one in the number of plants and 109 thousand barrels per day in total capacity. Contributing to this increase was the completion of two new plants, one in Hawaii and another in Michigan, during the year. At the beginning of 1961 the industry was building facilities which will increase this overall crude capacity by 36,500 barrels per day. As part of its building program, it was also replacing 329,000 barrels per day of its present capacity. Of the total 10 million barrel per day installed capacity, the industry reported 380,000 barrels per day as being shut-down on January 1, 1961. This included 11,500 barrels per day considered inoperable without extensive reconditioning.

Jan 1, 1961

By Donald B. Lindsay

A new concept was proposed for a personal warning device for use by miners who may be exposed to health hazards from inhalation of alpha-emitting radionuclides, especially radon-222 and its short-lived daughters. Two successive prototype models of the proposed instrument were designed, fabricated and tested. The Personal Alpha Alarm, in its final form, weighs less than 90 g (3 ounces), and can easily he mounted on a miner's safety cap. It is powered r, by electricity drawn from the cap-lamp battery, and consumes less than 100 n A at 4VDC. It is entirely passive and has no moving parts. Alpha-radiation originating in the air around it is detected by a 5 cm2-area semiconductor-type sensor that was developed especially for this purpose. The presence of alpharadiation in the air is communicated to the wearer by means of a small flashing light-a light-emitting diode-clipped to the brim of the safety cap. When the intensity of alpha-radiation exceeds a predetermined threshold, the flashing mode changes to a continuous illumination, thus providing an alarm signal to the wearer. Because the detector senses all alpha-emitters in the air, including 222Rn, it is not able to measure Working Levels accurately. For its intended purpose, however, which is to give a timely warning of excessive levels (several times the normal control level) of radon and/or radon daughters in an individual's air environment, the Personal Alpha Alarm is expected to be a useful instrument.

Jan 1, 1978

The objective of this condensed handbook is to provide the inspector with guidance for recognizing hazards from inhalation contaminants in above ground work areas of underground and surface coal mining and processing facilities and evaluating these hazards by collecting samples or making field determinations and interpreting the analytical results. It will be carried with the inspectors during their surveys. The complete handbook should be left in their offices except for Appendix II which lists the compositions of products found in previous surveys. There are several portions of the condensed handbook which should prove most useful to the inspectors. The names and locations of these portions are listed below: Procedure for an Industrial Hygiene Survey (Page 2-1) Survey Check List (Page 2-3) Rules for Determining if Sampling is Required (Page 2-2) List of Most Frequently Encountered Contaminants (Page 2-5) List of Candidate Contaminants and their Sampling Conditions (Page 2-A) Interpretation of Results (Page 3-8) For obtaining information not available from the above mentioned portions of the handbook, the inspector is directed to the Table of Contents, and the Glossary of Terms (Appendix I).

Jan 1, 1975

By John L. Schaller

The Bureau of Mines, U.S. Department of the Interior, has investigated the extraction of alumina from domestic kaolin clay by leaching with boiling 26 wt-pct hydrochloric acid. Acid leaching of crushed calcined kaolin feed yields slurries that are slow settling and difficult to filter because of the presence of fine particles generated in crushing, calcining, and leaching. Laboratory research showed that tumbling and moistening crushed raw kaolin on a pelletizing disk caused the fines to agglomerate on the surfaces of the larger particles, while the sharp edges and corners of the larger particles were rounded off. Minus 16-mesh crushed raw kaolin was misted on a 36-in-diam, 8-in-deep pelletizing disk at rates of 175 to 250 lb/hr, and was calcined in either a rotary or a fluidized-bed calciner; negligible degradation occurred. The physical properties of the misted calcined kaolin were evaluated in the leaching system of the clay-hydrochloric acid miniplant. Only minor attrition occurred during leaching, and the slurry was readily filtered on a continuous belt filter.

Jan 1, 1982

By D. R. Babich, E. R. Bauer

Noise-induced hearing loss (NIHL) in mine workers, especially underground coal miners, continues to be a problem in the mining industry. The recently enacted MSHA noise standard, Part 62 – Occupational Noise Exposure (Federal Register, 1999), is aimed at reducing NIHL in the mining industry. The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting a cross-sectional survey of noise sources and worker noise exposures to address NIHL in various aspects of coal mining including surface mining, coal preparation plants and underground mining. In underground bituminous coal mining, noise surveys, consisting of full-shift worker noise exposure, time-motion studies and equipment noise profiling, have been completed on longwall and continuous miner sections in six underground coal mines. The studies revealed widely varying shift-to-shift worker exposures, with workers in certain occupations routinely exposed to potentially hazardous levels of noise. A summary of these studies is reported, including worker dose, source/dose relationships and equipment noise profiles.

By L. A. Morely

The overall objective of the subject contract was to investigate the application, economic, and safety considerations of electrical-shock prevention techniques applied to surface and underground mines. Volume I of the four-volume final report starts by summarizing all research performed, and synopses of the three other report volumes are included. The balance of this volume concerns one major task of the contract, the protection of maintenance personnel. After specifying the scope of work for the task, electrical is defined, and needed ground-fault relay characteristics to prevent ventricular fibrillation are established. This is followed by an analysis of alternating-current systems, a comparison of these systems with respect to body currents, and the advantages and disadvantages of the various ground-fault protection techniques. An analysis of direct-current systems for off-track vehicles is then covered. These analyses form the basis for the research recommendations which along with suggestions for future research, conclude the report volume.

Jan 1, 1982

The investigation summarized in this report addressed two primary issues: the determination and use of correction factors, and the development of guidelines for velocity measurement site selection. Other ancillary issues which were addressed include a comparison of measurement methods and devices, aircourse cross-sectional area measurement, and characteristics of mine airways. An exhaustive literature search and analysis was performed; extensive in-mine experiments were conducted; a quantitative analysis of the data was used to develop correction factor tables and site selection guidelines. The reported results of other researchers who have examined the correction factors and site selection criteria, were analyzed in light of the results of this study. The measurement devices included in the experimental phase were: vane anemometer, vortex shedding anemometer, a prototype thermoanemometer, smoke tube, and, oil of wintergreen. The measurement methods include single-point centerline, timed¬-point traverse, continuous traverse for the anemometers, and various distances and cloud positions for the smoke tube and oil of wintergreen devices.

Jan 1, 1983

Ohio has an estimated 46 billion tons of coal beneath 12,000 square miles of the eastern third of the state. Recoverable coal reserves within this vast area are estimated at 21 billion tons, 3.2 billion tons of which have been mined since 1800. Ohio is the eleventh-largest coal- producing state in the nation and ranks third nationally in coal consumption. Coal resources in Ohio lie in as many as 60 identifiable coal seams along the northwestern flank of the Appalachian coal basin. Except where interrupted by minor faults and erosional discontinuities, these rocks dip gently and uniformly to the east, simplifying the mining methods needed to extract the coal. Fourteen of Ohio's 60 coal seams are considered to be important, although only a small number of seams are currently being mined. Ohio first enacted a surface coal mining law in 1948, requiring in part a $100 per acre reclamation bond. Ohio progressively strengthened its surface mining law in 1949, 1955, 1959, 1961, 1965,1972,1975,1978, and 1981. At the time of its enactment, Ohio's 1972 mining law was one of the most stringent in the country. This law also created a state coal severance tax of four cents per ton to be used for abandoned mine land reclamation. Ohio received primacy to regulate the surface coal mining operations within the state August 16,1982. Its Abandoned Mine Land Program was approved on the same date.

Jan 1, 1992

By Fun-Den Wang

This report presents theoretical studies and experimental work dealing with the detection of dangerous roof and pillar conditions in underground mines through measure¬ment of temperature differences on the surface of the mine opening. The theoretical work is directed at modeling the circumstances where a loose slab of rock might be detected. The experimental work provides input data for the theoretical models. At the beginning of the project, little was known by the authors of the conditions that would permit detection of a loose slab of rock or coal by measuring the surface temperature differences. The U.S. Bureau of Mines had found that there were detectable surface temperature differences on the roofs and pillars of mines. The Bureau contracted with Colorado School of Mines to measure temperature profiles around mine openings in an effort to learn if the temperature differences they had detected were directly related to loose pieces of roof and pillar rock. The Bureau was principally interested in learning if loose rock could be found in coal mines by measurement of surface temperature differences with an infrared thermometer.

Jan 1, 1972

Development of automatic fire protection systems for large, mobile mine haulage equipment was initiated under Department of Interior's Bureau of Mines-FMC Corp. contract H0122053, "Improved Sensors and Fire Control Systems for Mining Equipment June 1972 to May 1973." After successfully designing and mock-up testing an effective economical automatic fire protection system, and after having demonstrated that the system could extinguish controlled fires on 100-ton capacity haulage trucks, USBM-FMC contract 110232059 was issued in June, 1973, to conduct further development and validation testing. This report documents technical progress and activity under the latter contract. Figure 1 shows areas of the two haulage trucks that were protected by the automatic fire protection systems tested during this program. Figures 2 and 3 are composites showing hardware and schematic diagrams of the systems tested.

Jan 1, 1974

By John J. Sammarco

The mining industry has the highest average annual fatality rate among major U.S. industries. To address this, the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory (PRL), is conducting major research programs to reduce the hazard exposure of miners. One of the recently concluded programs at PRL developed the enabling technology for remote-controlled mining. An application involves the manual process of extracting and hauling coal where operators, in the tight confines of a mine, can be struck or caught by mobile machinery. The approach to remedy this problem uses a guidance system on the continuous haulage equipment so that it follows the continuous mining machine that extracts coal. This, in essence, involves sensor-based docking of the machines. Sensors functioning in the hostile mine environment of dust, methane gas, and water play the key role. Computer analysis of the mining machine's movements and empirical machine characterizations established operating requirements and spatial limitations to ensure proper loading of coal into the haulage equipment. These data served in the selection of a guidance sensor. Technologies such as scanning laser systems and ultrasonic sensors have frequently been used in other applications, but were found unacceptable. However, a near-infrared sensor employing active targets met the requirements. The sensor has a nominal 75b conical field of view and a range from 0.1 to 18.0 m. For the single-target mode, nominal range accuracy was 4.3% at a distance of 3.65 m. Correction algorithms were generated, which reduced the error to 0.6%. Airborne dust testing showed less than an additional0.8% accuracy (worst case) degradation at dust levels up to 15 mg/m3. Using four targets, the nominal range accuracy was 0.4% without correction algorithms. Analysis of dynamic testing of a continuous miner and haulage showed that accuracy was maintained and total target loss did not occur. A guidance system for the haulage system to follow the mining machine does not exist commercially. Such a system can reduce fatalities, injuries, and exposure to dust and noise.

Jan 11, 1998

By J. H. Nixon

A three phase program evaluated commercial proximity warning devices, developed and designed a microprocessor-based electrostatic field measurement instrument, and utilized this instrument to investigate the electro-static fields about power lines. The Phase I program consisted of test and evaluation of these commercially available proximity devices. The evaluation results were reported in the Phase I report entitlted "Evaluation of Proximity Warning Devices II dated 22 February 1980. The Phase II program resulted in the design and development of a microprocessor-based Distributed Sensor A.C. Electrometer which measures the electrostatic field present at 17 discrete locations along a crane boom. Operator control of the measurement system allows simultaneous electric field measurements from 17 probes, print out of the electric fields measured, and data archiving on magnetic tape for post measurement analysis. Under the Phase III program, electro-static fields around a crane boom were measured by the instrument at 17 high voltage power lines of various voltages and geometries. The electric field data was processed and plotted versus boom distance from the power line. Analysis of the electric field data indicate that the distances at which a single sensor alarm will activate, vary by a factory of 3 to 1. This is due primarily to variations in boom orientation. The results also indicate that in the case of multiple power lines, a single electrostatic field sensor cannot reliably be used to determine the distance from a power line.

Jan 1, 1982

By Walter D. Holland

This instructors guide is intended for use in a course which teaches metal and non-metal mine inspectors to perform surveys for inhalation contaminants in above ground metal and nonmetal mine work areas. The handbook entitled "Handbook for Surveys of Inhalation Contaminants in Above Ground Metal and Nonmetal Mining and Processing Work Areas? is used as a manual during the course. The manual contains a survey check list, rules for determining if sampling is required, a list of most frequently encountered contaminants, a list of candidate contaminants and their sampling conditions, and a description of control procedures and devices. There are several experiments in this guidebook which the trainees perform to acquaint them with the sampling systems.

Jan 1, 2011

By John R. Rhodes

The objective of this project was to investigate the feasibility of analytical techniques potentially capable of determination of Mg, Al, Si, S, Ca and Fe in 1 to 2 mg samples of respirable coal mine dust, in a total analysis time of not more than 10 minutes per sample, using equipment capable of being truck mounted for field-laboratory operation. It was not essential that the technique be non-destructive, but the chosen technique is, and this enables the analysis to be performed directly on the 37 mm diameter membrane filter on which the respirable dust sample is normally collected. The sensitivity requirements are therefore quoted in terms of the units of measurement, µg/cm2. The detection limit (3o of the background criterion) should be 0.5 µg/cm2 or less. The precision should be 5% or better, at concentrations above which the detection limit is not the determining factor.

Jan 1, 1972

By Robert J. Pokora

This report summarizes the work performed under USBM Contract No. J0100038, "Demonstration of Noise Control Techniques for the Crushing and Screening of Nonmetallic Minerals." The objectives of the program were to: a. Identify the prevalent sources of crushing and screening noise in portable and stationary plants b. Design retrofit noise control treatments for those sources c. Field test control treatments under actual operating conditions. A census of the nonmetallic industry was performed to determine the number and types of crushing and screening equipment. Based on the census, eight plants were selected and surveyed to assess the variety of noise sources, determine the worker noise exposure to those sources, and to identify possible constraints that had to be considered in designing and installing the retrofit controls. Three plants were selected from those surveyed and retrofit noise control treatments were designed, including: a. A primary crusher operator control booth b. Screen decks made of resilient cloth c. Screen feedbox impact pads d. Rubber feed plate for secondary crusher e. Rubber feed chute linings for secondary crusher f. Noise attenuating curtain for secondary crusher. A new primary crusher control booth was installed at one plant, and the operator noise levels were reduced from 97 dBA to 78 dBA. Screen noise at the two secondary crushing plants was reduced by 3 dBA to 7 dBA; crusher noise was reduced by 5 dBA at one of these two plants. Noise levels at normal outside operator and cleanup locations were reduced by 4 dBA to 7 dBA at one secondary plant, but operator/cleanup noise levels were not significantly reduced in the second plant due to rapid wear of installed materials. At one of the two secondary plants the retrofit noise control materials displayed excellent wear characteristics. The rapid wear of retrofit materials at the second plant was due to improper materials being supplied and changing circuit conditions.

Jan 1, 1982

By Sandip K. Mukherjee

This report presents the results of the economic analysis of several applicable alternatives to increase airflow in four underground coal mines. Pressure-quantity surveys were conducted underground and measurements were also made at the main mine fan(s). The existing ventilation networks were modeled using the modified Penn State ventilation simulator. The applicable alternatives were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each of the alternatives included capital, operating and maintenance costs. These costs were expressed as annual ventilation costs per active section in terms of dollars per elm taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. A section of this report also deals with comparison of simulator predicted air quantity values against air quantity values measured underground. The computer outputs for each simulation run are presented in Volume II of this report.

Jan 1, 1983

By Maurice E. Bailey

The purpose of this study is to determine worker acceptance of modified mine equipment at various intervals during a twelve month period. A survey instrument was administered to the workers by two experienced miners in four interviews. All four interviews showed a significant positive response to all modifications, except the small size of the cab of the shuttle car; however, the small size produced significant negative responses with respect to comfort in each of the four interviews. Initially, (interviews one and two), there were significant negative responses with respect to manufacturer receptivity to operator suggestions and program management follow-through on operator suggestions; however, the third and fourth interviews showed no significant negative responses with respect to these items. Likewise, there were significant neutral responses in the first two interviews; however, the third and fourth interviews showed no significant neutral responses with respect to these items.

Jan 1, 1975