Search Documents

"Decreasing gold-in-ore grades is one of the main drivers of poorer productivity and rapidly escalating unit costs. Grinding costs, water use and reagent consumption are all intimately related to the ore grade processed. Various pre-concentration technologies have been developed that can be applied at various stages of crushing prior to ore grinding. This paper will review the amenability of ores to coarse particle barren gangue rejection for fine crush sizes in the pumpable particle size range (i.e., particles between 5 mm and 0.3 mm in size). The liberation of oxide gangue achieved during crushing is evaluated by proxy using sink-float analysis and the deportments of gold, sulfur, and arsenic into sinks and floats are monitored. Amenability of gangue rejection by continuous gravity separation is evaluated after various crushing modes (vertical shaft impact crushing, cone crushing, and HPGR crushing). The potential to identify coarse particle mineral association and liberation using three-dimensional x-ray computed tomography will be discussed.INTRODUCTIONThe aim of research in this area is to explore some of the attributes which make some ores amenable to preconcentration, or rejection of a significant component of the feed mass to tailings at a coarse liberation size. Characteristics such as ore type, mineralogy, breakage pattern, particle shape, and liberation characteristics may need to be examined to identify amenability to pre-concentration amenability.It is intended to focus on continuous gangue rejection in the pumpable size range (0.3–5.0 mm) as this remains one of the key opportunities to reduce processing costs through a combination of techniques including screening (for mineral differentiation rather than size classification only) and gravity separation (using jigs). This is to be contrasted to conventional preconcentration as performed with automatic ore sorters."

Jan 1, 2016

By Takanori Kokubo, Kenta Suzuki, Tomohiro Sasaki, Toshiya Anami

"Previous work has shown that the strengthening Al-Mn alloys with copper leads to the formation of an undesirable reduction in recrystallized grain size. In this study the mechanisms of strengthening and recrystallization behavior in a continuously cast automotive heat exchanger fin stockof Al-1.1wt%Mn-0.5wt%Fe-0.3wt%Si with a0.3wt%Cu addition were investigated. Metallurgical analysis revealed that the Cu strengthening was dominated by the formation of dispersoid particles, while solid solution strengthening decreased with the Cu additions. This result is attributed to the decrease in the amount of Mn solid solution. The post brazing recrystallized grain size was reduced compared to that not containing Cu. It is postulated that the Cu addition leads to a decrease in the amount of Mn in solid solution which leads to a finer grain size. This effect is attributed to Mn in the aluminum matrix inhibiting boundary migration but allowing other grains to grow during heat treatment. The results are rationalized based on particle stimulated nucleation (PSN), wherein dispersoid particles are more likely to become active recrystallization nuclei during the heat treatment. The increase in the number of active dispersoid particles with Cu addition is correlated to the recrystallized grain structure.INTRODUCTIONImprovements in properties such as strength, braze ability and corrosion resistance in thermal fin stock alloys are all means to gain improved efficiency in heat exchangers particularly in automotive applications. While Al-Mn alloys dominate automotive heat exchanger fin stock alloy, even small chemical compositional changes can profoundly influence these properties (Kawaharaet al., 2004; Yoshino et al., 2009). The microstructure (particularly the grain size and shape) also plays a key role in determining the product performance and hence the thermo-mechanical processing (TMP) must also be considered. The casting method (typically conventional direct chill, DC, or continuous casting) significantly influences the properties in no small part due to the very different TMP routes that are used. Continuous casting is generally favored for fin stock applications as its higher cooling rate (which can be 2 to 3 orders of magnitude higher than DC casting) leads to finer as-solidified intermetallic particles and an increase in super-saturated solid solution elements (such as Mn)that are known to improve fin stock performance such as strength, braze ability(Okiet al., 2008)."

Jan 1, 2018

By J. P. Harrison, R. Roostaei

"In this paper we investigate the consequences of using conventional triaxial peak strength criteria in the polyaxial stress conditions that occur around the end of a long circular underground opening. A series of 3d boundary element analyses were performed using Examine3D to determine the stresses induced around the tunnel in different in-situ stress conditions. To discuss the applicability of a triaxial strength criterion in failure prediction, strength factors were computed for both the Ottosen polyaxial strength criterion and the triaxial Hoek-Brown criterion. Assuming that the Ottosen criterion is an accurate indicator of strength factor, the discrepancy from this value due to the Hoek-Brown criterion is the error in prediction.In order to simultaneously show the error in prediction and actual strength factor, a quantitative bivariate colour scheme is used to visualize the results. This allows rapid identification of regions with large error, and where either unsafe or overly conservative conditions occur. We show how the inappropriate use of triaxial criteria rather than polyaxial criteria leads to an under- or over-estimation of strength factor, and can result in uneconomic or unsafe design. Extending the analysis to different in situ stress regimes shows how the in situ stress conditions affect the assessment."

Jan 1, 2015

By J. E. Nelson

This paper will examine the problems inherent in matching grinding mills with electric motors through connecting elements such as clutches. Emphasis will be on the uncertainties of mill torque and power demands and the need to recognize these if dependable, safe designs are to be obtained.

Jan 1, 1972

By S. S. Al-Thyabat, A. M. Ghrair

"Printed circuit board (PCB) is the main part of any electric or electronic device, providing mechanical support and electric connection for the board eclectic components such as capacitors, resistors, diodes etc. PCB consists of non-conductive substrate overlaid with one or more layers of copper sheets. They also contain appreciable amounts of base metals (copper, nickel, tine, and aluminum) and precious metals (gold, silver, and rare earth elements (REE)) which end up in the landfill at the PCB end-of-life.PCB recycling E-waste in general is a profitable business; many valuable raw materials, precious and base metals, can be extracted with high purity. Approximately, one metric tonne of PCBs may contain 80-1500 g of gold and 160–210 kg of copper. The precious metals recovered from PCBs occur at concentrations higher than commercially mined minerals. Also PCB recycling is very important to our environment since many heavy metals (e.g. lead) may be leached from the landfills to the underground reservoirs. In Jordan, however, the work conducted on E-waste and PCB recycling in particular is limited; currently most of the E-waste is either exported or dumped in the landfill.In this work, a combination of physical (magnetic separation), physicochemical (flotation), and chemical methods (leaching) were used to compare metals concentrations in leach liquors produced from a concentrates resulted from a combination of these methods. It was found the leach liquor of the magnetic fraction of the PCB coarse size gave the highest concentration of Fe, Al, and Ni while concentration of Cu was higher in leach liquor of nonmagnetic sink fraction. On the other hand, metals concentration almost similar for both sink and float of the fine size fractions, indicating even distribution of metals concentrations in the fine size fractions."

Jan 1, 2016

By C. Ciriello

Six Sigma methodology, as applied within Xstrata (formerly Falconbridge and Noranda), involves a disciplined approach to managing projects, solving problems, improving performance, and leveraging information. The four (4) cornerstones of Six Sigma are the use of Philosophy (customer driven, desire to improve and discipline), Metrics (measurement systems), Methodology (scientific method and sequence of deliverables), and Tools (such as statistics, change management, and root cause analysis). This paper will outline the general steps of the Six Sigma methodology and demonstrate how each phase directly applies to a real plant metallurgical project aimed at reducing nickel losses of the rougher flotation circuit at Raglan. The main concepts of Six Sigma are described, along with the specific challenges, successes, and deliverables related to the project. It is also the authors' aim to demystify the basic Six Sigma principles.

Jan 1, 2007

By Y. M. Shneerson, I. V. Fomenko, M. A. Pleshkov, E. A. Ospanov, A. A. Shakhalov, S. S. Naboychenko

Low-grade copper concentrates (with copper content less than 20%) often contain impurities such as arsenic, zinc, lead, mercury, antimony and bismuth. The pyrometallurgical treatment of such concentrates is associated with several problems, which will ultimately affect the cost and the quality of copper cathodes as well as by-products. SRC Hydrometallurgy proposed a complex hydrometallurgical technology which allows the removal of impurities and the enrichment of low-grade copper concentrates to a quality which will be more suitable for pyrometallurgical processing. Laboratory batch tests and pilot plant results for the pressure leaching steps are shown in this paper. The key parameters of the leaching steps were determined and optimized. The quality of possible by-products were also determined. The developed flowsheet includes two pressure leaching steps: pressure oxidation (POX) and hydrothermal alteration (HTA). Both operations are carried out at 170°C with subsequent flotation of POX and HTA residues and recovery of copper, zinc and lead into separate concentrates for further processing. The development of the flowsheet was based on the Balkhash Zinc Plant (Balkhash, Kazakhstan), which had been non-operational since 2009. The developed flowsheet for processing of low-grade concentrates will utilize 80% of the existing equipment of the Balkhash Zinc Plant, thus leading to a significant reduction in required capital expenditure. INTRODUCTION As the age of copper mining operations advance, copper grades continue to diminish and impurity levels increase. Therefore, copper producers are forced to look for new innovative hydrometallurgical technologies which are able to handle low-grade raw materials and solve problems associated with impurities in an economically justifiable way. New technologies allow to extract valuable components selectively and to process low-grade concentrates which had previously been marked as non-technological and economically unviable. Hydrometallurgical technologies for processing of copper-containing materials can be divided into two main categories: chloride and sulfate (atmospheric, autoclave and bacterial) based technologies. Since the 1970s, many autoclave techniques for the processing of copper-containing materials have been developed and implemented (Naboichenko, 2002; Dreisinger, 2005; Habashi, 2009; Shneerson, 2011). The mineralogical composition of the ore (or concentrates), geographical location of the deposit, distance from industrial areas, availability of existing treatment facilities, availability of skilled labor, cost of electricity and cost of neutralization are some of the factors which are usually considered when the appropriate technology is selected (Halbe, 2002).

Jan 1, 2019

By J. Béland

"Three stages, each characterized by a particular sedimentation, magmatism, mineralization and deformation, are recognized in the geological history of Gaspe. The first stage led to the formation of the Taconian orogen, the second to that of the Acadian orogen and the third stage to the accumulation of a post-orogenic cover. The Taconian orogen includes volcanic and detrital rocks of Late Precambrian or Cambrian and Lower to Middle Ordovician ages in which ultrabasic intrusions have been emplaced. Folding is severe. Mineralization is of the Cr-Ni-Cu type, related to the igneous facies.The rocks constituting the Acadian orogen include two distinctive sequences corresponding to two successive sub-stages. The second substage began in Early Devonian time with the first pulses of the Acadian orogeny. The rocks of the first substage grade southward from a nearly platformal sequence to an assemblage implying less stability and spotty volcanism. The second substage was one of synorogenic deposition of elastic rocks, first in a marine environment and later under terrestrial conditions. Granitic intrusions, surrounded by aureoles of skarn and hornfels in which Cu-Pb-Zn mineralization is found, accompanied the Acadian deformation. The second-stage"

Jan 1, 1969

By J. Fixter, P. Prangnell, Z. Pinter, E. Eimer, B. Chehab

"High deposition rate Wire and Arc Additive Manufacture (WAAM) can provide benefits to the aerospace industry, including a reduction in lead time, reduced material waste and, through higher solidification rates, refinement of the as-built microstructure relative to a cast material. However, candidate 2xxx series high strength alloys for this process normally require a solution treatment, which is problematic for large near-net-shape components, and age hardening to achieve maximum mechanical properties. With each layer being subject to multiple thermal cycles, exploiting the thermal conditions in the WAAM process to avoid post-build solution treatment is therefore of interest. A solutionisation model has been developed for the WAAM process, based on diffusion controlled dissolution using DICTRA, which was validated through thermal simulations combined with 2D and 3D image analysis. The model has subsequently been used to simulate the solutionisation behavior during a typical WAAM thermal cycle and to explore what could theoretically be achieved by, for example, refining the starting microstructure.INTRODUCTION There is currently great interest in exploiting additive manufacturing (AM) in the aerospace sector due to several benefits it can potentially provide; including reduced material waste, shorter product lead times and greater design freedom (Herzog, Seyda, Wycisk, & Emmelmann, 2016). However, with aluminium alloys the material properties obtained are generally inferior to those of conventional high-strength wrought products; therefore more research is required to explore the potential for exploiting the unique process conditions in AM to improve the as-deposited microstructure. A range of AM techniques are now available (Debroy et al., 2018), which differ in terms of the feedstock type and power source and it is necessary to match the appropriate technology to a particular application. This generally requires a compromise between the build rate and shape resolution. Wire and plasma-arc additive manufacturing involves using an electric arc to melt wire onto a substrate, and fabricates a part by building up overlapping layers of deposited weld beads (Addison et al., 2015; Williams et al., 2015). The benefits of this process over other AM methods are the much higher deposition rates (e.g. kg’s/hour) achievable and lower capital equipment costs relative to powder bed techniques, which makes it suitable for large scale applications. However, limitations include a lower part complexity, lower solidification rates and a greater need for post-process machining (Frazier, 2014)."

Jan 1, 2018

By Harry Wilton-Clark

Introduction Coal cleaning may be taken as meaning the separation of coal-as-mined into two or more fractions. Coal cleaning includes coal washing, together with any other means used in the ultimate preparation of coal prior to shipment (as coal) . The method of coal cleaning devised for any given mine must be one which is based entirely on the economic results obtainable. The installation of a high-cost and complex washing plant, designed to produce a low-ash dean coal, at the highest possible recovery, may be unsound practice. A crude 'roughing' washer may be the best result of sound engineering and operating consideration, and in some cases coal cleaning should be confined entirely to preparation at the face. Consideration of complete costs, to the point where the coal is actually sold, may show that certain seams are workable or not workable. Of the seams found workable, extraction of the whole or parts of the seam may be decided on. The portion to be extracted may contain rock or bone partings, which must be removed. It may be good practice to mine the extra portion and remove the objectionable materials by surface washing; or it may be that such materials should be removed underground, even at an increased mining cost. For instance, in some of the steeply pitching seams of the Alberta Crow's Nest Pass district, the removal of bone and rock at the face may be almost impossible under the usual 'up the pitch' or 'angle' mining methods, but possible by mining across the pitch so that the material to be rejected can be removed and gobbed. Again, if a complete seam is being extracted, investigation may show marked differences between top coal and bench coal, and if sufficient mine cars are being loaded from a chute at one time, the fact that such a place is working top or bench coal at the time may be reflected by peaks in ash content or size proportions at the ripple. It may be very effective coal preparation to smooth out such peaks.

Jan 1, 1934

By Osvaldo A. Bascur, Curt Heftier

The lack of integrated information including the Energy/Utility Suppliers with sufficient detail for analysis causes inefficient operation in metallurgical complexes including the Energy/Utility Suppliers . Defining the right context for information use is essential for sustainable operations. This being said, what are we doing to enable people to act upon information and to be aligned to optimize the use of resources like raw materials, energy, water and consumables for an entire metallurgical complex? Collaboration between all company entities is a key component of improving efficiency. Evolution of web technology and object modeling of enterprise assets enables collaboration across the whole business. Operational troubleshooting occurs more quickly as the organization acts on issues to reduce wasteful operation. This paper presents a real time software infrastructure with tools that give users the ability to sift through available data, transform data into information for business continuous improvement and optimization. We will introduce a new technology for analyzing real time data, information and events using multidimensional analysis of information to detect anomalies based on the statistics of the data classified by time events to reduce the information into action. A new paradigm for collaboration at a local and strategic level is proposed to enable the enterprise to become proactive in dealing with wasted time and products. Three examples from the industry will presented and their benefits highlighted.

Jan 1, 2011

By DALE MacGREGOR, VERA TUREK

lndusmin Limited acquired the St. Donat quartzite deposit in 1967 to produce high-quality silica for use in the sandblasting and silicon carbide industries. The quartzite, of Grenville age, is highly friable and porous. This is due to numerous small, kaolinite-coated cavities in the quartzite; the cavities were formed through leaching, probably by rising hot solutions.

Jan 1, 1984

By E. M. Córdoba

The effect of the Fe3+ lFe2+ redox couple on the chemical and biological dissolution of chalcopyrite was studied. All the tests were carried out in stirred flasks with 100 mL of a ferric/ferrous sulphate solution, in the absence or in the presence of bacteria (iron- or sulphur-oxidizing) and at low (35 DC) and high (68DC) temperature. The initial redox potential was controlled between 300 and 600 m V Ag/ AgCI and silver was used as chemical catalyst. The results showed that the oxidizing action of ferric ion on the chalcopyrite was controlled, in all cases, by nucleation and precipitation of jarosites on unreacted particles. The tendency of Fe3+lFe2+ solutions towards equilibrium favours the activities of both ions to be equal. Consequently, the dissolution rate was faster at relatively low redox potentials (between 400 and 500 mY) than at high values (600 mY). In this sense, the presence of ferrous ion in the system is a key factor to control hydrolysis and precipitation of ferric ion. Unlike jarosite, the elemental sulphur produced during dissolution of chalcopyrite was porous and did not act as a diffusion barrier.

Jan 1, 2007

By T. A. Chepushtanova, I. U. Motovilov, V. A. Luganov, G. D. Guseynova

"Kazakhstan has significant reserves of oxidized nickel ore with low nickel content. Processing of such ores is effective via pyrometallurgical technologies such as smelting to ferronickel or matte with consecutive extraction of metals from melting products. There are also many options for direct hydrometallurgical processing. However, they do not provide high nickel recovery.We studied extraction of nickel and cobalt by using combined technology of low-grade ore processing from the Shevchenko Kazakhstan deposit, which includes smelting to poor matte followed by hydrometallurgical processing of the matte. The nickel content in the initial ore was 0.75–0.9%. Pyrite concentrate of Sokolov-Sarybai Kazakhstan deposit containing 0.17% cobalt and 0.06% nickel had been used as a sulphidizer at smelting.As a result of the study, we were able to extract up to 98% of the nickel and up to 80% of the available cobalt. Obtained matte contained 3.1% nickel, 0.29% cobalt, 71.6% iron and 24.3% sulfur. Matte leaching was carried out by hydrochloric acid. The iron content in the pregnant solution was 170–185 g/dm3. Nickel and cobalt precipitation from the pregnant solution was carried out by hydrogen sulfide. Initial matte or cast iron was used as neutralizers during the process. Practically complete precipitation of nickel was achieved at 3–5% excess of neutralizer at 333–343°K in 4 hours; up to 95% of cobalt precipitation was achieved in 50% excess of neutralizer at 363°K in 8 hours. The purified solution contained 200–600 mg/dm3 of nickel, 80-100 mg/dm3of cobalt and 175–185 g/dm3 of iron. The purified solution allows to obtain iron oxides by high-temperature hydrolysis, and to regenerate hydrochloric acid.As a result of non-ferrous metals precipitation we obtained sulfide concentrate with concentration of Ni up to 25% and concentration of Co up to 5.5%. The technology is recommended for semi-industrial testing."

Jan 1, 2016

By L. Veleva, Garcia. A., G. Perez

Aluminum is a metal used for the transmission of electricity of high voltage, in the construction industry and other areas. In atmospheric conditions aluminum forms an oxide layer (Alz03'H20) as a result of its corrosion, entering the passive state. The oxide layer can be destroyed by the presence of ions (Cr, SOx-n) developing localized (non uniform) corrosion attack by pitting, difficult for evaluation. The concepts of fractals and self-similarity were used in this study for the characterization of the development of localized corrosion. Images obtained with a scanning electron microscope (SEM) of samples of electrolytic aluminum wire that have been exposed during one year in ruralurban and marine-coastal environments of the humid tropical climate of Mexico, have been processed. The development of pitting has been studied as a function of time, making a statistics of the frequency of appearance of pits versus the area occupied by them. The data show that the distribution of the pits follows a power law. Therefore, the concept of self-similarity can be applied for the study of the phenomenon of localized corrosion, describing their development with time.

Jan 1, 2006

This paper focuses on the dissolution of various Manganese based compact additions into liquid Magnesium. The experimental procedure employed cylindrical compacts with various Manganese compositions. The various temperatures of the additions and the Magnesium bath were measured simultaneously during the immersion of the additions into Magnesium bath. The exothermicity level of these additions during their dissolution into liquid Magnesium was determined. The relation of the exothermicity level with the dissolution kinetics was also examined. In addition, SEM and EDX work was conducted for additions, which were withdrawn from the Magnesium bath. Finally, the recovery of these additions was estimated by taking samples from the Magnesium bath and conducting ICP analyses.

Jan 1, 2006

By Isabel C. B Rodrigues, Flávia D. Reis, Versiane A. Leão, Rosa M. F. Lima

Attention has been focused in recent decades upon the precipitation of metal sulphides from acid mine drainage (AMD) and pregnant leach solutions, due to the advantages of the sulphide precipitation process over traditional methods employing hydroxides. The aim of this work was thus to explore technologies for copper precipitation using either Na2S or biogenic sulphide. The recovery of copper sulphide was improved when the initial pH of the solution containing each metal was 4 or excess sulphide was employed. In such, a condition the removal efficiency was 99.9%, corresponding to a residual level of 0.1mg/L for copper in solution. Kinetic parameters for precipitation were determined from the particle size distributions using the method of moments, where the growth and nucleation rates, as well the agglomeration kernel, were calculated. The biogenic sulphide was a suitable alternative to sodium sulphide for copper removal as either sodium sulphide and biogenic sulphide can be utilized to precipitate such a metal allowing the effluent to be compliant with environmental legislation.

Jan 1, 2014

By Vicken Aprahamian

"The Royal Canadian Mint (RCM) operates a gold and silver refining toll operation in Ottawa, Ontario, Canada. The silver refining line is a recent addition and was commissioned in 2005. One source of silver in the refinery is from gold doré which undergoes Miller chlorination before electrorefining to 99.99% cathode gold. Treatment of the Miller salt or silver-copper chloride produced consisted of a 2-stage high temperature reduction process step using soda ash prior to 2005. Copper-rich silver bars were produced and shipped offsite for further refining.The copper-rich bars could not be blended into sufficient high grade silver doré to dilute the copper and allow electrorefining in a silver nitrate medium. A new wet process was developed and commissioned to replace the high temperature reduction and allow removal of bulk copper. Thus upgraded impure silver produced was cast into anode for electrorefining to 99.9% purity silver flake. The 2005 RCM Hydromet Slag process is presented as well as its more current version. In addition, mention is made of a novel processing scenario for the introduction of Miller chlorination silver into the electrorefining circuit."

Jan 1, 2015

By X. -P. Zhang, L. N. Y. Wong

Shale gas exploitation initiated in North America has rapidly extended worldwide. Hydraulic fracturing is an emerging field technique for stimulating the gas reservoir. The study of cracking processes, particularly crack coalescence, is vital for a successful hydraulic fracturing to enhance the gas exploitation. Experimental studies have observed that the size effects of the constituent particles are significant on the cracking behavior of the rock specimens. To further investigate the size effects, the bonded-particle model (BPM), which is based on the discrete element method (DEM), is adopted in the present research. In flaw-containing specimens, by varying the crack resolution (?= a/2R), which is the ratio of half flaw length (a) to particle size (2R), the size effects on cracking behavior under compressive loading are studied. By keeping the flaw length constant, the particle size is varied independently in the BPM analysis. Decreasing the crack resolution increases the first crack initiation stress, but it has no obvious effects on the uniaxial compressive strength. The trajectories of the first cracks and secondary cracks hence generated have a higher resolution and are well-defined in those specimens possessing a higher crack resolution. On the contrary, in lower crack resolution specimens, the macroscopic first cracks appear to be wider and less continuous. These findings from numerical simulation clearly demonstrate particle size effects on cracking behavior. Special attention should be paid to these effects in future numerical study using the bonded particle model.

Jan 1, 2015

By C. Schmidt, M. Kohnk, C. Siemers, J. Kiese

The application of conventional titanium alloys is limited to 550°C due to their poor oxidation resistance. In addition, severe grain growth is observed in single-phase titanium alloys in long-term runs at elevated temperature leading to a degradation of their mechanical properties. In exhaust applications in automotive or aerospace engineering, products are often manufactured by cold-deformation like deep-drawing or rolling which is normally difficult in oxidation-resistant titanium alloys due to the presence of titanium-silicides. Therefore, in the current study, titanium alloys based on CP Titanium Grade 1S (soft grade) were developed showing (1) improved oxidation resistance due to a concerted addition of silicon, iron and niobium, (2) microstructure stability by the precipitation of hafnium-silicides mainly on the grain boundaries and (3) good cold-deformation properties. The industrial production route was developed so that the new class of Ti-Si-Fe-Nb-Hf-alloys is now ready for application in exhaust systems of planes or cars at minimum 800°C.

Jan 1, 2015