Search Documents

By Karl Christopherson, Vanessa de Viterbo

Trim blasting is an integral part of the mining processes at the Morenci Mine, a Freeport-McMoRan Copper & Gold Inc. property. Trim blasting near high-walls or Finals blasting requires a tighter distribution of energy but a reduction in total energy factor near the wall. Recent Finals blasting in Morenci Mine was allowing the shovel to dig to the final design limit, but causing high-wall instability due to excessive energy or production of energy (blast design and timing). Slope instability events reduced production in two of the three operating pits in Morenci over 2009. In order to avoid high-wall instability from Finals blasting, a new method was required. The new method utilizes air-decks, unconventional row timing, and blast design based on the geology predicted. Many different geologic structures and rock types exist in Morenci, and different strategies were needed for the many predicted geologies. Drill penetration rate and core mapping were the primary tools for determining the blast design. Patterns were designed within a consistent geology; with weaker rock types receiving a lighter load than the stronger rock types. Penetration rate returned by the drill would be the determining factor on the actual rock hardness. Maintaining the pattern geometry on Finals designs should not be an issue as long as the lb/hole is adjusted to reduce powder factor close to the high-wall. One requirement of Finals blasting should be that the powder factor matches the geology as closely as possible. A softer, fractured zone should use approximately one-half to two-thirds the explosive charge of a competent, sound geological zone. This has been incorporated into the final Trim blast design. It is impossible to protect every high-wall from close-in blasting, especially those with crossing prominent joint sets inclined toward wedge failure, but this new design has provided protection on walls where the mine was encountering problems.

Jan 1, 2011

By D E. Shaw, J B. Case, J Gusek

Explosive casting of overburden is defined as the use of explosives in blasting to move overburden to a spoil pile without rehandling. Studies of the economic feasibility of the method, and the formulation of a design hypothesis involving rock properties, and blasthole geometry are presented. These studies indicate that if technical feasibility can be demonstrated to increase surface coal production, considerable economic advantage would accrue to coal mine operators.

Jan 1, 1980

By Roger Holmberg, William Hustrulid

Swedish cautious blasting techniques were used to excavate a room at the CSM Experimental Mine in Idaho Springs, Colorado,as part of a ONWI/DOE sponsored nuclear waste disposal research program.

Jan 1, 1981

By Duane Skidmore, Francis Otuonye, Calvin J. Konya

Proper stemming not only affects the rock breakage process, but also controls the unwanted side effects of blasting such as airblast, ground vibration, and flyrock. Little research has been conducted on the behavior of borehole stemming material under high pressure loading conditions. The methods of selecting stemming particle size and necessary stemming length were previously determined only by trial and error in the field.

Jan 1, 1982

By B Kniivila, A B. Andrews, T Lerick, Keith Jansen

Minntac Mine is a large, open pit taconite mine located at the center of the Mesabi Iron Range in northern Minnesota. The planned development of the Mine in the direction of nearby communities prompted a comprehensive study of off-site blast effects that resulted in numerous refinements in blasting practices.

Jan 1, 1984

By D T. Froedge

This paper is a presentation of a coyote shot at the Oriskany Sand Quarry of the Pennsylvania Glass Sand Corporation, Berkeley Springs, West Virginia.

Jan 1, 1982

A major problem that has continued to plague the surface coal industry is blast induced damage to the coal seam. Atlas Powder Company has addresssed this situation through seven years of field research in full-scale production environments. Many operations across the United States have been evaluated.

Jan 1, 1990

By Milton Barbosa Landim, Denise de La Corte Bacci

Statistical methods of multiple regression analysis, trend surface analysis and principal components analysis were applied to seismographic data recorded during production blasting at a diabase quarry in the urban area of Campinas (SP), Brazil. The purpose of these analyses was to determine the influence of the following variables: distance @), charge weight per delay (W), and scaled distance (SD) associated with properties of the rock body (orientation, frequency and angle of geological discontinuities; depth of bedrock and thickness of the soil overburden) in the variation of the peak particle velocity (PPV). This approach yielded variables with larger influences (loads) on the variation of ground vibration, as well as behavior and space tendency of this variation. The results showed a better relationship between PPV and D, with D being the most important factor in the attenuation of the ground vibrations. The geological joints and the depth to bedrock have a larger influence than the explosive charges in the variation of the vibration levels, but frequencies appear to be more influenced by the amount of soil overburden.

Jan 1, 2002

By Clayton Thompson

Linear detonation wave generators (DWGs) shape a detonation wave so that every portion of the wavefront reaches the target “line” simultaneously. A projection-type linear DWG uses Gurney plate velocity predictions and Taylor deflection angle predictions to estimate the angle at which a thin projected flyer (typically metal) will impact a target. A mousetrap-style planar DWG consists of two projection-type linear DWGs working in succession to create a planar wave-front through shock initiation of each successive target explosive. The angle of deflection is critical to yielding a planar or linear wave profile. Gurney predictions, nominally accurate to within 10% of empirical results, may not yield ideal linear or planar detonation behavior when used with a grazing projection-type DWG, which typically requires accuracy within 2%. Simulations were conducted using AUTODYN hydro code to compare deflection angle prediction methods. Ranges of minimal error between Gurney and Taylor predictions and the results from the hydro code were determined, using PBX-9404-driven polyethylene flyers.

Jan 1, 2011

By Goran Lande, Bernt Larsson, Dennis Clark

The effects of vibrations on close surroundings has been studied in Europe and the United States extensively in the past three to four years due to the ever increasing demands of environmental control. Therefore, "routine measurements" or "standard vibration consulting services" are being carried out by numerous firms with widely different qualifications.

Jan 1, 1983

By Jorge Flores, Dean Nichols

Some view quantitative risk assessment (QRA) as difficult to understand and complicated to use. They are comfortable with the proven reliability of quantity distance (QD) and question the benefits of applying QRA principles to explosive safety. In response to such questions, a review of the history of the American Table of Distances (ATD) provides insight to the strengths and weaknesses of the concepts behind QD tables. Additionally, a closer look at QRA features that are available today will reveal stunning capabilities and improved user friendliness not available previously. This paper looks at the early days of explosive safety, the use and limitations of QD, the meaning of risk in the context of QRA and discusses recent developments that knock down barriers previously hindering acceptance of QRA among regulatory agencies.

Jan 1, 2015

By Neal Lee

Reduced relief horizontally means an increase in energy expended vertically into the rock surrounding the stemming column, and potentially through the stemming column. The vast majority of holes in any surface blasting operation are afforded two horizontal relief faces at the moment of firing, whether by existing relief faces in front of and to one side, or previously blasted hole(s) in front of and to one side of the holes in question. When the energy expended in any hole on the blast pattern has less than two Horizontal Relief Planes or faces (referred to moving forward here as “HRPs”) available to it at the moment of firing, a higher percentage of the available energy is directed vertically. In the analysis of recorded videos by the author, one will note the fact that stemming ejection/flyrock is observed to a much greater degree from the center of almost all patterns when they are timed to “pull out of the middle” (“box cut" timed patterns). This is because the first hole to fire in each row has only one Horizontal Relief Plane, which significantly decreases horizontal avenue for energy release for these holes. This of course results in an increase in the amount of energy expended vertically. This paper proposes a novel methodology to modify the stemming to better use the explosives energy of each hole, while controlling side effects such as flyrock and airblast.

Feb 6, 2023

By James Rowland, Richard Mainiero

When most people think of explosives transport they think of a hazardous operation. We all know that we aren’t allowed to transport explosives through tunnels and are discouraged from traveling through heavily populated areas. Popular opinion suggests that explosives transport is a very risky operation. The authors decided to look into this a little more thoroughly and found just the opposite to be true.

Jan 1, 2008

By Mike Higgins

"The purpose of mining and its related industries is the removal of, and usually the subsequentprocessing of, material from the earth. This includes mining for minerals, quarrying for stone, and civilexcavations. Where this involves rock, the most common method is to fragment the rock by blasting. "

Jan 1, 1997

By Gloria Contreras

The study aims to optimize the density of holes per tunnel section. The energy distribution, the one with the highest density, is used in the center of the diagram and is distributed homogeneously towards the contours with the lowest energies up to the contours to produce a perimeter control.

Feb 1, 2020

By M. Khaled, K. Abdel Rahman, M. Khattab

Helwan limestone quarry is located at a distance of 35 km (21.7 miles) to the south of Cairo downtown. Drilling and blasting operations are used to extract the limestone for the Helwan Cement Company (HCC). In 1980’s a new urban community was constructed adjacent to the quarry. This situation led to shifting of the old quarry 5.0 km (3.1 miles) to its current location, to avoid causing blasting problems to the new community. Unfortunately, the new quarry is opened in a highly faulted area, with weak zones of brittle materials. The drilling and blasting crew is facing many difficulties due to the geological complexity along these zones. Moreover, the extension of this community towards the new quarry makes the control of ground vibrations is very important.

Jan 1, 2008

By S. Evans, J. Phillips-White, D. Morton

The partnership between Orica and MMG at the Dugald River Zinc mine in Australia has led to the first global field trials and deployment of Orica’s Subtek™ 4D™ (hereafter referred to as 4D) Bulk Systems underground bulk emulsion blasting technology. This technology offers advantages over conventional bulk explosives by extending the range of energy and length of explosive column that can be charged in underground production. 4D gives blast designers energy options between Relative Bulk Strength (RBS) 50 - 150, delivered uniformly along the entire column in most blasthole conditions along with the ability to instantaneously modify the energy within an individual blasthole. During Phases 1 – 3 of the project from October 2022 to January 2023, over 57 tonnes of the 4D Underground emulsion were loaded in 17 stopes. The primary objectives of this phase were to reduce hanging wall dilution and improve stope recovery. While drilling and other parameters remained unchanged, the energy selection was tailored for specific situations, guided by a revision to the site's drill and blast standard. The design used low energy (RBS 50 - 70) in holes adjacent to the hanging wall and high energy (RBS 130 - 150) where stope recovery had historically been challenging, such as at the toes of long downholes. Initial results of the project focused on five stopes selected for their similarity to those used for the baseline data set. Although the 4D data set was small, the post-blast scans indicated favourable results for recovery and dilution. This suggests that selecting and delivering bulk explosive with tailored energy levels can improve stope performance.

Jan 1, 2024

By S. Klerkx, R Battulwar, J Valencia, J Sattarvand, E Emami, M. Soleymani Shishvan

A new technology for energy distribution optimization, supported by NIOSH.

Feb 1, 2020

By Shonn K. McNeill, Joshua Micah Hoffman

Security engineering is similar to other forms of engineering – the design is guided by the loads, materials, and desired function. For facility design, the load is the threat. Facilities that are designed with considerations for explosive hazards are designed with a shot, or series of shots, of a given size and distance from key locations. These facilities range from office buildings and industrial sites in developed nations to military and police stations in contingency areas. The challenge is the design shots are not often communicated to facility owners and managers. If the hazards change, whether it’s due to an increased capacity to cause damage by a threat or a decrease in capacity by a structure, not knowing the design shot means not knowing if security design needs to change. Blast modeling is an engineering tool that can be used to reverse engineer what a facility is suitable for, as well as be a tool for modifying security design for new conditions. This paper will examine military and civilian examples, including a case study of a military facility that did not know their as-built conditions and had to be rapidly closed; due to the determination their security engineering shortcomings could not be mitigated.

Jan 1, 2019

By Isaac E. "Chip" Harris

Any contractor who agrees to supply materials or to perform services for a sum, is well aware of the importance of proper pre-bid information. Being able to properly plan costs and methods results in profits that allow the contractor to prosper. The paper discusses procedures used in estimating pre-bid cost; in particular, drilling and blasting cost for highways, dams and general construction projects. It breaks cost down into five categories and relates them to a total estimate used in bidding and budgeting a construction project.

Jan 1, 1975