Search Documents

By E. L. Martheleur

A general expression for the electric power generated or consumed in a direct-current circuit is obtained by multiplying the reading of a suitable voltmeter connected across the terminals by the reading of an ammeter connected in the circuit. by the reading of an ammeter connected in the circuit. When alternating currents are considered, the product of the volts and amperes as obtained for direct currents does not generally represent the true energy involved; it is greater than this true energy and should be multiplied by a certain factor which may have any value between zero and unity, according to the conditions of the circuit. This factor is called the power-factor of the system, and expresses the ratio of the true energy over the apparent energy. For a three-phase system the expression of the apparent energy is [\/ 3 x E x I; ] while the expression of the true energy, that is, energy suitable for mechanical work, is [v? 3 x E x I x cos A.] The total current of a circuit corresponds to the reading of an ammeter connected in the circuit; it is the resultant of two currents. The first of these is in phase with the voltage, and is that portion which really produces mechanical work; the second is always in quadrature with the voltage, that is it may lead or lag the voltage by 90° according to the condition of the circuit. This second current does not produce any sensible work, and for this reason is sometimes called wattless current or reactive current.

Jan 1, 1924

By J. E. Udd, L. B. Geller

"Responding to requests by the Canadian mining industry and the mine regulatory authorities, the Canada Centre for Mineral and Energy Technology (CANMET) undertook a major research project on evaluation of wire rope testing in 1986. The objectives were to document, analyze, and clarify - in basic operational terms the reasons for ongoing mine shaft wire rope failures that occur despite mandatory non-destructive testing (NDT) with electromagnetic (EM) instruments on a routine basis.The project's investigative scope and depth was unprecedented. It could not have been successfully completed without the wholehearted cooperation of industry, research organizations, and mine-inspectorates at both national and international levels.The project's goals were attained. II was shown that, at present, the problem areas in Canada are oj a human , rather than of a hardware-related nature. Consequently, the principal recommendations are concerned with a more widespread, more uniform and thorough operator training and certification process at industrial and regulatory levels. Secondary suggestions concern areas of hardware-related improvements.In this paper an up-to-date general overview is given of the major project results. A n extensive reference list is also provided of papers that contain all relevant documentation in detail."

Jan 1, 1992

By B. R. Rakishev

Balanced development of mining works at all the benches of a working zone by use of the excavator-automobile complex is achieved by transition to the technology of the bench excavating with cross panels by the two-sub-bench scheme with the changing levels of the working platforms (is patented in Kazakhstan). In deep quarries realization of this technology will allow to reduce the current volumes of the stripping ore excavation by 10?15 % and more, to increase the opened reserves of minerals by 20?50 % to decrease volume of mining-capital works for construction of stripping excavations by 2?4 times and to provide efficient use of powerful excavator-automobile complexes.

Aug 1, 2013

By Wei Wei

Mining induced ground movement and/or stress redistribution could cause ground instability issues. This is particularly true when the extraction of large stopes is done with one or two large production blasts. Often enough, it is the nearby mine development like haulage drifts and cross cuts that are influenced the most by production blasts. Proper and timely mitigation of ground control issues due to stress redistribution is required. This is usually done by drift rehabilitation involving the installation of secondary support system in the affected areas of the mine development which include; slashing, wire mesh, and in some cases the use of shotcrete liners. It is imperative that such rehabilitation be implemented to the mine infrastructure in a timely manner in order to avoid aggravated ground control problems and production delays. If the real time performance of the support system is captured, it would be possible to determine the timing for rehabilitation job. Birchtree Mine in Thompson, at the Vale Manitoba Operation, has begun mining the 84 Deep Orebody. One of the identified risks is the stability of the crusher room under mining induced stress redistribution. It is proposed to use the U-Cell technology to monitor the primary support system performance (rebar bolts and extension bolts) and monitor the real time performances of the bolt axial loads. The U-Cell technology is a 7-inch long, coupler load cell that is screwed onto the threaded portion of a rock bolt prior to installation. Rehabilitation in the vicinity of the crusher area where U-Cells are installed is recommended when the bolts have reached 70% of their yielding capacity. Catastrophic ground failure can be avoided by adding secondary support in a timely fashion. This paper presents a case study at Birchtree Mine in Thompson Manitoba, where the performance of primary ground support system is monitored and recorded during production.

Jun 1, 2012

By W. G. Brown

"Review of prototype testing of two types of three-phase, argon stabilized reactor/furnace indicates specialized advantages for both, as compared with existing metallurgical furnace technology. They are: the direct-arc, plasma-torch furnace (Knipp); and the indirect, plasma extended-arc reactor (PEAR), developed at the University of Toronto.IntroductionA unique type of three-phase AC, plasma extended-arc reactor, (PEAR), shown in Figure la with gravity feed, has been undergoing development at the University of Toronto, during the past fifteen years: argon gas, introduced axially through drilled-holes in ordinary graphite electrodes, increases the length of indirect arcing and improves electrical stability while decreasing electrode consumption as compared with the performance of AC electric arc furnaces (EAF 's). Meanwhile and independently, a three-phase, transferred arc plasma furnace (Fig. 1b) has been developed by the Krupp Research Institute in Germany, using argon-stabilized, water- cooled plasma-torches with thoriated tungsten electrodes.Accordingly, the two types of furnace are similar as to both three phase and stabilized operation, but otherwise they differ in several respects, ranging from indirect versus direct-arcing to principal intended application and current state of practical development. Between them they raise questions: (I) of their present or fore seeable economics in comparison with existing processes they are intended to replace , (see Heinke and Neuschutz, 1986, for a review of the merit s of AC and DC plasma-torch furnaces); and (2) of the state of development and accessibility of their plasma theory-in-common."

Jan 1, 1991

By A. Eslami, H. Tabatabaei, M. Kolandoozan, Z. Manafi, A. R. Shahverdi, M. Noaparast, M. Oliazadeh

Application of Acidithiobacillus ferrooxidans bacteria to flotation of Sarcheshmeh low-grade copper sulphide ore was studied. Sarcheshmeh low-grade ore contains pyrite, which causes some problems in the flotation of copper minerals. In this study, A. ferrooxidans was used to change the surface chemistry of pyrite and copper sulphide ores and consequently, their flotation behaviour. In the presence of A. ferrooxidans and xanthate as a collector, pyrite was depressed whereas chalcopyrite and other sulphide minerals were unaffected. In addition, the pulp pH remained unchanged. It was shown that the surface chemical properties of the bacteria can be manipulated successfully to achieve the desired effects in a flotation process. The results showed that the recovery of pyrite in the presence of the bio-depressant is 50% lower than when no bacteria were present. At the same time the recovery of chalcopyrite remained unchanged.

Jan 1, 2004

"THE PACIFIC CONTINENTAL MARGIN OF CANADA is de-fined, for the purposes of this paper, as the area sea-ward from the present mainland coast of British Columbia to the foot of the continental slope. It thus coincides with A. Sutherland Brown's Insular Tectonic Belt. The region is limited to the north and south by the political boundary with the U.S.A., the location of which is still in dispute.The region can be subdivided into: (1) an interior trough comprising the Queen Char-lotte, Comox and Nanaimo basins; (2) a medial uplift comprising Vancouver Island and the Queen Charlotte Islands; and (3) a marginal shelf which is extremely narrow (Jess than 5 km) west of the Queen Charlotte Islands, widens to 160 km in Queen Charlotte Sound and is about 35 km wide west of Vancouver Island, where it is underlain by the Tofino sedimentary basin, with its• extension, the Juan de Fuca Basin, at the southern end.The medial uplift consists of a highly disturbed anticlinorium of mainly Mesozoic rocks, with a core of Palaeozoic. The rocks include thick sequences of eugeosynclinal volcanics and sediments. There is strati-graphical evidence of repeated interruption in sedi-mentation. By late Jurassic, the main eugeosynclinal phase was over and a successor basin was initiated in the interior' trough. This became filled, during Cre-taceous and Tertiary time, with sediments ranging in environment from bathyal turbidites to terrestrial conglomerates and coals. West of the medial uplift, another successor basin developed in early Tertiary times and became filled with mainly deep-water marine sediments. A third effusive sequence marks the base of the Tertiary on Graham Island and over most of the Hecate Strait region and Tofino Basin."

Jan 1, 1970

By M. R. Swaan, G. J. Stewart

"ABSTRACTThe application of failsafe techniques to ask the ""What if"" questions about any process has been well established in the chemical industry for many years. The unusual number of fatalities that occurred in Ontario during 1986-87, prompted Inco management to look at the Fail Safe techniques as a method of improving safety performance.INTRODUCTIONOne of the major areas at any time for potentially disastrous accidents is the shaft, where all men and materials must travel. In April 1987, Inco's Thompson Mine's first Fail Safe Team was established to look at its shaft operations. The initial group of eight people was made up of hourly equipment operators, mine foremen, engineering, maintenance and the superintendent. This group took the name of Shaft Risk Analysis Team or SRAT.The many tasks or jobs that are performed in a shaft prompted the team to divide the work under six major headings; slinging, moving men, skipping, dewatering, shaft inspections and moving materials. Each of these areas contained many different tasks which are interrelated. The only way to understand this interrelationship was to flow chart the steps that actually occur in getting any job done.The flow charting is done by the foreman and operators using existing standard manuals and their experience of what actually takes place. In many cases, it soon became apparent that they had been ""working around"" many problems created by their standards. Fine tuning of these flow charts takes place at the weekly meetings, where input from all involved leads to a better understanding of the actual job being analyzed and its potential hazards. Two major points need to be emphasized in getting good flow charting at a mine:I. It must never be blame oriented or you will never discover how the jobs are actually done and hence you won't know what to improve.2 . All team members must have equal voting rights in deciding how to put the charts together so that they have ownership of the finished product. It is far too easy to end up with amanagement view of the way it should be. Many different techniques or methods are being employed to improve the tasks and reduce the risks associated with any job once the basic flow chart is established. The ones found to be the most useful are highlighted."

Jan 1, 1989

By Louise Grondin

Laronde Mine has been working for a number of years to identify substances that could contribute to process water toxicity and to find an effective way of removing these contaminants from the water. Initial studies have identified ammonia, nitrite, cyanide, thiocyanate, cyanate, dissolved organic carbon, copper and zinc as potential toxicants. Bench-scale tests were carried out with Lakefield Research to find a water treatment process that could effectively remove the suspected toxicants. Nine treatment processes were evaluated: 1) granular activated carbon (GAC) filtration followed by zeolite, 2) zeolite filtration followed by GAC filtration, 3) aeration followed by GAC filtration, 4) multi-stage GAC filtration, 5) chlorination followed by dechlorination, 6) addition of clay based polymer, 7) treatment with peroxide and ultra-violet light, 8) bulk addition of GAC and zeolite powder, 9) treatment with bacteria. This article presents a summary of the test results and of the problems associated with the evaluation of technologies for the treatment of toxicity.

Nov 1, 2002

By David Morrison

Our present longwall problems in Cape Breton can be grouped under five main classifications. These are: (1) Roof control on the face and on the main roadways leading thereto. (2) Transportation of coal along face and levels. (3) Mechanical loading at the face. (4) Safe method of conducting and applying power at the working faces. (5) Dust nuisance. The usual layout for longwall operation in Cape Breton is to have three, and sometimes four, faces in line with each other, the length of face being from 400 feet to 500 feet (see Figure 1), and producing between 425 and 500 tons per face. Each wall is serviced by a well constructed roadway for transportation of coal, men, and materials, and is operated as an independent unit. Each wall works under a regular cycle of operations: first, cutting and boring; second, drawing hardwood chocks, building midwalls, and shifting panlines; and third, loading. The present method of roof control and operation of longwall faces has developed through trial and error since the commencement of longwall miring in Cape Breton. The basic method of roof control in all longwalls in Cape Breton is: rigid support of the roof in the immediate vicinity of the working faces by hardwood blocks, as shown in Figure 2, accompanied by a cushion support furnished by continuous midwalls, 12 feet wide, constructed of stone obtained from the waste and spaced at 50-foot centres. These midwalls are kept forward to within 4 feet to 10 feet of the working face and allow a gradual subsidence of overhead strata, thus preventing any sudden break at the working face.

Jan 1, 1947

By B. Hart, D. J. Miller, J. T. Francis, M. C. Biesinger, Smart. R. St. C.

Diagnosis of the surface chemical factors playing a part in flotation separation of a valuable sulfide phase requires measurement of the hydrophobic and hydrophilic species that are statistically different between the concentrate and tail streams. Time of flight secondary ion mass spectrometry (ToF-SIMS) can be used to identify sufficient particles of a specific mineral phase for reliable statistics determining a mean value for each species with 95% confidence intervals (1). Using the region of interest (ROI) facility in the Tof-SIMS software, a mass spectrum from each particle, at 1-2 monolayer sensitivity, is recorded and stored. This analysis is reported for a chalcopyrite / pyrite / sphalerite mineral mixture conditioned at pH 9 for 20 minutes in order to study transfer of copper from chalcopyrite via solution to the other two mineral surfaces since this mechanism can be responsible for their inadvertent flotation in copper recovery. Analysis from mineral selection based on specific ToF-SIMS signals (eg. Pb, Zn, Cu, Fe, Fe/Cu) indicated no statistical difference in the copper intensities on pyrite and sphalerite after this conditioning. Principal component analysis (PCA) of the ToF-SIMS imaging data identifies combinations of factors strongly correlated (positively or negatively) in images or spectra from mass spectra recorded at each of 256x256 pixels in a selected area of particles. PCA is a better method of selecting minerals due to multi-variable recognition. It has clearly separated a statistical difference in copper intensities between the sphalerite and pyrite phases. The method has been extended to samples from an operating plant again with excellent phase recognition and diagnostic surface chemistry.

Jan 1, 2004

By Zou Lisheng

The culture of safety is very important to coal mining production. About 90% of mine accidents are caused by human error. This paper analyzes the status of China?s coal mining accidents, and accident cause. This paper explains the concept of safety culture, the value of safety culture, as well as the relationships between safety culture and safety behavior, and between safety culture and science and technology. The paper proposes the model of safety culture and the ways to enhance safety culture of coal enterprises. Safety culture and safety production is closely related and are significant to the improvement of mine safety situation in China.

Aug 1, 2013

By G. E. Bogin, C. Strebinger, J. F. Brune

"Evidence shows that methane gas emanates from the mined-out area or gob of a longwall coal mine and can travel towards the working face, posing an explosion risk. Since the gob consists of varying levels of compacted rock, many researchers have modeled fluid flow through the gob as a Darcy-type porous media with a specified porosity and permeability. When studying methane gas explosions near the gob fringe, the Darcy flow assumption may not be applicable to describe the methane flame interaction with the gob. Computational fluid dynamic studies were performed modeling methane flame propagation across a simulated gob which was modeled as both a Darcy porous medium and as discrete rock objects with varying sphericity. Modeling the gob as a Darcy porous medium results in unrealistic methane flame propagation since the porous media assumption does not consider any differences in rock size and/or distribution. Additionally, the porous media model does not allow for ignition within and subsequent flame propagation through the porous medium, which must be modeled to understand the potential for methane gas explosions in the gob area. Modeling the gob as discrete rock objects produces more realistic methane flame dynamics and agrees with experimental observations. Modeling results show flame propagation across circles, hexagons, and squares, meant to represent rock rubble in the gob, produce different levels of turbulence which affects methane flame propagation velocity. This research demonstrates that modeling methane gas explosions in a longwall coal mine environment, specifically near the gob area, requires modeling obstacles, such as rock rubble, as discrete physical objects to capture the complex coupling of fluid dynamics, thermodynamics, and heat transfer. INTRODUCTION Although there are methods to mitigating methane accumulations in a longwall coal mine, explosive gas zones (EGZs) of methane and air may exist and pose an explosion risk to nearby miners and equipment (Brune, 2014) (Karacan, Ruiz, Cote, & Phipps, 2011). In the event of an explosion, the resulting methane flame and pressure wave can be catastrophic as evidenced by the Upper Big Branch explosion in 2010 that killed 29 miners (Page, et al., 2011). Since the mining process is transient, it is difficult to determine exactly where these EGZs exist, but investigative reports show in many cases, these EGZs can be near the working face, behind the shields, or within the gob area (Brune, 2014) (McKinney, et al., 2001). Additionally, miners have recounted seeing flames moving back and forth within the gob and under the roof supports (McKinney, et al., 2001) and in other cases, anecdotal evidence of hearing small pressure pops deep within the gob area (Brune, 2014)."

Jan 1, 2019

By I. P. Swainson, A. Ilbagi, H. Henein

Powders of Al-50wt%Ni, Al-40wt%Ni and Al-36wt%Ni were produced using the Impulse Atomization technique, a rapid solidification technique. The molten droplets were cooled in-flight by the stagnant helium or nitrogen in the atomizing chamber. The resulting powders were sieved into different size ranges. X-Ray diffraction and neutron diffraction were used in order to quantify the phase fractions in the samples. The computer software GSAS was used to calculate the weight fraction of the existing phases, namely Al3Ni2, Al3Ni and Al, by profile refinement method. The effect of processing parameters, alloy composition and particle size will be discussed in this paper. In brief, no AlNi was found in any of the samples analyzed. Higher cooling rates resulted in the reduction of the ratio of Al3Ni/Al3Ni2. Also, at high cooling rates, Scheil closely predicted the ratio of Al3Ni/Al3Ni2. Some metastable phases were found in Al- 36wt%Ni.

Jan 1, 2010

By Lin Li, Ahmad Ghahremaninezhad

"In this paper, the electrochemical behavior of ferric and ferrous couple on the pyrite surface was studied by application of the chronoamperometry technique in an acidic solution at room temperatures and atmospheric pressure. The effects of the pyrite origin, ferric and ferrous ions concentration on the electron transfer kinetics of Fe3+/Fe2+ reaction were probed. Tafel behavior of all the test conditions were developed. The results showed that the ferric-ferrous reaction on pyrite electrodes with different origins have a common mechanism, despite different reaction kinetics. The exchange current densities of the redox reaction have the same magnitude of about 10-5 A·cm-2, which is far lower than the value reported for the gold and platinum electrodes, but larger than that of the chalcopyrite electrode. The cathodic transfer coefficients are between 0.4 and 0.5, while the anodic transfer coefficients appear unusual with the lowest value being 0.23. It was also demonstrated that an increase of one order of magnitude of iron concentration has no clear effect on the exchange current density and cathodic transfer coefficients of Fe3+/Fe2+ redox reaction.INTRODUCTIONPyrite, FeS2, is mostly considered as a gangue mineral which frequently coexists with valuable minerals and metals, such as gold, copper and nickel. Its separation from valuable minerals can be a costly process (Chandra & Gerson, 2010). In refractory gold ores, the fine gold particles are locked inside the pyrite structure. Oxidative leaching of pyrite is a hydrometallurgical method to destroy the structure of pyrite and expose the fine gold particles to the cyanide solution in the downstream cyanidation circuit. Pyrite oxidative leaching can be achieved by oxidation of pyrite via oxygen and ferric ion(McKibben & Barnes, 1986). In fact, pyrite oxidation by oxygen and ferric is a significant source of acid mine drainage(AMD), which adversely causes serious environmental problems(V. P. Evangelou, 1995).The pyrite oxidation mechanism is accomplished in three consecutive steps: (i) pyrite is oxidized by oxygen and ferrous ion formation (Eq. 1); (ii) ferrous oxidation by oxygen and ferric ion formation (Eq. 2); (iii) pyrite oxidation by means of ferric ions (Eq. 3). Hence, both oxygen and ferric participate in the pyrite oxidation process (Moses & Herman, 1991):"

Jan 1, 2016

By Xue Yang

Even though many approaches have been proposed for automated fault detection and diagnosis of Heating Ventilation and Air Conditioning (HVAC) systems, and advanced maintenance programs, such as preventive and predictive maintenance have been applied for the systems, issuing work orders for corrective maintenance is still a reality. Currently corrective maintenance still accounts for more than 55% of all maintenance programs in average facilities in the US (DoE, 2010). Indoor air related problems are especially important among corrective maintenance work orders. This paper provides details of a case study conducted to capture the workflow that HVAC mechanics follow, their rationale in diagnosis process and the information they typically refer to while responding to indoor air related corrective maintenance work orders. The general workflow for HVAC mechanics to complete such types of work orders was summarized into 5 stages, and generic information requirements recorded from the case study were synthesized. Initial findings show two main challenges in the industry for HVAC mechanics to get access to required information, which highlights the need for a systematic approach that would enable identification of such information applicable to a given context under which a work order has been generated and provide values of required information for HVAC mechanics to do sound diagnosis through integrated data repositories.

Aug 1, 2013

By J. Y. Liu

In Comparison to the application of HPGR (high-pressure grinding rolls) in the cement industry and in iron ore processing, the introduction of this energy-efficient comminution technology to processing of nonferrous base-metal ores has progressed slowly as yet. In the field of minerals industry, challenges lies not only in the large variety of the feed material with respect to particle size, density, hardness, moisture and mineralogy of the material but also in complexity of the processing flowsheet, which need to be addressed from case to case based on result of HPGR comminution test work. Whereas conventional comminution test with HPGR in lab-scale or pilot scale needs quite a large amount of feed material, a compressive stressing test of particle-bed in piston-die device provides an effective way to study interparticle breakage behavior of ore material with much less feed. In the present study the effects of interparticle breakage on comminution of a copper ore has been investigated by compressive stressing of particle bed in a piston-die device. The feeds to the particle-bed stressing tests were four narrow size fractions in the size range of 0.3~3.35 mm and a broad size fraction of 0/3.35 mm. The pressures applied were in the range between 30 and 180 MPa. The results showed that the specific energy consumption increases linearly with the pressure; the product fineness increases also with the pressure, but the magnitude of this increase declines as the pressure goes up. Under the same stressing intensity, the product size distribution curve becomes steeper as the particle size decreases, so there is no self-similarity between product size distributions of different feed sizes. The suitability of a material-characterization model for interparticle breakage was verified for this ore. In addition, the effect of interparticle breakage on comminution of this ore with respect to its influence on the downstream flotation were analyzed in terms of size-metal distribution and mineral liberation.

Jan 1, 2016

By W. R. McQuarry, M. E. Wilson

"The structural relations of the ore deposits of the Staclacona mine are of considerable interest, for they not only illustrate the effect of a change in competence of the wall-rock, but also the effect of either the convergence together of two faults, or a change in the clip of a fault, or both of these factors, on ore deposition.The mine is in claim M.L. 1818 near the eastern end of Pelletier lake and lies about 2 miles south of the town of Rouyn. The Company was organized in 1926 to explore claims in Rouyn, Dufresnoy, and Beauchastel townships, but attention was directed mainly to those in Rouyn. Underground work began in 1928 with the sinking of the main shaft to a depth of 300 feet. Except for 1930 and 1931, the mine has been in operation continuously since that time. Production, which began in 1936, up to the end of 1946 has amounted to 1,381,422 tons of ore from which gold and silver having a total value of $7,861,860 were recovered. The average grade of the ore milled in 1946 was $6.68.GEOLOGYThe rocks in which the Stadacona ore deposits occur are mainly volcanics of the (Keewatin) Abitibi series intruded here and there by numerous dykes, sills, or masses of diorite. Single dykes of olivine diabase and lamprophyre are also present in the property and are intersected in the mine workings. The volcanic rocks are part of a wide belt of northward dipping lavas and pyroclastic rocks, having a thickness of over 16,000 feet, that extend from the east-west trending belt of Timiskaming sediments on the south northward to the Horne Creek fault and form the south limb of a large syncline. The volcanic rocks within the property consist of numerous, east-west trending, northward dipping flows of andesite and a few flows of rhyolite interbedded with rhyolite ruff and agglomerate. The angle of dip throughout most of the property is 60° to 80°N., but in the main cross-cut on the 850- and 975-foot levels stratification in rhyolite tuff was noted dipping 35°N. The tuff at this point lies above an intrusive mass of diorite and it is probable that the change in dip results from the way in which the tuff and agglomerate have been thrust aside by the intrusive."

Jan 1, 1954

By R. Augsten, K. K. Feng, K. C. Cheng

"Methane emission and the desorption characteristics of vertical borehole coal samples of Greenhills multiple seams in the vicinity of Elkford, British Columbia were investigated. Three vertical boreholes at depths of 335 m, 380 m and 395 m were drilled along the west wall of an active open pit mine and 44 core samples from various coal seams were obtained for desorption studies.The results are presented in three tables and illustrated with six figures. The methane content was found to increase significantly at depths greater than 200 m. The adsorption equation by Kim and the properties of the coal have been used to predict the methane content and these were compared with the measured values by the direct method.IntroductionThe coalification of plant material in the sedimentary rock produces different ranks of co al and gases of various composition. The gas mixtures are retained in coal beds and rock strata under pressure. The gas content in a coal bed varies considerably depending on the rank of coal and the depth of overburden. The gas content is defined as the volume of gases adsorbed in a unit weight of coal materials. The net amount of gases remaining in a coal seam depends on the difference in the rate of generation of methane by geo-thermal heat and the rate of diffusion of the gases out of the coal bed through sedimentary cover. The major factor that causes the change in rank and the liberation of gases is the temperature, which is governed by the thermal conductivity of sedimentary cover and the heat flux through the underlying rocks. The rate of diffusion of the gases out of the coal is governed by the porosity of the overlying rocks and the degree of fracture. The measured values of gas content in major North American coal beds are from zero up to 24 cm3 per gram of coal(1,2). A gas content of 2.5 to 9 cm3/g is considered ""gassy"" and that of 9 cm3/g or higher is considered ""very gassy"" for underground mining(3). Normally, the gas mixtures released from bituminous coal in Canada contain 90 to 98% methane and the remainder is made up of CO2, N2, 02, H2, He and other hydrocarbons(4)."

Jan 1, 1984

By J. E. Hawley

"The property of Francoeur Gold Mines, Limited, lies directly west of the Armfield mine in Beauchastel township, Abitibi district, and 12 miles west and slightly south of Noranda. The gold deposits are of particular interest because of their replacement character and close association with fault zones. The property was originally staked in 1923 following the discovery oi a mineralized zone near the eastern boundary. This became No. 1 orebody. Later discoveries in 1936 of No. 2 and No. 3 orebodies led to underground development and actual mining in July, 1938. A fourth orebody, No. 8, was found in 1939.The following is the production record up to December 31st, 1947:Beginning in September, 1944, ore was shipped to Noranda as siliceous flux, but late in 1946 milling of low-silica ore from No. 1 orebody was undertaken until operations were temporarily suspended in 1947.The four main ore deposits, Nos. 1, 2, 3, and 8, consist of siliceous ferrocarbonate and albite replacement bodies mineralized with fine pyrite and specularite in schistose fault zones in Keewatin volcanics. Barren to low grade quartz veins though present in some are uncommon, but small stringers of quartz are usually present wherever here and there visible gold is found. Nos. 1, 2, and 3 deposits lie in a major fault zone that extends completely across the property from west to east (over 7,000 feet) and dips N.40° to 50°, and are separated by intervals of 1,800 to 2,000 feet respectively. The fourth lies in a smaller fault zone striking east and dipping on the average 65°S.No. 1 orebody has been explored by mining to a depth of 500 feet, No. 2 to 400 feet, and No. 3 to slightly less than 300 feet . The greater part of No. 8 lies above a depth of 200 feet, but a raise has recently .been driven through from the west end of the 5th level of No. 1 to the 2nd level on No. 8 zone. Most of the ore of No. 8 zone above the 2nd level and of Nos. 2 and 3 above the 3rd levels has been removed."

Jan 1, 1954