Search Documents

By Tiziana Apuani

The study refers to an area of about 70 km2, extended in the Italian Central Alps along the the San Giacomo Valley where different civil and mining works are present The regional geological setting is related to the Pennidic Nappe arrangement, characterized by the emplacement of sub-horizontal gneissic bodies resulting from the Mesoalpine isoclinalic folding of crystalline basements, emplaced throw East, and separated by matasedimentary cover units. The investigated geological rocks, belong to the ?Tambò?Unit, overlapped by its meta-sedimentary cover and by the ?Suretta? Unit. The tectonic contact gently dips to the E?NE. The valley, furrowed by the Liro Torrent, follows a N?S striking tectonic lineament, almost parallel to the nappe contact. A number of more then 70 sites, distributed in the studied area, were chosen and detailed structural and geomechanical field surveys were performed to characterize the rock masses, its intact rock and discontinuities. The procedure identifies the number of joint sets, their representative orientation, the set spacing, the type of movement, the amount of dilatation, the degree of alteration, the roughness coefficient, the presence and nature of infill. Rock mass quality indexes, such as the Rock Mass Rating (Bieniawski, 1989) or the Geological Strength Index (Hoek et al. 2002) have been evaluated in each surveyed site. The work is a contribute in assessing how the geometrical and geomechanical properties of the rock masses can be regarded as regionalized variables. The spatial distribution of these properties is a function of the geological and structural phenomena at which the rock masses have been subjected. The presented geostatistical analysis regards the spatial variation of the orientation of the most representative joint set.

May 1, 2009

By Carl Bertrand, Patrice Nadeau, Claude Bazin

"Rio Tinto Fer et Titane processes the ore extracted from the Lac Tio orebody to concentrate the hemo-ilmenite (FeO.TiO2-Fe2O3) mineral that is subsequently smelted to produce pig iron and titanium oxide slag. The ore is crushed, heat treated (roasted) and concentrated using dry magnetic separators. This paper describes a model to predict the magnetic susceptibility of the roasted ore and its behaviour in the magnetic separation plant. The model uses a classification of the ore as a function of the size and magnetic susceptibility of the particles. A subsequent division into mineral species allows the simulation of the magnetic separation process. The model is used to assess various operating options when process disturbances occur.INTRODUCTIONOre processing operations consist of ore size reduction followed by the recovery of valuable species in a concentrate that is subsequently sold for its minerals or metal content. The concentration processes are based on the physical and/or chemical properties of the minerals contained in the ore. Flotation is typically used to recover minerals of base metals such as copper, zinc, lead or nickel. Iron ore and other dense minerals are typically concentrated by gravity separation processes. Magnetic separation uses the magnetic properties of the minerals to concentrate magnetite and other minerals, to clean coal concentrate and to recycle ferrosilicon for dense separation processes (Brophy, 1985).Magnetic separators can be divided into low and high intensity separators and high gradient magnetic separators (Gillet, 2008). Most of the low gradient magnetic separators are built as rotary drums that are operated in wet or dry conditions. Dry magnetic drum separators are used by Rio Tinto Fer et Titane in Sorel-Tracy, Canada to concentrate hemo-ilmenite from the ore extracted at the Lac Tio Lake mine near Havre St-Pierre, Canada. The analysis of production data suggests that process improvement could be achieved by identifying key variables for the control of the magnetic separation circuit and/or by modification to the circuit flowsheet. The use of a process model was considered to be an effective approach to conduct a preliminary analysis of the circuit with a view toward process optimization. However, the literature contains few detailed studies dealing with the modelling of magnetic separation processes."

Jan 1, 2011

By W. L. Ott, J. E. Hawley, C. L. Lewis

"IntroductionTHE APPLICATION of spectrochemical analysis to metals of the platinum group was advocated by Harvey (3) as follows: ""The spectra of the platinum group metals have been studied less than many of the more common metals. The rarity of occurrence of these elements makes the analysis relatively unusual. Potentially, the analysis of this group is an excellent application of spectrographic methods, particularly in contrast to the tedious chemical procedure"".Wichers (8) divides platinum-metal analysis into three broad divisions as follows :( 1) The detection and estimation of these metals in other materials, e.g., ores, where the amounts present are very small.(2) The detection and estimation of impurities in the refined metals themselves ....(3) The analysis of alloys of the platinum metals .....The present paper deals with the second division: analysis of refined rhodium.Research on spectrochemical techniques for determination of trace contaminants in refined platinum metals was begun at Queen's University in 1949, under the supervision of Professor J. E. Hawley. Since 1953, the work has been continued in the Metallurgical Laboratories of Falconbridge Nickel Mines, Limited. Techniques for spectrochemical analysis of refined platinum and palladium have been published ( 4, 5). A technique for analysis of refined iridium has been developed but not yet published."

Jan 1, 1955

By Jose R. Hernandez-Aguilar, Chris J. Martin, Rob Thorpe

"This study presents an approach to establishing relationships between metallurgical performance and the characteristics of the bubble population (gas dispersion) inside flotation cells. Bubble size Db, superficial gas velocity Jg, and bubble surface area flux Sb (Sb = 6Jg/Db) measurements were obtained along with metallurgical samples in full-size equipment processing different ore types. The gas dispersion was manipulated by changing the operating conditions of the cells (gas flowrate and frother type) and the metallurgical performance (grade-recovery) was determined. In two cases, the Sb had a strong relationship with grade and recovery, hence, Sb could be used as practical operating parameter. In another case, Sb did not correlate with recovery. The reasons were attributed to creating small bubbles using frothers with desired anti-coalescence properties. This illustrated that bubble size was the key parameter for metallurgy rather than Sb.INTRODUCTIONUnravelling the mechanisms that govern the relationships between metallurgical performance and the characteristics of the bubble population (gas dispersion) inside a flotation cell remains a major challenge. Information on this subject is scarce in the literature, particularly, plant-scale data. The report of Jameson and Allum (1984) appears to be the first gas dispersion study conducted in industrial (mechanical) cells. To introduce concepts, some aspects of their work are reviewed here.The prime motivation of that study was to establish whether any particular cell design (among 44 cells surveyed) could produce very small bubbles (< 0.1 mm), which laboratory research suggested would increase the recovery of fine particles. Although one of the outcomes was that the (examined) cells did not seem to produce such small bubbles (Sauter mean1 D32 ˜ 0.9 mm), the analysis highlighted the importance of including other factors. Jameson and Allum indicated that, besides bubble size (Db), other characteristics of the bubble dispersion should be considered, namely: gas holdup ?g – the fraction of cell volume occupied by bubbles, superficial gas velocity Jg – is the gas flowrate divided by the cross-sectional area of the cell and, bubble surface area flux Sb – the rate of production of (new) bubble surface area (m2/s) per m2 of cell cross-sectional area. It should be noted that, whereas Jg, ?g and Db can be measured directly, the Sb is derived: Sb = 6Jg/Db, where Db is usually substituted by the Sauter mean diameter (D32)."

Jan 1, 2006

Cobalt mostly occurs as a minor, but valuable, constituent in most nickel and a few copper ores, however it is not generally found alone in commercially viable deposits. Its concentration and extraction are therefore intimately linked to the recovery of the primary metals and the major task for the metallurgist is to extract cobalt of commercial grade from a much larger mass of either nickel or copper and sometimes both. With a particular focus on Vale Inco?s operations, this paper provides a brief overview of the mineralogy of the main deposits being currently exploited that contain cobalt as a co or by-product. The concentration and then extraction to metal are reviewed and some advances released into the public domain are discussed.

May 1, 2009

By Ralph Harris, Qi Xia

"Gold cyanidation rates are known to be limited by the rate of oxygen dissolution in the cyanidation tanks. The effect of solids loading on the oxygen dissolution rates is not obvious and the results of previous studies are ambiguous. The present paper presents an analysis of oxygen dissolution rates using a ""spent"" commercial gold slurry diluted to various levels of solids loading. It was found, in an 170 litre stirred tank reactor using an inverted cone sparger, that under certain high loading conditions, there was a decrease of as much as 50 %, i.e., there was a halving of the rate of oxygen dissolution as compared to that in clean water. In particular, it was observed that, due to gas flooding of the impeller, there was a drop in kLa even with an increase of gas velocity. Gas holdup reached a maximum value of only 1.7 %. The total power consumption was between 0.06- 0 .10 kw/m3 within the range of gas velocity before flooding occurred. The decrease in oxygen dissolution rate with increased solids loadings is believed to be mainly due to the increase in the apparent viscosity which reduced the turbulence and shearing effect and resulted in larger bubbles and hence reduced the reaction area a. The interrelations between solids loading, gas holdup, flow pattern, power consumption, and liquid mass transfer coefficient are discussed.IntroductionThe reactors generally used in gold cyanidation are Stirred Tank Reactors (STR). Compared with other types of reactors like fluidized bed reactor and column reactor, STR is of particular importance due to its wide application in industry. It is reported that the stirred tank reactor is used for more than 50 % of the world's chemical production (Xu and McGrath, 1996)."

Jan 1, 1997

By Alex Doll, Derek Barratt

"There is a number of comminution tests commonly used in the mining industry. Many of the tests are used for a particular grinding model or mill sizing program and are incompatible with other tests of different models. This paper provides an overview of the commonly used grinding and crushing tests, which models (or practitioners) use a particular combination of tests and draws some relationships between the incompatible tests based on the DJB Consultants Inc. database of projects.Case studies will demonstrate similarities and differences between major mining districts with some comments about homogeneous and heterogeneous behaviour within the grindability results.INTRODUCTIONThere are a number of bench-scale grindability tests in use for sizing and predicting throughput for grinding circuits. Part of the reason for this variety is there are a number of different grinding models in use in the Industry, and those models operate using incompatible test results as input (Doll and Barratt, 2008).By using the database of testwork in the DJB Consultants, Inc. (DJB) Millpower 2000 database (see Table 1), some of the more commonly used tests are compared and relationships will be drawn."

Jan 1, 2011

By N. Romani, R. Provost

"Commissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Québec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.Proper planning of the different commissioning stages and staffing an integrated team are the most important factors required for a successful plant start-up. A strong Operational Readiness plan must be in place as early as the start of construction in order to ensure a smooth transition from commissioning to operations. Plant performance can meet or exceed performance criteria within the required timeframe if the proper group dynamic and good communication is established between construction, commissioning and operations teams.The road blocks encountered are often from systems that one assumes will operate without trouble such as air-conditioning, or design assumptions that were taken years earlier in feasibility process stages, namely the capacity of existing systems that will connect the new plant to the existing facilities. The challenges associated with rectifying these issues in addition to the requirements to properly start-up and operate a new plant without impacting production are great, and it is imperative to have the necessary resources to react quickly to any problems.IntroductionCommissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Québec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.The CDS ProcessA general overview of the CDS process is presented in Figure 1 below. The combined, de-dusted off-gas from multiple kilns is sent to the CDS, which acts as an entrained fluid bed, where the gas is contacted with a water mist, re-circulated solids and hydrated lime. The SO2 from the gas stream and the available calcium hydroxide (Ca(OH)2) from the hydrated lime dissolve in the water and react to ultimately form calcium sulphites and gypsum. The solid residue (referred to as CDS residue), is the primary by-product of the process."

Jan 1, 2016

By L. Boyd, A. Charland, G. Potts, D. Fragomeni, N. O. Lotter

"The Raglan orebody and concentrator has been the subject of study in Process Mineralogy at Falconbridge since 1998. (Lotter and Tuzun, 1998) The orebody is classified into three distinct textural groups, or end members. These are referred to as disseminated, net-textured, and Massive Sulphides, and differ in terms of mineral grain size, nickel grade, hardness, and mineral association. In this paper, it will be shown that the sampling and characterisation of each end member on an individual basis develops a higher-level understanding of the processing requirements and behaviour of the mixture of ore as presented to the mill.The end members have been used in robust prediction of recovery at various grind size p80 from laboratory scale High Confidence Flotation Tests. Weighted mean mixtures of the end members have been mathematically combined to determine impact of textural distribution on metallurgical performance as a function of grind size.The ore end members also vary in hardness and breakage mechanism and have been used to model throughput capability for existing, optimized and retrofit grinding circuits. This modeling has provided a range of expected throughputs as the relative proportions of each end member varies.Finally, the differing grinding requirement per end member has led to the development of grinding and flotation strategy that increases rougher flotation recovery and provides flowsheet options for a concentrator expansion. This leads to further understanding of the plant performance as a function of ore mixture."

Jan 1, 2005

By Andréa Lagacé

"The milling of sulphide ores inherently generates “thiosalts”, a series of partially oxidized sulphur oxyanions (S2O3 2-, S3O6 2-, S4O6 2- etc.), which make control of effluent treatment systems difficult because their natural oxidation produces acid with the potential to lower the pH within the treatment system and/or receiving environment.At the Xstrata Copper Kidd Metallurgical Site, thiosalt oxidation in the Tailings Management Area continues after buffer storage Ponds A and C where lime is added to precipitate metals and elevate the pH to within the required range for discharge. If the additional acidity generated during the continued process of thiosalt oxidation is not neutralized there is a risk that the final effluent will be non-compliant with regulated standards.To mitigate this risk, in 2007 a full scale pilot trial was conducted with hydrogen peroxide in order to force the complete oxidation of thiosalts prior to the lime treatment stations. This method of chemical oxidation had been shown to be effective at Xstrata Zinc’s Brunswick Mine. The pilot results indicated that a maximum of 50% of the stoichiometric quantity of hydrogen peroxide is required to reduce the thiosalt concentration in the No. 2 thickener overflow stream (feed to buffer storage Ponds A and C) to less than detection (10 mg/L); however, treatment was only effective in the presence of a 20 mg/L iron (Fe) catalyst. Since the hydrogen peroxide addition point at the No. 2 tailings thickener overflow typically contains <1 mg/L total Fe, a second reagent, ferric sulphate, was used to increase the total Fe concentration to the required level. This paper describes the set-up and results of the pilot trial which were used in the design of the full-scale plant.INTRODUCTIONTailings Management Area OverviewXstrata Copper’s Kidd Metallurgical Site, located in Timmins, Ontario, is an integrated metal refining facility producing copper, zinc, cadmium, indium, liquid sulfur dioxide, and sulfuric acid from third party custom feeds, and mineral concentrates recovered from its 7,800 tonne per day mill."

Jan 1, 2010

By John Hoffert, Darren Colwell, Greg Tucker, Jeremy Kinch, Greg Rasmussen

"The Kemess Mine, a major producer of gold and copper, is located in north-central British Columbia. Kemess was brought into production in May 1998 by Royal Oak Mines. On February 11, 2000 Northgate Exploration Limited acquired Kemess Mine from receivership. Since acquisition in 2000 Kemess has seen many accomplishments, including the reduction of costs by 40%.One of the largest site capital costs was the construction of the tailings storage facility dam, which when finished will be one of the largest earth filled dam structures of its type. The existing construction design by AMEC called for a kilometer wide rock dam to be built from the 1350 M elevation to the 1504 M elevation at a 5.5:1 slope by hauling over 30 million tonnes of non-acid generating waste rock 7-kilometers from the open pit to the tailings dam, which was highly expensive.Kemess realized an opportunity for cost reduction was possible if the dam could be built from suitable quality tailings sand; however the sand did not meet the neutralizing potential ratio specifications. It was determined that cycloning combined with flotation to reduce pyrite concentration in the sand would produce a non-acid generating product for dam construction. The sand plant design challenges were to remove the sulphides from the tailings to obtain an NPR greater than 2:1 and provide a consistent sand product for the construction with a fines content of less than 15% passing 200 mesh. After a 2-year testing design and construction period, the sand plant was successfully started at the end 2002 resulting in higher than expected sand quality and production rates.This paper describes the plant design phase, commissioning, and operation of the tailings sand plant for construction of the tailing storage facility dam to enable us to meet all the engineering and regulatory requirements. The many challenges faced were successfully met using several innovative designs. The operational, economic, and environmental benefits are detailed."

Jan 1, 2004

By Ian R. Muirhead

Over the past year or so, a number of mining companies have been meeting to examine the role of research in surface mining and, in particular, how to establish a collaborative research effort for the surface mining industry. A review has been completed which has identified the topics that are of interest to the surface mining companies for undertaking collaborative research. This has identified key subject areas such as Operations & Equipment; Maintenance; Environment & Reclamation; and Stability. Specific research projects for the initial research effort have been selected which include Wireless Data Communications, Analysis and Management; Application of GPS in Mining; and Tires for Heavy Haulers. In addition, attention has also been focussed on finding a suitable low cost, but effective, organization to coordinate and manage the collaborative research. The recently formed CONRAD Organization (Canadian Oilsands Network for Research and Development) appears to be a suitable candidate and discussions are ongoing with that group. This paper provides a summary of the review of surface mining research needs and of the status of the establishment of a collaborative research body for surface mining.

Jan 1, 1996

By Patrick Pelletier, Pierre-Alexandre Bossé, Julie Fournier, Gianni Bartolacci, Jayson Tessier, Ahmed Bouajila, Carl Duchesne

"This paper summarizes research into the study of the control of flotation processes based on froth images. The use of numerical image analysis techniques for the extraction of significant patterns (froth structure and colour) from industrial flotation froths is discussed.First, the froth was analysed by the use of the Multivariate Image Analysis (MIA) method to extract the spectral variation contained in a RBG image. The Partial Least Squares (PLS) was applied to develop the empirical model for the prediction of froth grade. The results of this application are illustrated using one industrial case study.Second, the froth was also analysed by Gray Level Co-occurrence Matrix (GLCM) and Wavelet Transform Analysis (WTA) to extract features related more to morphological aspects. Since there is useful information hidden in froth texture, these methods are used as texture descriptor to classify different types of froths.Third, a control strategy based on a froth structure indicator was developed and implemented on an industrial zinc flotation circuit. The feedback controller uses a reagent flow-rate in order to maintain the froth structure at its set point. Process improvements obtained with the implemented control strategy are highlighted.Finally, the feasibility to implement a hybrid control strategy consisting in a froth structure supervision controller based on the froth concentrate grade estimated by MIA and recovery inferred by image analysis is discussed.INTRODUCTIONThe development of control strategies to achieve satisfactory control performance has always been a great challenge for engineers and the need for improved process diagnosis, control and optimization has become more and more evident for the mineral processing industry in the last decades. That is why new process variables need to be measured particularly in highly multivariable processes such as flotation. This industrial process is subject to a wide variety of disturbances mainly generated by frequent and sometimes abrupt changes in physical and/or chemical ore characteristics and also, due to some irregularities in manual process operating procedures. A flotation circuit scheme is always a complex network of more than two dozens slurry streams. Information about those streams (% solid, metal content analysis and flow rates) is important for process diagnosis performance evaluation and control. Also, because of the grade decrease and increasing complexity of the new processed ores, more instrumentation outputs and more powerful and significant pr"

Jan 1, 2005

By Walter S. Bergholz, Michael L. Schreder

"Since Escondida began operations in fiscal 1991, a series of aggressive expansion projects have enabled market share to be increased and ever larger profits to be realized. This was possible due to the very large size of the ore body and its high grade - averaging 2.7% copper from startup through fiscal 1997. The situation has now changed: ore grade is falling rapidly and is projected to be only 1.55% by 2003. Since revenue is directly proportional to ore grade, while costs are proportional to quantity of ore processed, profits will begin to fall dramatically. The Phase IV Expansion Project is intended to forestall this drop in profits by increasing ore processing capacity by over 85%.The Phase IV concentrator is designed for a nominal capacity of 110,000 MTPD and the key to achieving this value is through the proper design of the grinding circuit. This paper presents the general design criteria for the grinding circuit, as well as a description of the facility.INTRODUCTIONThe Phase IV Expansion Project consists of a new copper concentrator located 8.5 km south of the existing operations, a new tailings disposal and water reclaim system, a new concentrate slurry pipeline to the coast, and added concentrate handling capacity at the port of Coloso. The new concentrator has a nominal capacity of 110,000 tonnes per day (MTPD), compared to the existing concentrator’s capacity of 127,500 MTPD. The Laguna Seca concentrator is based on using the largest and most efficient ore grinding mills now available.The concentrator has been designed for a 110,000 MTPD nominal capacity. The process design criteria for the Phase IV project were established from in-house operating information and from test work. Unlike a green field project, Escondida already had an operating plant and it processes ore from the same pit that feeds the Phase IV plant. It is expected that the current mineralization will be similar for the first 6 years of operation of the new project. Therefore, some of the current plant operating conditions were incorporated directly into the design criteria."

Jan 1, 2004

By P. Radziszewski

"The comminution energy curve is a profoundly simple graphical technique that displays detailed operating efficiency information for industrial comminution processes. The database underlying the methodology has recently more than doubled, to now contain a substantial fraction of the international comminution output (1.7 billion tonnes of rock per year) across more than 8 major commodities. This increase has deepened the analytical capabilities and effectiveness for assessing comminution circuit performance in relation to comparable operating mines. This paper will explore how the energy curve methodology can be used to examine the ability of stirred mill technologies to increase efficiency.Specifically, this paper explores how the energy curves methodology can be used to present energy efficiency gains achieved at three mines employing a stirred mill technology under different duties. The first of these cases studies was conducted by Rosa (2014) who compared the performance of two ball mills operating in parallel with a Vertimill in the regrinding circuit at the Samarco Iron project in South East Brazil. The Vertimill was found to achieve the same product specification while consuming 40% less energy. Brissette (2010) investigated the impact of grinding media on the performance of both ball mills and Vertimills. The energy savings achieved varied from 10% to 40% for the ball mills and 30% to 60% for the Vertimills. Lastly, Bergerman (2012) investigated the operating conditions of the Sossego regrind circuit from 2006 to 2011 against design specifications and laboratory testing. The operating work index of this circuit varied from 5.2 kWh/t to 44 kWh/t over this 5 year period. The full suite of energy curves"

Jan 1, 2016

By Tim Edwards, Richard Triglavcanin, Ian Arbuthnot, Darren Colwell, Brad Garraway, Ken Roberts

"In the mineral processing industries, there is an increasing need to design thickeners which are able to produce high density underflows usually referred to as “paste”.The behaviour of a flocculated suspension in compression needs to be well understood in order to arrive at a reliable thickener tank configuration (i.e. diameter, cone angle and depth) for a required paste result.As a suspension approaches paste consistency, it’s fluid characteristics change markedly. It develops a high yield stress, and may have an increased tendency to form agglomerates, which lead to a phenomenon known as “rotating beds”, “donuts”, or “islands”. These characteristics present challenges to the designer of the rake mechanism.The subject paper addresses the requirements for designing a paste thickener, covering the following topics:o Testwork for thickener sizingo Design of rake mechanismso Suspension rheology and effect on designo Case studiesTESTWORK AND SIZING FOR PASTE THICKENERSThickening slurries to the maximum possible density (paste) is becoming increasingly common. Applications such as Autoclave feed thickeners, paste backfill and some counter current washing (CCD) circuits are all examples of potential paste thickening applications. The principle of paste thickeners is that the compression zone is much deeper than on either high rate (HRT) or high compression (HCT) units; generally 3 metres or more. As the compression zone gets deeper, theunderflow density for a given flux rate (tph/m2) increases, as a result of two factors:1. Longer bed settling time. Settling flocs move relative to one another and release interstitial fluid when they are in compression. Increasing bed residence time achieves higher density underflow as more fluid is removed.2. The nett weight of the bed creates a compressive force on the settling flocs. This force increases with depth, so that the flocs at the bottom of the bed experience the highest compressive force. This represents the driving force to expel interstitial fluid and hence increase bed density."

Jan 1, 2005

By Sam Palombo, James José Varela

"Washing can be defined as the process used to eliminate or reduce the dirt (presence of fines or slimes) of one material. It is also the basic and oldest process applied to ore preparation for further concentration. This process, in combination with commnution and screening, form the so called washing plant and in many cases produce end products. This work describes the factors that influence the performance of the washing process and main washing technologies used in the mineral processing industry.The Hydro-Clean represents, since 1998, a state of the art technology in this area and is comprised of one of the most innovative solutions developed at HAVER & BOECKER. HAVER & BOECKER design and manufacture technology for mining and related industries. Today the Hydro-Clean is manufactured and sold throughout the Haver Screening Group (HSG) which is comprised of HAVER & BOECKER Maschinenfabrik Münster, HAVER & BOECKER Latinoamericana – Brazil and W.S. Tyler Canada.The Hydro-Clean is a washing technology based on utilization of high pressure water jets. To follow we will discuss how the Hydro-Clean’s different modes of operation result in several advantages related with mine waste reduction, recovery of saleable product, lower capital costs, superior washing results, less stress for the material, a wider range of application and less maintenance cost. Aside from these positive factors, its lower operation costs related to the consumption of energy and water are presented. It is important to note that the quantities, tonnages, data and management concepts presented in the paper are accurate for the time of writing and are subject to change and modification as operations progress."

Jan 1, 2009

By N. I. Basuki, E. T. C. Spooner

"The Bongara area, northern Peru, contains Zn-Pb mineralization with characteristics typical of Mississippi Valley-type (MVT) systems. The northwest-southeast-trending late Triassic-Jurassic car¬bonate host rocks of the Pucará Group were locally replaced by early (D1) and late (D2) dolomite. Fluid inclusion microthermometric data from dolomite and sphalerite are typical of MVT ore fluids (78° to 187°C; ~15-23 wt.% CaCl2 equivalent), and do not show apparent covariation between temperature and salinity.Homogenization temperature data from D1 and D2 dolomite show a decrease from northern (mean Th = 138°C) to central (mean Th = 126°C) to southern areas (mean Th = 102°C), suggesting fluid flow from north to south. Assuming a geothermal gradient of ~30°C/km and an average surface temperature of ~20°C, the lower temperature limits might approximate the ambient host-rock temperatures, whereas the upper temperature limits may represent minimum temperatures of a deeper aquifer, probably at a maximum depth of ~6000 m. The lower temperature limits are also similar to the estimated temperatures if dolomitization and mineralization took place in the Late Cretaceous at ~2000-3000 m depth, probably during the formation of the Peruvian fold and thrust belt near the present day Peru-Ecuador border.Fluid inclusion data show that the fluids in each studied location had relatively uniform temperatures and salinities during dolomitization and mineralization. A significant salinity drop and a slight temperature decrease are observed during late calcite precipitation, suggesting mixing of brines with dilute, cooler fluids."

Jan 1, 2009

By D. Brand

"The risk management objective of the AMIRA Code of Practice for Metal Accounting has seldom been systematically investigated in the literature up to the authors’ knowledge. Risk is defined in the Australian Standard on Risk Management (AS/NZS 4360:2004), as “the chance of something happening that will have an impact on objectives”. The simplified economic analysis performed in this paper has lead to define “something happening” as measurement non-representativity and “impact on objectives” as NSR loss from the optimal NSR. This has pinpointed a missing link being the establishment of a relation between NSR in flotation plants and measurement representativity. The proposed framework, referred to as the total cost of representativity, answers the previously unanswered question of how much accuracy/reproducibility is fit for purpose in a given flotation plant. Authors readily acknowledge that it is way easier to assess the cost of accuracy/reproducibility than the cost of inaccuracy/irreproducibility. However, this exercise not only answers previously unanswered questions but also establishes an essential link with operational excellence. This paper exposes why such operational excellence could neither be attained nor proved without a state of the art metal accounting system. This should impact not only how metal accounting systems are audited/designed/refactored, but also how flotation plants are designed.IntroductionBecause representative metal accounting is a vital source of information for the financial accounts of a mining/metallurgical company, the need for a code on metal accounting was recognized in 2001 and a team was formed in 2003, under the sponsorship of several major mining houses, to produce such a code. Table 1 exposes the two main objectives of this AMIRA Code of Practice for Metal Accounting."

Jan 1, 2017

By E. M. Watkin

"Although Canada has achieved one of the highest living standards in the world, people and organizations have, over the past decade, begun to question the cost and means of this achievement. Concern has been expressed about the degree of environmental disturbance arising from industrial activities which have greatly contributed to our increased living standards. These industries include hardrock mining, pit and quarry operations, hydro-electric schemes, various agricultural enterprises and urban land developments.In the construction and operation of the above industries many environmental problems arise because the natural vegetative land cover is destroyed or drastically disturbed. Disturbance may occur to such a degree that revegetation is di ffi cult, often it appears impossible. Portions of the environment around such industries remain aesthetically unacceptable and appear to offer little or no potential for future resource use in wildlife, recreation or agriculture.The general public cannot dissociate itself from the activities of the aforementioned industries. It has, over many years, accepted the benefits and conveniences arising from those activities. Despite this, the increasing level of public concern imposes upon industry a need to alleviate or repair past, present and future environmental disturbance. Therefore it is incumbent upon industry to modify present technology or develop new techniques which would allow the disturbed environment to be easily and rapidly repaired."

Jan 1, 1975