Search Documents

By Mary Ellen Bruce Large, Antonio Marinucci, Silas C. Nichols

Tip post-grouting of bored pile (drilled shaft) foundations refers to a method where cementitious grout is injected beneath the tip of a shaft to improve the overall performance of the constructed foundation. This technique, when performed satisfactorily and in the appropriate ground conditions, enhances axial load-displacement performance by improving the mobilization of pile’s resistance. Potential benefits associated with tip post-grouting include reduced settlement under loading, better alignment of load transfer curves, and improved ground beneath the base of the bored pile. However, to be able to realize the benefits attributed to this method, the design, construction, of both the bored pile and the post-grouting system must meet a minimum level for quality assurance. The various factors affecting the successful installation and performance of a bored pile (e.g., workmanship, base cleanliness, borehole integrity, and concrete placement) have been discussed by numerous practitioners and researchers in the available technical literature. For a conventional (i.e., ungrouted) bored pile, acceptance is based on a combination of visual inspection, material testing, and the results of integrity and/or performance testing of the constructed pile. A properly executed tip post-grouting program can be a relatively comprehensive and complex process, which is typically evaluated throughout the construction process based on the results of prior projects and/or on test pile(s) at the particular site. For tip post- grouting programs, verification procedures and acceptance criteria should be established during and incorporated into the design process to ensure design intent and objectives are achieved. Project specifications should be produced to ensure performance requirements are achieved. This paper will present and discuss factors affecting the successful execution of tip post-grouting, including grouting criteria, instrumentation, reliability and uncertainty with the method and outcome, and verification and acceptance. INTRODUCTION Constructing bored piles (drilled shafts) is increasingly more challenging given the lack of ideal site locations, tight project site confines, difficult or restricted access, greater demands on drilling equipment, and close proximity to adjacent structures. To evaluate the feasibility of bored piles as an appropriate foundation system, a myriad of factors is evaluated during design, including site conditions and constraints, budgeting and scheduling, reliability and risk exposure, presence of and depth to adequate load bearing soils/rock, and the magnitude of the imposed loading. Moreover, updated design codes increased load demand per element, and improved material strengths have led to more complex foundation designs, larger foundation elements, and significant increases in load magnitude. Monopile (monoshaft) foundations have been utilized where one large bored pile is used in lieu of a group of piles connected via a pile cap. In addition, to accommodate the design criteria, site conditions, and imposed loading, the geometry of the bored piles being designed and installed have been as large as 13 feet (4 m) or greater in diameter and to depths in excess of 260 feet (80 m).

Jan 1, 2018

By C. Van der Veen

The use of the quasi static (Dutch) Cone Penetration Test (CPT) is described as a tool to predetermine the ultimate bearing capacity of the pile point. An analysis is given why a purely theoritical approach does not meet with success. A practical method is explained of extrapolating the cone resistance to predict the pile point resistance. The method has been calibrated against the result of 32 selected high standard loading tests on pile points in the Netherlands.

Jan 1, 1989

By David B. Paul

"ABSTRACTThe US Army Corps of Engineers (USACE) has 704 dams in their inventory and over 100,000 miles of levees with a capital value of over $150 billion. Currently, there are 319 dams that are classified as high hazard and have actionable failure modes that will require structural modifications. The most frequent actionable failure mode associated with the inventory is seepage and piping. One of the most effective engineering solutions is the installation of a cutoff to limit seepage. Currently, USACE has over $1.5 Billion of cutoff wall projects under construction and/or design. Given the magnitude of the dam and levee safety issues, USACE is developing a new Engineering Manual (EM) titled “Seepage Control Cutoffs for Dams and Levees.” This EM covers all of the methods to construct cutoff walls. USACE has partnered with the Deep Foundation Institute (DFI) in preparation of the EM to ensure that it is comprehensive and draws from the expertise of the specialty foundation engineering companies that design, manufacture, and construct seepage control cutoffs around the world. The EM contains case histories as well as a comprehensive project statistical summary and guide specification paragraphs. The goal of USACE was to make the EM a state of the art document for use by Districts.HISTORYSlurry wall construction techniques were developed in the late 1940’s in Italy by ICOS. The first use of the slurry trench method of construction in the United States was by the USACE Memphis District in September 1945, to form a partial cutoff along the Mississippi River levee on the Arkansas side of the river just below Memphis, Tennessee. The idea for the project probably evolved from the use at that time of puddle clay trench cutoffs combined with the use of drilling mud for advancing borings. A paddle wheel mixing device was constructed for making slurry from native clays. Trenches were dug to a 20-ft depth using a trenching machine and to a 35-ft depth using a dragline with a 100-ft boom and 2-cu-yd bucket. Backfill was mixed in windrows at the site from hauled-in clay gravel and native materials and pushed into the trench by a bulldozer when the length of the trench was equal to about twice the trench depth. It is amazing that after almost 70 years, the technique is still about the same as it was when first developed by the Memphis District. A soilbentonite cutoff was constructed under the Kennewick Levee adjacent to the Columbia River as part of the McNary Dam Project in Washington by the Walla Walla District in 1952 The first application of a soil-bentonite slurry trench cutoff for control of underseepage at a major earth dam was at Wanapum Dam on the Columbia River in Washington in 1959.The first cement- bentonite cutoff in the United States was constructed at the Tilden Tailings Project to store tailings from the Tilden Mine in Michigan in 1976. The first cement-bentonite cutoff constructed at a dam on a river retaining a reservoir in the United States was completed in 1978 at the Elgo Dam (formerly the San Carlos Dam) in Arizona.The USACE has designed and constructed some of the deepest and most complex cutoff walls for dams since the 1970’s. The first major concrete panel cutoff wall constructed in a dam in the United States was at Wolf Creek Dam (Nashville District) by the ICOS Corporation between 1974-77. The dam has a long history of seepage issues associated with the karst geology that comprises the foundation. In 1968, about 17 years after first being impounded, wet areas, muddy flows in the tailrace and sinkholes in the downstream toe adjacent to the switchyard occurred."

Jan 1, 2014

By H. Boghosian

This paper presents the design and construction of a deep basement in a steeply sloping site in glacial till in Glasgow city centre. Existing foundations, adjacent structures and services, in tandem with asymmetric loading, presented particular challenges in the planning, execution and design of the project. The construction methods and temporary works, analysis by the Finite Element method and monitoring carried out are all described.

Jan 1, 2006

By William Babcock

Augered, Cast-In-Place (ACIP) piles can be an economical, reliable, versatile foundation system. They have also been a part of projects that were behind schedule and the subject of lawsuits. The ACIP pile is a specialty system that is more workmanship dependent than most deep foundation systems and is especially vulnerable to the problems and abuse of poor specifications and contract language. Many of the original specifications were based on grouting methods, and numerous misconceptions have followed the method. The Deep Foundations Institute (DFI) has been the leader in debunking the mystique that has hovered over the method and attempted to standardize the industry through publication of the manuals describing the method and how it should be inspected. DFI should be applauded for taking the lead and producing a reference document that can be used to educate the specification writers, designers, inspectors, and owners. It must be must appreciated that there have been other organizations that would not acknowledge ACIP piles as a legitimate member of the deep foundation family. Some consultants and designers have gone to the extreme of making it policy to not recommend the method for use. This presentation is one practitioner's view of the causes of problems as they can be traced back to the contractual conditions. It is intended to provide a broader and different perspective than those provided by the technical specialists. It does not necessarily reflect the position of the DFI or any of the organizations associated with the ACIP pile industry. It is intended to further the spirit of partnering on every ACIP pile project, to further the acceptance and promote the use of this unique system, for the benefit of all the parties. It should be recognized, however, that all of the participants can and do play a role in getting a project into trouble. My view is that projects that get into trouble usually have an early flaw that leads the project to the edge, and the project participants blindly follow the original mistake right over the cliff like lemmings. This instinctive reaction may be a survival tactic by going along with the group, because any one party that departs from the program or shows a position of weakness is a candidate for sacrifice.

Jan 1, 1997

By Anne Lemnitzer

Full-Scale cyclic field testing was performed on a 3x3 pile group consisting of nine cast-in-drilled-hole (CIDH) reinforced concrete shafts and a comparable single-shaft in order to investigate group interaction effects. Both specimens were constructed with pile diameters of d = 0.61m (2 ft), fixed head boundary conditions, and placed in stiff clayey soil at a test site near the LAX Airport in Southern California. Internal instrumentation was installed in the single pile as well as in three piles within the pile group to obtain pile curvatures. External instrumentation controlled the lateral displacement of the specimens. A combination of experimentally and analytically obtained p-y curves for the single pile was used to simulate results for piles located in the group when field data were not available. All test specimens were tested to structural failure and excavated after test completion to investigate pile damage and plastic hinge formations. Calculated group interaction factors ranged between 1.0 at very small displacement levels of <2.5 mm (0.1 in), 0.8 at the initiation of the pile-soil-pile interaction, i.e. between 4 mm - 15 mm (0.16-0.6 in), and increased towards 0.9 near structural failure (displacement >25 mm or 1 in). A literature set of p-multipliers was found to reproduce an accurate fit to the available load displacement test data from the group.

Jan 1, 2010

By Christian Besson

This article describes the implementation of a new jointing process for use between diaphragm wall panels. This process was initially introduced on the SOCATOP work site in uburban Paris (which involved the closing of the western section of the A86 bypass road), on a tunnel ventilation shaft. This brand new system upgrades the potential offered by other types of joints available and enables both ensuring the continuity of panels for structures over 40 m in depth under the strictest safety conditions and constructing shafts with diameters of less than 15 m. A patent for this process has recently been filed.

Jan 1, 2002

By Masaki Kitazume, Yoshiaki Kikuchi

"Abstract Pile foundation is one of fundamental techniques to improve the bearing capacity and settlement characteristics of superstructures. Wide varieties of piles having various shape, size and material were developed and have been applied to a lot of construction projects throughout the world. The deep mixing method, an in-situ admixture stabilization method, was developed in 1970s in Japan and the European countries, and has been frequently applied to many construction projects for various improvement purposes such as increasing bearing capacity and horizontal resistance, reducing ground settlement, preventing liquefaction and so on. The design methods, execution procedure and quality control and assurance (QC/QA) of the method are standardized or specified in many countries. These standards, specification and/or technical manual have been a remarkable contribution to spread the techniques throughout the world. The QC/QA is one of the major concerns for clients and engineers who have poor or no experience of the technologies. In order to assure the high quality of deep mixing work in the global market, it is necessary to establish the concept of QC/QA and correlate the output of different procedures. Upon the request by the organizing committee of the DFI-EFFC International Conference on Piling & Deep Foundations, the authors conducted survey of the specifications and standards on the piling and deep mixing technologies in Asian countries. In this manuscript, the results of survey are briefly introduced by comparing these specifications and standards.IntroductionThe pile foundation is one of fundamental techniques to improve the bearing capacity and settlement characteristics of superstructures. Wide varieties of piles having various shape, size and material were developed and have been applied to a lot of construction projects throughout the world. The design method, execution procedure and quality control and assurance of pile foundations are standardized in many countries based on the accumulate research results, laboratory and field experiences. In Japan, steel pipe piles are mainly constructed by hammer driven in port construction. On the other hand, precast pre-stressed concrete piles or cast-in-place piles are mainly used in on land construction. When precast pre-stressed concrete piles are constructed, piles are usually set by inner excavation method because of preventing noise and vibration problems. More than 50 years ago, noise and vibration problems had not been serious problem in Japan, but around 50 years ago, they became serious and now less noise and vibration construction methods are used for pile construction on land in Japan. In Asian countries, though piles used for construction have a lot of variety, precast pre-stressed piles are commonly used. In this report, execution controls of construction methods of steel pipe piles and precast concrete piles are mainly considered."

Jan 1, 2014

By Maurizio Siepi

The realisation of most of the civil engineering works is subordinate to the execution of consolidation works, in order to improve the soil physical-mechanics characteristics. The works classifiable with the term "Soil Improvement" can be realised using several technologies, among which the Deep Mixing Method is distinguished for his remarkable flexibility and productivity characteristics. The Deep Mixing Method is a process whereby a rotary drilling machine mechanically drills a constant diameter hole while cement slurry is injected into the soil at high pressure. The process combines state of the art construction techniques merging mechanical and hydraulic mixing energies at the tool bit. The result is a soil-cement column of engineered strength, consistency and dimension. Whereby the soil cement column formation process is controlled by a computerised device, the result is a speedy installation, thorough mixing, and a high degree of control, repeatability and documentation.

Jan 1, 2002

By Michael J. Atwood

Many buildings in Boston are founded on untreated wood piles, which can deteriorate and lose their structural capacity if groundwater levels are lowered below the tops of the piles, exposing the wood to air in the unsaturated soils that surround the piles. The problem of wood pile deterioration due to lowered groundwater levels in Boston first became evident in 1929 following discovery of rotten piles beneath walls of the Boston Public Library building. Repairs to reconstruct the library building?s wood pile foundations were made in 1930 using pit underpinning methods. Today, more than 80 years later, the subsurface conditions beneath several of Boston?s historic neighborhood areas continue to be plagued with low groundwater levels - regrettably resulting in ongoing deterioration to the wood piles that support some of Boston?s oldest and most beautiful buildings. Pit underpinning is still recognized as the preferred approach to repair wood piles and restore uniform foundation support beneath the impacted buildings. This paper provides a brief historical review of the land filling in Boston through the early 1900s that led to the use of wood piles as building foundations. Also discussed is the impact that groundwater level can have on the long term performance of wood pile foundations and the pit underpinning procedures used to reconstruct decayed wood pile foundations in 1930 beneath the Boston Public Library, and today beneath some of Boston?s oldest buildings. Also included are discussions on engineering controls and permitting requirements that help ensure safety and protection to the workers and buildings during underpinning, and some procedures being used to supplement and improve the loading capacity of the reconstructed foundations and facilitate construction of new useable below-grade space.

Jan 1, 2011

By Gao Dazhao

This paper presents some research results of pile foundation performance. Measurements on the bearing behaviour and driving effects of piles have been carried out during pile testing and pile driving. It has been found that the ratio of end resistance to the ultimate load depends on the pile length, and the ratio in general is less than 40% for single piles. However for pile group, the end resistance seems to be greater than skin friction. The characteristic curves of skin friction and end re­sistance appear as interaction between soils and pile. The contribution of skin friction to the pile bearing capacity not only depends on soil properties but also on the relative position of the soil layer. The pore pressure and the lateral pressure in ground have been observed during the stage of driving piles. Based on the available data, the radius of plastic region and the coefficient of pore pressure A can be found analytically. The pore pressure time process curves which may be used for practice have been predicted by means of numerical method.

Jan 1, 1991

By Jesús E. Gómez

In the Summer of 2011, emergency repairs to the Jefferson Memorial North Plaza and Seawall were completed. These repairs were necessitated by settlement and lateral movement of the seawall and North Plaza which prompted the National Park Service (NPS) to initiate an investigation as to the possible causes of the movement, and commission a design for its mitigation. Information gathered from extensive instrumentation on site led to the design of a movement mitigation scheme that included demolition of the Ashlar Seawall and reconstruction of a new seawall. The new seawall foundation is an A-Wall consisting of vertical caissons and battered pipe piles connected to the seawall itself. The scheme provides resistance to future vertical and lateral movement of the North Plaza and the new seawall. Repair to the seawall and plaza began in December 2009, and was completed in August 2011. This paper discusses the mechanisms believed to be responsible for settlement and lateral movement, summarizes the procedure followed for design of the mitigation, and describes the construction methods and some challenges faced during the repair.

Jan 1, 2011

By Kanchan K. Sen

The North Shore Connector (NSC) project will extend the Allegheny County Port Authority?s Light Rail Transit System from downtown Pittsburgh below the Allegheny River to the North Shore via twin bore tunnels. Jet grouting, diaphragm walls, and soil mixing were selected as cost-effective technically viable ground improvement and support of excavation techniques. Jet grouting was specified to provide break-out (egress) and break-in (ingress) block sections at the tunnel boring machine (TBM) launching and receiving pits. Jet grout treatment was also used adjacent to buildings with shallow foundations and below retaining walls along the tunnel alignment. A new method for measuring jet grout column diameter based on electrical resistivity was employed on the project. New equipment was introduced in the U.S for constructing soil mix temporary support of excavation using a soil-mix technique termed Cutter Soil Mixing (CSM) due to the use of two vertical cutting wheels that have evolved from diaphragm wall trench cutter technology. The system allows for continuous water tight soil mix panel construction including steel beams. This paper highlights some applications of jet grouting and various support of excavation systems (e.g. slurry walls, cement bentonite walls and CSM walls), including new innovative techniques (e.g. Cyljet and CSM) used under the constraints of an urban environment.

Jan 1, 2010

By Rudolph P. Frizzi

"Abstract Pile design for building structures in the United States is typically performed by: 1) investigating and assigning engineering parameters to the respective ground bearing materials, 2) calculating ultimate pile to ground (geotechnical) capacity which is then reduced by a Safety Factor deemed appropriate by a registered Design Professional thereby arriving at an allowable pile geotechnical pile capacity, and 3) determining the required pile structural section using allowable pile section material properties. It is advantageous to use a Working Stress Design Method (WSDM) approach as one system of loads (service loads) are used in both the geotechnical and structural evaluation. There are a variety of methods used to determine the ultimate and allowable geotechnical capacity, and Building Codes often require a registered Design Professional to determine the appropriate method(s) and capacities. The International Building Code is the Code typically referenced in building design and construction in the United States. Structural design usually follows Building Code requirements and Allowable Stress Design (ASD) procedures. As design of the overlying structure typically follows a Strength Design Method (SDM) approach using factored loads, in some cases piling is first designed for pile-to-soil interaction using service loads, followed by evaluating the pile geometry for factored loads. Construction is the finalization and implementation of the designed piling. As such, project-specific technical specifications are typically developed by a registered Design Professional such that a project Owner can bid, buy, and instruct a Contractor as to the desired piling work and acceptance criteria. There are several Industry groups, including DFI, PDCA, ADSC, and ACI that provide guidance documents which the registered Design Professional can refer to in developing the piling technical specifications. It is the author’s opinion that the registered Design Professional is best suited to observe and verify the piling installation; many Building Departments require verification and documentation by a registered Professional as a condition of final acceptance.INTRODUCTIONPile design for building structures consists of: investigation, design, specification, and verification. In major metropolitan areas within the United States, Building Codes typically identify minimum requirements for each of the above steps. The International Building Code (ICC, 2012) is the Code typically referenced in building design and construction in the United States. Recognizing the ground conditions as well as piling construction means and methods can vary on a site-by-site basis, latitude is given to the registered Design Professional and Contractor to optimize the piling system for the respective project conditions. Field testing and quality control / assurance measures are typically implemented to verify the design intent is attained for the production pile elements."

Jan 1, 2014

By Andreas Brandner

"At the beginning of 2007 the Austrian contractor PORR was awarded with remediation works for a 48-km long part of the railway line from Campina to Predeal – part of the Trans European main Corridors TEN-T priority line 22 Bucurest – Brasov, connecting the southeast European countries with the heart of Europe.Due to partly new realignment and change of regular sections as well as protection against rockfall and slope slide a huge bunch of slope stabilization works became necessary, which were awarded to the contractor PORR and their designer IB-Brandner.Following the studies of the tender documents for the planned protection measures responsible managers of PORR decided to propose an alternative protection design by IB- Brandner. Changing the original design a more flexible and environmentally compatible solution consisting of high performance net, soil nailing and rockfall protection systems (fences) was elaborated and adapted to local needs. During design process, several critical areas were identified and additionally taken into account.In the paper examples of the design and erection process show how difficulties in implementation starting with the presentation of the idea continuing to the realization on site were managed and a technically more sophisticated and commercially competitive solution could be delivered to the customer Romanian Railway – case study.The European Commission awarded – following an election process in which all citizens of the EU could join - the remediation project Railway line Campina – Predeal in Romania as the environmentally best EU co-financed infrastructure project. GENERAL PROJECT EVALUATIONDue to original design slope stabilization should be done by concrete slabs fixed with prestressed anchors and shotcrete cover.The area to be secured was limited to a 12-meter strip left and right from the railway track without reference to nature and local needs. Discussions with the client and his designer and rising awareness for the hazards to address took several months. Site visits in Austria to provide insight in the problems of dealing with natural hazards helped to convince the client of the needs and our alternative design."

Jan 1, 2017

By Balu E. George, Subhadeep Banerjee, Shailesh R. Gandhi

"A three-dimensional analysis of laterally loaded helical piles installed in cohesionless soil is presented. Finite Element Analysis was conducted using commercially available Plaxis 3D AE version, assuming Mohr-Coulomb failure for soil. Pile is modelled as plate elements with a single helical blade attached to a hollow shaft. The ultimate load for various configurations is examined considering deformation criteria. The Bending Moment distribution and maximum lateral deflection are also discussed. It was observed that the ultimate lateral load carrying capacity increased by presence of helical blade and the maximum deflection also got reduced. The diameter of the helical blade was found to have significant effect on the lateral deflection, maximum bending moment and the ultimate load. However, the observations from the study suggest that the presence of helical blade seizes to produce considerable effect after a certain depth. Difference in failure pattern with regard to the distribution of soil resistance observed for different geometries considered for numerical analysis are also touched upon.INTRODUCTIONHelical piles or screw anchor piles have gained popularity due to fast installation, instant use, and other advantages over the traditional piles. They are usually used to support structures like solar panels, light houses, and other light structures which are subjected to uplift loads. However, such structures are often subjected to significant lateral loads as well. Under lateral loads, the response of helical piles can be different from that of a conventional pile due to the presence of the bearing provided by the helical blade. However, the proper design remains a concern due to lack of work carried out on the lateral capacity of helical piles.The lateral performance of helical piles is significant because they can act as efficient alternative to conventional piling systems in many applications.The lateral load capacity of screw anchor piles with different number of helices were examined by Mittal et al. (2010) by experiments in sand. They found that the lateral load capacity of piles increases with addition of helical blades. Prasad and Rao (1996) examined the lateral capacity of helical piles in clay by experiments on model piles and found that the lateral capacity of helical piles were more than that of the straight shaft piles. It was observed that the lateral capacity increase with embedment depth and shear strength of soil. Sakr (2009) studied lateral performance of two section helical piles in soft soil. The investigation by Prasad and Chari (1999) reported that the pressure distribution across the diameter is not uniform for circular piles, but it is maximum at the centre and almost zero at the two edges.Puri et al. (1984) after conducting model tests on single-helix, two-helix, and three-helix anchors installed in sand, proposed a mathematical model that was fashioned after Matlock and Reese’s elastic theory model. Elkasabgy and Naggar (2015) investigated he lateral performance of full scale large capacity helical piles in structured cohesive soils and reported the modulus of sub-grade reaction to be non linear."

Jan 1, 2017

By Robert Jakiel

The following paper is being presented to provide a basic understanding of the equipment and procedures used in multi-auger deep soil mixing as part of the program for the Deep Foundations Institute (DFI) Deep Soil Mix Seminar. The paper is written as a summary of the author&apos;s experience using multi-auger deep soil mixing equipment while working with SMW Seiko, Inc. on several east coast projects in the United States, particularly the soil-cement mixing for the soil stabilization of the Fort Point Channel area in Boston, Massachusetts, one of the largest and most difficult soil mixing projects completed thus far in the United States. The summary provides a brief summary and insight into some of the operational aspects of the equipment and procedures, and some of the important considerations when using multi-auger deep soil mixing. This paper is intended for use by both the contractor and the designer involved in selecting appropriate soil mixing equipment and procedures for various types of soils, depths or applications, or for a better understanding of the operational aspects, potential benefits, and impacts that the performance criteria may have on the operational capabilities of the soil mix equipment, when specifying multi-auger soil mixing for a particular project. Prior to reading this article it is important to become more familiar with the various acronyms and terminology used in soil mixing technology. A Definitions section has been provided at the end of the paper that will help the reader become more familiar with some of the terms used throughout this paper.

Jan 1, 2001

By K. Viking

The vibratory characteristics of full-scale sheet piles, vibratory driven into the ground, have so far not been described systematically in detail. This paper concerns the preliminary results of a series of full-scale field tests where both the driveability and induced ground vibrations have been continuously monitored. Furthermore, the results of measured ground vibration levels have been measured at two different sites characterised as having hard and easy driving conditions. In the light of the presented results, the paper briefly discusses how the complexity of a driveability and vibration prediction can be subdivided into three parts, namely, vibrator-, sheet pile-, and soil-related parameters, all of which significantly affect both the driveability and induced ground vibrations.

Jan 1, 2000

By Peter Faust

The foundations for the new South Viaduct Bridge in San Francisco were extremely challenging due to the requirement for very large and deep piles installed adjacent to historic structures. Drilled shafts up to 12? foot in diameter were constructed to a maximum depth of 200? feet in alluvial soils and Franciscan Bedrock using an oscillator system for the installation of the permanent steel casing. This paper provides an overview of the construction techniques, the equipment, and the challenges associated with constructing 12? foot diameter shafts on this very complex project in one of the nation?s nicest landscape setting.

Jan 1, 2011

By Yvone Franco Crosato

The dense population of Hong Kong requires the construction of tall buildings in reclaimed areas or perched on the slopes of the many hills. The large loads to be supported are carried by deep foundations. Many of those are bored piles, to rock, of diameters up to the 3.0 m. of today.

Jan 1, 2000