Search Documents

By V. Tang

In this paper, Chinese economic situation are estimated and prospective developments predicted to assist those US firms who have been trying to do business in China, or are considering to pursue the China market.

Jan 1, 2010

By Benjamin B. Buensuceso III

Crosshole sonic logging (CSL) is a popular quality assurance and quality control method used to examine the concrete quality of cast-in place deep foundations, though the evaluation of the results is subject to certain limitations. One such limitation explored in this paper is the occurrence of false positives, where signal anomalies indicated by CSL test results are not necessarily indicative of imperfections in the foundation that could affect its performance. A case study of false positives evaluated in CSL records in a major infrastructure project in Metro Manila is presented in this paper. A detailed desktop evaluation and results from complementary high-strain dynamic load testing and low-strain pile integrity testing were used to evaluate the significance of the suspected false positive signal anomalies from the CSL test results. Recommendations for the proper interpretation and evaluation of CSL test results in Philippine practice, given the method’s limitations and examples presented, are also shared.

Sep 8, 2021

By George Piscsalko

Quality control of drilled shafts and ACIP piles is greatly dependent upon the practices of the site personnel. In many applications it is difficult to properly inspect the shaft prior to concreting, such as when the shaft is drilled under slurry. In other cases, such as ACIP piles, it is impossible to inspect the shaft in any manner prior to concreting. There are numerous methods currently available to assess the integrity of drilled shafts and ACIP piles. Each method has its advantages and limitations. This paper will compare the various available methods as well as introduce a new method for assessing integrity in drilled shafts and ACIP piles. This new method, known as Thermal Integrity Profiling, determines the integrity over 100% of the shaft both inside and outside the reinforcing cage by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements can be made by either passing a thermal probe through a standard Cross Hole access tube typically 12 to 48 hours after concrete placement, or from embedding thermal wires within the shaft prior to concrete placement and monitoring them with unattended data collectors for 12 to 48 hours after concrete placement. This Thermal Integrity Profile method will be described in detail and several case histories will be presented. Additional testing methods which will be compared include low strain Pile Integrity Testing, and Cross Hole Sonic Logging. Advantages and limitations for each method will be discussed.

By Adrian Mercer, Ashkan Ameri

Due to general degradation, increased traffic levels, and historical ground movement, this road and rail bridge which provides an essential link between the interior of the country and the Port of Abidjan, required significant repair and reinforcement. This included strengthening the pre-stressed concrete box girders and replacement of the existing bored pile foundations. Replacement piles had to be adjacent to, and no longer than, the existing piles, in order to not compromise the stability of the operational bridge during the works. The underlying geology, however, meant that the pile loads had to be predominantly transferred into the ground through end bearing. Rather than installing a greater number of piles or larger diameter piles, innovative thinking changed the usual mind-set of designing the piles to the prevailing ground conditions, to designing the ground conditions to suit the piles. Jet grouted columns were installed beneath the toes of the new piles to increase the bearing capacity of the ground. This significantly contributed to the sustainability of the project and reduced carbon emissions through saving concrete, steel, plus transportation and disposal of spoil.

Sep 8, 2021

By Nicholas P. Gura

This paper presents the analysis, design, and load test program results for drilled shafts to support a 70-story hotel tower and associated 10 story podium structures located in Las Vegas, Nevada. A mat foundation for the structure, although feasible, would have produced undesirable differential settlements within the high rise tower footprint and at the interface with adjacent lower level podium structures. The resulting foundation system solution for the 70-story, approximately 800-foot long hotel tower was four-foot diameter drilled shafts, extending 100 below shaft cutoff. The design compression capacity for the four foot diameter drilled shaft was 5,000 kips. The load test program proved that the unique Las Vegas valley geology lends itself to efficient installation, precluding the need for engineered slurry or casing. The load testing program included the installation of two four-foot diameter test shafts to 100 feet below theoretical cutoff and the performance of two highly instrumented independent Osterberg load cell tests with maximum sustained test loads of 12,000 kips. Sonic caliper testing was also performed to document actual in-place shaft diameters and verticality. The load test program also provided information necessary for the foundation design of the podium structures. In addition to the tower?s drilled shaft load test program data, continuous flight auger (CFA) pile evaluation and testing was also performed. The CFA testing consisted of traditional ?top down? loading techniques and was performed as an alternative to the recommended shallow drilled shafts for the lower level podium structures. The results of the CFA test program provided supplemental, insightful soil friction data which was used in conjunction with the drilled shaft test program data in evaluating the most appropriate support for the lower level structures.

Jan 1, 2007

By Peter J. Nicholson

Recognition of the liquefaction susceptibility of dam embankments has been heightened since the San Fernando Dam near failure incident in 1971. Both the downstream and upstream slopes of dams can be at risk for slope failure that can lead to breaching of the dam during or after a seismic event. Many dams have been remediated by various means such as the installation of stone columns or by excavation and replacement of the liquefaction susceptible material. Recent engineering and technology advances in equipment and materials has shown that construction of shear walls to the appropriate depths and at the right center to center spacing may be an economical alternative to the more traditional methods. Recently, the downstream embankments of at least 4 dams, from South Carolina to California, have been, or in the process of being remediated by the use of shear walls. The method of installation has been either multi-axis Cement Deep Soil Mixing walls or walls constructed by the use of trench excavation under self-hardening slurry. Four case histories of dam remediation are discussed, three by multi-axis paddle auger CDSM equipment one with the use of self hardening slurry trenches.

Jan 1, 2008

By Donald Deardorff

Helical piles often rely on the final installation torque for ultimate capacity verification. When helical piles are designed using traditional bearing capacity equations for deep foundations and field monitored for a specified final installation torque, a factor of safety equal to 2 is often allowed for the design. One of the more common methods of determining torque during helical pile installation is by correlating the differential pressure across a hydraulic gear motor to a torque. Most drive head manufacturers provide multipliers to convert differential pressure to torque for different drive head models. These multipliers are based on theoretical torque equations and vary with the planetary gear ratio, hydraulic gear motor displacement and drive head efficiency. Drive head manufacturers show a linear fit between the differential pressure and output torque with no scaling effect. Previous drive head testing performed by the author has confirmed that the drive head differential pressure to torque relationship is generally linear however there is a scaling adjustment needed. This results in a variation of multipliers across the differential pressure range for a given drive head. Eight hydraulic drive heads from three manufacturers were field tested by Foundation Supportworks, Inc. to compare the torque versus differential pressure curves with varying installation equipment, hydraulic line sizes and hydraulic flow rates. Differential pressure was monitored using three methods including pressure gages, PT-Tracker and an Ashcroft AT-100. Flow and temperature was measured using a Webtech system analyzer. Torque was measured using a Pro-Dig in-line torque transducer, a TruTorque indicator and a Chance Mechanical Dial in-line torque indicator. The current testing indicates that a change in installation equipment and/or a change in hydraulic flow rate may affect the torque versus differential pressure curve of a given drive head. The results of this testing also show that some of the methods for determining torque during helical pile installations may be unconservative, thereby resulting in safety factors less than required.

By James P. Hambleton, Anastasia Nally

This work focuses on the numerical simulation of multi-plate anchor systems (e.g., helical anchors) in sand subjected to vertical loading. In assessing the stiffness and capacity of these multi-plate anchor systems, full awareness of the abilities and limitations of the various analysis methods must be understood. This work first summarizes studies completed by others and then goes on to assess the failure mechanisms of multi-plate anchors in sand and the influence of (1) plate width-to-depth ratio, (2) number of plates, and (3) relative positioning of plates. The analysis makes use of (1) conventional limit analysis, (2) so-called modified limit analysis that employs reduced strength parameters to account for the influence of soil dilatancy, and (3) the displacement-based finite element method, which considers elastic as well as plastic deformation leading to failure. The work critically reflects on limitations in the current analysis methods for helical ground anchors. INTRODUCTION Helical anchors are a relatively low cost foundation type, typically consisting of a steel rod and single or multiple plate attachments. In recent decades, they have seen rapid growth, and as outlined by Merifield and Sloan (2006) and Hambleton et al. (2014). Design techniques for helical anchors have previously been predominately empirical, as much of the past research in this field is experimentally based. It is common practice for helical anchors to be modeled as horizontally oriented plate anchors in both numerical and experimental analysis. This work focuses on analysis based on the finite element method, including so-called finite element limit analysis and the conventional displacement-based finite element method, with some comparisons made to experimental studies. Numerical simulation of anchor pull-out capacity in cohesionless soils is stunted by the many difficulties faced when using numerical analysis with cohesionless soils. Additional variations can be seen when comparing the serviceability based load capacities to the ultimate load. In this work, both the force-displacement response (stiffness) and the ultimate anchor capacity are assessed, with more focus on the latter. This work focuses only on analysis techniques for multi-plate anchors with vertical loading in cohesionless soils. Many studies have been completed in this area, some of which assume a rectangular plate in a plain strain model (Rowe & Davis, 1982; Merifield & Sloan, 2006; Cerfontaine et al., 2019). Whereas others use axisymmetric conditions (Baker and Kondner, 1966; Saeedy, 1987; Murray & Geddes, 1987; Ghaly & Hanna, 1994; Sakai & Tanaka, 1998; Merifield et al., 2006;) and minimal studies considered both axisymmetric and plane strain in the one study (Vesic, 1971; Tagaya et al., 1988; Murray & Geddes, 1987; Sarac, 1989).

Jan 1, 2019

By Chris M. Haberfield

The design of side resistance of drilled shafts socketed into rock has traditionally been empirically based on the results of pile loading tests in which the side resistance can be isolated from the side resistance. In practice, this is achieved in one of several ways : loading the pile in tension, using a collapsible base, or by using a device such as an Osterberg cell to load the pile from the base. Although this approach has resulted in generally safe design practice, this has been at the expense of efficient design practice. Safety in design has been achieved through conservatism, which has been necessary because of the large scatter that is evident in the pile socket resistance database (Rowe and Armitage, 1984; Kulhawy and Phoon, 1993). Research at Monash University through the 1980's has been aimed towards understanding and then modelling the complex mechanisms of shear transfer at the concrete-socket interface of sedimentary rocks. Armed with such an understanding, the important factors which affect the strength of pile sockets can be isolated, and the reasons for the large scatter can be deduced. This paper briefly describes the research approach taken, and the main features of the design method and computer program which have now been developed. Some load-settlement predictions of the program are compared with the results of full-scale pile socket tests. The paper then presents the results of a numerical study which relates predicted socket a factors to unconfined compressive strength of the rock, socket diameter, initial normal stress and socket roughness.

Jan 1, 1996

By W. Morgan NeSmith

"The DFI ACIP Pile Committee, in conjunction with the Florida DOT, completed an ACIP Pile installation monitoring and performance test program in late 2016 to advance the inclusion of ACIP piles in future specifications for bridges by state agencies. Piles of different diameters were installed for compression, tension and lateral testing, and one pile was extracted for visual inspection. This paper presents the pile installation, non-destructive testing and load test results of the program.INTRODUCTION The Deep Foundations Institute (DFI) Augered Cast-In-Place (ACIP) Pile Committee performed a ACIP pile installation and test program in the fall of 2016 to demonstrate a fully monitored installation of 18-in and 24-in diameter ACIP piles. The program included automated and manual installation monitoring, Thermal Integrity Profiling, compression, tension and lateral load testing (including monitoring of strain gages embedded along the compression pile shaft), and post-testing extraction of an installed pile for visual inspection.PROJECT DETAILS AND FIELD EXPLORATION A general program location map along with an aerial view of the property in Okahumpka FL is shown in Figure 1. Two Cone Penetration Tests (CPT) were performed at initial reaction pile locations R-6 and R-8 (Figures 2 and 3) The results from CPT R-6 indicated very loose soil conditions at depths below 55-ft, indicating potential relic sinkhole conditions. The test layout was subsequently rotated and moved south of CPT R-8.TEST PILE INSTALLATION DETAILS Seven piles were installed to either 40-ft or 60-ft below grade. Thermal Integrity Profile (TIP) wires were installed in all piles but varied to include one wire each attached to a steel center bar or one wire attached to the steel center bar AND four additional wires (each) attached the steel reinforcing cage installed in these piles. Additionally, the 24-in lateral and compression piles had four steel or PVC casings installed next to the TIP wires for testing by thermal probe and/or wire inserted into the casing."

Jan 1, 2017

"1.0 DESCRIPTIONThis work consists of furnishing all necessary labor, equipment, and materials to install prefabricated vertical (wick) drains in the ground in accordance with the Plans and as specified herein.2.0 REFERENCED CODES AND STANDARDSASTM D4716-08 Standard Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant HeadASTM D4632-08 Standard Test Method for Grab Breaking Load and Elongation of GeotextilesASTM D4533-11 Standard Test Method for Trapezoid Tearing Strength of GeotextilesASTM D4491-99a Standard Test Methods for Water Permeability of Geotextiles by Permittivity (2009)ASTM D4751-04 Standard Test Method for Determining Apparent Opening Size (A.O.S.) of a GeotextileASTM 6918-09 Standard Test Method for Testing Vertical Strip Drains in the Crimped Condition3.0 QUALIFICATIONSThe Contractor shall have successfully completed a minimum of five wick drain installation projects in similar ground conditions, and installed not less than 5,000,000 linear feet (1,525,000 linear m) of wick drain in the past five years. The Contractor shall have a minimum of five continuous years of wick drain installation experience."

Jan 1, 2014

By Harald P. Ludwig, Matthew J. Niermann

The support of excavation (SOE) for the Capitol Crossing project in Washington, DC consisted of a combination of soldier piles, lagging, tiebacks, braces, underpinning, single auger soil mixed (SASM) walls, micropiles, and a tiedback slurry wall. Over 130,000 square feet of SOE was installed with more than 1,300 tiebacks providing lateral support for excavation depths of up to 72 feet. Several structures including the Holy Rosary Church, the Bell Tower, the Casa Italiana, and a modern office building were supported by a combination of conventional hand dug underpinning pits, bracket piles, and stiff SASM walls. This paper will focus on the design and performance of the SOE adjacent to the Holy Rosary Church and the Bell Tower. Deflection-based design was used to estimate the movements of and limit damage to these structures. An extensive monitoring program was used to provide real time movement data. The results of

By Charles M. Wilk

"Mass stabilization (MS) is a ground improvement technique that can prepare areas of low bearing strength soil for subsequent infrastructure development. The technique involves mixing binding agents such as portland cement, fly ash, slag, or lime into the subject soil while the soil remains in-place (insitu). The binders “cement” the soil grains together to form a cement modified soil or a soil cement. The MS-treated area now has improved bearing capacity to support infrastructure or to prevent movement of the material such as landslides.The same insitu soil mixing technique can be used to address contaminated areas. Binders or reagents are mixed into soil. The treatment protects human health and the environment by immobilizing hazardous constituents within the treated material. When used for the purpose of environmental remediation the technology is called Insitu Solidification/Stabilization (ISS).Both Mass Stabilization and ISS treatments require laboratory studies to develop a mix design of soil and binder(s) that produce the desired physical and/or chemical properties. The mix design is then transferred into the field. Successful MS and ISS treatments rely on reproduction at full-scale of the mix design and the thorough mixing attained at laboratory scale. Fifty to 70% of the cost of a MS or ISS project is in the cost of the binding agent that is to be mixed into the subject soil. Under-dosing, overdosing, non-thorough mixing, and mixing in the wrong areas all create cost over-runs.This paper will discuss recent innovations in mass stabilization systems that improve the cost effectiveness of the treatment technology. Specialized equipment can impart greater mixing shear thus improving the thoroughness of mixing. Dry powder pressure feeders can conserve the “drying capacity” of binder resulting in higher strengths at lower binder dosages. Global Positioning System (GPS)-based systems can guide the mixing operator for complete mixing coverage. An integrated tracking and feeding system can record that proper dosing and mixing was accomplished and generate construction QA/QC reports for the client.INTRODUCTIONNew or expanding infrastructure projects may encounter areas of low bearing capacity soil or areas where marginal materials such as waste, dredged material, or sediment have been placed. Mass stabilization is a geotechnical method that can be used to improve the bearing capacity or stiffness of soil. Mass stabilization involves mixing binding agents into soil subject to treatment while the soil remains in-place or insitu.Mass stabilization technique can also address contaminated soil therefore, the same technique can be used to attain both civil and environmental engineering goals. In this environmental application the technology is known as insitu solidification/stabilization (ISS). ISS protects human health and the environment by immobilizing hazardous constituents within the treated material."

Jan 1, 2015

By Brian McGlynn

There are many factors that can result in a site characterization being limited. For example, a client may undervalue the importance of a good geotechnical report, or an owner may feel that it would take too much time to perform an appropriate investigation among other reasons. For this project, neither was the case. The challenge was that the construction sequence of work required wick drains to accelerate the settlement of soil that had yet to be placed, resulting in the need to create a wick drain bid package based on unknown settlement parameters. This wick drain project took place in Long Beach, California, at the Long Beach Middle Harbor Re- development. For much of the past decade, the Port of Long Beach undertook a $1.5 billion redevelopment of two outdated terminals to create the Long Beach Container Terminal (LBCT). To achieve this goal, the existing terminals were demolished and the slip that serviced one of the older terminals was designed to be infilled to create the new area that would allow for the LBCT to manage 3.3 million TEUS (a commonly used freight term meaning twenty-foot equivalent unit) of cargo each year. Ultimately, the construction of the LBCT would be performed under multiple contracts to allow the new terminal to begin operation in a phased approach. Menard performed the wick drain installation under two out of three contracts, and this case history focuses on the challenges anticipated and faced under the second of these awarded contracts.

May 1, 2023

By James P. Hambleton, Sam A. Stanier

A perceived advantage of screw-type foundations is the ability infer aspects of foundation performance from quantities measured or observed during installation, especially the installation torque. A particular concept widely used in practice is to correlate installation torque to ultimate capacity. This notion has proven useful as a field verification technique despite the absence of validated models that relate key variables of interest, such as installation torque, axial (crowd) force, geometrical parameters, and soil strength. This paper considers previous work by the co-authors and collaborators on analytical, numerical, and physical modelling of screw piles to relate the quantities measured or controlled during installation (e.g., installation torque) to the ultimate capacity and soil strength. Attention is given to saturated clay as a particular soil type amenable to simplified analysis. An analytical model for a single-helix pile is considered as a means of directly relating the ultimate capacity and undrained shear strength to the installation torque, crowd force, plate pitch, plate diameter, shaft diameter, installation depth, and surface roughness. The connection between the installation variables and ultimate capacity—and the sensitivity to crowd force in particular, a quantity that is typically not measured during field installations—is also discussed. The theoretical predictions are compared against data obtained from small-scale laboratory experiments that suggest the installation torque relates to the remolded strength of the soil. INTRODUCTION Screw piles are deep foundations that are twisted into the ground through an applied torque. Advantages over driven piles or drilled foundations include the relative silence of the installation, with low ground vibrations, and the possibility of being easily decommissioned by reversing the direction of twisting. Screw piles are now routinely encountered as a flexible, low-cost solution for numerous applications (Figs. 1 and 2), and they are also being considered for applications in offshore energy production due to limitations being imposed with respect to decommissioning and underwater noise. Also known as “screw anchors,” “helical piles”, or “helical anchors,” screw piles consist of helices or helical plate elements attached to a central shaft. Figure 3a shows the components of a single-helix pile and key variables. The diameters of the shaft and helix are denoted by d and D, respectively, and p is the pitch of the helix. Variable H denotes depth of the helical plate, and T and N denote the torque and axial (crowd) force applied during installation. In typical applications, the pile includes multiple helical plates, and the shaft is composed of segments that allow for it to extend to large depths into the soil.

Jan 1, 2019

By David R. Black

Foundation problems due to collapsible and expansive soils are well known throughout the arid western United States. Millions of dollars are spent annually to counteract the effects of such soils for both new foundations and existing foundations suffering from settlement or heave. Over the last 20 years helical screw piles have come into wide-spread use as a permanent deep foundation element for these problem soils, especially in the arid western United States where, in some areas, they are a standard of practice. Independent research resulting in recognition by every national building code in the United States has legitimized helical screw pile technology. Once thought of in terms of light structural underpinning, helical screw piles of today are designed to take heavy structural loads, vertical and lateral, tension or compression, including seismic loads. With proper pile grouping, design capacities for column loads over 4,500 kN (1,000 kips) are attainable. This paper discusses design considerations specifically dealing with collapsible and expansive soils: soil investigation parameters, predicted settlement and long-term creep, heave in expansive soils, downdrag in collapsible soils, shaft slenderness buckling, maintaining shaft alignment during installation, refusal condition, water migration along the shaft, lateral loading, cyclical loading for seismic loads and machine foundations, corrosion, helix durability during installation, the installation torque vs. capacity equation, and design methodology. The paper concludes with several case histories where helical screw piles were used for new structural foundations and to underpin existing failed foundations in St. George, Utah, Cedar City, Utah, and Denver, Colorado, USA, sites of some of the most expansive clay and collapsible soil in North America. Soil descriptions and performance histories are presented.

Jan 1, 2002

By Joseph T. Coe, Siavash Mahvelati, Philip Asabere

Characterization of existing foundations remains an important issue as foundation reuse and rehabilitation continue to garner increased attention. In the case of unknown foundations, geophysical and nondestructive testing (NDT) methods have been utilized in the past to evaluate foundation geometry and could serve as useful tools in the case of foundation reuse. A comprehensive study was initiated in the late 1990’s and early 2000’s that evaluated the effectiveness of the available geophysical and NDT technologies to characterize unknown foundations for scour evaluation purposes. At the time of that study, the Multichannel Analysis of Surface Waves (MASW) geophysical method was in its infancy and not widely used. Since then, MASW has become increasingly prevalent in geotechnical applications as the method presents a number of potential advantages when characterizing the subsurface, including rapid testing, increased signal to noise ratio, and ability to resolve velocity inversions. This paper presents a case study that explores the abilities of MASW as an unknown foundation characterization tool. MASW was applied to determine subsurface stiffness at a bridge foundation site in the Philadelphia metropolitan area. One MASW survey line was performed immediately over the foundation of interest and another was performed over a control zone adjacent to the foundation to establish a baseline site profile. The purpose of this testing was to examine whether MASW could establish the geometry of the foundation at this site. This paper presents the site conditions and MASW testing procedures, followed by a discussion of data analysis and interpretation.

Jan 1, 2016

By Vishal Pathak, Shailesh A. Godhuly

Ground Modification System in terms of Jet Grouting for soil strengthening and mass stabilization was engaged for a power plant project in an international power project, engineered by L&T-S&L. The site Geology consist of cohesionless type of sandy alluvial deposits (silty fine sand) as the main formation. Ground water table is encountered at shallow depth. Geological interpretation is done using soil investigation data along with CPT’s. This paper discusses design and implementation of jet grout technique to improve the mechanical behaviour of soil. To distribute load evenly from superstructure, a layer of growmast (drainage blanket) is laid above jet grout columns. Settlement evaluation is done using Finite element analysis with Plaxis 2D and Settle 3D. In the project, selected equipment foundations are resting on jet-grout columns including vibratory equipment like 144MW Gas Turbine etc. The project has been commissioned in September 2021 and operating with full capacity.

Sep 1, 2022

By Paul Summers, Kevin Richardson, Willem (Billy) Villet, Paul J. Sabatini, Attasit Korchaiyapruk, Edward C. Clukey

"A deep mixing method (DMM) foundation was selected by the Project Team for a very large LNG facility in West Africa. As described in a companion paper, this foundation consists of a large number of columns installed by mixing cement with in-situ soils. The foundations are arrayed as a variety of honeycombed type configurations which, if installed to desired specifications, can provide a robust foundation alternative. The foundation is capable of distributing loads and limiting settlements even if some of the soil in the columns is not fully mixed during installation. An important part of the overall quality assessment program, therefore, involved developing a testing program to verify the methodology. In addition the impact of potential defects in columns on the overall foundation integrity had to be assessed. This paper describes some of the preliminary work done to establish the requirements for the quality assurance program. A key component of this program involved the sampling frequency used to assess potential defects in the columns. To verify the column integrity 104- mm samples were taken continuously at a selected frequency through the 23 m long columns. The preliminary work described in this paper demonstrated that the appropriate sampling frequency depends on both the desired reliability level as well as the number of defective columns encountered during testing.Initial finite element analyses were performed to assess the extent that defects could occur in columns within the honeycombed structure without adversely affecting the overall foundation integrity. The results from this work demonstrated that the spatial location of the defects was critical to properly assessing the foundation integrity.In addition to column sampling a load test was performed as part of the foundation verification process. The methods used to apply appropriate loads so that loads at the bottom of the columns approached design values are discussed in the paper.The results obtained from this preliminary study were then used to help develop a more comprehensive assessment program, described in a companion paper, to determine the robustness of the DMM foundations for both the LNG processing facilities and a condensate tank.IntroductionFoundations constructed with the Deep Mixing Method (DMM) can be an attractive and cost efficient alternate to other deep foundation options. This foundation is constructed by mixing soil and cement with an auger type drill. The foundation is usually constructed with a dual auger system that simultaneously creates two contiguous columns called foundation elements. Many elements are then arranged in a honeycombed configuration to create the overall foundation (Figure 1). A desired column strength can be obtained by varying the volume of cement added to the columns, the mixing rate of the soil and stroking sequence."

Jan 1, 2017

By Dan Brown

Improvements in construction equipment and techniques in recent years have made possible the use of drilled shaft foundations in diameters and lengths not previously considered practical or feasible. Many highway bridge and other structures are now routinely founded on drilled shafts which are 2.5 m to 3.0 m (8 to 12 feet) in diameter and extending over 60 m (200 feet) in depth below grade. There are unique challenges associated with constructing such large and deep cast-in-place foundations and engineers should be aware of the special needs associated with site investigation, construction specifications, material requirements, and quality assurance. This paper outlines a number of special considerations for these foundations, along with strategies that may be employed to improve the reliability and quality of large drilled shaft foundations.

Jan 1, 2008