Search Documents

By Lastram Rolando, Larry J. Hulbert, Louis J. Cabri, J. H. Gille Laflamme, John L. Campbell, Soey H. Sib, Chris G. Ryan

"The mineralogy of samples from the Wellgreen Cu-Ni-Pt-Pd deposit, Yukon Territory, is complex and the metals of interest are contained within fine-grained minerals which vary in size and mineral associations from sample to sample.The major Ni carriers are pentlandite and violarite; the major Cu carrier is chalcopyrite. About 700/0 of the major Ni carriers and 78% of the major Cu qurier will be liberated at a grind of 80% -U,.7 ,an (-500 mesh) for typical low-grade gabbro (West zone, sample No.1). For typical ""clinopyroxenite"" (West zone, sample No.2) and typical ""clinopyroxene-rich peridotite"" (East zone, sample No.3) the liberation would be 71% and 65% for Ni, 74% and 60% for Cu, respectively. Fine grinding, however, cannot liberate the Ni contained in silicates and pyrrhotite, estimated to total 24.5% for typical low-grade gabbro (West zone, sample No. I), 15% for typical ""clinopyroxenite"" (West zone, sample No.2), and 12% for typical ""clinopyroxene-rich peridotite"" (East zone, sample No.3).The principal Pt carrier (sperrylite) varies considerably in grain-size between samples and fine grinding, required to liberate the major Ni and Cu carriers, may be counterproductive in samples where sperrylite is relatively coarse-grained, as some would then be unrecovered (e.g. sample No. 1). In addition, sperrylite in samples No.2 and No.3 is closely associated with magnetite. Palladium occurs in diverse ways. It occurs in the form of several Pd minerals (e.g. sudburyite, testibiopalladite, merenskyite), as a replacement for Ni in several tellurides, antimonides and tellurantimonides (e.g. melonite), or as very low concentrations in pentlandite (up to 34 ppm), chalcopyrite (up to 9 ppm), and pyrrhotite (up to 5.6 ppm). Palladium minerals and Pd-bearing minerals are strongly associated with chalcopyrite in sample No. 1 and will thus report to a Cu concentrate.However, 22% of the total Pd is in solid solution in pentlandite in this sample and will thus report to the Ni concentrate. In samples No.2 and No.3, less Pd occurs in solid solution in pentlandite, and the PGM are distributed mainly among pentlandite, chalcopyrite, and magnetite in sample No. 2, and among pentlandite, pyrrhotite, chalcopyrite, and magnetite in sample No.3. Therefore, the feasibility of magnetic concentration should be investigated for samples like No. 2 and No.3, in order to improve Pt and Pd recoveries. Rhodium was found to occur as rare hollingworthite, in sparse cobaltite (up to 2.7%) and, as low concentrations in chalcopyrite (to 10 ppm) and pentlandite (to 12 ppm) by proton microprobe. Iridium occurs in hollingworthite (up to 7.8%) and very rarely as the native metal or in an undefined Re-Ir-Qs..Ru alloy. Ruthenium was determined by proton microprobe analyses to occur in pentlandite (up to 13 ppm) and chalcopyrite (up to 10 ppm), in addition to rare laurite and Re alloy."

Jan 1, 1993

By V. Maazallahi, A. Rouleau, A. Saeidi

"The geometry of the terrain topography before and after the failure are the essential factors for analyzing a landslide and for the design of remedial works. This paper presents a method to determine these factors, considering that the determination of the slide surface profile is difficult and costly using traditional methods and the pre-slide topography data is often not available. The presented method to locate the 3-dimensional geometry of the slide surface is based upon determining the slide surface in 2- dimensional vertical sections. This method utilizes post-slide topography of the area to determine the pre-slide topography and uses equations to estimate the pre-slide situation using a statistical process applied to points located on the sliding mass. This method is tested on the Maskun landslide in Iran. The results indicate the applicability of the proposed method to obtain the key factors for the back analysis of a landslide in a cost effective manner.INTRODUCTIONProbably the most reliable method of determining the strength of soil and rock mass is to back analyze a failed or failing slope (Caia et al. 2007; Wyllie & Mah, 2004). This method is used in geotechnics for estimating geotechnical parameters of the rock and soil mass (Sakurai et al., 2003; Frayssines and Hantz, 2009; Cepuritis et al. 2010), but it requires that the failure mode is well established and that there is complete and precise information available on the slide surface and the sliding mass (Sjöberg, 1996). Measurement of the slope profile before failure provides the basic information required for a back analysis (Hock & Bray, 1981). The post-slide topography is another key factor. The back analysis process for determining the actual strength parameters of soil or a decomposed rock mass after a landslide requires knowledge of the sliding mass geometry, both before and after the sliding event. Many studies are reported in the literature about the application of back analysis for determining geotechnical and geomechanical parameters of rock and soil mass (Sakurai et al., 2003; Cepuritis et al. 2010; Frayssines and Hantz, 2009, Hussain and Stark, 2011), but they generally present little information about the geometry of the slide surface, and the weight of rock and soil mass that slid, although these factors are the most important parameters for back analysis process. Liang and Xue-song (2012) determined the slip surface having the minimum factor of safety (called critical slip surface in deterministic analysis of slopes) and the slip surface with the minimum reliability index (called critical reliability slip surface), but they have not considered the actual profile and geometry of the slide surface. Rocscience (2013) proposes the back analysis option in the Slide software for slope stability study, but it requires an imposed slide surface as input; alternatively, one can estimate by a finite element analysis the surface with the minimum factor of safety. However, this estimated surface is very likely different from the actual sliding surface, considering the uncertainties in input data of the finite element method."

Jan 1, 2015

By R. L. Bruening, L. Navarro, R. M. Izatt, N. E. Izatt, S. R. Izatt

Green chemistry principles will be discussed, and examples will be given of the use of Molecular Recognition Technology (MRT) to selectively separate valuable metals such as rhenium and palladium from various copper refinery feed streams. Recovery of these metals has numerous advantages including (i) conservation of valuable resources, (ii) prevention of environmental damage, and (iii) elimination of capital and operating expenses due to re-processing or disposal of metal-bearing streams. INTRODUCTION Refining of copper ores has a long and successful story. The history of copper, one of the first metals mined in human history, illustrates the global challenges faced as a result of increased demand for major metals and for by-product specialty metals found with them in trace amounts (Izatt et al., 2014). Copper has valuable properties, which have sustained its use over the centuries. It is an ideal material for creation of novel materials. Some desirable properties of copper that have proved valuable in our high-technology society include suitability for alloying with many other metals; ease of joining by soldering and brazing; good combination of mechanical qualities; high resistance to corrosion; suitability for many artistic purposes; and, of great importance in the modern era, efficient and economic use as a conductor of electricity. Copper mining in the U.S.A. began in the late nineteenth century in Montana (Izatt et al., 2014). The estimated total amount of copper mined globally before 1800 is about 5 million tons, four times less than is mined in a single year today (Flanagan, 2018). Production of copper in the U.S.A. has remained fairly constant at about 1,300,000 to 1,400,000 metric tons per annum from 2013 to 2017. Specialty metals such as bismuth, rhenium, molybdenum, and others that have become essential in our 21st century technology, and precious metals such as silver, gold, and the platinum group metals (PGMs) are concentrated by geochemical processes in trace amounts in copper ores. These specialty and precious metals were discarded into tailings in early mining operations, since limited extractive technologies existed and uses for most of them were limited. Thus, economic benefits for recovering them were limited, primarily, to silver and gold. Today, copper processing is the main, and often the only, commercial source for certain of these elements (Izatt et al., 2014). For example, molybdenite (MoS2) is the predominant ore mineral of molybdenum mining (Pohl, 2011). Cu-Mo-Au porphyry ore deposits supply ~75% of the world’s copper, 50% of the molybdenum, nearly all of the rhenium, and 20% of the gold. Typical ore grades are 0.5–1.5% copper, 0.01–0.04% molybdenum, and <1.5 g/ton gold. Molybdenite is the primary source for rhenium, among the rarest of metals, which is an essential component of super alloys, such as turbine blades in the aerospace industry (Pohl, 2011). Most rhenium is obtained as a by-product of molybdenite from copper mines in Chile. The case of rhenium raises an important issue. Continued availability of rhenium, selectively concentrated in copper ores, depends on continued mining and processing of copper. Since the mining company’s main interest is typically in copper production, continued recovery of rhenium and other specialty elements present in the ore body is at risk. Dependence of specialty metal supply on continued mining of major metals exists in several additional cases including indium, gallium, selenium, tellurium, germanium and bismuth (Pohl, 2011). PGMs, on the other hand, are typically mined for their own value, which far exceeds that of associated base metals. However, copper ores often contain marketable amounts of platinum and palladium, making their separation of interest, if this can be done economically.

Jan 1, 2019

By D. Lemieux

A gold bearing pyrite concentrate was treated at the pilot scale for the extraction of gold. Mineralogical analysis of the concentrate identified gold to be mainly present in the form of a solid solution in pyrite. This gold distribution resulted in a poor extraction yield of 55% by direct cyanidation. A piloting campaign including an oxidative pre-treatment by roasting in a fluid bed was followed by treatment with halogens for gold extraction has led to a gold extraction yield of 96.5%. Sulphur removal during the oxidation was very efficient at >99.5% and gold extraction by the halogens was completed within a 1 hour contact time. The piloting was performed on a 300 kg sample and uses a diluted solution of hypohalites as the oxidizing agent for gold extraction. Sulphuric acid was injected in the reactor during the halogens treatment to lower pH to 2. The diluted solution of hypohalites (1-3%) was generated by electrolysis during the piloting campaign in a membrane-less electrolysis cell. The extracted gold was recovered over activated carbon in column and the gold depleted brine was treated for impurities removal and recycled for further gold extraction. With the recycling of water and brine, the regeneration of hypohalites and with a barren solid that is inert and stable, the Nichromet Extraction technology is a green process where the protection of the environment does not preclude profitability.

Aug 1, 2013

By Douglas A. Karvonen

"Competition in the world potash market has increased significantly since the late 1970s. The failure of consumption to grow at expected levels has led to industry over-capacity, a situation which is likely to persist at least until 1990. Individual Saskatchewan producers and their offshore marketing company, Canpotex, have responded to this challenge by increasing mining efficiency, developing more cost-effective and reliable transportation systems and establishing innovative financing and market development programs tailored to customers&apos; special needs. Investment in warehouse facilities to serve U.S. customers and exploration of opportunities for intermodal distribution through the Great Lakes and the Mississippi River system have maintained individual producers&apos; position in the highly competitive domestic market.Export sales through Canpotex have been bolstered by utilization of CIDA funds, Exp ort Development Corporation financing guarantees and other innovative payment plans which enable heavily indebted developing countries to maintain the import levels which are necessary for their agricultural development.IntroductionPotash is the general term applied to various potassium salts both natural occurring and commercially derived. The most common of the commercial product s are potassium chloride, potassium sulphate and potassium magnesium sulphate. The potassium content of potash is measured in units of K20 equivalent. The common grades of potassium chloride produced for agriculture average at least 60 0/0 K20 compared with approximately 50% Kp for potassium sulphate and 22% for potassium magnesium sulphate."

Jan 1, 1985

By F. F. Roberto

Sulfuric acid has been demonstrated to be an efficient lixiviant for in situ extraction of copper in the past. It has also been proposed that microbial production (by iron-oxidizing acidophilic bacteria) of acidic ferric solution either in situ or ex situ could provide an economic strategy to generate an effective lixiviant for secondary copper sulfides like chalcocite and covellite. Copper heap bioleaching also takes advantage of this approach. One of the major environmental challenges for in situ copper recovery projects is the containment of acidic solution within the ore deposit, and ultimate restoration of the depleted ore body to its original state. A perhaps overlooked aspect of projected site operations is the possibility that transient acidic conditions and pumping of solutions from surface reservoirs into the subsurface could stimulate the growth of iron- or sulfur-oxidizing species of acidophilic microbes in the ore body, leading to additional generation of sulfate, acid, and ferric iron. This outcome would benefit extraction of copper in mixed oxide/sulfide deposits in the near term, but could complicate restoration activities. Possible impacts of pumping acidic solutions into the subsurface on microbes resident in, or introduced into the extraction zone will be discussed in the context of our understanding of copper heap bioleaching and acid rock drainage. INTRODUCTION As high-grade deposits of metals such as copper continue to decline, conventional mining methods have evolved to mine and process larger and larger quantities of ore. What is currently defined as ore today often contains less metal than the tailings of past operations. The throughput of current-day mines also leads to tremendous amounts of waste rock and tailings that may threaten the environment and communities around the mines, as has recently been experienced by 3 major tailings disposal facility (TSF) dam failures in the past 5 years. Community acceptance of large mine operations thus becomes more difficult to achieve—loss of the social license to operate. In response, the mining industry urgently pursues innovations that can fundamentally change the way in which metals are mined. In situ recovery (ISR) of metals represents one approach to a more sustainable mining industry, by virtually eliminating the need for a pit or underground excavation, eliminating the excavation and transportation of ore to a process plant and the ensuing noise and dust that is generated, and any need for waste rock dumps or TSFs. An ISR mine could have very little visible footprint beyond a network of wells, pumps, and piping to transport pregnant solution to a recovery facility, such as a solvent extraction- electrowinning (SX-EW) plant for copper. Some solid waste streams and/or storage ponds may still be necessary to treat and store bleed streams, PLS and raffinate, or as part of groundwater restoration activities. Thus capital and operating investments would be potentially much lower than that required for a conventional mine. In theory production could also be controlled to adjust to subsurface ore grade and match market demand. A not insignificant challenge of in situ recovery is the requirement for an efficient, low-toxicity, and ideally selective lixiviant for the metal that is targeted.

Jan 1, 2019

By Michael J. Beare

Requirements of both local permitting and international fundraising are forcing increasing numbers of projects in Russia and CIS to carry out dual technical studies. The principal focus of Russian mining project design is to satisfy local regulatory requirements. However, the technical documents are not generally accepted by international banks for project finance outside Russia. Similarly, international study documents are not accepted for permitting in Russia. The purpose of this paper is to compare and contrast Russian and international approaches to mine technical studies and draw conclusions from this. The Russian design and permitting system is centered around two key statutory technical documents termed the TEO Konditsy and the TEO Project. These documents are subject to regulatory approval and are broadly equivalent to the international prefeasibility study and the feasibility study respectively. A comparison of study criteria suggests similar approaches are used for the main technical disciplines in project design by the time projects are at the point of construction, but there is divergence on environmental matters where the OVOS (Russian ESIA equivalent) differs from an ESIA in some significant areas. The key differences relate to project footprint, level of technical detailed required for baseline studies, level of public consultation, consideration and disclosure of information, labour, coverage of community and social issues and the preparation of a Social and Environmental Management System (SEMS). It has been noted that the Russian Design Institutes often leave the detailed economic analysis until after the TEO Konditsy. A common problem is design teams tend to look for ?technological solutions? without due concern for project economics. The end result of this can be mines that are overcapitalized and hence sub-optimal. It can be concluded that Design Institutes have the monopoly on Russian permitting reports and this is likely to continue. Similarly, Russian institutes generally do not prepare feasibility studies to international standards and this is likely to continue to be the case. Therefore to achieve the requirement of dual technical studies, the international consultants and Russian Design Institutes will need to cooperate on a joint work program. Key issues will be to ensure the most appropriate option studies are carried out at the right stages, that project economics are considered throughout the study, and that the environmental work program covers the additional studies necessary for the ESIA.

May 1, 2009

By A. P. E. Dirige

In order to maximize the recovery of ore in variably dipping ore zones of moderate width, cemented backfill is normally placed to serve as structural support. With the intention of saving on costs, backfill of low cement content can be used, which are often supported by a sillmat of higher strength. The stability of the low cement backfill face, exposed during adjacent mining, must be carefully studied to provide very effective, safe and economic mining operations. Improper design of these stope support structures may result in fill mass failure resulting in relaxation and failure of the stope walls, with consequent losses of production, ore dilution, and in safety problems. This paper presents a study conducted to assess fill performance during adjacent pillar mining and to provide a comprehensive understanding of backfill behaviour, the failure modes that may occur and the consequences to production, ore dilution and to safety problems, and accurately predict their stability. The design study investigated the effects of stope width and height, orebody geometry and inclination, and wall roughness on the stability of cemented backfill during adjacent pillar mining. Fill properties used were based on paste fill specimens cured for 28 days. Paste fill performances were assessed based on analytical and numerical modeling studies for the different mining conditions. Analytical modeling was carried out using limiting equilibrium analysis and numerical modeling was carried out using FLAC3D. The modeling results suggested that, for stopes that are inclined with smooth wall rock conditions, backfill failure, driven by the fill self-weight, has minimum dependency on the binder content and is reduced by resisting forces developed on the footwall-fill contact. For inclined stopes with rough wall rock conditions, wall roughness contributes significantly to the stability of the backfill during adjacent pillar mining. The analytical modeling approach was demonstrated to be useful in providing some approximate parameters for predicting the behaviour of paste fill exposed faces during adjacent mining, but cannot predict the mode or mechanisms of failure. Numerical modeling not only assess the stability behaviour of paste fill free faces, but also is able to provide a better idea of paste fill failure modes and possible failure mechanisms. The depth of failure and the potential for instability for a simulated stope filled with paste fill can be predicted, and may be useful in estimating the mass of material that could possibly fail and ore dilution levels.

May 1, 2009

By G. W. H. Norman

Introduction During the past few years emphasis has been placed on the importance of major faults, fault zones, and associated structures in localizing ore deposition. This interest has developed partly through experience in mining camps in other parts of the world, and partly by the discovery of such structures associated with ore deposits in the Abitibi region, northwestern Quebec. The recognition of these structures has been brought about chiefly by detailed mapping that has been gradually extended along most of the southern gold belt of Quebec and across adjacent parts of Ontario. In the Chibougamau region of northern Abitibi, progress has been made in the mapping of major faults by using aeroplane photographs with a scale of about 1,000 feet to one inch for field mapping. These studies have shown that many large faults occur in the Abitibi region; also that there is a relationship, direct or indirect, between faults and mineral deposition. The faults are, however, of more than one type and age, and this should be clearly appreciated in any planned programme for prospecting this great region adequately. The information regarding faults and structure is so widely scattered that it is difficult to obtain a clear picture of the essential features, either for planned prospecting or for analysis and development of ideas for further study. This paper, as originally conceived, was intended only to discuss and compare the regional structure of southern Abitibi county-where detail mapping and diamond drilling have been carried on intensively for the past ten years-and of the less well-known Chibougamau district, in order that the experience gained in the one area could be usefully applied in the other. However, a comparison of the two districts leads naturally to a consideration of their common relationship to certain major late-Precambrian structures that form an important northeast system across the southeastern part of the Canadian Shield.

Jan 1, 1946

By A. Malfliet, A. Van den Bulck, D. Willems, M. Guo

The feed stock of copper fire refining processes consists of two major constituents: blister copper and high-Cu secondary scrap. A large fraction of this secondary scrap, originating from urban mining, is quite high in impurities such as Fe, Ni, Pb and Sn. Problems arise in electro-refining when these elements exceed certain limits. As a consequence, transformation of the secondary copper raw materials into high grade copper has become troublesome. However, the behavior of impurities relevant to fire refining conditions, essential for anode refineries, has not been studied in detail. Furthermore, limited research has been performed on the distribution of Ni between copper metal and slag. In this study, equilibration at 1300°C of liquid Cu-1wt.% Ni alloy and CaO-CuOx- FeOy-SiO2 slag in vacuum sealed quartz ampoules was performed for 12 hours, followed by water quenching. Electron Probe X-ray Microanalysis was employed to investigate the composition of the equilibrated alloy and slag. The distribution coefficients of Ni between slag and alloy were determined as a function of oxygen partial pressure and CaO concentration. INTRODUCTION Europe’s initiatives for a circular economy, pushing for resource-efficient ways for a sustainable future, puts Europe at the forefront of the globe. In Europe, 50% of the copper originates from recycling, being an excellent example of Europe’s circular economy (Juncker, 2018; Lacasse, 2018). High-grade copper recyclates are made available which regularly contain impurities like Fe, Ni, Sn and Pb. Aurubis Belgium is responsible for recycling these types of recyclates to anodes, cathodes and copper products. However, after fire refining of copper, the aforementioned impurities remain in the anode copper, leading to problems in electrorefining. During the fire refining of copper, a CaO-“Cu2O”-“Fe2O3”-SiO2 slag is used. Fundamental information of the distribution of impurities between the copper and this slag system is therefore essential to understand and improve the copper fire refining process at Aurubis Belgium.

Jan 1, 2019

By Georges Houlachi, Raynald Labrecque, Jean-Noël Cloutier

"Electrodialysis (ED) is an electro-membrane technology based on electrochemical process using electrical energy for the production of chemicals. The process can be used for concentrating, extracting, separating products, modifying molecules, purifying solutions, pH adjustment and regenerating salts into their base and acid. This paper reviews the principle of ED, present some of the different options and discuss applications that are relevant to the hydrometallurgy and mining industries for the treatment of effluents focusing on recovery of chemicals (acid and metals) and recycling of water minimizing the environmental footprint.INTRODUCTIONElectrodialysis (ED) is usually defined as an electrochemical separation process in which electrically charged membranes and an electrical potential difference are used to separate ionic species from an aqueous solution and other uncharged components [1]. ED technology consists of an electro-membrane technology based on an electrochemical process using electrical energy for the production of chemicals. It is a method combining electrolysis and dialysis was proposed for the first time in 1890 by Maigrot and Sabates [2]. In the late 1930s Teorell, Meyer and Sievers discussed membrane phenomena, revealed membrane potential, electric conductivity, transport number [3]. Meyers and Strauss introduced a multi-compartment ED apparatus consisting of two electrodes and a stack of ion-exchange membranes between them [1]. They succeeded to double the concentration of a KCL solution [3- Tarleton]. In general, ED consumes less energy than electrolysis to perform salt splitting. In that regard, one can expect an energy reduction of about 30% [4–5]. ED offers a great versatility in the domain of separation processes. Indeed, it can be used for concentrating, extracting, separating products, purifying by desalination, pH adjustment and regenerating a salt to acid and base components. This paper reviews the principle of ED, presents various options available and discusses potential applications relevant to the mining and metallurgy industries with economics of some successful industrial applications."

Jan 1, 2016

By J. R. del Castillo, J. Ruiz, N. Kuyucak, J. Chavez

Environmental Impact Assessment (EIA) and Feasibility Studies (FS) were carried out to evaluate the potential use of treated acid mine drainage (AMD) occurring at the Kingsmill Tunnel in the Central Andes of Peru. The 11-km long tunnel drains the underground works of the Morococha Mining District and discharges about 1.25 m3/sec of AMD directly into the Yauli River, which is located within the Amazon Basin. The communities living downstream cannot use the Yauli River water due to its low pH and elevated concentrations of metals (e.g., Cu, Zn, Fe, Mn, As, Cd) and sulfate. Studies carried out for this project included technical feasibility, EIA, economic viability and social impact assessment phases. During the "Technical Feasibility" phase, the treated AMD was produced by simulating a high density sludge (HDS) lime neutralization/precipitation process and was evaluated for various potential uses. Mining companies located in Morococha, in particular Centromin Peru S.A., and the Water Works Company of the City of Lima (Sedapal) collaborated with Golder Associates during the studies. The Canadian International Development Agency (CIDA) provided the financial assistance. The results of the physical, chemical, biological and toxicological analyses demonstrated that the treated AMD could be used for supplementing the drinking water supply of Lima and for agricultural (e.g., irrigation and livestock) and recreational purposes. Process design and scale-up parameters were also determined for the implementation of the full-scale treatment facility to the site. The use of the treated AMD as a drinking water supplement would be economically feasible.

Jan 1, 2004

By Don Peel, Jeremy Richards

Abstract - Aggregates (sand, gravel, and crushed stone) are low unit-cost products extracted in very large volumes for the construction of buildings, roads, and other infrastructure essential to modern society. Because of their low unit value, transportation costs are a key factor in resource economics, and deposits are commonly developed close to market (i.e., close to towns and cities, or along low-cost transportation corridors). This proximity results in potential conflict with residents over land use, disturbance, and pollution. Management of aggregate resources in Alberta is examined in the light of resource geology and distribution, and governance. A case history of development of the Calahoo-Villeneuve deposit is described, and the conflicts between residents and developers that led to establishment of an Area Structure Plan (ASP) are explored. The plan sets limits to, but at the same time safeguards, resource extraction, and defines terms for compensation to residents through a voluntary levy on production (Community Enhancement Fund). This fund is used to support community activities and to pay for a groundwater monitoring program. The ASP is examined within the context of the "Seven Questions to Sustainability" as set out by Mining,Minerals and Sustainable Development-North America (2002). It is concluded that the ASP, for the most part, provides a good model for conflict resolution and sustainable resource development, which could usefully be applied in other jurisdictions. The ASP was developed at a municipal level, and adoption at a provincial level would aid sustainable development of aggregate resources across the province.

Jan 1, 2003

By J. Schnarr, D. Deever, E. Johnson

"The above committee sent out a questionnaire to the gold mines for the purpose of learning what units and methods are currently in use in the mines as the first step in an attempt to agree on standard units to be used in any papers or reports that may be given to other mines or presented at meetings. The next step is to try to arrive at acceptable standard units for reporting and methods of making tests. It was suggested by Mr. J. Jardine of Eldorado Mining and Refining that the use of the metric system should be seriously considered. It was also brought out that there was no intention of having any mine change their methods to the standard for internal reporting as this would involve too much change. However for external reporting there shouldn't be too much difficulty in converting to the accepted standard units.On the following pages are the reports of those mines that replied to the questionnaire.MALARTIC GOLD FIELDS LIMITEDP.A. Coulter1. All assays - Ounces per ton2. Consumption of reagents - Pounds per ton3. Reagent strength of solutions - Pounds per ton4. Reducing Power - As described in C 0 I.L, Analysis of Cyanide Solutions5. Pulp Densities - Grams per litre6. Screen Analysis (Tailings) A sample of 150 gms is washed on a 200 mesh screen. The plus 200 mesh material is dried and ro-tapped for fifteen minutes. The plus 200 mesh portions are weighed cumulatively (the balance is considered -200 mesh) and reported in per cent."

Jan 1, 1967

By Leibniz University, D. Zapf

"The demand for gas storage operations with high withdrawal rates and operation modes different to a seasonal storage regime requires a more detailed rock mechanical consideration of thermal induced stresses in the vicinity of the caverns. This means that the change of gas temperatures during operation and the consequences of these temperature changes on the stressing of the salt rock mass must be taken into account in the rock mechanical dimensioning. Within the rock mechanical calculations a loading history, i.e. a pressure versus time dependency, has to be defined. As rock salt has a time dependent material behavior stress redistributions in the rock salt mass take place even under constant internal pressure conditions. Therefore not only withdrawal and filling periods but also the duration of phases with nearly constant internal pressure is significant for the resulting state variables. Within the paper the differences and consequences for the rock mechanical recommendations are discussed. As a result it can be concluded that recommendations with respect to minimum operation pressure as well as for maximum withdrawal rates can be answered only in connection with the respective time intervals."

Jan 1, 2015

By N. Hiroyoshi

In the leaching of chalcopyrite with sulfuric acid solutions, the copper extraction rate reaches a maximum at a given redox potential. This article reviews our studies on the determination of the optimum redox potential for chalcopyrite leaching. Shaking flask and column leaching experiments for a chalcopyrite concentrate were performed under various conditions, and the results were analyzed using a normalized redox potential defined from a reaction model assuming the formation of an intermediate CU2S from chalcopyrite. Factors, such as metal ion concentrations, solid/liquid ratio, and presence of iron-oxidizing bacteria, caused significant variations in the copper extraction versus time plots. However the copper extraction rate versus normalized redox potential plots were independent of the above factors and the copper extraction rate reached a maximum at the normalized redox potentials around 0.43. Converting the normalized redox potential to the solution redox potential gives the optimum redox potential for chalcopyrite leaching as a function of cupric and ferrous ion concentrations. This semi-empirical equation can be used to predict the optimum redox potential during leaching operation, and is useful to design the redox-controlled heap leaching for chalcopyrite.

Jan 1, 2007

By T. Yalcin

"This paper describes a process that can provide high rates of dewatering and that has the potential of bringing significant savings in tailing disposal costs. It involves a three-stage, closed-circuit operation employing a hydrocyclone, a settling cone and a thickener. The mill tailing, with adjusted pulp density, is first fed to the hydrocyclone. The underflow from the hydrocyclone goes to the settling cone for further dewatering. The overflows from the hydrocyclone and the settling cone are sent to a thickener which, with the addition of a flocculant, gives a clear liquid effluent and a dilute underflow which is recycled back to the hydrocyclone. The underflow of the settling cone is a material with as high as 78% pulp density and is suitable for direct disposal or for use as mine backfill.INTRODUCTIONDewatering is an essential process for the disposal of mill tailings and forms an additional cost item in milling operations. Cost-cutting measures are therefore desirable in this area as in any other stage of milling. One way of achieving this is through increased rate of dewatering which would require smaller dewatering units with correspondingly lower capital and operating costs."

Jan 1, 1987

By Bruce C. Smart

"Very little attention was given to the regulation of uranium mills by the Atomic Energy Control Board prior to 1974. The ore grade treated by Canadian mills in the past was in the order of 0.08 - 0.3% U and it was not difficult to keep the exposure of workers well below regulatory limits. Furthermore, uranium milling has also been substantially free of occupational illness because environmental control has been generally satisfactory (l).The discovery of higher grade ore bodies in Canada has resulted in higher radiation levels in one mill and this has partly contributed to a need for increased radiation monitoring in the mill. In addition, as greater insight is gained on the effects of radiation, the implementation of the ALARA principle is being stressed at all mills.The concept of ALARA was emphasized by the ICRP (International Committee for Radiological Protection) in 1977 and stands for '""as low as reasonably achievable'"". It is based on the premise that no proven threshold for potential effects of radiation exists and that the actual individual exposure should therefore be kept as far below the regulatory limit as possible, economic and social factors being taken into account."

Jan 1, 1982

By Frands Jensen, Erik Eriksson

"Haldor Topsoe’s Wet gas Sulfuric Acid (WSA) technology has been proven in a number of industries converting sulfurous gasses to concentrated sulfuric acid. In the metallurgical sector plants have been delivered handling SO2 gasses from copper, zinc, molybdenum, and lead ore. WSA has high energy efficiency and allows autothermal operation from feed gas strengths as low as 3.0% (volume). Recent variants of the WSA process have been developed that allow very high SO2 conversion efficiencies of over 99.9%. This paper describes the technology, its advantages and industrial achievements.The WSA technology is well suited for production of concentrated sulfuric acid of commercial quality from the sulfur dioxide (SO2) gas that inevitably emerges from the metallurgical processes. Some of the features that make the WSA technology attractive for this application are:- High SO2 conversion rates (up to 99.99%)- High energy efficiency leading to a low autothermal point (~ 3% SO2)- No need for gas cooling and drying to produce concentrated sulfuric acid- No production of waste- Very low cooling water consumptionThis paper describes the WSA process principles and highlights features that make this process attractive for handling SO2 gases."

Jan 1, 2014

By J. E. Danoczi

Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne area kimberlite field in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as ?gently? as possible since essential to the diamond liberation process is the minimization of diamond damage, particularly for the larger, high value diamonds. The Southern African diamond mines traditionally use Jaw and Gyratory crushers as their primary comminution method. However, these diamond mines generally process the harder, competent kimberlite that is located in the diatreme zone as well as the root zone of the volcanic pipe. Softer kimberlite is typically located in and around the crater area of a volcanic pipe and it is this source of kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills, this being the preferred method of comminution for minimizing diamond damage.

Nov 1, 2011