Search Documents

By Seung-Kyu Baek, Chang-Ha Ryu, Yang-Kyun Kim

Safety concern is one of the most important parameters in the design of building demolition by explosive blasting. Accidents were sometimes reported due to the flying chips of fragmented materials in building demolition work in urban area. Laboratory experiments were performed to investigate the failure behavior of reinforced concrete pillars under blast loading and to develop an effective protection technique. Sixteen reinforced concrete pillars were constructed with two sizes: 450×450×1800 mm and 600×300×1800 mm. The failure behavior and the flying chip velocities were observed by means of a high-speed camera. Protection scheme was designed and the effects of several protection materials were investigated. Two kinds of non-woven fabrics and wire net were tested as protection materials. The results showed that reinforcing bar was one of the important factors to determine specific charges, and that mesh size of wire net and tied-up method affected the protection of flying chips. Control of gas effects is also a key to the control of flying chips. It was recommended to use both wire net and nonwoven fabrics as primary and secondary protection materials. Such protection scheme was successfully applied to the explosive demolition of 16 and 17-story apartment buildings.

Jan 1, 2002

By Calvin Konya, Steven S. Spagna, Ed Smith

During Summer 2001, the U.S Army Corps of Engineers awarded a contract to the construction firm of Bush and Burchett of Allen, Kentucky, for the purpose of developing a 13 acre redevelopment site by removing approximately 2.5 million cubic yards of rock (fig. 1). The Redevelopment Site will be the future home for a large portion of the City of Grundy, Virginia. Additional work items include the construction and relocation of 3,000 feet of the Norfolk Southern railroad bed, the placement of 95,000 cubic yards of fill and the placement of 16,000 cubic yards of stone slope protection along the Levisa Fork River. Bush and Burchett received a notice to proceed with construction in July 2001. Currently, the contract is near completion. Current activities include: hauling of material from the Redevelopment Site to the disposal area; placing fill material on the Redevelopment Site, and placing Stone Slope Protection (SSP) along the Levisa Fork river. Approximately one year into the construction highly weathered rock, degraded to near soil- like condition, was encountered in the upstream portion of the excavation. Over one-third of the original cut slope was adjusted and the blasting specifications had to be amended to accommodate for the material that was encountered in this area.

Jan 1, 2005

By Aaron Nickoli, Brad Clark, Thomas Horan E. I. T.

The Canal Road Dip Slide is an active landslide located on South Pender Island, British Columbia. The effects of the fall 2021 atmospheric river prompted the British Columbia Ministry of Transportation and Infrastructure to initiate an emergency response project to realign Canal Road out of the active landslide zone for safe traffic passage. The work was tendered in a bidding process and included blasting and rock excavation work at the project site. Tetra Tech Canada Inc. was retained by the contractor to be their Blast and Vibration Specialist. The close proximities of an active landslide, a Canadian National Park, and other segments of construction posed stringent constraints to blasting. The governing constraints to blast design included a Peak Particle Velocity (PPV) limit of 3 mm/s (0.12 in/s) along the adjacent landslide centerline and a slide movement constraint. Sixteen blasts were executed throughout the scope of work to remove 2595 m3 (3394 yd3) of meta-sedimentary rock. Blast designs adhered to the constraints by utilizing up to quadruple decking in 50+ blast holes which lead to complex timing schemes. Several blasts were over 4 seconds in duration, with one at nearly 8 seconds. The landslide area was monitored with Shape Accel Arrays (SAA) throughout the scope of work that tracked geohazard slide movement during construction. The SAA data is presented, and the effect of blasting is discussed. Site specific parameters for PPV estimation were calculated and are presented. Collaboration and communication between the stakeholders allowed the project team to successfully overcome the technical challenges posed by the Canal Road Dip Slide.

Jan 26, 2026

By Mark Spaniel

Computer 3D modeling to evaluate the potential underground blasting fragmentation performance based on rock within calculated damage radii along drillholes, as well as the burden distance from explosives along each drillhole. The results estimated from the 3D computer models closely predicted results found in the real world testing.

Feb 1, 2020

By Egonk Arriagada, Jair Alarcon

The efficient use of energy in the ore comminution process is an increasingly important strategic issue for improving the productivity and competitiveness in the mining industry as is in recent years the related focus on reducing energy intensity on the atmospheric pollution and greenhouse gas emissions from its use.

Jan 1, 2015

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson, Brian Somes, Kevin Wegman

"To perform a probabilistic risk assessment (PRA), a method of quantifying the risks associated withinfrequent high consequence events, consequence models that generate representative estimates of human health consequences for a wide variety of representative scenarios are commonly used. Criteria that suitable models must possess include: (1) input requirements necessary to generate large volumes ofprobabilistic simulations; (2) the capability to output injuries with the necessary details and resolution;(3) the ability to capture the variety of different scenarios inherent in an assessment; (4) acceptable cost and computational requirements; and (5) sufficient stakeholder buy-in for community acceptance."

Jan 1, 2017

By Angel Rafael Fernandez, Yahya Khader Al-Harbi, Benjamin Cebrian Romo, Antonio Morato Medina

The kingdom of Saudi Arabia has set the goal to diversify their economy from oil into different fields including mining. As the vast Arabian Peninsula is explored, orebodies of Aluminium, Copper, Gold and Phosphates are found in high grades and tonnages. Hard rock is present in most of the projects and require high quality blasting in regard to ore dilution, wall control and fragmentation. Maaden Gold has currently 4 open pit mining operations 1 new opening and 2 underground. More projects are coming online in the next few months and years. A new generation of mining engineers need to apply drilling and blasting techniques that compete with modern and efficient open pit and underground mines.

Feb 6, 2023

By Charles E. Van Barneveld

RBH Note: the following item is a little different than the usual, in that it shows how explosives were used in the past to assist in putting down holes for iron ore prospecting on the early Mesabi Range of Minnesota. The way explosives were used would not even occur to the modern explorationist, given the equipment available today. The reason for the great difficulty in putting down a hole was that the area was covered with debris from the great glaciers of the past (the same ones that carved out the Great lakes). This debris consisted of boulders, clay, sand, and any other imaginable mixture of materials.

Jan 1, 2013

By Agus Sasmito, Akash Adhikari, Srivatsan Jayaraman Sridharan, Purushotham Tukkaraja

Previous studies on blast fumes(CO + NO2) clearance and workplace re-entry time have overlooked the effects of toxic gases entrapped in the muckpile. The currently available models forcalculatingthe mine re-entry times assume that all post-blast fumes are emitted upon detonation. However,recentstudies reportedthat as much as 60% to 70% of the fumes or gases produced during an underground development blasting couldremain entrapped in the adjacent rock mass or in the muckpile. Entrapped fumes are slowly released,and when disturbed, high concentrations are released, representing a possible risk during the digging and transportation of the muckpile. This study uses CFD, SC-Flow software to understandthe behaviorof the entrapped fumes and theireffect on mine re-entry time.

Feb 1, 2020

By Paulo Couceiro, Juan Navarro

The impact of rock blasting fragmentation and heave on digging performance in open-pit mining operations is usually the first true indicator of blasting outcomes. Within the typical excavation cycle, the bucket loading time or instantaneous digging rate are the ones that present the strongest correlation with rock fragmentation size distribution, swelling, and shape of the muckpile, a part of rock mass hardness, equipment size, power, and others. As the efficiency of unit operations becomes increasingly important for long-term mining strategies, cost-effective approaches are needed to increase mine productivity. In this line, the performance of downstream operations, such as digging, hauling, and comminution, may be affected by the energy input in blasting. This requires a better understanding of the explosive’s energy role in such unit operations in order to drive consistent improvements. Therefore, this paper examines the impact of the explosive’s energy distribution on shovel diggability from production shots carried out with different explosives in an open pit gold mine, with the aim of modelling the interface between blasting and excavation.

Jan 21, 2025

By Zheng Shuangying

The vibration effect of the buried oil pipeline caused by tunneling blasting affects the pipeline safe transportation, tunnel construction schedule and its construction cost. The dynamic response characteristic of the buried pipeline under blast loads is the foundation of designing blasting scheme as well as the prerequisite to pipeline safety. Taking the blasting engineering of Xiannvyan tunnel passing through a buried oil pipeline of the high-speed railway from Xi’an to Chengdu as the background, according to the space relation between tunnel and pipeline as well as the charge structure of V-cut blasthole, the 3D non-linear dynamic finite element model of tunnel-pipeline was established in the light of the equivalent explosive. The vibration response of the ground surface over pipeline resulting from V-cut blasting was simulated by LS-DYNA finite element program. Comparing with the measured vibration velocity waveforms in site, the accuracy and reliability of the numerical model are well verified. On the base of the simulation method, the coupling dynamic response characteristic between buried oil pipelines and soil was further studied and the Von-Mises stress distribution of pipeline wall was obtained. The safety of buried oil pipeline was quantitatively analyzed through the inside stress data of pipeline given by the simulation calculation above. The analytic results show that the maximum vertical vibration velocity of pipeline on the interface between pipeline and soil is 1.62~5.07 times as large as that of soil. When the buried pipeline is located over the tunnel and 13 m (42.6 ft) away from tunnel, the maximum vertical vibration velocity of ground surface caused by V-cut blasting with charge weight 17 kg (28.6 lb) is 3.17cm/s (1.25 in/s) and the vertical peak vibration velocity of pipeline top is about four times as the ground location directly above the pipeline. Meanwhile, the peak dynamic stress of the buried pipeline caused by blasting vibration is only 2.35% of the allowable stress of steel pipeline. The maximum superimposed stress of the blasting dynamic stress and the hoop stress produced by the pipeline internal pressure is 242.56 MPa (35 180.36), which implies that the buried oil pipeline is completely safe under the conditions of the given tunnel blasting scheme.

Jan 1, 2015

By Robert Hopler

On June 13, 1912, the final decree of dissolution of the DuPont explosives trust was handed down, and the resulting new companies began operating at the beginning of the new year. The property assets granted to (or retained by) the companies were as follows:

Jan 1, 2014

By S. Mansfield, A. Sharma

At a large open cut copper mine, in pit crushing and conveying is used to shorten haul routes and minimise stockpiling of ore. This strategy decreases capital expenditure by reducing the number of haul trucks and excavators required and reduces the need to rehandle ore from stockpiles with a secondary load and haul fleet, with an overall goal of lowering operating costs and carbon emissions. As the mine has developed and expanded, it was necessary to extend the conveying network and install a fourth, semi-mobile crusher to increase the output of the operation, while maintaining the operational efficiencies. This required the blasting of a new tipping bench and pocket for the installation of one of the largest and most powerful semi-mobile, crushing plants. Fed by 360 tonne (396 ton) ultra-heavy class haul trucks, the KB 63-130 Pro gyratory crusher is the highest capacity available in the market. This paper describes the holistic process that was applied to model, design and execute the blasts required to create the pocket for the semi-mobile crusher, the surrounding tipping bench, plus the conveyor corridor and access ramp used by the ultra-heavy class trucks.

Jan 1, 2024

By Guillermo Lazcano Ríos, Jorge Parvez Aguirre, Alejandro G. Díaz Berríos, Felipe Rodriguez Alveal

Codelco's Chuquicamata Underground Division (DCHS) faces issues due to collapses in its subsidence streets, which hinders the advancement of the subsidence front and leads to the loss of areas and reserves. To address these issues, DCHS and Orica have developed a new excavation methodology based on pre-loading explosives in high drawbell. This methodology involves creating a high drawbell extending from the floor of the production level to the ceiling of the subsidence level, divided into two phases: upper and lower. A resin stemming is used to separate these phases. The excavation strategy adjusts to variables such as reception volume, fluffing, and excavation geometry, involving vertical pre-loading of the explosive and the use of a separating element between the phases. The test aims to validate the new excavation methodology and the retaining element in the rock mass, evaluating aspects such as drawbell geometry, impact on the rock mass, damage to the retaining element, and fragmentation. Wireless electronic detonators are used in the upper phase to improve safety by eliminating the need for physical connections, while traditional electronic detonators are employed in the lower phase. Low-density bulk emulsion is applied to minimize the impact on the Crown pillar and extraction point, and higher-density explosives are used above the subsidence level to ensure good caving. Results showed that the blast achieved 86% conformity with the theoretical design. Resin stemming allowed for 100% effective detonation in the upper columns, and the fragmentation obtained was 5.44 inches, which was less than expected. No damage to the Crown pillar was observed, and the explosive quality met standards. This technique has proven to be effective and viable, suggesting the possibility of eliminating the subsidence level in future levels, resulting in savings, and providing greater stability to the rock mass.

Jan 21, 2025

By R. F. Favreau, Patrice Favreau

"Ever since we have started to assist those responsible for blasting with blast simulation studies, we havebecome aware of an interesting aspect, namely that in 90 % of cases we are asked ‘‘Can you seek ablasting method which gives better fragmentation than the method which we use now’’. But after a visit to the site, and the evaluation of the fragmentation obtained with their present blasting method, it very often becomes evident that it is the ease of mucking and not the fragmentation which requires improvement. Hence we then proceed to do a simulation study the results of which are improved mucking rather then more fragmentation, and those responsible for the blasting always become very satisfied."

Jan 1, 2017

By Steven Putt

The paper presents new results from Datacloud during recent Seismic While Drilling trials in iron ore, metallurgical coal, and hard rock mines around the world. The measurements are compared with wireline geophysical logs, core data, drill cuttings, and conventional measurement while drilling (MWD) systems to validate the technology and show how the data can be used.

Feb 1, 2020

By Joseph A. Meyers

Explosives techniques and technology are constantly evolving and improving, yet basic communication and business skills are not being used regularly. Many potential blasting projects never occur due to simplistic, basic factors, such as a lack of communication. Articulate communication is the key component in the blast approval process, which has changed remarkably from how business was conducted fifty years ago. Imperative to the approval process is communication outlining the safety and benefits of the blasting project.

Feb 1, 2020

By César Ugaz, Jorge Cardenas

Mitigating the vibrations resulting from a blasting rocks is one of the most common challenges that Peruvian mining has, since if this impact is not mitigated it can generate discomfort and altercations with neighboring communities and also puts the continuity of the mining project at risk. In that sense, we must establish control parameters to mitigate these effects as much as possible. As a starting point we must establish areas of interest that in this context would be the communities near the mine; first stage to carry out constant monitoring at these points, the registration of vibrations and noise is vital for the success of this control, with this information we can establish predictive models, the registration of elemental waves and the evaluation of human perception. In a second stage, this information allows us to make decisions in engineering such as the selection of delay times, elaboration of detonation sequence schemes, maximum amount of operating load per delay window, as well as the use of special load designs (Decks). There is a fear that these controls generate negative impacts to the process, referring to fragmentation, dig rate, throughput, etc. Since we limit the explosive load necessary for the results we need. To avoid this we use "Decks" type load designs under a sequencing between these under time calculations by elemental waves, which generate a reduction in vibrations up to 50%, also complying with strict regulations without affecting the power factors to comply with our performance indicators. Finally, in a third stage we must carry out a constant evaluation of results according to the progress of the mine.

Jan 26, 2026

By Eduardo Lozano, Vilem Petr

The use of explosives bring countless benefits to our everyday lives in areas such as mining, oil and gas exploration, demolition or avalanche control. However, because of the potential destructive power of explosives, strict safety procedures must be an integral part of any explosives operation. The goal of this paper is to provide a solution against the hazards which unfortunately accompany the use of explosives. For this reason, a blast shield is specifically designed and tested for protecting personnel against these unpredictable effects. This document will develop a complete analysis answering the following questions: what are the potential hazards from an air blast; what are their effects; and how can we be protected against them. In order to answer these questions, theoretical, analytical, and numerical calculations are performed. Finally, a full blast shield prototype is tested under blasting conditions proving its effectiveness as a safety device while explosives are used.

Jan 1, 2015

By S. S. Bud Jenkins

I went to an underground limestone mine recently to demonstrate the use of borehole liners. The liners were for horizontal holes in a normal “V” cut tunnel round. I hadn’t been in this mine for about 40 years. What a change. Way back they used cap and fuse and lit each fuse individually with a blowtorch. The face was about 40 feet wide and 14 to 16 feet high. They used ladders to get to the upper holes. The rounds were mostly slab rounds. I never saw this happen but had heard several times that the first holes were going off before the last holes were lit. I guess if this was true the use of slab rounds was a plus for safety. As far as I know they never had an accident but it was a scary procedure. There were a lot of scary procedures in the past and thankfully things have changed.

Jan 1, 2010