Search Documents

By M. M. Papic, J. C. Whitehead

"A sample of Hat Creek coal has been extracted using supercritical aromatic solvents in a laboratory-scale extraction unit. Extract yields in the range 21 to 27 per cent of dry-ash-free coal were obtained.These yields are significantly lower than yields available from high-volatile bituminous coal and some lignites. Thus in a combined extraction/hydrocracking scheme for the production of liquid fuels from Hat Creek coal the char product would exceed that required to supply the energy and hydrogen requirements of the process. Excess char could be used for the production of power or gas for sale.IntroductionThe Supercritical Gas Extraction (SGE) process developed by the U.K. National Coal Board operates in two stages: an extraction stage in which a coal extract is separated from mineral matter and undissolved coal and a subsequent hydrogenation stage.The SGE process is based on the ability of a compressed supercritical fluid to dissolve relatively high molecular weight substrates. It is operated under conditions where a hydrogenrich portion of the coal is selectively extracted in a short residence time extraction stage leaving a hydrogen-deficient char. The process schematic shown in Figure I illustrates that the extract produced is separated from the solvent and passed to a conventional hydroprocessing stage while the char product is utilized in the production of heat, power and hydrogen for the process. An extract yield in the order of 50 per cent dry-ash- free coal represents a ""balanced"" case for such a process in which there is just sufficient char for the provision of these commodities."

Jan 1, 1985

By M. Jahazi, J. Gholipour

Design and manufacturing of parts using hydroforming process require knowledge about material behaviour and tribological effects during hydroforming. Lubrication is one of the key issues in successfully hydroform the tubes. A Ni-based super alloy tube with 50.8 mm (2 inches) outer diameter and 0.9 mm (0.035 inches) thickness is considered for this research to study the effect of lubricants on the formability of the tubes. Hydroforming of a hollow compressor blade is considered for this project. A combination of press forming and hydroforming is employed to produce the part. LS-DYNA, an explicit dynamic finite element code, is used to model the experiments. Different lubricants are modeled using different coefficient of friction in the model. Predicted results for strain distribution at a critical section of the tube are extracted for each case to evaluate the effect of different lubricants on the process.

Jan 1, 2006

By K. Iturralde

Dense transport infrastructure areas lack green facilities, they produce annoying noise and they are big energy consumers. As far as there is no free land or space, adding a vegetal covering to existing infrastructures has become a choice in order to get a more pleasant and comfortable environment. Noise barriers are getting spread all over the highways and sometimes they install photovoltaic panels. Is this just a hype or are there real causes? A green acoustic barrier with an energy generator could be interesting for covering the existing urban transport infrastructures. The specific geometry of the infrastructures requires a personalized product. If we measure the infrastructure environment's characteristics, which are humidity, temperature, sunlight and size, we can create an accurate 3D model. This model would be used for various purposes. For instance, it could be a useful tool to design and fabricate the customized prefab acoustic barriers and plant containers. And it would be helpful for adjusting efficiently the future performance of the vegetation and photovoltaic panels. But the insertion of vegetal elements in infrastructure surroundings can be a tough operation. It requires special skills and techniques. Nowadays, those tasks are performed almost manually and they require a big effort. The prefab containers for vegetal elements would ease the robotic assembly on site.

Aug 1, 2013

By V. Pouyafar

In recent years semi-solid processing of steel alloys has gain more attention among researchers. Production of high quality complex steel parts with higher mechanical properties is the final goal for all these researches. A thorough understanding of the flow behavior of the metal under investigation is the key for a successful process design. The material used in this research is M2 tool steel. The experiments were performed using a Searl-type concentric cylindrical rheometer which is specially designed for high temperature rheological measurements up to 1500 ºC. The rheological techniques were consisted of continuous cooling experiments and isothermal holding and also shear rate step change experiments for different solid fractions. Based on the rheological data a single phase thixotropic model has been derived and adopted to the measured data. The state of the microstructure has been applied through a structural parameter. The model fits well with the experiments.

Oct 1, 2011

The PEMAC Commitment to World Class Industry in Canada The Plant Engineering and Maintenance Association of Canada PEMAC is a national, not-for-profit industry and technical association for plant and facility maintenance, engineering and physical asset management practitioners and professionals. Founded mid 80?s in the last century PEMAC is a knowledge based organization that focuses on sharing knowledge with our members and the profession. We provide education and professional development programs and certification for maintenance practitioners and professionals. We develop, produce and participate in conferences, seminars and trade shows.

May 1, 2008

By J. Jackman

North America has been aggressively pursuing approaches to improve the fuel efficiency of vehicles, and to develop alternatives to petroleum-based fuels used in automotive applications, for over ten years, Increasing energy demand due to emerging economies, coupled with probable peaking of conventional petroleum production in the coming decades are increasing the need to reduce dependence on petroleum-based fuels for transportation, Vehicle lightweighting is seen as an important strategy to improve fuel efficiency of conventional as well as highly innovative vehicles, Magnesium has recently emerged as a serious candidate for lightweighting, as a result of lower global prices, Automotive vehicles produced in North America currently use more Mg than vehicles produced elsewhere in the world, but the amounts per vehicle are very small in comparison to other materials such as steel, aluminum and plastics, The reasons, besides price, are primarily a less-developed state of technology for Mg in automotive transportation applications and lack of familiarity by the vehicle manufacturers with the material, This paper reviews the major government-funded research programs in the USA and Canada that are dedicated to advancing the state of Mg technology for automotive applications, It provides examples of research in the areas of high-pressure and other types of castings, corrosion solutions, sheet development and other wrought applications.

Jan 1, 2006

By Charles G. Kemsley

IN view of the truly remarkable development of special steels for special purposes, the mining industry has for years looked forward to a time when steel makers would come forward with a product which would be an improvement over the straight carbon steel which has always held the field for drilling rock. In order to avoid making changes in conventional shop practice, the industry has perhaps been too insistent upon obtaining a water hardening steel which could be handled in the blacksmith shop by long established methods. As early as 1932 or 1933, an oil-hardening tool-steel of the one per cent carbon, plus chrome, plus molybdenum type was applied to hollow drill steel. It was known as a hard as well as a tough steel, and one that, theoretically, should give a good account of itself as a rock drill, if properly heat-treated; and so it has proved in actual trials. There were numerous deterrents which retarded adoption of this steel. For several years there has been a constant improvement in the drilling qualities of the straight carbon steel, and, considering the higher unit price ? of the alloy, there has been considerable doubt in the minds of some mining? men as to what advantage there might be in the use of alloy over straight carbon for hollow drill steel. The alloy being an oil-hardening steel, its adoption meant having two kinds of steel in the mine, for a time, and that spelled trouble, unless some positive means of identification was adopted. The hardening and forging ranges of alloy steel being narrow also made necessary much closer control over these operations if poor results were to be avoided. These thoughts undoubtedly prevented its use becoming wide-spread, for, as a matter of actual record, less than fifteen per cent of all the hollow drill steel used in Canada today is alloy.

Jan 1, 1942

By N. Morrison, E. J. Rogans, A. J. Macintosh, N. Schoeman

"The design of carbon-in-pulp (CIP), and carbon-in-leach (CIL) adsorption circuits has essentially remained unchanged since the early days of the carbon process for gold recovery. For CIP circuit the pulp residence time is traditionally fixed at one hour per contactor with a carbon concentration of between 15 and 20 grams per litre, and the counter current carbon transfer rates are in the region of 15% pulp recycle. For CIL, the pulp residence time is usually three hours per contact or, with lower carbon concentrations ( 5 to 10 grams per litre).The drawbacks of using the counter current CIP/CIL adsorption circuits are discussed using modeling developed for CIP/CIL plant design. Counter current CIP/CIL, circuits are then compared with the carousel method of adsorption circuit design.The use of equipment suitable for the carousel approach is discussed which is, the AAC cylindrical and pumping (MPS) screens, the AAC pump-cell plant and launder designs.Finally, two plants at the Vaal Reefs Gold Mining and Exploration Company that use carousel adsorption circuits, namely the Vaal Reefs No. 1 Gold Plant, a CIL plant with stepped contactors, and the Vaal Reefs No. 2 Gold Plant, a CIP using a very short residence time (AAC pump-cell) are discussed."

Jan 1, 1998

By R. G. Gillies, C. A. Shook, W. H. W. Husband

"The current state of knowledge concerning pipeline transport of coal in water slurry form is summarized for the four categories: coal-water fuels, conventional fine coal slurries, coarse coals and stabilized mixtures of coarse and fine particles. Surface chemistry is of dominant importance for coal-water fuels and considerable progress in understanding the role of surfactants has been achieved in recent years. Little generalized research on the flow of conventional fine coal slurries has been done in the past 17years, although innumerable conceptual designs and feasibility studies have been undertaken. Coarse coal slurries are fairly well understood but the model which explains their flow requires more data to be established fully. Stabilized flow mixtures should probably obey the same model as coarse coal slurries but experimental results for stabilized mixtures have not yet been incorporated in a comprehensive theory.IntroductionPipeline transportation of coal in a water vehicle has been employed for many years in coal washeries. It has been used less frequently in hydraulic mining and thermal power station fuel supply systems. The suitability of coal for pipeline transport arises from its moderate specific gravity relative to the carrier fluid and the fact that throughputs are often large and steady over long periods of time."

Jan 1, 1990

By Ken McClure, Alex Day

Located North of Williams Lake British Columbia, Gibraltar Mine is the fourth largest open pit Copper mine in North America. Gibraltar commenced Copper concentrate production in 1972 with a mill throughput rate of 30,000 tons per day. A series of expansion projects, including installation of a second SAG mill with variable speed drives in 2013, has increased mill throughput to 85,000 tons per day. Over the past 24 months, Gibraltar Mine in partnership with Spartan Controls has executed several advanced process control programming projects culminating in the implementation of a Continuous Speed Controller (CSC) for the most recently installed SAG mill. This paper covers development and results for the SAG mill speed controller. INTRODUCTION In January 2016, the price of Copper fell below $2.00 USD per pound, the lowest price in 7 years. Gibraltar Mine faced a significant challenge; how to maximize profit in an environment where capital spending was not an option. An opportunity was quickly identified to improve performance through increased automation and advanced control of the grinding processes. Beginning in March 2016, Gibraltar Mine partnered with Spartan Controls to introduce Advanced Process Control (APC) to the grinding circuits. The collaboration between metallurgical and process control engineering disciplines proved to be effective for achieving gains in throughput, reliability and productivity for the mill process. The Gibraltar milling facilities include 2 grinding-flotation plants for concentration of chalcopyrite ore with throughput rates of 58,000 tons per day (Concentrator 1) and 38,000 tons per day (Concentrator 2). Each of the two concentrators has a 34’ diameter SAG mill powered by 2 GE 4800 kW synchronous electric motors. For SAG 1 (in concentrator 1), power is transmitted through 2 Eaton Airflex clutches. For SAG 2 (in concentrator 2), the motors are driven by 2 TMEIC Variable Frequency Drives (VFDs). All programming is done using DeltaV, which Gibraltar uses as its Distributed Control System (DCS) and Human Machine Interface (HMI).

Jan 1, 2019

By M. J. Brodie

"The decision to proceed with mine decommissioning, generally involves a number of complex and independent factors. These factors, including potential for re-opening, legal requirements, contingent liability, asset depreciation, due diligence, and public relations are discussed in the context of the financial implications on a net-present- value basis. It is concluded that the decision to delay mine decommissioning is commonly not in the best financial interests of the mine operator. Some measures to reduce decommissioning costs and expedite the process are presented.IntroductionThe primary audience for this paper is mining executives, although it should be of interest to all professionals involved in the planning and carrying out of mine decommissioning. Historically, mines were abandoned, not decommissioned. Then, as decommissioning became required, it was assumed that salvage revenue would pay for decommissioning. During the I980s, it became apparent that mine decommissioning costs would exceed salvage revenue for nearly all sites, and that a substantial net cost for decommissioning would be realized for some sites. Throughout this period, the approach to decommissioning has evolved through the sequential addition of measures to meet the increasing regulatory burden. This has resulted in a process in which the elements of decommissioning may not be optimized with respect to each other for the most favourable net present value to the corporation. Additional considerations which are not specific to mine decommissioning, such as environmental policy, due diligence and public relations, may now come to bear on the decision-making process.This paper addresses the issue of mine decommissioning as a three-step process. The first step involves identification and evaluation of all of the issues that relate to mine closure, the most importantof which is the potential for re-opening of a mine. Assuming that it is decided that a mine is unlikely to re-open, the second step is to determine when to carry out the decommissioning work. This aspect is examined through a net present value (NPV) approach. Finally, details regarding who does the work and how the various tasks are divided up must be resolved.Every mine is a unique concentration of minerals at some specific location, hence the development, operation and closure of a given mine must be regarded as a special case. Superimposed on the site-specific considerations are the size, history and financial status of the associated corporation."

Jan 1, 1995

By B. Andreaus

In spite of tremendous efforts in research and development of polymer electrolyte fuel cells (PEFCs), essential properties of the actual catalyst material, supported Pt or Pt-alloy nanoparticles, are not yet well understood. Fundamental understanding of the catalyst structure and the prevailing kinetic mechanisms is, however, of utmost importance for further progress. In the present study, we investigate catalyst activity for CO oxidation from a theoretical point of view. Electrochemical CO oxidation serves as an important test reaction for the study of the fundamental properties of supported Pt nanoparticles. Recent experiments have revealed strong effects of catalyst particle size and supporting material on catalytic activity. It was found, that the activity towards CO oxidation decreases significantly when the particle diameter drops below 2.5 nm. We perform kinetic Monte Carlo simulations of CO oxidation on supported catalyst particles to elucidate this particle-size effect. The simulations are based on the active site concept, highlighting the role of active site formation and finite surface mobility of adsorbed electroactive species for catalyst activity. For comparison with experimental results, potential step experiments were simulated. The Monte Carlo simulations consistently reproduce effects of particle size and electrode potential found experimentally. In comparison with our simulations, analytical mean field models and nucleation and growth models exhibit inferior agreement with experimental data. In summary, our findings support an oxidation mechanism via active site formation. The reason for the slow reaction kinetics on catalyst particles with diameters below 2.5 nm is a rather low CO surface diffusivity. The rates of active site formation, diffusion and CO oxidation via recombination with adsorbed OH can be determined from the simulations.

Jan 1, 2005

"Industry Guide 7 contains the Securities and Exchange Commission’s basic mining disclosure policy. It provides guidance for Registrants on various matters including the definition and disclosure of proven and probable reserves and the definitions of exploration, development and production stages. The definitions and disclosure instructions contained in this Guide apply to all public mining entities and their public disclosures. As NI 43-101 is law in Canada, the SEC allows mineral resources and mineral reserves prepared under CIM Definition Standards for issuers that are reporting in Canada but are also registered with the SEC. The SEC places conditions on the disclosure of these estimates. US shareholders are cautioned that the requirements under NI 43-101 and the CIM Definition Standards differ significantly from those of Industry Guide 7.Note: this Guide contains the Commission's basic mining disclosure policy. The definitions and disclosure instructions contained in this Guide apply to all public mining entities and their public disclosures pursuant to the rules of Regulation S-K. Questions regarding the application of these definitions and rules to specific situations should be asked of the Commission's mining engineers or geologists at either the Office of Engineering, Division of Corporation Finance, 202-272-3252, or the Branch of Geology, Central Regional Office, 303-844-1000.(a) Definitions. The following definitions apply to registrants engaged or to be engaged in significant mining operations:(1) Reserve. That part of a mineral deposit which could be economically and legally extracted or produced at the time of the reserve determination.Note: Reserves are customarily stated in terms of DoreD when dealing with metalliferous minerals; when other materials such as coal, oil shale, tar, sands, limestone, etc. are involved, an appropriate term such as Drecoverable coalD may be substituted.(2) Proven (Measured) Reserves. Reserves for which (a) quantity is computed from dimensions revealed in outcrops, trenches, workings or drill holes, grade and/or quality are computed from the results of detailed sampling and (b) the sites for inspection, sampling and measurement are spaced so closely and the geologic character is so well defined that size, shape, depth and mineral content of reserves are well- established.(3) Probable (Indicated) Reserves. Reserves for which quantity and grade and/or quality are computed from information similar to that used for proven (measured) reserves, but the sites for inspection, sampling, and measurement are farther apart or are otherwise less adequately spaced. The degree of assurance, although lower than that for proven (measured) reserves, is high enough to assume continuity between points of observation.(4)(i) Exploration StageDincludes all issuers engaged in the search for mineral deposit (reserves) which are not in either the development or production stage."

Jan 1, 2003

By Russell F. Palmer

"THE PRACTISING MINING ENGINEER has little time for the expression of opinion on abstract questions concerning the definition and future of mining engineering. The following comments indicate some of the thoughts and suggestions of those who have found mining engineering a very satisfying field of endeavour. The future of mining engineering has been under discussion for perhaps twenty years. It is significant that the University of Saskatchewan program was in- 88 traduced at the time that some traditional mining schools were questioning the need for mining engineers. One Canadian university, and some American schools, actually abandoned the field at this time, some ten years ago.Five years ago, Mining Magazine sponsored an international debate on training for the future, and concurrently, the CIM undertook a major survey of the mineral industry's manpower needs. The current CIM discussions should prove more fruitful, as they are directed toward mining engineering alone, rather than the broad, and confusing, spectrum of all professionals and semi-professionals of the mineral industry."

Jan 1, 1972

By Dina Aloi

The need to be seen as responsible neighbours and good corporate citizens is a critical success criteria for mining companies. To be seen as responsible requires both achieving responsible performance, and making that good performance visible to the community, legislators, investors, and other stakeholders. This has broadened the skills required for the successful operation of a mining company to include social sciences, public affairs, communications, and environmental sciences. Mining companies still look to technical specialists to achieve the core of that good performance - broadly characterized as a sustainable operation. However, the degree of understanding that those specialists have of the requirements for sustainability and overall Corporate Social Responsibility has a tremendous impact on the overall performance of the project and company. In her keynote address to the Sustainability for Profit session, Dina will outline some of the key areas in which technical employees and consultants can contribute to achieving successful sustainable mining operations.

Jan 1, 2010

By G. A. Campbell

This paper looks at how changes in the economies and demographics of the eight largest copper-consuming countries have been affecting their consumption of copper. The period of 1976 to 2005 is considered. Annual changes in measures like intensity of use of copper, per capita consumption of copper, copper consumption based on per capita income, and copper consumption from industrial production for each country and in aggregate are calculated. Other factors like the change of industrial production relative to total GDP and population/age trends are also considered for the individual countries. Non-parametric and parametric statistical tests are used to determine the significance of observed trends and relationships for individual countries and in aggregate. The results give insights into how copper consumption is changing for the countries and what economic/demographic factors are driving these changes. These insights provide some guidance about where copper consumption trends are headed in the future.

Jan 1, 2007

By Jamie W. Pardy

The objective of the Canadian International Development Agency program is to facilitate the efforts of the people of developing countries to achieve self-sustainable economic and social development in accordance with their needs and environment. The British Columbia Ministry of Energy and Mines (BCMEM) is the executing agency for the four-year Peru Minerals and Metals Public Sector Assistance Project which began in December 1998. The primary beneficiary is the Ministerio de Energía y Minas del Peru (PMEM). The project is designed to address mine health & safety, environmental management and mineral resource information. Project activities currently underway include joint development of: an inspection system, a mine rescue system, an enhanced and e-Commerce capable mineral information website, environmental guidelines for industry and standardized ministry evaluation criteria for environmental impact assessments and closure plans. In addition, reports on management options for mineral concentrate transportation, storage and handling, and on mine reclamation security policy have been delivered at workshops.

May 1, 2001

By T. Nagasaka, T. Miki

Suppression of CO2 and waste such as slags discharged from iron- and steelmaking processes are some of the typical major issues for the protection of global environment and sustainable growth of steelmaking industry. Utilization of active phytoplankton growth will be one of the best options to stabilize and suppress carbon dioxide at high-efficiency. Inorganic minerals such as C, 0, N, Si, P and Fe are necessary for phytoplankton multiplication. It is crucial for supply of nutrition into seawater effectively for phytoplankton multiplication to understand the dissolution behavior of some elements from steelmaking slags into seawater. The morphology of the precipitated phases in steelmaking slags during cooling period was investigated in the present work. The dissolution behavior of some elements from steelmaking slags into artificial seawater has also been studied. The effect of nutrient dissolved into seawater on phytoplankton multiplication, some examples of marine structure made from steelmaking slag, and estimation of CO2 fixation amount by marine phytoplankton are also discussed.

Jan 1, 2004

By Masatake Haruta

Gold can be deposited as nanoparticles on a variety of support materials by coprecipitation or deposition-precipitation of Au(OH)3, grafting of organo-gold complexes such as dimethyl-Au(III)-acetylacetonate, mixing of colloidal Au particles, and vacuum deposition. Owing to the moderate adsorption of at least one of reactants (for example, CO) on the edges and corners of Au nanoparticles and to the activation of the counter reactant (for example, O2) at the perimeter interface with the supports, supported Au nanoparticle catalysts exhibit unique and practically useful catalytic properties at relatively low temperature below 473K. They have already been commercially used for deodorizers in rest rooms in Japan and will find growing applications in indoor air quality control, pollutant emission control, production of hydrogen energy carrier, and innovations in chemical processes. Cluster science of Au may also open an exciting area of research showing some magic numbers for dramatic changes in reactivity.

Oct 1, 2003

By J. W. Merks

"The accuracy of a measurement on minerals and ores can be assured by applying suitable and unbiased procedures but its precision is a function of the number of primary increments and their mass, the number of lots per consignment or samples per shift, and the number of measurements on analysis fine samples.Experimental data will be used to show how the variance components for sampling, sample preparation and analysis contribute to the total variance on which precision statements for the final measurement are based. This type of experiment should not only form part of quality control programs at mines and smelters, but also underly the criteria on which the design of manual sampling regimes and mechanical sampling systems for bulk solids and slurries should be based.Sampling systems and regimes can only be adjusted and optimized if the variance component for each step in a quality evaluation process is measured. Knowledge of precision characteristics lies at the core of effective loss prevention and control programs."

Jan 1, 1985