Search Documents

By Behzad Vaziri Hassas, Firat Karakas, Mehmet Celik, Onur Guven

Since dewatering is a costly process, removal of moisture from relatively fine size lignites is an important industrial problem. As the lignite gets finer, the presence of micropores and relatively low hydrophobic nature of lignite lead to trapping of large quantities of water in the coal matrix. Lignites used in power stations need to be dried to a certain degree of humidity before it is transferred to the combustion chamber. It is generally wise to dewater coal as much as possible by physical means before it is dried. However, dewatering cost in some cases may be prohibitive. Thus, sometimes removal of even little percent moisture may be of great help in such operations. Surfactants have been used to increase the efficiency of coal dewatering. It is crucial to select appropriate type and amount of surfactants in order to get higher efficiency. Since the hydrophobic characteristic of coals increases with increasing the coal rank, dewatering of bituminous and anthracite can be accomplished using low HLB surfactants (Oily), however, these surfactants are not efficient in the case of low rank coals like lignites and brown coals. It is suggested that adsorption of low HLB surfactants on high rank coals is governed by Acid-Base interactions rather than electrostatic and van der Waals forces. Since this characteristic in lignites is not strong enough, low HLB surfactants could not be effectively adsorbed on low rank coals to make surface more hydrophobic. In this paper, a special set-up has been designed to study the effect of high HLB surfactants on dewatering of fine lignite particles. It is shown that high HLB surfactants function more efficiently on low rank coals than low HLB ones.

Jan 1, 2014

By S. Kondratiev

Mechanism of the action of nonpolar physically adsorbed reactants in froth flotation is under discussion in the paper. It is shown that their basic influence on flotation includes removing of the kinetics restrictions of the flotation complex formation. Experimental data and practical evidence reported in the paper sustain the proposed mechanism. There are discussed potential dependence of the kinetics of dixanthogen formation on platinum and its influence on the induction time (IT).

Sep 1, 2012

By Y. J. Ferdosi

This paper presents the outcomes of the preliminary investigation focused on the potential usage of Electrochemical Impedance Spectroscopy (EIS) in minerals processing. Currently, Electrochemical Impedance Spectroscopy has been successfully employed in the characterization of multilayer structures formed as molecules adsorb on flat surfaces and is commonly used in bio-related research. Few studies have explored the application of EIS in minerals processing, particularly for mineral particles and flotation systems. In the first series of tests, the impedance response was investigated as a function of particle size, shape and hydrophobicity using model quartz particles. The particle size fractions and the shape were found to contribute to the impedance response. The more hydrophobic quartz particles resulted in a higher impedance values. Further tests involved pure sulfide minerals including chalcocite, bornite, chalcopyrite and pyrite. The AC impedance measurements were conducted as a function of collector (sodium ethyl xanthate) dosage. The AC Impedance data was modeled using the combination of reference circuits. It has been shown that adsorption of collector onto sulfide minerals surfaces results in a higher magnitude of impedance. Increasing the collector dosage resulted in an increase in AC impedance for chalcopyrite, while a decrease was observed for chalcocite. Significant variations in impedance were exhibited by bornite and pyrite with a gradual increase in collector dosage.

Sep 1, 2012

By Diego Mesa, Willy Kracht

Frothers may be classified as weak or strong depending on their ability to produce stable froths, which is related to the amount of water that they transfer from the pulp to the froth. They can also have an effect on the non-selective mechanism of recovery by entrainment, implying that both selectivity and froth stability are, at least to some extent, frother dependent. Solids, on the other hand, also have an effect on froth behaviour. Clays, which are characterized by their small particle size, laminar shape, and high specific surface, tend to report to the froth phase and have an enormous impact on both froth stability and the overall performance of the flotation process. The purpose of this work is to shed light on the effect that different frothers have on the froth behaviour when clays are present. In order to do that, two sets of experiments were conducted using frothers from the families of alcohols and polyglycols. For each test, the equilibrium froth height was measured at different frother concentrations in an agitated machine with an acrylic square-base cell that was 11 cm wide and 25 cm high. The cell was designed in such a way that froth was able to grow without concentrate discharge. In the first set of tests, pure clays such as kaolinite and montmorillonite were used. In the second set, an actual copper sulphide ore with a high content of clays was used as solid phase. The results, expressed as curves of equilibrium froth height against frother dosage, showed a coupled effect of frother-clay on froth behaviour for both sets of experiments. In some cases, the froth grew up until the border of the cell with only a few parts per million of frother. In other cases, the equilibrium froth height varied smoothly with frother dosage. The results suggest that choosing the right frother can be of use for controlling the froth behaviour when dealing with clay-rich froths, using frother dosage as the control variable. The application of these findings at industrial scale are discussed and some recommendations are given.

Jan 1, 2018

By I. I. Maximov

The paper describes the results of studies performed with a view to develop an improved technology for processing high-grade massive and cupriferous ores of the Talnakh deposit, the main valuable components being nickel, copper and PGM. The studies? main task was production of nickel concentrate with nickel content of approx. 15%, nickel recovery being as high as possible. The studies were performed on two ore samples. One sample was a mix containing high-grade massive (78%) and cupriferous (22%) ores with nickel content of 1.93% and copper content of 3.6%; the other sample was a mix of high-grade ores with nickel content of 2.25% and copper content of 3.72%. Main ore minerals were copper sulfides ? chalcopyrite and cubanite, their total content being 10.5% ~ 11%, pentlandite (5.2% ~ 6.1%) and pyrrhotite (36.7% ~ 42.9%). Influence of grinding media on pentlandite and pyrrhotite separation results, achieved through combined use of triethylenetetramine (TETA) and sodium sulfite (SS), was also investigated. It is shown, that combined application of TETA/SS in the ratio of 1:2, permits to grind products in metal mill (mild steel) with metal balls (mild steel), achieving results that are similar to those achieved by means of grinding in inert grinding media with TETA/SS ratio of 1:1. Application of the developed technology provided for production of high-grade nickel concentrate with nickel content of 14.7% ~ 15.6%, nickel recovery being 76 % ~ 77%. Earlier experiments performed on the above mentioned ore mix permitted to produce nickel concentrate with nickel content of 10%, nickel recovery being 75.9%. Consequently, nickel content was increased by 4.7% ~ 5.6%, and a higher nickel recovery was achieved. The paper also describes metallurgical results related to nickel, copper and PGM with regard to all processing products.

Jan 1, 2014

By B. Y. Tuo

This article presents results of studies performed to determine the feasibility of using low-grade limonite ores from Yunnan deposit. Laboratory tests and commercial trials have shown that the magnetic separation can be performed with a high high-grade concentrates. The quality of the preparation concentration meets the requirements for blast-furnace smelting. The results as a whole demonstrate the feasibility of utilizing bank limonite ore. Yunnan limonite?s magnetic separation, roasting magnetic separation and flotation experimental study shows that grade of the ore grade can been from 32.91% heighten to 58.64%, a recovery of iron is 90.87%, productive rate is 51% through orthogonal test optimization; roasting magnetic separation can obtain that the grade of iron preparation concentrate is 61.16%, recovery is 67.39%, productive rate is 36%. As far as economy and enviormental protection is concerned, strong mag-netic suggested a more appropriate process. Keywords: Limonite; Roast; Magnetic separation

Jan 1, 2014

By Jochen Petersen, Steven Bradshaw, Guven Akdogan, Ngoie Mpinga, James Mwase, Jacques Eksteen, Cornelius Snyders

"The platinum group metals (PGMs) and associated minerals are particularly refractory to most traditional direct leach processes. However, the remoteness of many new ore deposits, socio-political risks, the scarcity of skilled labor and constraints on the availability of water and electrical power makes it increasingly more difficult to implement the conventional mill-float-smelt-refine process routes to extract and refine PGMs in remote areas. This paper discusses a process to extract PGM’s from low grade ore and concentrate using a sequential stage heap leach process entailing heap bioleaching and high temperature cyanide leaching, and evaluates the feasibility of implementing a carbon-in-pulp process to recover the PGMs from the pregnant leach solution. The heap bioleaching extracts the base metals in an acidic sulfate medium using a mixed culture of thermophiles. After heap bioleaching the heap is reclaimed, rinsed, agglomerated and restacked for high temperature cyanide leaching where the cyanide liquor is directly heated via solar energy in panels. Palladium, gold and platinum are recovered during the cyanide leaching stage. The pregnant leach solution was evaluated for potential carbon-in-pulp adsorption and subsequent elution similar to gold processing. The kinetics of adsorption and elution compared well with gold adsorption and elution."

Jan 1, 2014

By G. Venkateswara Rao

The jigging of ferrous ore to produce higher-grade products has been practiced for many decades. This is due to easy separation, a beneficial trade- off between operating cost and reduced yield relative to Dense Media Separation (DMS). Jigging becomes prominent for beneficiation of iron ores in the coarser size range. At present drive is towards the use of under bed air pulsed jigs for the beneficiation of ferrous ores. The main advantage is that the under bed air pulsed jigs are capable of generating the large pulse of amplitudes required to fluidize a deep bed of heavy ores particularly lump iron ore up to 40mm size. The major jig parameters effecting the jigging operation are bed height, shape of the pulse, residence time, operating pressure, valve cycle time and water flow rate. With the pulse shape set correctly for optimum stratification rate, even it is still necessary to provide enough residence time, to ensure the difficult material will take time to migrate to the expected layer in the bed. In order to find the Jig Stratification Index (JIS) parameters like bed height, operating pressure, water flow rate, cycle valve time and shape of the pulse were optimized first by conducting various tests. Typical Iron ore samples from Odisha (both lump and fines) were subjected to stratification studies at residence time of 1, 5 and 15 minutes. Jig Stratification Index (JSI) for both lump (0.30) and fines (0.20) were determined by using APIC Jig. The maximum possible JSI was calculated by using heavy liquid separation test (0.42 for lump and 0.24 for fines). It is found that the jig bed JSI is less than the Heavy liquid JSI for both lump and fines. The ratio of Jig bed JSI to the heavy liquid JSI is 0.83 for lump and 0.71 for fines. The JSI and ratio of Jig bed JSI to Heavy liquid JSI are low for fines due to fluid turbulences causing some degree of remixing in the jig bed. The fluid turbulences are more for fines than lump, hence jigging of fines is difficult and challenging. Keywords: sub grade iron ore, gravity separation, jigging, apic jig, stratification, residence time, jig stratification index

Sep 1, 2012

By O. Guven, I. Karaagaçlioglu, O. Ozdemir, M. Çelik

In this study, the effect of morphological properties such as shape factors and roughness of the glass beads on their flotation efficiency were determined using image analysis and profilometer methods. There is a considerable correlation between the shape factors, surface roughness and flotation behavior of the glass sample. These results indicate that as the particle shape is away from roundness and smoothness, it acquires more hydrophobicity.

Jan 1, 2014

By Christopher Robben, Alexander Mosser

"X-ray transmission (XRT) sorting has been introduced into the minerals industry in 2006 and has found various applications in diamonds, industrial minerals and metal ore processing since. The technology offers planar projections of the atomic density of single particles similar to the principle known from airport scanners, but being capable of treating up to 150tph per metre working width. In 2010, a pilot operation using a belt-type sensor-based sorter went into production at the Mittersill mine to treat the fraction 16-28mm. After an optimisation phase, the results were superseding expectations and therefore in 2012 a bigger production plant was set up. Two XRT-based sorters are parallel in operation since. One is treating the fine fraction 16-30mm while the other one is treating the coarser fraction 30-60mm after the secondary crushing stage. The XRT sorters are operated with the objective to reject barren waste before it enters the mill and flotation plant. 105,000tpa of waste material are rejected per year and can be sold as aggregate for road construction. This means that about 22% of the run-of-mine ore are rejected at an early stage with a waste reject grade lower than 0.03wt%WO3. The installation has not only led to lower specific operating costs but also led to reduced tailings disposal in an environmentally sensitive area. This allows the mine to reduce its headgrade which allows for a longer mine life. Alternatively it is possible to produce more tungsten concentrate, which is delivered to the smelter. This article will introduce the technological principle of XRT-based sorting and will discuss the flow-sheet of the Mittersill mine. Experiences that have led to the current plant design are described as well as the impact it has on the operation."

Jan 1, 2014

By I. N. Gridasov, V. V. Khromov, R. I. Ismagilov

"Over 50 mln.tonne is the average annual output of oxidized ferruginous quartzites typically containing Fe38-42% mined in Mikhailovskoye ore field. The most promising and cost-effective way to expand concentrate production maintaining current output of magnetite is processing of oxidized ferruginous quartzites (hereinafter referred to as OFQ) mined as a by-product in Mikhailovsky open pit mine. However lack of proven and efficient concentration and agglomeration process applicable to OFQ and insufficient data for feasibility evaluation of OFQ processing encumbered full-scale addressing of this challenge. Based on outcomes of multiple various studies a process of OFQ flotation was designed by MC Metalloinvest LLC and PJSC Mikhailovsky GOK engineers. Comparative lab-scale testwork have proven performance and production advantages of flotation against magnetic separation feat. flotation and combined concentration method. Lab-scale flotation enabled production of concentrate with average Fe66.6% and SiO22.06% grade. Geologic and production contouring of OFQ deposited in Mikhailovskoye ore field has been carried out to collect necessary data for feasibility study incl. cost and profit estimation. As a result processing and production properties of over 3,500 samples have been analyzed which is characteristic of every direction and level of prospective ore mining within Mikhailovskoye ore field up to year 2032. Following work has been done based on geologic and production contouring of OFQ: – natural typification of ores and production (processing) grades of OFQ, determination of average mineral composition; – correlation analysis of interrelation between OFQ mineral composition and processing features thereof for overall bulk of samples as well as for individual data blocks related to various directions of open pit mine; – OFQ classification with account of defined mineral composition and processing features. Total Fe weight content in chamber product of flotation (known as concentrating ability in flotation) was applied as a major differentiating factor for processing grade classification of OFQ. Three processing grades of oxidized ferruginous quartzites were established as a result of flotation tests run to determine concentrating ability, i.e. – hard concentrated OFQ (TO) – below Fe65%; – mean concentrated OFQ (SO) – Fe65-67%; – easy concentrated OFQ (LO) – over Fe67%. Outcome of this work provided initial data for feasibility study and cost-profit evaluation of medium-term industrial-scale processing of OFQ deposited in Mikhailovskoye ore field."

Jan 1, 2018

By G. Mucsi

This paper deals with the laboratory investigation of cathode ray tube (CRT) glass based glass foam, a relatively new product so called ?Geofil bubbles?. The main process engineering material properties of raw materials, such as particle size distribution, moisture content, density and specific surface area are shown. Then the preparation of raw cathode ray tube glass waste is presented including the following steps: crushing in impact crusher, grinding in laboratory scale ball mill, mixing, pelleting and sintering. We found that it was possible to produce foam glass (with proper mechanical stability and particle density) from the investigated waste CRT glass. The material characteristics of the final product strongly depend on the sintering conditions. Optimum conditions were determined particle size fraction was found to be 4-6 mm, temperature 800 0C, residence time 7.5 min. Keywords: waste CRT glass, grinding, pelleting, sintering, glass foam

Sep 1, 2012

By Darryel Boucher, Raymond Langlois, Neil Rowson, Kristian Waters

The Knelson Concentrator is a centrifugal gravity concentrator composed of a high speed rotating bowl into which a mineral slurry is fed. The rotational motion creates a centrifugal acceleration up to an equivalent of 200 G. Under this acceleration, particles enter fluidised riffles along the side of the bowl, with the fluidisation allowing for the substitution of dense material for less dense. The separation mechanism is not fully understood and questions remain on the optimal residence time, slurry feed parameters and bowl surface profile to achieve a better separation. The positron emission particle tracking (PEPT) technique has been applied to record the motion of a -1700+1180 µm particle of a quartz-gold matrix, labelled with 18F radioisotope while it undergoes concentration inside a 3" laboratory scale Knelson Concentrator (KC-MD3) operated at 60 G. The slurry used was composed of quartz and magnetite. Particle trajectories during the first stage of the concentration process where the heavier particles centrifuge through the increasingly dense slurry towards the riffles of the bowl are shown with respect to time. This work reveals new information on particle motion inside the Knelson Concentrator and the results will be used for validation of developed separation model as well as optimisation of a centrifugal concentrator’s performance.

Jan 1, 2014

By A. Singh, M. Ntlhane, V. Ross, M. Dlame

"Fine valuable particles are often lost to flotation tailings streams due to inefficient collection by air bubbles as well as passivation of surfaces by oxidation and slimes. The application of high-shear hydrodynamic cavitation devices (HCDs) to overcome this problem has already proven to be a considerable success in the industry. This paper details the results of further investigations that were undertaken at Mintek to better understand the mechanisms involved when preconditioning feed slurries in an HCD. By promoting inter-particle attrition and conditions of high shear within the reactor, cleaning of particle surfaces is enhanced as well as the formation of superfine (nano) bubbles which are believed to aid their agglomeration and subsequent collection by normal sized bubbles. In order to broaden the envelope of understanding with regard to application of the technology, rather than tailings material as investigated earlier, a Platinum Group Mineral (PGM) UG2 ore from the Bushveld Complex in South Africa was used in this study. The results of a series of batch flotation tests in a 10L Denver cell are presented, being conducted after the feed has been subjected to different methods of preconditioning. It was demonstrated that the preconditioning significantly improved the flotation kinetics of the PGMs, the optimum being obtained after around 20 passes through the reactor. This was accompanied by a much enhanced recovery-mass pull relationship and a significant improvement in the grade-recovery response. Significantly, the selectivity between the PGM and the deleterious chromite (expressed as Cr2O3) gangue more than doubled under these conditions. Modelling of the PGM data by means of the modified Kelsall model indicated that both the fast and slow floating rate constants were improved.INTRODUCTIONIt is well known that the flotation recovery of fine and ultrafine particles, typically less than 10 micron in size, is a challenge (Yoon et al., 1989; Miettenin et al., 2010). Although these particles are typically well liberated, due to their very low mass and inertia, the collision efficiency with air bubbles is low as a result of the inability of particles to penetrate the liquid streamlines around bubbles. Hence the probability of contact is often regarded as the ratedetermining step in flotation of ultrafine particles. Introducing more power into conventional flotation machines is likely to solve only part of the problem, as conventional mechanisms are effective only to a point in terms of shear and micro-turbulence. Further challenges are posed by the treatment of low-grade or oxidised tailings dump material, where valuables are passivated due to prolonged exposure to the atmosphere or slimes. Over the years, various mitigating strategies have been investigated, including the use of dissolved air flotation (Martinez-Gomez et al., 2013; Calgaroto et al., 2015), shear flocculation (Subrahmanyam and Forssberg, 1990), seed or carrier flotation (Tabosa and Rubio, 2010), sonication to clean particle surfaces (Aldrich and Feng, 1999; Newell et al., 2006), high intensity conditioning (Bulatovic and Salter, 1989; Chen et al., 1999; Tabosa and Rubio, 2010), and various electrochemical approaches such as changing Eh in order to promote formation of dixanthogen, dissolution of oxidation products by lowering the pH, activation by sulphidisation (Newell et al., 2006; Becker et al., 2014), and the use of alternative collectors."

Jan 1, 2018

By Y. H. Tang, H. Y. Zhang

"Tailings from lead-zinc mine contain plenty of dolomite and low-grade fine-grained barite, which is difficult to enrich by mineral processing. Since the density of barite and dolomite has some differences due to the fine dissemination size in a complex sedimentary, the gravity separation tests were conducted with no results obtained. The magnetic separation was conducted to remove the magnetic gangues, and the results were not satisfactory because of the gangue minerals such as limonite and others were low in content. The results of floatation tests showed that the mineral separation of barite and dolomite is quite difficult because that they have similar mineral floatability. Experimental research shows that the good results can be obtained by “desulfurizationbarite floatation” processing with the new depressant TS. The barite concentrate containing BaSO4 91.27%, BaSO4recovery is 70.25% when sodium dodecyl sulfonate serves as a collector and TS as the depressant.INTRODUCTIONBarite is an important mineral material. Often associated with other minerals, it usually needs to be separated by mineral processing in order to meet the application requirements. The main barite beneficiation methods include hand sorting, gravity separation, floatation, magnetic separation, acid leaching, etc. Usually barite associated with oxide ore such as fluorite dolomite, quartz ore etc. are also associated with sulfide ore such as pyrite, sphalerite and galena. The separation between barite and sulfide ore (such as pyrite) is easy. On the other hand, the separation between barite and oxide ore (such as dolomite and fluorite) is very difficult. There are quite a lot of reports on the separation between barite with fluorite dolomite however the separation between barite and dolomite is seldom discussed.The ore properties are quite complex attributable to mineral assemblage containing a large amounts of dolomite. As the density of barite and dolomite has some differences, gravity separation between them is usually easy. The gravity separation tests were conducted with no results obtained due to the fine dissemination size in a complex sedimentary. The magnetic separation was conducted to remove the magnetic gangues, and the results are not satisfactory as the gangue minerals such as limonite and others were low in content. Due to the fine dissemination and intimate association of minerals, and barite and dolomite contain the same group ions of Ba2+, Ca2+ and Mg2+, the results of flotation tests showed that the mineral separation between barite and dolomite by flotation means problematic. Previous studies have been conducted by several institutions but none to date has come up with a satisfactory process in dealing with the deposit. This may be attributable to: high cost of reagents; unsatisfactory performance. Therefore, the key to the flotation separation of barite and dolomite is the application of selective inhibitors. Based on previous test observations and years of extensive research experience in barite processing technology, with the new depressant TS has selectivity inhibition on dolomite developed and used, good results can be obtained by “desulfurization-barite flotation”, which allows barite in the lead-zinc tailings to a comprehensive recovery."

Jan 1, 2018

By V. A. Ivanova

Modification of hydrophobic part of carboxylic collector molecule is an upcoming trend for producing new reagents and changing its flotation properties such as activity, selectivity, sensitivity to hardness salts that inevitably present in the pulp liquid phase in the processing of ores containing calcium minerals. A wide range of apatite collectors ? monoalkyl ethers and monoalkylamides of dicarboxylic acids ? succinic, o-phthalic and maleinic acids have been synthesized by the addition of aliphatic alcohols and amines with various hydrocarbon radical value (from ?11 to ?16) to anhydride of the corresponding acid. Using computer modeling based on ChemBio 3D program of specialized complex Chem?ffice the calculation was carried out of charge distribution on atoms, energy parameters of molecules for investigated compounds. Calculated values of absolute hardness (?=6.75 ? 12.36) and absolute electronegativity (?= 5.67 ? 8.90) of the reagents showed that monoderivatives of dicarboxylic acids refer to the ?hard? type of bases. The degree of a charge transfer during calcium compounds formation of considered collecting agents (?N=0.009 ? 0.143) has been computed. Dissociations, micelle formation in solutions of these reagents and its hydrophobic and collecting properties were investigated in respect to apatite. Dependence of bulk, surface and collector properties on collector molecule architecture (double bond or benzene ring and non-ionogenic functional group in the structure of hydrocarbon radical) has been established. It is shown that experimentally determined dissociation constants (??a=5.16 ? 5.60 for succinic acid derivatives and ??a=3.32-3.78 for maleinic and o-phthalic acid derivatives) perfectly correspond to acidic properties predicted by computer calculations. Compounds of monoalkylderivative dicarboxilic acid have been determined optimum in composition and structure. The results of apatite flotation from apatite-nepheline ores of the Khibiny deposit (the Kola Peninsula) are presented here and show benefits of selected reagents. Keywords: monoalkylderivatives, dicarboxylic acids, reagents, microflotation

Sep 1, 2012

By Wei Zhang, Jinhong Zhang

"In froth flotation, the adsorption of collector on mineral surface is critical for a successful flotation process. In present work, an atomic force microscopy (AFM) has been applied to study the adsorption of potassium amyl xanthate (PAX) on copper sulfides, i.e., chalcopyrite, chalcocite and bornite. The in-situ collected AFM images show that PAX adsorbs on chalcopyrite mainly in the form of oily dixanthogen; while it strongly adsorbs on chalcocite and bornite in the form of insoluble metal xanthate, which binds strongly with the mineral surface. The information obtained from the AFM study shed lights on the collectivity and therefore the selection of specific collector for different copper sulfide minerals in industrial practice.INTRODUCTIONFroth flotation, which treats the highest throughput in mining industry and produces the maximum economic outcome of any surface chemistry process, has been widely applied for the concentration of copper sulfide minerals, i.e., chalcopyrite, chalcocite and bornite. In flotation, collectors are added into the pulp (mixture of water and fine-grained minerals) to selectively adsorb onto the target mineral and render its surface with high hydrophobicity, which is generally beneficial for a strong mineral-bubble attachment and thus a high flotation recovery. Therefore, the adsorption of collector on mineral surface is vital for a successful flotation process and it has been studied by applying various surface analysis techniques, such as IR (Infrared Spectroscopy), CV (Cyclic Voltammetry) and XPS (X-ray Photoelectron Spectroscopy). (Poling, 1963; Allison et al., 1972; Mielczarski et al., 1984; Leppinen et al., 1989; Kartio et al., 1996) These studies have revealed a lot of information, such as the reaction, product and mechanism, of the adsorption of chemicals on mineral surface. It is also of great interest to directly get the image of adsorbed collectors on mineral surface changing with pulp chemistry, such as pH, redox potential, ionic strength and chemical’s dosage."

Jan 1, 2018

By S. Vimalnath

The bioremediation capability of Pseudomonas aeruginosa cells was investigated for the biosorption of lead ions from aqueous solution. The various parameters such as pH, kinetics, biomass loading and concentration of lead affecting the biosorption process were studied. Complete bio removal of lead could be achieved for an initial concentration of 12.4 mg/L at pH 6.2, corresponding to typical industrial effluents. The biosorption isotherm followed Langmuirian behavior and the Gibbs free energy (?G) was determined to be-30.8 kJ/mole, indicative of chemisorption between the functional groups of the bacterial surface and lead. The biosorption kinetics adhered to a pseudo-second order model. The possible mechanisms of interaction of lead with the bacterial cells are discussed. A carbon paste electrode with a coating of biomass was developed for lead ion detection in aqueous solution using cyclic voltammetric technique. Concentrations of lead up to 5x10-5 M could be successfully detected using cyclic voltammetry, which could be improved to a detection limit of 1x10-8 M adopting differential pulse anodic stripping voltammetry (DPASV). Keywords: Pseudomonas aeruginosa, bioremediation, lead, voltammetry

Sep 1, 2012

The Sydvaranger magnetite mine was shut down in 1996 due to low iron ore prices. It was reopened in 2009. The flowsheet has remained more or less as in the old plant, based upon two grinding steps followed by magnetic separation. The Sydvaranger magnetite is free of harmful elements and should therefore be sold on the high quality market. This requires a concentrate containing less than 2 % SiO2. In the old plant, this grade was achieved by amine flotation. Amine was preferred as collector because it could be used in process water from the sea. The use of amine has been restricted by the Norwegian pollution authorities during the time the mine was shut down. Test work to replace cationic with anionic flotation is therefore done. Research on activation of quartz with Ca or Mg ions prior to anionic flotation was shown by basic research in the period from 1960 to 1980 to be effective under simplified laboratory conditions. This old research has now been followed up from a practical/empirical point of view. The basic work was mainly done on quartz and iron minerals only. In this case, an actual feed containing a number of minerals common in iron ores is used, in order to demonstrate that a commercial process is possible. Calcium activation is shown to work excellently but requires too high pH to be environmentally and economically attractive. Magnesium activation is a more difficult process, because the maximum concentration of MgOH+, which was shown to be the activator, is about 100 times lower than the alternative CaOH+. Flotation success depends partly upon the ore, some amphibole minerals are more difficult to float than pure quartz. Ordinary batch flotation test work is time consuming. A South African microflotation test cell has shown promise, because work can be focused upon flotation of the more critical coarser fractions of the Sydvaranger ore. Keywords: iron ore concentration, anionic flotation, mineral activation, microflotation, Sydvaranger

Sep 1, 2012

By A. M. Raichur, S. P. Vijayalakshmi

Fine coal dewatering is a major problem in the coal industry because the fines hold significant amounts of water and account for two-thirds of the product surface moisture. Present methods include flocculation using polymeric flocculants followed by filtration. But the kinetics of filtration are not favorable with such flocculants. In this study, a novel method involving flocculation with microorganisms for improving the settling rates and dewatering kinetics has been investigated. Two Gram-positive microorganisms, Mycobacterium phlei and Bacillus subtilis were used as bioflocculants. The effect of time, pH and ionic strength of the electrolyte used on adhesion and flocculation were studied. Adhesion tests showed that maximum adsorption occurred in 20 minutes in the pH range of 2-7 and the total amount of bacteria adsorbed was almost the same with both the flocculants. Nearly 98% of the coal flocculated with both the microorganisms in about 5 minutes. The filtration rate of fine coal almost doubled with addition of bacteria and electrolyte and maximum filtration occurred near the point-of-zero-charge of the bacteria.

Jan 1, 2003