Search Documents

By Montaser S. EL Salmawy, Takahide Wakamatsu, Eishi Kusaka

"The effect of ethoxylation of long chain alcohols on the quartz and feldspar flotation behaviors was investigated for surfactants of the octylphenol polyoxyethylene family. The tests were carried out with an average of 7.5 (Triton X 114), 9.5 (Triton X 100), 30 (Triton X305), 40 (Triton X 405) and 70 (TritonX 705) oxyethylene units. Electrokinetic and flotation studies on quartz have shown that at low pH values, quartz could be floated with polyoxyethylene octytlphenols. The possible mode of adsorption of these nonionic surfactants may be suggested to be due to hydrogen bonding between the oxygen of ether and hydrogen in the free hydroxyl groups on quartz surface. It was anticipated that the selectivity between quartz and microcline would decrease as oxyethylenic chain length increases.Electrokinetic methods were used to elucidate the mechanism of surfactants adsorption and to correlate these findings with the optimum flotation conditions. The polymeric surfactants would reduce the negative values of zeta potential of quartz while the reverse is true for feldspar. After treatment of microcline with HCl, its electrokinetic behavior in the presence of Tritons X surfactants became similar to that of quartz.The obtained results would suggest that separation of quartz from feldspar using nonionic surfactants of octylphenoletoxylated alcohols having shorter oxyethylenic chain length at low pH could be achieved"

Jan 1, 2003

By E. N. Levchenko, K. V. Bulatov, G. I. Gazaleeva

"The article highlights the new procedure of choosing special methods of disintegration for very complicated rare ores. Especially, there is a complex approach to criteria of comparing different types of crashing machines. Criteria are as follows: degree of crashing, degree of grinding, degree of slime creation and the new creations criteria for selection. The procedure is tested on tantalium and zelestinium ore. A new methods was shown the preference impact crashing machine MD-7 for zelestinium ore. In product of crashing 0,050 mm size are 9.4 %, 0,005 mm size – 2.5 %.This is gut result, and show the best indexes of slime creation. The check of the proposed new methods was done when comparing the crushing of tantalium ores of the Otboynoe deposit in cone inertial and centrifugal impact crushers and roller press. A research was conducted different crashing machines under laboratory and semi-industrial conditions. Different operation modes of crushers were also checked. The comparison of the crushing selectivity criterion and degree of crashing showed that the centrifugal impact crusher (CC) and roller press (RP) has the lower indexes than the cone inertial crusher (CIC). Degrees of crashing for different crashing machines are:centrifugal impact crusher – 10.1;roller press – 10.8;cone inertial crusher – 14.2. The crusher CC the selection criterion is 0,632 units, RP – 0.730, where as for the crusher CIC – 0.848 units. The best crushing mode for the crusher CIC-300? is as follows: turning angle of debalance is 0°, peripheral speed of a cone rotation – 1420 r.p.m, specific energy consumption- 4.99 kW*t/t. Crusher CIC-300? is the best for tantalium ores of the Otboynoe deposit. The new methodic are verification.INTRODUCTION Rare metal concentration circuits are complex, energy-intensive, and costly. The reasons for this include the multimetal nature of the rare metal ores, their volatile material composition and low grade. That is why careful selection of ore preparation circuits is of great importance for minimizing the energy inputs and maximizing the liberation of the valuable minerals. Recent research (Khopunov, 2011, Gazaleeva, 2015) has demonstrated that the most efficient comminution processes available to the mineral processing industry are selective disintegration, crushing and grinding, allowing to liberate the mineral particles along the cleavage in the comminution process. These methods are indispensable for the processing of finely disseminated refractory ores prone to slime formation. Many rare metal ores found in Russia are of this type."

Jan 1, 2018

By Wei Sun, Chengwei Li, Zhiyong Gao, Yuehua Hu

"Grinding for mineral liberation is a prerequisite for a successful flotation separation. Different grinding media produce mineral particles with different morphologies and surface properties. In this study, the surface physicochemical properties of fluorite particles produced by ball and rod mills were systematically investigated through single mineral flotation experiment, wettability measurement, X-ray diffraction (XRD) test and scanning electron microscopy (SEM) observations. The XRD observations reveal that the surface exposure degree for both mill particles follows the order {111} > {110} > {100}. The difference lies in that the rod mill ones have a higher exposure of more reactive {110} and {100} surfaces, leading to a stronger interaction with the collector. The difference also leads to their higher elongation and lower roundness values of rod mill particles which are beneficial for the particle-bubble attachment by shorting the induction time. The wettability and flotation results show that the rod mill ones have a lower critical surface tension and a greater hydrophobicity when treated with the collector solution and accordingly perform a higher flotation recovery. This work, for the first time, revealed the importance of the exposure of crystal surfaces in determine the shape factors and reactivity of the mineral particles and will help provide guidance for optimizing flotation separation and particle surface modification. INTRODUCTIONFluorite (CaF2) is the most important source mineral for producing F-based chemicals and materials which are widely used in industrial, environmental, and medical fields [1, 2]. In ore deposit, there are two kinds of occurrence forms of fluorite mineral. Firstly, the fluorite mainly coexisted with the gangue minerals like calcite (CaCO3) and quartz (SiO2). Because of their similar density and fine-grained dissemination in ore deposit, ball mill grinding before flotation separation has been widely applied to produce relatively fine particles [3]. Secondly, the fluorite is often associated with other valuable minerals with higher relative density such as scheelite (CaWO4) and cassiterite (SnO2). Due to their obvious density differences and coarsely grained distribution in ore deposit, rod mill grinding before gravity separation has been usually used to produce more uniform particles and avoid over-grinding [4-6]. After the gravity separation, a flotation separation is also employed to beneficiate the fluorite [7]."

Jan 1, 2018

By Yuexin Han, Wenbo Li, Yan Shan, Yanjun Li, Shumin Zhang

"With the accelerating pace of resource extraction, the quality of resources is decreasing, and the old tailing dams which have served for several decades have become the focus of attention. The secondary recovery of valuable metals in the tailings is an important aspect of the comprehensive utilization of tailings. The average iron content of iron tailing is 8%-12% in China. The research aimed at exploring the low-cost and efficient technical route to recycle eastern tailings of Anshan iron mining area. The purpose of the research is to scientifically find the rational conditions of magnetizing roasting and to provide an increase in recovery and quality of concentrates. The eastern tailings of Anshan mining area belong to high silicon bearing iron tailings, iron mainly exists in form of hematite-limonite with an iron grade of 10.60%, the main component of gangue is SiO2 with a grade of 76.22%. In order to reduce the influence of the tailings on the environment, fluidized magnetizing roasting and low intensity magnetic separation for the eastern tailings of Anshan mining area were carried out to improve the utilization of the tailings. The results indicated that an iron concentrate with an iron grade of 65.30% and a recovery of 85.85% could be obtained under the conditions of gas flow rate 8 m3/h, H2 concentration 50%, fluidized magnetizing roasting temperature at 600? for 20s. Phase analysis, magnetism analysis and XRD analysis on roasted materials indicated that hematite-limonite could be transformed to magnetite during the fluidized roasting, then the effective separation of iron and gangues could be made easily by the weak magnetic separation. INTRODUCTION It is universally acknowledged that the grade of iron ore in China is low, the output rate of iron ore tailings is high, usually more than 60%. At present, the comprehensive utilization rate of iron ore tailings is low in China. Generally, the iron ore tailings are stockpiled in the tailings dam. The tailing dams not only occupy a lot of land, but also takes a lot of money to construct and maintain. In addition, the noxious substances in the tailings, such as residual flotation agents and heavy metals, have a severe impact on the ecological environment. There is little doubt that tailing dams have a visual impact on the environment due to their regular geometric shape. Iron tailings can be treated as compound mineral, which is an important component of comprehensive utilization of mineral resources, and is an has been widely concerned. Lots of scholars have done a large amount of research work on a large number of iron ore tailings. Since the iron mineral crystal grain size is fine and the iron grade is low, the iron tailings have failed to achieve good selection criteria."

Jan 1, 2018

By L. Y. Wang

In order to produce the iron and steel products with high quality and decrease the output of steel tailings, the quality of molten iron is a critical factor for iron and steel companies, especially the content of sulfidic in molten iron. Hot metal pre-treatment, an important and effective method to desulphur, is widely used in steel production. Millions of tons of slag from desulphurization and slag skimming are produced each year in China, and many more times this amount is stored in slag dams because of the lack of effective means to deal with it. In order to achieve the goal of sustain-able development, recycling these slag becomes necessary. The main objective of this paper is to study the composition characteristics of slag that from desulphurization and slag skimming. The sample was obtained from Anshan Iron and Steel Group Corporation, processed by hot metal pre-treatment. In this study, the chemical components and the mineral compositions of sample were tested. The results of chemical components and iron chemistry phase analysis showed that the iron and sulphide content in this sample were high, and the iron products existed mainly in the form of magnetite, metallic iron, ferrosilite. X-ray diffraction (XRD) and scanning electron microscope (SEM) results indicated that the sample included metallic iron, ferrate, wustite, metasilicate, aluminate, aluminosilicate, white lime and soon. Grading magnetic separation test work showed that magnetic separation was an effective method to recovery iron products and decrease the sulphide content in concentrate, and the tailing could be used as the raw material or padding in cement production.

Jan 1, 2014

By Bruce Mathema, Steven Huynh, Terry Cheng, Gerry Gomez

"The use of PM40N, a specialty precious metals promoter in conjunction with a standard Xanthate based collector was extensively investigated in the flotation of a complex, silver-bearing, lead-zinc ore containing naturally occurring graphitic gangue. The ore, considered difficult to treat with conventional reagents, was tested at plant scale to determine the impact of the promoter on silver recovery, lead grade and also on the amount of zinc misplaced to the final lead concentrate.Initial laboratory-scale rougher flotation testing implied significant improvements in the recovery of silver and lead with a marginal amount of zinc displaced. Subsequent mini pilot flotation tests further revealed that a gain in selectivity and recovery could be achieved by adjusting PM40N promoter dosage and incorporating a cleaner flotation step, further improving rejection of sphalerite. Plant trials resulted in an improvement of 3% in Silver recovery coupled with a 2% increase in recovered lead whilst maintaining lead grade in the lead circuit.To date, the use of PM40N as a promoter has enabled the processing operation to significantly increase its plant economics. The partial replacement of the standard Xanthate based collector has also reduced the overall quantity of Xanthate required in the standard circuit by approximately 10% - which is a positive impact on the environment. It is envisaged that further optimization of plant parameters will favor stable operation and continue to boost revenues generated by subsequent improvements in silver metallurgy."

Jan 1, 2014

By Y. S. Sun, P. Gao

Compared with conventional roasting and magnetic separation processes, higher reduction temperatures and stronger reducing atmospheres are used in reduction technologies to reduce iron oxides to metallic iron, which is often liberated during reduction and amenable to magnetic separation. Reduction and magnetic separation of an Australian refractory iron ore was therefore studied as a function of reduction temperature, time, coal addition, feed thickness and size of Australia iron ore. It was found that during reduction, the particle size of the reduced iron increased with reduction temperature and time. Subsequent magnetic separation tests were further conducted on the reduction products. A reduced iron powder with a Fe grade of 85.67% was obtained at a Fe recovery of 87.82% under optimum reduction conditions where a metallization rate of 85.82% was achieved. The mechanism involved in reduction is discussed based on XRD and SEM examinations. And the results indicated that theiron minerals such as hematite and limonite in the Australian iron ore were reduced as follows: Fe2O3?Fe3O4?FeO?Fe. Furthermore, the metallic iron particles produced by reduction increased in size with longer reduction times.

Jan 1, 2014

By L. Bbosa

Positron Emission Particle Tracking (PEPT) and the Discrete Element Method (DEM) are used to investigate Power Draw in a laboratory scale tumbling mill. The mill is run dry in batch mode at different speeds using mono-size charge of glass beads, and is mounted along with a torque transducer to measure power. Particle tracking information from PEPT is used to reconstruct the motion of glass beads and infer the overall charge behavior, while DEM is employed to simulate particle motion and interaction, with collision mechanics calculated using the Hertz-Mindlin contact model. For PEPT and DEM data, the product of torque and average angular velocities in discrete cells are accumulated to obtain mill power. This method is found to be within statistical agreement with measured power for all tests. Spatial distributions plotted from this approach highlight the regions of the mill that draw the greatest power. A second technique to obtain Power Draw from DEM data which sums particle forces against the mill geometry is similarly found to accurately predict mill power with lower statistical error. Keywords: Power Draw, PEPT, DEM

Sep 1, 2012

By Ataollah Nosrati

Agglomeration of fine mineral particles is an important step in heap leaching processes employed for a cost-effective hydrometallurgical extraction of value metals from low-grade ores. In this study, the effect of acidic binder composition and feed ore particle size on binder dosage requirement and isothermal, batch agglomeration behavior of siliceous goethite nickel laterite has been investigated. Agglomeration tests performed with tap water and 30, 44 and 98% w/w H2SO4 solutions as binders revealed the key role of binder formulation in controlling ore particle wettability, nucleation and granule growth behavior. Both lower binder acid content and higher dosage led to greater wetting, nucleation and granule growth rates. Variation of feed ore fine/coarse particles? mass ratio dramatically impacted on binder dosage requirement for effective particle wetting, nucleation, and growth agglomeration behavior. Increasing fine (-150 µm) fraction mass content in a -2 mm feed ore, led to higher binder dosage requirement and enhanced nucleation, however the overall agglomeration rate/granule size growth decreased. In contrast, the presence of coarse (5 ? 15 mm) particles in feed ore led to (i) lower binder dosage requirement, (ii) enhanced initial agglomerate size growth rate, and (iii) reduced coalescence. For dry agglomerates of similar sizes, competent coarser feed particles led to remarkably higher compressive strength than did finer feed particles. Microstructure analyses indicated that the granules containing coarser particles exhibited a distinctive, competent core/shell (fines) structure which led to their structural reinforcement. The appropriation of the findings for optimizing agglomeration behavior for enhanced heap leaching of complex, low grade laterite ores are discussed in this context.

Sep 1, 2012

By Dmitriy Makarov

The paper presents the modeling and analysis of oxidation of pyrite copper-zinc ore samples from the Letnee, Yaman-Kasy and Valentorskoye deposits. It is found, that the oxidized samples contain copper and zinc sulfates that are leached under the sample and water contact. It is shown, that sulfide floatability is decreased by the longer-term oxidation.We advise to improve nonferrous metals recovery by joint leaching and ultrasonic treatment of oxidized compounds. Study of the geotechnological processes of non-ferrous metal extraction, on the basis of two copper-zinc ore deposits shows, that heap leaching is of little use for the ores of the Letnee deposit. Leaching results for the Yaman-Kasy ore showed more promise.

Sep 1, 2012

By G. Sedelnikova

This paper is aimed to elucidate the problem of copper losses in pyrometallurgical slag. Currently, flotation is used to recover copper from the slag and return the metal into the pyrometallurgical process, but the percentage of recovery frequently remains unacceptable. The process of copper leaching from the slag flotation tailings using biologically regenerated ferric sulfate is considered here as an approach to the issue. A sample of the slag flotation tailings containing 0.67% Cu and 4.99% Zn was supplied by the Urals Mining and Metallurgical Company (UGMK, Russia). The Cu and Zn speciation analysis of the sample demonstrated that Cu occurred as 58.1% oxide, 15.4% native Cu, and 18.1% secondary sulfides whereas chalcopyrite proportion was as low as 8.4%. Prevailing Zn species were refractory (58.9% Zn ferrite), and zinc oxide and silicate species made just 37.2% of the total metal content. The silicate generated silica gel that strongly hampered filtration. As demonstrated, Cu recovery is a possibility, which is apparently not the case with Zn. In this work, the stirred tank bioreactor acid leaching employing bacterial Fe3+ sulfate solutions was studied, with ferric sulfate being a product of Fe2+ biological oxidation and not the chemical reactant adding of Fe3+ sulfate. Acidithiobacillus, Sulfobacillus, and Leptospirillum bacilli were employed in Fe2+ biooxidation. Temperature, pH, Eh, S:L ratio, leaching time, and Fe3+ concentration in the source leachate as the process controls were considered. As demonstrated, the process employing biologically regenerated ferric sulfate proved to be more efficient than conventional chemical leaching. Under the optimum conditions, the proportion of Cu extracted into leachate during 2 hours was 79.1%, and that of Zn 27.2%. Precipitation of high-grade Cu sulfide served to extract the metals from the leachate, and Cu extraction was 99.7%. All in all, 23.2% Cu, 0.03% Zn, and 0.02% Fe was returned into the pyrometallurgical process. Keywords: slag flotation tailings, copper leaching

Sep 1, 2012

By V. Panayotov, M. Panayotova

"Wastewater from ores processing is often polluted by molybdate and sulfate (SO42-) ions. Sorption is one of suitable methods for removing those pollutants when presenting in low concentrations. This work reports results on adsorption of sulfate and molybdate ions on metal modified (with barium - Ba and lead - Pb) and organic reagent modified (with Hexadecyl-trimethyl-ammonium bromide - HDTMA) clinoptilolite. Zeolite’s modification with Pb, Ba and HDTMA increases its uptake capacity with respect to Mo(VI) at pH 3, with the uptake capacity decreasing in the order CL-Pb > CL-HDTMA > CL-Ba. Lead-modified clinoptilolite shows high uptake with respect to Mo(VI) in acidic, neutral and slightly alkaline conditions. The presence of SO42- in concentrations twice higher than the amount of Mo(VI) do not interfere with the Mo(VI) removal by CL-Pb. Zeolite’s modification with Ba and Pb renders it able to immobilize SO42- from water in the pH range 3-9. Kinetics of the uptake process is best described by the pseudo-first order kinetic equation. Increasing the initial concentrations of Mo(VI) and SO42- increases the removed amount of pollutants. INTRODUCTION Wastewater from copper-molybdenum ores processing is often polluted by molybdate and sulfate ions. Molybdenum (Mo) migrates easily in water and consequently the Mo polluted areas could extend for hundreds and thousands of meters (Ryzhenko, 2010). Molybdate anion is the only Mo(VI) species in natural water, i.e. at pH > 6.0. Its median freshwater hazardous concentration affecting 5% of the species (HC 5.50%) is 38.2 mg Mo/L (De-Schamphelaere et al., 2010). The marine water chronic toxicity (HC 5.50%) is assessed at 5.74 mg Mo/L (Heijerick et al., 2012). The predicted no-effect concentrations (PNEC) are 12.7 mg Mo/L and 1.92 mg Mo/L correspondingly for freshwater and marine water (Heijerick et al., 2012a). When sulfates present in drinking water in excess of 250 mg/L they cause a cathartic action (especially in children) in the presence of sodium and magnesium, and when the concentration exceeds 600 mg/L, diarrhea. When sulfate-rich effluents are discharged into the environment, they may increase the acidity of water bodies and soils (Guimarães and Leão, 2014). Because of the adverse effects to human health and the environment, limits are set for SO42- concentrations in waters and wastewaters in the range of 250 / 500 mg/L."

Jan 1, 2018

By T. Niedoba

The ash contents in coal particles were examined in the paper dependably on particle size and its density. So, the two-dimensional regressive function Z=Z(?, D) was the searched object, where Z is random variable describing ash contents, ? - density and D ? particle diameter. This dependence is determined basing on experimental data concerning the coal of type 31. For this coal, the method of ordinary kriging is applied to calculate the values of a random variable Z. This method requires the proper selection of so-called variogram function, which 4 forms are considered in this paper in purpose to select the best solution. The given results were then evaluated by the residual deviation value and so compared with empirical data.

Sep 1, 2012

By A. I. Urvanzev, N. V. Shikhov

"In this paper, we present the study’s results of electrical separation processes on the basis of new separator designs, new technological solutions, and newly discovered effects. We considered the options of enrichment by magnet separation of magnetite and titanomagnetite ores, ores and products containing chromium and manganese, ores of non-ferrous and precious metals. During pneumo-electric separation of mixed iron ore of SMPC, 43.3% of the output of the concentrate with an iron content of 61.7% was obtained in one step, with extraction of 70.5%. The paper also presents the results of the finalization on the air-electric separator of the magnetic fraction when separating oxidized ores of MPPOO (mining and processing plant of oxidized ores) on the Jans polygrade magnetic separator. A concentrate was obtained with an iron content of 65.1% with the extraction of 95.0% and tails with an iron content of 13.0%. The possibility of obtaining low-silica concentrates from these ores with an iron content of 67.15 and a quartz of 2.88% is shown. Also, the results of tests on the enrichment of chromite ores on the firing-magnetic scheme with corona-electrostatic separation are considered. On the initial ore of the Don MPP (mining and processing plant), a concentrate with a content of 61.8% Cr2O3 was obtained with a quartz content of ~ 1.0%. The results of pneumo-electric separation with triboelectric charge of the separated particles are presented. The results of the tests indicate a principal possibility of enriching chromite ores without costly high-temperature roasting. Dry technology of enrichment of manganese ores with the use of electrical separation increases the quality of the oxidized concentrate to the first grade and raises the total extraction by 2 times. For the Chineya deposit of titanomagnetite ores with copper impurities, electroseparation operations were carried out on two samples with a Cu content of 1.93 and 3.75%, respectively. For a sample with a Cu content of 6.02%, a copper concentrate output of 24.42% was obtained with a Cu content of 23.82% and the extraction of 94.88%. The results of enrichment by electroseparation of gold-containing sulfide ores can have the practical importance. For ores of the Berezovskoye deposit, a pyritic concentrate containing 100 g / t of gold was obtained after two or three operations of IES (integrated energy systems)."

Jan 1, 2018

By Z. G. Song, C. Y. Sun, X. R. Zhang, Y. Yu

In skarn type scheelite deposit, there are calcium minerals with floatability similar to scheelite, such as calcite, fluorite, etc., which are difficult to separate. Heating cleaning method developed by Petrov has been widely applied in processing rough concentrate of scheelite for nearly half a century, but there exists a general lack of full understanding of the interaction between floatation reagent and mineral particles surfaces. The mechanism on separation of scheelite and calcium minerals in heating cleaning process was investigated by mineral flotation experiments, XPS analysis, as well as solution chemistry and crystal chemistry calculations. The results showed that the sequence of minerals floatability using sodium oleate as collector and a large amount of sodium silicate as modifier in heating flotation test was scheelite > calcite > fluorite, which was the same as solution chemistry calculations based on Gibbs free energy vs. pH and also the same as Ca-X intensity order by crystal chemistry analysis. There are two sides about the mechanism of heating cleaning method: one is that the adsorbed collector on calcium minerals surface is desorbed more easily than scheelite, and the other is selective dissolution of calcium ions from the mineral surface because of Ca-X intensity difference in heating and stirring process.

Jan 1, 2014

By Kym Runge, Wei Huang, Fengnian Shi, Christian Antonio

"This paper presents an emerging High Voltage Pulse (HVP) technology for ore pre-treatment. Unlike previous studies where HVP was utilized as a crusher to pulverize ore particles to micron size ranges for downstream processing, the researchers at the Julius Kruttschnitt Mineral Research Centre (JKMRC) use HVP to enhance ore processability. Application of relatively low levels of HVP energy to selectively break mineralized particles from barren rocks, followed by size-based screening separation enables the feed ore to be split into high grade and low grade products. During HVP treatment, cracks/micro-cracks are generated which results in pre-weakening of the treated ore particles, which ultimately results in energy savings in the downstream comminution processes. HVP treatment followed by conventional grinding also results in improved liberation of the valuable minerals in comparison to that achieved with traditional conventional comminution, subsequently improving downstream separation efficiencies. The three major improvements in ore processability through HVP pre-treatment have the potential to facilitate rejection of low grade ore prior to processing, increase production rates, reduce the energy required for comminution and improve flotation separation recoveries. This paper summarizes the major research outcomes of HVP pre-treatment demonstrated using ores from various mining operations conducted by the JKMRC. It also discusses the barriers that must be overcome before it can be adopted by industry with confidence in a continuous high tonnage rate application.INTRODUCTIONThe challenges of declining ore grades and increased plant throughput rates, resulting in higher energy consumption and operational costs, require the mining industry to adopt new technologies to make future ore treatment economically viable. Over the past 50 years, many researchers have engaged in investigating novel comminution techniques. Since Yutkin (1955) first demonstrated the potential to generate shock waves with pressures exceeding 103 MPa via electrical breakdown of water, several applications of electrohydraulic crushing by shock waves have been reported (Curley-Macauly, 1968). Interest in this technique was bolstered when Andres (1977) demonstrated that electrodynamic fragmentation results in superior liberation of mineral grains as compared with conventional grinding techniques. Despite mounting laboratory-scale evidence of the efficacy of electrodynamic fragmentation for mineral liberation, development of the technology for full-scale operation has stalled, primarily because the energy required to achieve desirable mineral liberation is approximately two to three times that of mechanical comminution, amounting to approximately 100 kWh/t for typical mineral ores (Andres et al., 2002)."

Jan 1, 2018

By L. Gao, X. Gui

Fine coal obtained from Kailuan mine served as the processing object of this study. This material was difficult to separate. A flotation rate experiment was designed to investigate the process distribution characteristics of size and density during fine coal flotation. Size and density analyses of five clean were studied. The mineral morphology of flotation rate experiment cleaning was observed through scanning electron microscopy. The fractions -0.074+0.045 mm and -0.045 mm exhibited the best practical floatability and presented the highest combustible body recovery rates, but the selectivity and natural floatability of these two fractions were the worst. The - 0.074 mm fraction has contaminated the clean coal from the early stage of flotation, and the cumulative clean coal ash of -0.074 mm reached up to 17.20%. The low and middle-density classes displayed varying flotation behavior, but the flotation yield difference was only nearly 3%. The middle-density class caused the clean coal to have high ash content. The poor selectivity of fine coals, middle-density fraction, and fine mud resulted in high-ash clean coals during flotation. Thus, improving the selectivity of fine coal, restraining the flotation of fine mud, and grinding the coal to decrease the middle density mass fraction to liberate clean coals can yield high-quality clean coals through flotation.

Jan 1, 2014

By S. H. Morar

Froth flotation is a physico-chemical separation process that takes place in two phases; pulp and froth phase. It is widely recognised as a complex process, due to the range of interactions present within the system. Of critical importance is the role of the froth phase within the system. The pulp kinetics governs the maximum potential recovery within a flotation cell, while the froth phase governs the selectivity via the froth?s stability. Higher froth stability improves recovery at the expense of grade, and lower froth stability improves selectivity. It is well known that the two major factors affecting froth stability are attached particles and solution chemistry. This paper looks at a flotation bank at different froth depth and frother concentrations. The air recovery to the concentrate is determined at each condition and relates the effect of the operating conditions on froth stability and transport to the amount of solids that are recovered to the froth and concentrate by true flotation. The results presented show that, for a given process objective, which in this case was a consistent mass pull profile, depending on the operating conditions, solids recovery in the pulp is affected by the air rate required to maintain the target mass pull. To a smaller extent, the changes in the pulp composition affect down-stream pulp recovery. The variation in solids recovered into the froth drives the froth stability at the start of the flotation bank, while the frother drives the froth stability at the end of the bank. The performance in between these two extreme conditions arises from an interaction of these two effects. The consequences of these interactions can give rise to counter-intuitive responses that can confound efforts to optimise the performance of the bank.

Jan 1, 2014

By I. S. M. K. Ilankoon

In heap leaching the transport of the acid from the drippers to the surface of the ore particles is a major factor in the overall performance of a heap. This flow behavior is complex as the flow is unsaturated and occurs along a tortuous set of inter-particle channels and connections. Previous modeling of this system has used equations from oil and ground water flow to model these systems, but the applicability of these models with the larger particles found in typical heaps is suspect as these systems are not necessarily capillary dominated. In particular, as the characteristic particle size goes from below to above a few centimeters, the flow changes from capillary to gravity dominated. This means that typical heap leaching heaps cover this interesting, but complex, transitional fluid flow regime. In this paper a set of experimental studies of this flow, including PEPT (positron emission particle tracking) based tracer experiments, highly accurate liquid holdup measurements and axial dispersion experiments using salt tracers will be presented. In this study, flow through mono-dispersed particle beds was carried out. In particular, the hysteresis in the liquid holdup as the liquid flow rate into the particle bed is varied is investigated, since this hysteresis means that the relationship between flow rate and holdup is history dependent, an effect not included in models currently used to describe fluid flow in heaps. A theoretical model that describes this hysteresis will also be presented. Keywords: heap leaching, hydrometallurgy, modeling

Sep 1, 2012

By S. Jeon, N. Hiroyoshi, N. Kitajima, S. Tanaka, M. Ito, R. Pongsumrankul, C. B. Tabelin

"Gold (Au) extraction is inefficient when crushed waste mobile phones (WMPs) are directly leached by ammonium thiosulfate likely because of the cementation/precipitation of dissolved Au in the presence of base metals like copper (Cu), iron (Fe) and/or aluminum (Al). This study applied physical separation techniques to remove base metals as well as plastics and concentrate the Au containing fractions from WMPs prior to leaching. Coarse fraction of crushed WMP (+2-5.6 mm) was pretreated by jig and magnetic separation to remove plastics and base metals like Fe, Cu, and Al, while the fine fraction (-2 mm) was pretreated by flotation, and float and sink separation. The leaching results showed that Au extraction increased in both of the size fractions. In the coarse fraction, Au extraction increased by as much as 2-fold after pretreated (from 4 to 7%). Improvement of Au extraction in the fine fractions after pretreatments were even more dramatic. Au extraction increased from 4 to 61%. These results indicate that physical pretreatment to remove co-existing common metals and plastics is effective to improve Au extraction from WMPs. INTRODUCTION Global sales of mobile phones are expected to increase steadily in the foreseeable future because a lot of people buy newer phones with upgraded and more advanced functions almost every two years, which leads to the higher generation of waste mobile phones (WMPs). WMPs contain a wide variety of materials including plastics, glasses, base metals and precious metals such as gold (Au). Among all the valuable materials in WMPs, Au accounts for over 80% of its total metal price (Park et al., 2017), so recovery of Au from WMPs is needed."

Jan 1, 2018