Search Documents

By H. T. John

"The objective of this paper is to demonstrate how the optimum cut -off grade can be calculated for typical large tonnage openpit mines. In the examples, it is assumed that the concentrator tonnage is fixed and that there are no market restrictions. The mining rate is assumed to be variable. This is usually the situation at an operating property.ModellingA model of the ore body is required to examine alternate cutoff grade strategies. The model must be accurate in its relationship between grade and tonnage. Table I shows a typical relationship between ore tons and grade for various cut-off grades. The average strip ratio is also shown. For higher cutoff grades, the ore tonnage is decreased and the ore grade is increased. Strip ratio increases with the cut-off grade.Using the relationship between ton s and grade, and assuming a homogenous, long life orebody, a simple calculation of the optimum cut-o ff grade can be made. The objective is to maximize the present value of cash flows. For the long life homogenous orebody example this objective is satisfied by maximizing present cash flows.Cash flow is calculated by subtracting operating cost from revenue . Operating cost will increase with the cut -off grade as the strip ratio increases."

Jan 1, 1985

By Xiao Huang, Jean-Francois Thibault, Ali Merati, Prakash C. Patnaik

Single-crystal nickel-based superalloys are the current state-of-the-art technology for the manufacture of turbine blades. This technological improvement of the turbine blade has brought a considerable increase in its cost. Repair and overhaul of service stressed single crystal turbine components is an economic necessity for life cycle cost reduction of engines since the cost associated with replacement is significantly higher than its counterpart polycrystalline component. This paper will first review the recently reported research in developing repair technologies used for DS and SX components. These techniques repair the crack or defect while at the same time ensuring that the mechanical properties do not deteriorate and, more importantly, that the single-crystal microstructure is not jeopardized. It will then be followed by a brief overview of the research conducted and initiated by the authors with regards to the repair of single crystal alloys.

Jan 1, 2004

Advanced high temperature electrochemical systems such as fuel cells, electrolyzers and ionic transport membranes are currently being developed for a wide variety of energy conversion, storage and gas cleanup applications. These systems offer high electrical efficiency, multi fuel capability, modular construction, no/negligible emissions (SOx, NOx, VOC, particulate matters) with capability to sequester green house gas emissions (GHG). Electrochemical processes and electrode reactions will be discussed. Cell and stack component materials and fabrication processes will be presented. Bulk, surface and interface degradation processes responsible for cell and stack performance degradation will be examined.

Jan 1, 2005

By O. Moselhi

This paper describes a method for selection of most suitable project delivery systems for capital projects. It expands upon the method advanced by the Construction Industry Institute (CII) in 2003, and incorporates additional decision criteria and project delivery systems in a multi-tier decision computational platform. The paper integrates the analytical hierarchy process to alleviate the inherent subjectivity associated with the assignments of relative weights to selection criteria used in the CII method. It also expands the range of project delivery options to include Public Private Partnership (PPP) and Integrated Project Delivery (IDP). The range of selection criteria was expanded by 60, beyond the 20 criteria of the CII method. Relative effectiveness values are proposed for the added project delivery systems making use of recent project cases in Canada and the USA. The method was implemented in a spreadsheet application. Multiple scenarios were considered for one of the cases presented in the CII study and a sensitivity analysis performed based on the developments made in this paper. The differences in outputs between the CII method and the proposed method are discussed. This is the first decision framework that incorporates both the presently used PPP and the recently introduced IDP, along with the widely used project delivery systems. The developed method allows users to filter out the factors and alternatives that do not apply to the case at hand, based on key inputs at the upper tier. The method is flexible and can easily be expanded upon and customized by the user.

Aug 1, 2013

By K. Morikawa, K. Asano, J. Yoshitomi

The quality requirements for ladle shrouds have become stricter year by year to the pursuit of higher productivity and improved quality in the continuous casting of steel. The ladle shrouds must be sufficiently durable under severe conditions, such as operation without preheating and during several sequential castings. The consideration is that ceramic fibres, which have been applied in shrouds for thermal insulation during casting, could pose a risk to the worker's health. We realized materials for the ladle shrouds which show high strength and low elasticity. At the same time pursuing effective insulation, a coating which contains no fibres (Foaming Coat) has been developed, replacing the conventional one containing fibres. These materials are durable under conditions of repetitive use and consequently satisfy the customer's demands. The ladle shrouds which were improved in this way have achieved an excellent durable life in hot service of three times that of conventional ones. This paper reports the recent technological developments in ladle shrouds as well as their performance under hot operating conditions.

Jan 1, 2004

By M. Nowak

Extreme high grades often exert too much influence on surrounding block estimates, leading to a smearing of high grades that can cause overestimation of mineral resources. This concern underlies the decision to cap high grades, i.e., to lower the highest grades in a drill hole data set to some level deemed to be reasonable for producing reliable resource estimates. The choice of a capping level can, by itself, have a large influence on the analysis of the economic viability of a project. Despite this, it is often a choice that is made arbitrarily, guided more by art and tradition than by sound technical analysis. This paper makes suggestions for good capping practices, using methods and procedures that have been presented elsewhere, in the technical literature and in conference papers. The authors propose to use capping only if absolutely necessary, and review examples of cases where capping may not be necessary, or where capping does not make the estimates more reliable. It addresses two particular instances where capping is recommended: (1) where there is good reason to believe that estimation with uncapped grades will overstate the true underlying average grade, and (2) where there is potential for overly optimistic assessments of local block grades in the vicinity of some very high grade assays. The proposed capping practice is based on adjustments to only a very few high grade assays. The level of this capping can be assessed by bootstrapping and through analysis of the effect of extreme values on summary statistics like the average and the coefficient of variation. The paper recommends that good practice include an examination of the potential for local overestimation in higher grade areas.

Aug 1, 2013

By R. Alarcón Sch., R. Abel F.

For many years, copper cathode quality has been a priority for end consumers, since it affects the variety of products that can be obtained from them. From the beginning, physical and chemical quality of the wire bars was controlled, as this product was used to obtain wire rod and other forms of copper by wire drawing. At that time, all the electro refined cathodes were melted and casted as wire bars. Subsequently, in the 80’s, with the introduction of continuous casting furnaces, it was possible to directly produce wire rod from cathodes. From then on, cathodes quality standards were consistently increased, by the introduction of uniform criteria, among which we can identify ASTM and British Standards as well. Also, producers began to use more demanding internal standards than the existing specifications, in order to differentiate their cathodes as high quality products among customers. Today the physical aspect of cathodes, including nodules, cracks, sulfates, or others, is the first element used by end customers to assess their quality. This paper aims to show a brief vision of the evolution of quality specifications for products used to manufacture copper wire. INTRODUCTION From the beginning of refined copper production for industrial purposes, mandatory minimum quality conditions were established. These quality conditions were used as the main element to determine prices and discounts of the respective sales contracts. Reviewing the copper development history, we can appreciate that its quality requirements had been constantly evolved, so that currently refined copper has an extremely high quality standard, that allows its direct use in the production of ultra-thin cables and other products applied in the industry. In each stage, refined copper production has fostered the development of technology used in their treatment. Similarly, cathode processing technology has been evolving to minimize treatment costs in order to generate a wire rod for several uses, ranging from power cables to super conductors. In this sense, to the already known type of fusion processes of the Southwire or Asarco type (capacities over 80 kt / year), wire rod production processes of the Upcast or Rautomead type (capacities between 20-50k t / year) have been added. They immediately deliver oxygen-free wire rods. In both cases, we can conclude that the clients' requirement had evolved from a chemical criteria focus, to considering more subjective aspects, such as visual control as the first stage of inspection.

Jan 1, 2019

By Roger M. Nendick

"IntroductionThe stages of development for bringing a mill into production demand that a flowsheet for the process be developed at an early stage. Detailed engineering of the mill may then proceed without duplication of engineering effort on alternative processes. In the case of gold and silver mills, several process alternatives exist which must be evaluated before the flowsheet is finally fixed. The recently developed Carbon-in-Pulp process has added to this choice.Clearly, the major factor in determining the most suitable process is the amenability of the particular ore to a given treatment. Other factors that will also influence the choice are location, climate, power and water supplies, and available capital.Gold and silver milling processes can be divided into three main types:Gravity Concentration;Flotation;Cyanidation.Combinations of the three are frequently used; i.e. flotation followed by cyanidation of the concentrate, or gravity concentration in the grinding circuit with cyanidation of the classifier overflow. The following are the salient advantages and disadvantages of the three main alternatives.Gravity ConcentrationGravity concentration is suitable for free-milling gold ores, i.e. ores in which the gold is relatively coarse and free from sulphides. It should be noted that just because an ore is high grade, it is not necessarily free milling.Gravity concentration methods include jigs, shaking tables, spirals and more recently Reichert cone concentrators. All methods exploit the density difference between gold, which has a specific gravity greater than 15, depending on how it is alloyed, and the gangue, which usually has a specific gravity range of 2.7 to 3.5.A concentrate grade of several hundred ounces per ton might be produced, but recoveries by gravity alone are generally low in comparison to other methods. For this reason, gravity circuits are usually used in combination with flotation or cyanidation circuits."

Jan 1, 1983

By T. Navessin

Recent research activities in proton exchange membrane fuel cell (PEMFC) have significantly improved the performance per unit cost and its lifetime. These activities narrow the technology gaps, and thus, enable commercialization in some applications. One particular focus is in the development and understanding of proton conducting membrane materials. Many novel membranes are being developed which provide control and systematic understanding of complex relationships between chemical structure, morphology, physicochemical properties, and electrochemical kinetics. In this study, different classes of proton conducting membranes suitable for portable and automotive applications were evaluated in an operating PEMFC at the Institute for Fuel Cell Innovation, National Research Council. Analysis of these results may provide constructive feedbacks to the material researchers.

Jan 1, 2005

By Roy EI. Durr, Glen R. Davidge

"This paper presents the results of structural analyses and full-scale destructive tests conducted on liner plate culverts. The purpose of this work was to establish a design method and evaluate the suitability of using these structures in potential roof-fall areas for a rehabilitation application in lower stress and relaxed mining environments. Field evaluation of the design is currently in progress.Theoretical ultimate resistance functions were established for two different culvert shapes and were found to be representative of their experimental behaviour. The ultimate resistance function was used to determine their plastic behaviour to a rapidly increasing deflection condition, to determine the energy absorption capacity of these structures, and to predict their response to impact loading.IntroductionThe Kidd Creek mine of Falconbridge Limited is located justnorth of Timmins, Ontario. The area under rehabilitation for which this program was developed is the 2600 level of the No. I mine. The problem of effectively securing selected drifts at the 2600 level in NO.1 mine, for access to a high-grade ore block, is key to the economics of the operation. Diamond drill test holes had indicated a loosened rock mass above the 2600 level of about 7.5 m thick in response to the extensive mining operation below this level. This level forms the arbitrary boundary between the No. I and No. 2 mines, and has extensive volumes of cemented rock fill below it and largely untouched ore above it to the 2000 level in the North orebody. The walls at that level were showing relaxed ground conditions typical of de-stress: sub-horizontal joints opening up, and peeling.Due to the ground conditions, the consequent safety risks, the high grade of the ore, the potential production delays, and the likelihood of several phases of rehabilitation, regularly used drift rehabilitation employing rock bolts, cable bolting, or shotcrete was not practical. Two options were deemed possible alternatives to suit these conditions, steel sets with blocking and lagging, and liner plate culverts with backfill. Culverts were chosen."

Jan 1, 1995

By K. Enns, J. J. Byerley

"While thiocyanate (SCN-) is used in a number of industrial processes (production of polyacrylonitrile filaments, synthesis of agricultural chemicals and certain metallurgical solvent extraction and flotation circuits) it is recognized more as an undesirable by-product associated with ' the metallurgical industry. Thiocyanate is present at low concentrations in some waste streams from the iron and steel industry. Of particular significance is the formation of thiocyanate during cyanidation of gold and silver ores, concentrates, tailing s and residues. The thiocyanate levels present in the resulting effluents may range from a few mg/I to several thousand mg/I.At present, thiocyanate does not appear to be as hazardous in the environment as cyanide (CN-) at the same concentration although its interaction with other species and resulting decomposition of products may be unacceptable. Of course the presence of thiocyanate in the leaching circuit and ultimately in the effluent streams may add considerably to the oxidative requirments of any non-selective treatment process for cyanidation wastes.With respect to the thiocyanate as it relates to the cyanidation process, two aspects are evident. Thiocyanate forms and persists in the cyanidation circuit resulting in a ""fouling"" condition with subsequent loss of leaching activity. In order to reduce or control this problem, it is common practice for some mills to discharge daily as much as 20% of the barren leach liquor. Besides contributing to fouling of the leach liquor the formation of thiocyanate represents an irreversible loss of reagent cyanide. It is noteworthy that in some present or proposed mill practice reagent cyanide loss through thiocyanate formation may reach 50%(1). The purpose of this paper is to discus s the application of controlled electrooxidation of thiocyanate with the view of suggesting a process for regenerating cyanide from waste thiocyanate(2). The paper describes the important theoretical aspects and presents experimental data obtained for thiocyanate electrooxidation using both small and large scale electrochemical reactors. Some economic conclusions are presented."

Jan 1, 1984

By Lee Barbour

Waste-rock piles from metal mining operations are comprised of large surface deposits of unsaturated, coarse-grained soil and rock. The unsaturated condition and heterogeneous, coarsegrained nature of these deposits make them difficult to monitor or characterize. Key parameters that must be evaluated include; volume-mass relationships (e.g. water content, air content, porosity, density, degree of saturation, grain-size), transport properties (e.g. air-permeability, gas diffusion, hydraulic conductivity), geochemistry (e.g. solids, gas, and fluid phases) and soilatmospheric fluxes (water and gas). This paper describes some of the techniques that have been developed to characterize waste rock piles for uranium mines in Northern Saskatchewan. For each technique, the method of measurement is described, and preliminary field data are presented and discussed.

Nov 1, 2002

By John G. Henning

Low quality rock is encountered in many manifestations in underground hard rock mines, ranging from weak and poorly consolidated rock to highly altered or foliated rock. Lateral mine developments driven in low quality rock pose on-going challenges to a mine operator, as ground stability issues, such as caving of under-supported ground, drift closure due to surface deformation or buckling processes, and degradation of exposed rock surfaces are a persistent concern. For many operators, ground support design is an iterative process, as support practices are refined with time. Using case studies from a variety of underground hard rock mines, this paper reviews techniques for the classification of low range rockmasses and examines the rationale and effectiveness of adopted ground support systems.

Oct 1, 2010

By M. R. P. Snow

"This paper outlines geotechnical conditions that commonly exist in underground, hardrock mines and the challenges posed for ground-support steel, specifically rockbolts, used in these environments. A model is proposed whereby the in-situ stress and rock-mass classifications (based on Bieniawski’s rock mass rating) form the basis of determining the desired steel properties of the rockbolts used. Based on the ASTM F432 bolting specification, recommended minimum steel properties are defined for three ranges of in-situ stress levels, each with their own six ranges of RMR values. Heat treatment for the steel can be specified once these minimum steel properties are known.RÉSUMÉ Le présent article décrit les conditions géotechniques qui existent fréquemment dans les mines souterraines de roches dures et les défis que cela pose pour le soutien de terrain en acier, plus spécifiquement les boulons d’ancrage utilisés dans ces environnements. Un modèle est proposé dans lequel les contraintes in situ et les classifications de la masse rocheuse (selon la classification de la masse rocheuse de Bieniawski) servent de base pour la détermination des propriétés désirées pour l’acier des boulons d’ancrage utilisés. En se basant sur les spécifications de boulonnage de l’ASTM F432, les propriétés minimales recommandées pour l’acier sont définies pour trois plages de niveaux de contraintes in situ, chacune avec sa propre plage de six valeurs de classification de la masse rocheuse (RMR). Un traitement thermique pour l’acier peut être spécifié une fois que ces propriétés minimales pour l’acier sont connues."

Jan 1, 2016

By E. Ferguson

In evaluating refractory designs for cast house applications, thermal calculations are frequently performed to determine cold face shell temperatures, temperature profiles and metal freeze plane locations within the refractory layer, and heat loss in the steady state condition. A problem arises when looking at molten metal transport crucible designs in that these structures are usually operating under non-steady state conditions throughout their production cycle. Because the molten metal temperature varies with time, and material properties such as thermal conductivity are temperature dependant, mathematical solutions are at best... complicated. This paper presents a relatively simple, iterative solution, that can be set up on a standard computer spreadsheet program, to calculate heat transfer in non-steady state conditions. These calculations can provide curves for (1) molten metal temperature vs time and (2) cumulative heat loss vs time, given variable starting conditions, to aid in the evaluation of molten metal transfer crucible refractory designs.

Jan 1, 2004

By F. Schulz

NA's primary smelter has continually increased its production output in the past decade, making it necessary to improve the lifetime of the casting moulds for copper anodes. The current throughput of more than 1,100,000 tonnes per year of copper concentrates amounts to an output of about 450,000 tonnes per year of anode copper at NA's Hamburg plant. The anodes are cast on a single casting wheel with 24 anode moulds. Besides the stable chemical analyses, the reproducible geometry of the anodes is an important precondition for the success of the subsequent electro-refining process. The anode moulds are subjected to thermally-induced alternating stress and side reactions with the melt. Typical signs of wear will be shown and discussed. Different processes to produce anode moulds will be introduced and the results in terms of their lifetime and the quality of the anodes themselves will be discussed. Finally an outlook is given on possible efficiency improvements.

Jan 1, 2007

By A. Suzue, T. H. Okabe, Y. Taninouchi

Methods for the physical separation and enrichment of platinum group metals (PGMs) from autocatalyst scrap were studied in order to develop an environmentally friendly and efficient recycling process. In general, an autocatalyst has a honeycomb-structured ceramic substrate that is coated with a catalyst layer containing platinum (Pt), palladium (Pd), and rhodium (Rh). Therefore, physical separation of the PGM-containing catalyst layer directly from the ceramic substrate is favorable for upgrading the autocatalyst scrap. In this paper, the authors present a scrap-upgrade process consisting of electroless iron plating and magnetic separation techniques. Iron was plated on the surface of a catalyst sample used to represent an autocatalyst, which was then crushed and magnetically separated. The Pd in the catalyst sample was successfully extracted and concentrated in the magnetic powder. Under certain conditions, the process increased the Pd concentration by a factor of 4 and recovered 89% of the Pd in the autocatalyst sample.

Jan 1, 2014

By Marc Bétournay

This article examines how fuel cell technology and related power distribution system fits within mine operating requirements. Considerations for improvement of power plant architecture and functions to yield production advantages are presented. Improvements to conventional mining approaches are also discussed.

May 1, 2007

By C. R. Edwards, D. R. G. Watt

"Equity Silver Mines Ltd. a member of the Placer Development group of companies operates Canada's largest silver mine near Houston in north-central British Columbia. Initially, the silver-gold-copper flotation concentrate contained excessive levels of antimony and arsenic, so a leach process was installed to remove undesirable metals and provide improved smelter terms for the leached concentrate. The leach plant which has been fully described elsewhere (1, 2, 3), was forced by deteriorating process economics to shut down in April 1984. Equipment was mothballed and alternate uses sought.The Endako Mines Division of Placer Development Limited, located some 150 kilometres east of the Equity mine site, shut down its molybdenite mining and milling facilities in the spring of 1982. Endako has continued to produce molybdic oxide (molybdenum trioxide or MTO) via intermittent roaster runs, and also a high purity, lubricant grade molybdenum disulfide in the Ultrapure Plant. With the steel industry in the doldrums, molybdenum chemicals present an alternate and growing potential for molybdenum sales. In 1982 Placer Development began testing this market. Molybdenum chemicals were produced in the United States on a toll basis using Endako MTO as process feed. The transfer of this production to Canada was being considered when Equity's leach plant shut down, and it was noted that most of the equipment and skills necessary could be provided by the leach plant. See Figure 1.A careful investigation of process requirements was completed by engineering and production staff at Equity and Endako. A provisional capital and operating cost estimate was made, and it was decided to perform a test run during July 1984. There were strong reasons to proceed with this project. A positive cash flow was expected for both Endako and Equity. Endako would have product to continue to expand in the molybdenum chemicals market with the added selling point that now the complete production process would be under direct control of Placer Development companies. Equity would further benefit since a portion of the leach plant would continue in operation thus maintaining and exercising our hydrometallurgical engineering and operating skills. Finally, Equity would have a base from which to search out other processes adaptable to the idled leach plant equipment."

Jan 1, 1986

By F. Urekar, R. B. Pankhurst

"Air spaces and air gaps in an explosives column are known to allow greater distribution and cushioning of explosive energy from the rock mass. This energy distribution is enhanced if the explosives ' gases can be confined in the borehole for as long as possible by plugging and stemming above the air space.Power Plug is an inflatable plug which can seal a borehole at any point to separate the stemming from an air gap and explosive toe load.IntroductionThis paper will discussion-going work by C-I -L Inc. and operators of two open pit mines to study the results of using Power Plugs:I. Pit wall stability - the authors have found the Power Plug effective for wall control blasting in open pit mines.2. Selective mining of coal seams - the authors work shows the Power Plug allows mining selective coal seams by predrilling underseam waste wedges.Pit Wall StabilityWall stability in an open pit mine is essential for safety. Good wall stability can be achieved with wall control blasting techniques which cushion the effect s of the explosives charge by decoupling the charges from the borehole wall. The usual method of decoupling a charge in a large-diameter rotary borehole is to load the explosives in tubes (Fig .I) . We now believe the air deck system is effective in sea ling a borehole above the explosive charge to create an air deck within the borehole which will cushion the blast.In a linear decoupled charge, an air annulus surrounds the explosives charge and cushions the effects of detonation genera ted gases on the pit wall. In an air deck, i.e. with the hole plugged at the collar, the gases genera ted by an explosive toe load are sealed in the empty borehole column. After a period of time, these trapped gases produce radial cracking between holes along the entire length of the borehole.It is common practice to employ de coupled explosive charge columns in the borehole to limit blast damage to surrounding rock. The exact mechanism of energy transfer in such blasts, however, is not well understood. Interruption of the continuous explosive column in a borehole by means of stemming, or air decks, may also be viewed as another form of decoupled blast. Decoupling of the explosive charge from the borehole wall affects both explosive energy release and explosion pressure developed in the borehole."

Jan 1, 1988