Search Documents

By Z. Huda

The effect of various percentages of cold-working and recrystallization on the microstructure and hardness of commercially-pure aluminum plate, has been studied. The 'A critical deformation for the aluminum, has been determined. Experimentation involved cold rolling and recrystallization processes followed by quantitative metallographic practice and the hardness measurements. The raw material chosen was a plate of commercial aluminum which was cold rolled to different percentage of cold-work and then recrystallized by heat treatment at 150°C. The critical deformation percentage of aluminum was computed to be around 30% of cold-worked.

Jan 1, 2007

The process of gold recovery by gravity concentration is incorporated in the metal recovery flowsheet at seven Newmont Mining Corporation owned mining operations in Australia, North America and Africa. In 2009 gold recovered by gravity processing was equivalent to nine percent of Newmont's total gold sales of 5.3 million ounces. This paper will discuss these applications in detail including a review of plant flowsheets and presentation of recent operating results. Operating performance will be discussed with reference to ore characterisation procedures, interpretation of results, design considerations and optimisation practices as they relate to the recovery of gold by gravity concentration.

Jan 1, 2011

By K. V. Lindell

Introduction This paper describes a recent innovation in the design and construction of mine headframes. A reinforced concrete headframe was built by using sliding forms. A concrete headframe of conventional design was originally considered, but investigation of this project showed that it was doubtful if the bearing strength of the soil was sufficient to support the great weight of a structure of this type. In addition, the slope and the fractured condition of the serpentine bed-rock did not permit satisfactory piling. A conventional steel headframe with storage bins was then designed, but, due to the steel situation, delivery promises were set back many months. The concrete headframe was again investigated, and a design was adopted incorporating a circular headframe lower in height than that first considered, with skips discharging into a smaller surge bin. The upper section of the shaft collar was strengthened to result in a stable structure which would be supported by bed-rock, as well as by the concrete and steel lining of the shaft itself.

Jan 1, 1948

By J. Walker, G. E. Kim

Since May of 2000, Mogas Industries, in partnership with F.W. Gartner Thermal Spraying Co. and using the services of Perpetual Technologies, has invested time, energy, and resources towards developing novel ball valves for high-pressure acid-leach (HPAL) service. In addition to developing new valve designs, an aggressive coatings development effort has been undertaken to improve the protective quality of the coatings so as to enhance the performance and extend the life of valves in severe HPAL conditions. In 2001, Mogas Industries qualified and applied a nanostructured titanium oxide (n-TiO2) coating for gold and nickel/cobalt HPAL services. The n-TiO2 coating provided dramatically superior protection against abrasive and erosive wear, fared very well against high-pressure autoclave corrosion testing, and has performed well in HPAL service.

Jan 1, 2004

CHALLENGES TO SCHEDULE/BUDGET Shortage of people (contractors, vendor support, engineering, staff) 2007 projects off the shelf Increase in metals prices Shortage of large tires Reserve increase Size of mine Unskilled labor force Community/government relations Limited access into valley English to Spanish SOLUTION Line 1 Line 2 concurrent construction, EPCM engineering review, advance scheduling Placed line 2 orders earlier Hedged currency, bulk orders Strategic alliances Flexible design Plan Deliveries Training, multiple contractors Engagement Built/upgraded roads Technical translators

May 1, 2010

By N. Ogbonna, D. G. Dixon

Although heap bioleaching has been recognized as an economic alternative for treating low grade mineral ores, the underlying physical, chemical and biological processes involved are complex. A detailed investigation into the dynamics of heap bioleaching processes has provided much insight into the underlying complexities, and has led to the development of a sophisticated modelling tool - HeapSim. This tool can be of great help in the design and operation of heap bioleaching processes. In this paper, the mathematical model implemented in HeapSim is examined. The model takes into account mineral kinetics, particle level effects, bacterial growth, oxidation and adsorption, gas absorption, pore diffusion, bulk advection, gas balance and heat conservation. Three case studies where the model has been applied are briefly discussed. Computational Analysis in Hydrometallurgy 35th Annual Hydrometallurgy Meeting held in conjunction with the 44th Annual Conference of Metallurgists of CIM Calgary, Alberta, Canada Edited by

Jan 1, 2005

By R. L. Alexander

"Madawaska Mines Limited, incorporated in 1975 is the successor to Faraday Uranium Mines Limited. The history of the latter's mine development and corporate changes are outlined. This paper describes the geology of the Bancroft area and the rock types found in the mine, particularly the pegmatite which is the host rock for the uranium. The structure, mineralogy and distribution of the ore shoots are described with the method of grade control and mine development. The paper concludes with a summary of the production and mineral reserves.Location, Access, and PropertyMadawaska Mines Limited is located in Faraday Township, Hastings County, Ontario. The mine is in the N.T.S. quadrant 31 F/ 4, Bancroft sheet and near 46 degrees 01 minute latitude, 77 degrees 46 minutes longitude. The mine is one-half mile north of Highway 28, five miles (8 km) west of Bancroft, and is accessible by various highways from Toronto, Ottawa, Peterborough, and Belleville. (Fig. 1). A landing strip for small aircraft is located at the northwestern edge of Bancroft. Bancroft is a modern community with a population of 2,400. The company has the mineral rights to 2982 acres (1207 hectares) surrounding the mine workings and plant which are situated in the north parts of Lots 16 and 17, Concession XI, Faraday Township."

Jan 1, 1986

By E. Pallumbo, N. Szwedska, R. Asselin

"This paper highlights the results of collaboration between geology, mining and mineral processing teams during the restart of the North American Lithium Project, located near La Corne, Quebec, Canada. This collaboration was central in ensuring a cross discipline harmonization of design parameters and key inputs, all of which allowed for the development of an optimized life of mine plan suited to the particular needs of the operation.INTRODUCTION In July 2016, North American Lithium Inc. (NAL) began the process of restarting operations at the former Quebec Lithium Mine, located in the municipality of La Corne, Quebec, Canada. The North American Lithium Project (the Project) as it is known today, is the latest chapter in the history of this property. In order to provide a robust foundation for the project, multidisciplinary collaboration was instituted between the geology, mining and metallurgy teams. Despite the intrinsic link between these departments, in many instances their work is completed separate from one another; in silos. This collaboration highlighted specific drivers in the mining value chain that could be exploited to ensure that a saleable product could be produced effectively. This paper explores some of the concepts and strategies that were developed during the feasibility study that supported the project restart (excerpts from the study technical report have been used throughout this paper). PROJECT HISTORY In 1942, prospectors identified the presence of numerous spodumene-bearing pegmatite dykes on the Property. This led to additional interest and exploration drilling campaigns. In 1955, Quebec Lithium Corp. (QLC), who had acquired the property, began construction of an underground mine with mill facilities located on the surface. Operations began the following year at a production rate of 1,100 tonnes per day. A historical cross-section view of the underground mine is shown in Figure 1. In 1959, QLC began the construction of an on-site lithium refinery to produce lithium hydroxide. The refinery was finally operational by 1963. Mining and processing operations continued until 1966 when activities were halted due to a labour dispute. The property was sold and a few years later attempts to resume production were unsuccessful. Property ownership changed several times again until being acquired by Cambior in 1987. In the early 1990’s the existing mine and mill facilities were sold and the mine site rehabilitated"

Jan 1, 2019

By L. Furtenbach, T. Möller

"Grinding mills are the heart of the mineral processing plant, and are production-critical machines which are required to achieve high availability. Liner wear life and a liner design that promotes ease of installation are important variables to achieve a high level of mill availability. Increased mill size results in more mill internal surface to protect, and more liner components to install and remove. This drives designers toward an increase in liner size to minimize the number of components to be installed by the liner handler. The liner attachment method can also have a large impact on mill availability as well as safety during installation.This paper outlines the experience from the development, installation and follow-up of liners installed in two 38' x 45' AG Mills at Boliden Aitik in Sweden. A new Poly-Met shell liner concept has been developed to minimize the number of liner components. The new Poly-Met shell liner components are made much larger than conventional Poly-Met or steel liners. This reduces the number of components to be installed/removed by the liner handler and helps to minimize installation time and consequently down- time. A new attachment system has also been developed to eliminate the need for the installation crew to be in the “drop-zone” of the shell liners while installing the liner bolts.One interesting aspect of this project was the requirement to predict liner life for these new large format AG mills. The existing 22' diameter mills at Aitik provided a base-line reference for this purpose, and DEM studies were used in the project development stage to predict the wear life of shell liners for the new 38' diameter AG mills. The results from this study are included."

Jan 1, 2012

By W. R. McClelland

GOLD-BEARING ores, representing many types, are found widely distributed through the Province of British Columbia. They range from those which by their nature may be considered as complex, to those whose mineral characteristics are simple. Those in which the gold is associated with metallic sulphides provide particular milling and metallurgical problems, the solution of which involves not only detailed laboratory investigation but also a careful consideration of economic factors. The location of an ore-body may have a deciding influence on the adoption of a method for the metallurgical treatment. Whether the ore should be treated with the object of recovering the gold as bullion or as a shipping concentrate is often dependent on such topographical considerations as the position of the mine at or near tidewater or within a reasonable overland distance of a smelter. British Columbia is fortunate in having the Trail smelter situated in the southern part of the Province, and the smelter at Tacoma, Washington, is accessible for coastwise traffic. Both of these provide a ready market for most types of gold-bearing concentrate. In order that the results obtained by laboratory tests may give a fair indication of what should follow in mill operation, it is essential that the test sample should represent as closely as possible in mineralogical character and in grade the ore that eventually will constitute the feed to the mill. In the early stages of mine development this consideration is sometimes overlooked and samples of a much higher grade than would be representative of run-of-mine ore are submitted. Flotation tests on such a sample of ore high in sulphides may show a low ratio of concentration, bu.t if the actual run-of-mine ore is lower in sulphides the mill operation will reveal a much higher ratio. The recommendations for treatment based on the results of laboratory tests may have been against concentration, when in actual operation this would be the most suitable method of treatment. Recommendations based on laboratory tests are necessarily from the results of work carried out on the sample submitted, modified only by such other economic or topographical information as may be known to the investigator. This paper deals with a few of the gold ores found in the six mining districts of British Columbia and is based on investigations made in the Ore Dressing and Metallurgical Laboratories of the Mines Branch, Department of Mines, Ottawa.

Jan 1, 1937

By V. I. Lakshmanan

Recycling helps to save energy and is good for the environment. It is also important for preserving the limited natural resources. In addition, recycling creates economic benefits and frees up space at the landfill sites. Process Research Ortech Inc. (PRO) has conducted extensive testwork in the area of waste processing and recycling. A process was developed for the recovery of Zinc from galvanized steel by alkaline leaching followed by solvent extraction and electrowinning. Extensive testwork has been conducted at PRO to obtain a useful by-product from rice husk. Rice husk was combusted in a gas/solid reactor to obtain an environmentally acceptable amorphous silica ash suitable for use in high strength concrete. In another development, vanadium was recovered from fly ash by separating carbon first, followed by alkaline pressure leaching, solvent extraction and precipitation. PRO has also developed an environment friendly process for treatment of industrial wastewater for its reuse to obtain zero or minimal effluent discharge. In this paper, four case studies related to recycling of zinc scrap, controlled combustion of rice husk, processing of fly ash, and reuse of waste water will be discussed.

Jan 1, 2011

By J. Kalynchuk, R. Poulin, R. Pakalnis, D. Peterson

"A market survey of all underground mines in Canada (Fig. 1) was completed to determine the ex1ent to which cable bolts are being used as ground support. One hundred and nine questionnaires were distributed with 65% of them being returned completed. As a result, the quantity, types and locations of cable bolt installations have been determined. In addition, the grout pumps used, time required and cost of installations have been addressed. The popularity of other support types used in underground mines is summarized.IntroductionRock reinforcement consists of installing support within the rock mass (internal) or within the excavation (external). Within the past twenty-five years several new types of ground support have been introduced within the mining industry. Cable bolts were first introduced to the Canadian mining industry in the 19605 (Gramoli, 1975).Cable bolts have gained increased acceptance as a method of ground support during the past decade. The cable bolt is comprised of one central wire surrounded by six slightly smaller outside wires and typically having an over-all diameter of 15.2 nun to 15.9 nun (0.6 in. to 0.625 in.). The cable wires are made from high-strength steel with an ultimate strength of 26 tonnes (58 000 Ibs) (Goris, 1990). Current cable bolting practice consists of cement grouting one or more steel cables within a drill hole in order to reinforce the surrounding rock mass. Cable bolts are a form of internal support and are generally used in open stoping and cut-and-fill mining methods (Fig. 2).They can be either tensioned (active support) or untensioned (passive support) and may be of any length, though for underground mining applications, they are generally less than 20 m (65.5 ft) and are untensioned. A major advantage compared to previously used ground support is that the cables are flexible and can be coiled to approximately 1 m (3.3 ft) diameter coils allowing relatively long support to be installed in areas with limited head room (1.8 m).With the advent of bulk mining methods which require comparatively large stopes, it has necessitated the use of relatively long support tendons to stabilize the large spans being created. As a result, the use of cable bolts for ground support in mines has increased significantly within the past decade."

Jan 1, 1995

By J. C. White

"This paper was prepared for and presented at a lecture series on ""Materials Randling"" at McGill University. The development of trackless mining at Gaspe Copper Mines, Limited is described, showing the changes in mining method and the part played by the mobile equipment in the evolution of this highly mechanized underground operation. Comparisons of loading and hauling machines are given and an attempt is made to predict some possible future developments.INTRODUCTIONTHE PROPERTY OF GASPE COPPER MINES LIMITED is located in the Gaspe Peninsula of the Province of Quebec, 60 miles west of the village of Gaspe and 25 miles south of the St. Lawrence River. The original discovery of low-grade ore was made at Copper Mountain in 1921. Subsequent exploration revealed the richer Needle Mountain orebodies, and eventually in 1951 the decision was made by Noranda Mines to build the mining, concentrating and smelting complex (Figure 1). Construction and development of the mine was commenced in 1952 and production started in 1955."

Jan 1, 1968

By M. Krasowska

Dynamics of collision and kinetics of the bubble attachment to hydrophobic solid plates (Teflon) of different surface roughness were investigated. The experiments were carried out in such a way that probability of the collision and probability that the detachment will not occur were equal always 100%. Thus, it was possible to determine effect of the surface roughness on the bubble attachment (three phase contact formation, TPC) only. A high-speed camera (1182 Hz) was used to record the velocity variations, bouncing and time of attachment of the bubble colliding with Teflon plates having different surface roughness (5 different plates). Roughness of the plate surfaces was modified in a mechanical way using different abrasive papers. It was found that the roughness had a crucial influence on the time-scale of the TPC formation and attachment of the bubble colliding with the Teflon plates. Despite high hydrophobicity of all plates (contact angles 1100 -115º) it was observed that at the smoothest surfaces (called "Teflon I" and "Teflon II" and having surface roughness below 1 um) there was no attachment during the bubble first collisions. Prior to the attachment four or more "approach?bouncing" cycles of the colliding bubble were observed there and simultaneously the bubble shape varied rapidly within time intervals below 0.85 ms. Time of contact of the colliding bubble with the Teflon plates was very short; 2-3 ms. These results indicate that during that short time of the collision the liquid layer separating the colliding bubble and the solid surface did not reach a critical thickness of its rupture.

Jan 1, 2006

By J. Oyunaa, P. Munkhbaatar, A. Sarnai

"The molybdenum mining process used at Mongolia Erdenet Company is a selective flotation of molybdenite from the copper porphyry ores in which the extraction of molybdenum comes as a byproduct of the ongoing copper production.The mineralogical composition of molybdenum concentrate is 99.4% molybdenite (MoS2), 0.09% molybdenum oxide (MoO3), 0.52% powellite (CaMoO4) and wulfenite (PbMoO4) and content 47.76– 47.92% molybdenum, 1.5–2.67% copper, 0.04% renium.From compared solvents sodium and carbonate and ammonia are like extracted molybdenum than hydrochloric acid, which contained 96.23–97.72 p.c. of its total amount. Hence to take into consideration abundance, cheap and suitable for analysis and processing the molybdenum concentrate ammonia is choosing as a basic solvent. By direct evaporation of ammonia extract solution, we obtained ammonium ortomolybdate, which contains 73.47% MoO3. INTRODUCTIONMolybdenum occurs in the earth’s crust in an abundance of about 10–14%, mainly as molybdenite, MoS2. Small quantities are also associated with other metals having similar chemical properties. Thus wulfenite (PbMoO4) is found in oxidized parts of sulfidic lead deposits in many regions of the world; powellite [Ca(Mo,W)O4] is a calcium molybdate usually formed from the modification of molybdenite in deposits containing tungsten as scheelite (CaWO4) and tungsten substitutes for molybdenum up to about 10%. Ferrimolybdite (Fe2Mo3O12·8H2O) is the product of oxidation of molybdenite in the presence of iron (III) compounds. Molybdenite is the primary source of molybdenum. Should demand for molybdenum rise so that additional sources become necessary, wulfenite, powellite, and ferrimolybdite may become commercially significant. Molybdenum ore is mined by underground and open-pit methods. A typical primary molybdenum ore body contains 0.05–0.25% Mo, and secondary ore bodies (copper porphyry ores) average 0.3–1.6% Cu and 0.01–0.05% Mo. Flotation remains the preferred and almost exclusive method of upgrading the molybdenite mineral to an industrial-grade molybdenite concentrate containing 90–95% MoS2, the balance being gangue (Habashi, 1997)."

Jan 1, 2016

By Ausenco Engineering Canada

"This paper demonstrates the selection of grinding circuit technology for a number of recent projects including discussion of the key drivers and the role of energy efficiency. Decreasing head grades combined with a strong and sustained increase in operating costs has forced miners to examine increased project size, increased equipment capacity and efficiency improvements in order to reduce their unit operating costs and improve overall project economics. Comminution energy consumption, safety and capital cost considerations play a critical role in the success of projects. This paper presents some key guidelines for a successful and cost effective comminution circuit design and includes a case study on three projects, outlining the issues and the drivers which led to the ultimate circuit selection and the critical role that energy efficiency played.INTRODUCTIONComminution circuits for minerals processing are selected based on their suitability and efficiency in reducing run-of-mine ore to the desired feed size for the downstream process. The input material (ore) properties and downstream process requirements are the key determinants and there are standard approaches for each circumstance.The minerals processing industry has been a fast adaptor of efficiency improvements based on increasing capacity of equipment (e.g. trucks, crushers, mills, pumps) but less successful in adapting radically new technologies that disrupt incumbent flowsheets or processes.The installed power of grinding mills has increased linearly over the past 25 years (Meka & Lane, 2010) and pumps and classification equipment have kept pace. The autogenous grinding (AG) and semiautogenous grinding (SAG) mills displaced stage crushing as a dominant method of coarse rock breakage in many applications causing crusher manufactures to increase the capacity of cone crushers to meet the competitive demand.Examples of new comminution technology in the 20th and 21st centuries are the development and adoption of cyclone classification in the 1940s (Newtech, 2016), AG milling in the late 1950s, vertical grinding mills in the 1980s, high pressure grinding rolls (HPGRs) also in the 1980s and ultrafine milling technology in the 1990s (Meka & Lane, 2010)."

Jan 1, 2016

By I. C. Brown

Introduction Many tables of nomenclature for igneous rocks have been introduced from time to time, and each has its strong proponents. As a result, any discussion of igneous? rocks is apt to prove confusing unless the names used for these rocks are defined. This ?became so obvious to a discussion group, formed by the members of the Geological Survey of Canada in 1948, that an attempt was made to establish a scheme of nomenclature that could be used by any member mapping anywhere in Canada. The writer was asked to co-ordinate the ideas presented by individuals in the discussion group, to arrange them in tabular form, and, later, to distribute copies of the resultant table to Canadian universities, provincial geological surveys, and some other geological discussion groups. Many useful suggestions and criticisms were received, were studied ?by members? of the original group, and, so far as practicable, were incorporated in the scheme of nomenclature. The result is the table presented here. This nomenclature of igneous rocks is at present being used by most members of the Geological Survey of Canada who are working with igneous rocks, and by some Canadian universities. We hope it will be found useful and be more widely accepted. With this idea in mind, certain principles were adopted in drawing up the nomenclature.

Jan 1, 1952

By X. G. Zhao, M. Cai, L. K. Ma, P. F. Li

"Crack initiation stress is one of the characteristic stress thresholds in the rock deformation process under compression. By analyzing AE responses of brittle rocks in uniaxial compression, a new method which is called cumulative AE hit (CAEH) method is proposed for determining the crack initiation stress. An advantage of the CAEH method is that the method removes the user's subjective judgment. To verify the CAEH method, uniaxial compression tests with AE measurement using 77 crystalline rock specimens were conducted. The test specimens cover eight rock classes with different mineral grain distributions. Crack initiation stresses of these specimens were determined by the proposed CAEH method and the LSR method, and the resulting mean crack initiation stresses determined using the two methods were comparable. In addition, taking one rock class with 20 specimens for example, the mean crack initiation stresses determined using the CAEH method and those from several established strain-based and AE-based methods were similar. Hence, the CAEH method can be used as an alternative method for crack initiation stress determination.INTRODUCTIONExperimental observations indicate that the failure process of brittle rocks is associated with crack initiation, crack propagation, crack damage and final strain localization (Brace et al., 1966; Bieniawski, 1967; Lockner, 1993; Wawersik & Fairhurst, 1970). Compression tests on cylindrical specimen are often used to characterize the crack development process. The crack initiation stress (sci), crack damage stress (scd), and peak stress (sc) represent important stress thresholds during the failure process of brittle rocks. Among the three characteristic stress magnitudes, sci is difficult to be determined objectively, directly from examining the stress–strain curves. Some researchers argued that sci obtained from laboratory compression tests is an important parameter for estimating the spalling failure observed in brittle rocks around underground excavations (Andersson et al., 2009; Diederichs, 2007; Martin, 1997). sci can also be used to estimate rock tensile strength and Hoek-Brown failure criterion parameter mi (Cai, 2010). Over the last 40 years, various strain-based methods have been proposed to determine the crack initiation stress in compression tests (Brace et al., 1966; Diederichs, 2007; Eberhardt et al., 1998; Lajtai, 1974; Martin & Chandler, 1994; Stacey, 1981). Nicksiar and Martin (2012) proposed a Lateral Strain Response (LSR) method for establishing sci for low-porosity rocks. Meanwhile, they also used different strain-based methods to evaluate sci of Äspö diorite, and the results showed that all strain-based methods gave acceptable crack initiation stress values. Subsequently, they utilized the LSR method to further investigate the crack initiation stresses in igneous, metamorphic, and sedimentary rocks in compression tests (Nicksiar & Martin, 2013). Compared with previously proposed strain-based methods, an advantage of the LSR method is that it removes the user judgment when interpreting sci. However, the use of the LSR method relies on accurate determination of scd and on having a polynomial fitting equation to find the maximum LSR value."

Jan 1, 2015

By Margaret Anne Stephenson

Today, in Australia, it is increasingly common to see agreements between Indigenous peoples and resource companies being achieved generally as Indigenous Land Use Agreements or agreements pursuant to the ?right to negotiation? process under the Native Title Act 1993 (Cth). Despite progress in this area, resource development on Indigenous lands is not without its challenges for both the resource proponents and the Indigenous parties. History demonstrates that resource development on Indigenous lands has produced struggles between the traditional owners of the land and the resource proponents. In Australia their relationship is generally defined by issues of access to land and assuring continued access to the land for the life of the project. In this context, divisions in Indigenous communities often emerge. The proposed resource project can have the effect of polarising members of an Indigenous community. It may be regarded by some traditional land owners as an advantageous opportunity for the community and by others as a hazard to country and culture. The process of agreement making has proved not only a test for the Indigenous community but also for the resource proponent. In this paper we undertake a contemporary case study of a proposed Australian resource related-development project on Indigenous lands. This project involved a multi-billion gas hub precinct proposed at James Price Point in the Kimberley region in Western Australia. The James Price Point proposal produced a litany of challenges for all parties. The traditional owners faced fundamental social and human rights issues, including a minority opposition to the project, the project's potential cultural heritage impact, the threat of compulsory acquisition of their native title interest by a State government due to an initial failure to settle an agreement, a fracture of their unsettled land claim and a minority rejection of the agreement ultimately reached. Additionally, the ?green? lobby also rejected the proposed gas hub on environmental grounds bringing the green lobby into direct conflict with both the traditional owners in favour of the project and the resource proponent. Ultimately, Woodside announced its decision not to proceed with the proposed gas precinct at James Price Point, in April 2013. In this paper we analyse the complexity of the James Price Point gas hub negotiations with the traditional owners which resulted in an Agreement that promised to deliver substantial benefits for the Indigenous communities. We question why such a favourable and beneficial agreement for the Indigenous community also produced the plethora of challenges and concerns and we consider how future negotiation processes could be better structured to avoid the difficulties that have confronted Indigenous land owners and resource proponents alike.

Aug 1, 2013

By David Thomas, Charles Harper, Brian Watters

The Star-Waddy Lakes area lies withjn the northeasterly-trending early- to mjd-Proterozoic volcanoseilimentary-pl utoruc belt referred to as the La Range Domllin. In the area investigated the domajn is composed of the Central Metavolcaruc Belt which is bordered by metasedimentary belts of the Crew Lake and MacLean Lake Belts to the northwest and southeast respectively. The boundaries between the Central Metavolcanic Belt and the flanking belts are generally marked by prominent zones of shearing. The volcanosed imentary succession is intruded by a variety of ultramafic to felsic plutons which, on the basis of lithology, field relations and geochronology, can be broadly subdivided into three groups or episodes. These are: a) an 'early' (ea. 1866 Ma), possibly subvolcanic, episode marked by composite intrusions ranging from gabbro-diorite to granite, b) an 'intermediate' (ea. 1854 Ma) plutonic event distinguished by more homogeneous felsic intru ions ; and c) a 'later' (ea. 1835 Ma) event characterized by leucocratic quartz-rich grani te intrusions. The La Range Domain has undergone polyphase deformation with a strongly developed northeast-trending structural grain. Large scale folding is manjfested by large regional sy nforms, arcuate and triangular patterns associated with many of the plutons and by tight to isoclinal folds within the adjacent metasedimentary belts. Inhomogeneous strain characterizes much of the Star-Waddy Lakes area. With strain gradients being typically very steep, zones of high strain consisting of zones of extreme extensional fabrics, discrete shearing, as well as broader zones of cataclasis and structural slicing, are often juxtaposed with areas of relatively minimal deformation . Dilation structures tend to favour these zones of highly contrasting strain. Late, brittle fractures, faults and shear zones are widespread and appear to be particularly important as loci for gold mineralization. Metan1orphic mineral assemblages indicate that upper greenschist to middle amphibolite facies conditions were attained. Geological and geochenucal evidence indicates that the Central Metavolcanic Belt evolved in an island arc environment. Metavolcanic rocks from both the Waddy and Star Lakes areas display similar characteristics on variation diagrams (e.g. AFM and the Jensen cation plot) in that the dominant trend is calc-alkaline with some basic to intermediate types having a mildly tholeiitic character. A few samples from the southern end of Lower Waddy lake display komatiitic to basaltic-komatiitic afl'injties. The relatively immobile minor and trace elements (e.g. Ti , Zr, Nb, Y, Cr) provide reliable characterization of the metavolcanics, particularly of the basalts, which have highly distinctive trace element properties. Geochemical patterns for the basalts are similar to those for modem volcanic arc basalts. Low initial 87Sr/86Sr ratios (0.7017 - 0.7019) are consistent with a subduction-related origin for the volcanics. The major plutons have chemical properties typical of volcanic arc granites and are largely calc-alkaline in character, showing little chemical variation from the volcanics.

Jan 1, 1986