Search Documents

By K. E. Prince, S. Burling, R. J. Ring, M. K. Maley, W. R. Taylor

Vanadium occurs as a component of carnotite, which commonly occurs in calcrete type ores, and in association with uranium in some sandstone-hosted deposits. Increasing demand for vanadium, which is used in high-strength steel and Vanadium Redox Flow Batteries (VRFBs), is offering some uranium producers a potential option for by-product vanadium recovery to improve project economics at a time when uranium prices are low. This paper presents the results of recent optimisation studies on the Bigrlyi deposit for the recovery of both uranium and vanadium. The impact of carbonate leaching conditions on uranium and vanadium extraction from a range of carnotite-in-calcrete ores is also examined, with vanadium extraction limited by the proportion of non-carnotite vanadium present in the ores. The findings are particularly relevant to developing projects as results show that elevated vanadium content in ore does not necessarily equate to a high vanadium extraction in leach.

Jan 1, 2020

By Mary A. Wells, Amir Hadadzadeh, Mark A. Whitney, Stephen F. Corbin

In an effort to produce less expensive titanium sheet via roll compaction, the room temperature compaction behavior of titanium sponge granules (99.9% pure, Alfa Aesar) was studied under uniaxial die compaction. The titanium sponge granules were irregularly shaped, with a high degree of porosity, having a maximum particle size of 3mm. Manual die compaction was conducted using a Carver hand press, in a hardened tool steel die with 12.61 mm inner diameter. Uniaxial die compaction in a hardened tool steel die with 9.50 mm inner diameter was also performed using a Gleeble® 3500 thermal-mechanical simulation testing system which allowed for controlled deformation rates. Compaction behavior of the titanium sponge was studied using well-established compaction equations (Heckel, Panelli-Filho and Ge), and it was observed that compaction rate influences the room temperature compaction behavior of this material. The Heckel analysis of the titanium sponge showed that the behavior of the material could be analyzed in two compaction pressure regimes. In the low pressure regime (<100 MPa) the granules exhibited high compressibility, while; in the high pressure regime (>100 MPa) lower compressibility of the titanium sponge was observed.

Jan 1, 2015

By C. Gosselin, M. Rheault, M. Benoit, Y. Bouroubi, V. Sarago

The last three decades have seen significant mining development in northern regions of Canada, where the freeze and thaw cycle of permafrost and the corresponding surface subsidence and heave represent a significant challenge to the design and maintenance of infrastructures. Identifying areas at risk is of great assistance to reduce the impact of this issue. Over the past ten years, Synthetic Aperture Radar Interferometry (InSAR) has been widely used to monitor ground surface deformation. With this technique, changes in phase between two SAR acquisitions are used to detect centimeter to millimeter surface displacements over a large area and with high spatial resolution. InSAR can be used as a tool to assist the siting and design of new infrastructure as well as highlighting the risk to existing structures in areas of unstable terrain. This paper presents the results of a project carried out by Effigis, which made use of SAR interferometry in the context of monitoring terrain and infrastructure stability in a northern mining environment that is affected by permafrost seasonal and long term changes. TerraSAR-X images acquired during two periods, August to November 2012 and March to October 2013, were used to measure the deformations and/or movement of ground surface, infrastructure and stockpiles caused by seasonal changes in permafrost extent in and around a mining site located in Nunavik, Quebec. The results showed that spatial and temporal distributions of surface displacements are in accordance with scientific and terrain knowledge. Some displacements were observed in loose soil areas while, as expected, none were detected in bedrock and rock outcrop areas. The areas most affected by active layer changes showed surface subsidence in the thaw settlement period. This study confirms that SAR interferometry has a great potential for operational applications related to risks induced by surface deformation in mining environments. It shows that this technique can be used to produce reliable maps of surface movement and monitor the vertical displacement of important infrastructure.

Jan 1, 2015

By D. A. Beck

The load-deformation response of discontinuous rock under static and dynamic loading conditions has been simulated using Explicit Finite Element models. The intent of the analysis was to investigate the effects of specimen size and confining stress on strength, dilation and comminution. The simulations allow the development of homogenised constitutive material properties for discontinuous rock masses using laboratory scale measurements and representative Discrete Fracture Networks (DFNs). A procedure for this is presented which includes a comparison of measured seismic response in a mine to the Dissipated Plastic Energy (DPE) that is released in the simulated rock masses. The models also show how confinement and scale affect the stress-strain and DPE response of the simulated rock specimens, reproducing a number of known rock phenomena that are often poorly captured in geotechnical modelling. A case study is presented showing a satisfactory match between the model-derived, homogenised material properties and values achieved by calibration of a mine-scale model where many thousands of seismic, displacement and damage measurements were available.

May 1, 2009

By Alf Hartling

"Most of the Paleozoic section of the Williston Basin is a thick accumulation of numerous carbonate to evaporite, shallowing upward, cyclic sequences. These sediments were deposited in broad epeiric seas, and the deposition of the evaporite facies marked the final stage of each cycle. Many of the sequences display a pervasive replacement dolomite in the uppermost portion of the carbonate units. This secondary dolomitization is, at least in part, an early diagenetic event, synchronous with evaporite deposition.The inception of evaporite precipitation resulted in the seepage of a dense, Mg-rich brine into the underlying sediment. The heavy brine moved down the gentle regional dip displacing the more normal marine interstitial pore fluid and dotomitized the primary calcitic sediments en route. The supply of Mg-ions decreased away from the source, and correspondingly, the degree of dolomitization decreased and larger crystals formed because of slower nucleation at fewer sites.The seepage refluxion of dolomitizing brines gave rise to the frequently observed textural variation of cryptocrys talline, impervious dolomite grading into a finely sucrosic, permeable dolomite down-dip. This diagenetic facies change provides the critical up-dip barrier for potential hydrocarbon reservoirs. The lateral pool boundaries are controlled by either structural relief or a similar diagenetic facies change. The reservoirs are capped by the tight evaporites.Hydrocarbon production is attained from diagenetic traps in the Mississippian Oungre Zone and the Ordovician Red River &apos;C&apos; Zone . Reservoir creation and the pooling mechanism are the result of dolomitization by the seepage refluxion of dense, Mg-rich brines beneath restricted, hypersaline lagoons. When formulating an exploration/ exploitation program for these oil prone horizons, it is essential to understand the complete geological history in order to establish where the reservoirs will be found and to define the areal extent of each accumulation."

Jan 1, 1984

By F. A. Forward

Introduction The main line of ascent in the development of the nickel industry may be traced back through the International Nickel Company of Canada, Limited, to its earliest antecedents, the Canadian Copper Company and the Orford Copper Company. Mining geology is but one aspect of the overall development of this organization, and the stress it has placed on geology grew according to the need. In the early days, intensive geology was not required because ore supply was not one of the main problems of this or any of the pioneer companies. The difficulty then was to find economic methods for reducing the ores to nickel and copper, and markets for absorbing nickel in the face of a limited demand from consumers heavily prejudiced in favour of the New Caledonia product. "Very early in the history of the region it was patent to everyone that to share in the full benefits of the industry the same individuals or company must control the whole of the operation necessary to manufacture the finished product&apos; (1, p. 45). These conditions were fulfilled for the International Nickel Company in 1902 when the Canadian Copper Company (incorporated 1886), with its ample ore supply, took the initiative to merge its interests with those of the Orford Copper (Refining) Company (incorporated 1887) to form the new company which, with reorganizational changes, emerged as the producer of the overwhelming bulk of the world&apos;s nickel. The Mond Nickel Company, Limited, entered the field in 1899 with a refining process, and over a period of years acquired ore through purchase of mining properties. This Company operated successfully and independently until 1929 when its assets were joined with those of the International Nickel Company in order to permit the most economic exploitation of the Frood-Stobie orebody in which both Companies were interested.

Jan 1, 1948

By F. J. Reichhardt

Abstract -The Molopo Farms Complex is a major, layered ultramafic/mafic, early Proterozoic intrusion which is totally covered by sediments of the Karoo and Kalahari Formations and situated in southern Botswana and northeastern South Africa. The approximately 3000 m thick, generally fine- to medium-grained ultramafic and mafic cumulates are intrusive into equivalents of Transvaal Supergroup sediments and lavas. Multiphase deformation resulted in tilting and segmentation of the Complex into individual tectonic blocks. Sr isotopes document at least two chemically distinct parental liquids which interacted in a complex manner to form an approximately 1000 m thick rhythmically layered succession which straddles the ultramafic/mafic boundary. Repeated mixing resulted in a complex cryptic layering pattern and numerous sulfide-enriched layers which contain significant PGE +Au concentrations.

Jan 1, 1994

By J-g. Cui, X-b. Guo, J-j. Wang, J. Qiao, H. Tian

"Rare earth elements have unique properties because of the special electronic structure. In this paper the improvement of refractory material performance by the light rare earth oxides was introduced. The experiments showed that adding a bit of rare earth oxide could obviously improve the performance of the refractory material. INTRODUCTIONIn recent years, refractory materials are widely applied in the steel smelting process as a ladle lining material. In China, although the total production of fire-proof material exceeds normal demand, but the quality and variety of fire-proof material still have a big gap with world advanced level. A number of refractory products need to be imported from abroad. With the rapid development of domestic steel production, the ladle lining with refractory is gradually running after the world advanced level on production technology, production variety, and quality level. It replaces some imported products meeting the needs of the development of the iron making production. Therefore, there is an important significance to research on solving the problems of the ladle refractory reasonably and avoiding or reducing blind and not proper use of the imported refractory ( Jing, 2007).On the other hand, rare earth oxide has some special excellent properties. Firstly, they are very good refractory materials with their high melting point;Next, they have good resistance to water and alkali resistance function;Thirdly, it is easy for rare earth oxide to generated composite oxide reacting with other metal oxide,achieving the purpose to improving the material properties (Xu, 1978; Diao, 1979). China has a variety of rare earth resources,and rare earth resources is more advantageous in Baotou,taking up about 36 percent of world reserves,which is the world's top of rare earth mineral. In recent years the rare earth products output has risen sharply and many varieties and specifications have appeared. So it is necessary to study the new field of rare earth compound to open up new markets. Thus, it has a very vital significance to promote the further development of rare earth industry, adjust the rare earth products structure, ease the contradiction between supply and demand, and improve refractory products quality and grade in order to better serve the main body production.I In this paper, the experiments are mainly for 210 tons of Al2O3-MgO style series refractory materials belong to ladle lining bag from Baotou Iron & Steel Group Corporation Sheet Factory. The improvement to the effect of refractory material performance is explored by using light rare earth oxides as additives."

Jan 1, 2012

Of the twelve known ore zones on the Sunro property, acquired by Cowichan Copper Co., only the "B" and "C" orebodies of the "River Zone" had been explored sufficiently to indicate the grade and tonnage. The "B" zone was selected for initial production. The portion of this orebody above the main adit level was developed for horizontal-ring, longhole mining. Ore from the stope would be scraped directly to the coarse ore bin. The lack of a suitable mill site on surface, as well as the 8,000-ft. tramming distance, led naturally to the installation ground. I N November, 1960, a lease was obtained by Co-wichan Copper Co. Ltd. (N.P.L.) from Sunro Mines Ltd., covering the main ore (River) zone of the Sunro property. A total of twelve zones had been located on the property. Nine of these lay within the leased area. With the exception of the "B" and "C" orebodies of the River Zone, there had been insufficient exploration for tonnage and grade calculations. Exploration by previous companies had

Jan 1, 1965

By Frank Otten, Jochen Greinacher

"In July 2017, Deilmann-Haniel signed a contract with IOO Slavkaliy to sink two 750 metre (m) deep freeze shafts for the Nezhinsky Potash mine in Belarus. This is the second shaft project where this technology is employed after two over 1,000 m deep shafts for a potash project in Saskatchewan, Canada, have been sunk by the application of the Herrenknecht Shaft Boring Roadheader (SBR) technology. Developed to sink shafts for green field projects in soft to medium hard rock, in frozen or unfrozen geology, the machine technology utilizes a roadheader-type cutterhead on a telescopic boom to mechanically excavate the rock, and a pneumatic mucking system to convey the muck from the face into the buckets. This leads to a manless face during the sinking cycle and thus a significant improvement in terms of workplace safety. For the Nezhinsky project, the SBR design was significantly modified in close cooperation between Deilmann-Haniel and Herrenknecht, based on the available experience and the special requirements of the project. Such modifications have been for example the adaptation of the Pneumatic Mucking System to cope with wet material as well as dry as originally planned or the shaft lining moving from shotcrete application to jump for and tubbing installation for which a step-change hands-off tubbing erector for the placement of segments was designed. Further modifications to optimize the machine technology for the requirements during shaft sinking were applied on the two machines for the Slavkaliy project as well as several revisions to match the special project requirements. The SBR is suitable for soft and medium hard rock up to 100 MPa UCS. The main design limits are maximum weight of the machine with 400 tonnes and length or height of 50 m due to the depth of the pre-sink. The Pneumatic Mucking System was changed in all components, sheaves and rope arrangement were redesigned and the concept of the hoist system was also re-engineered. The SBR in Belarus is configured for a daily sinking rate of three metres and all systems behind the cutting boom are not the bottle neck of the whole system. The works on site started in November 2017 including freeze hole drilling, construction works, site setup, installation of hoists winches, permanent headgears and other components required for sinking. The SBRs arrived on site in June/July 2018 and were preassembled on surface and then lowered into the 50 m pre-sink. SBR #1 started full face sinking in mid-December 2018, and SBR #2 in late January 2019. By the end of February 2019, the machines were at 150 m and 100 m depth respectively, and achieved up to 3.6 m/day concrete lined shaft. The SBR and the sinking system, the experiences, problems, technical solutions and performances of this challenging project will be presented in this paper."

Jan 1, 2019

By P. Mengé

The covering of a hydraulically filled goethite pond is discussed from a geotechnical point of view. The characteristics of the goethite were defined in order to allow a detailed study of the procedure for the construction of the cover on top of the soft material and a verification of the stability of the cover and side slopes after construction. These characteristics and the main results of the studies are given, as well as the experiences and observations made during the execution of the work. Finally, the monitoring plan, during and after construction, is also discussed and some results are given. The &apos;Design and Construct&apos; contract form was used to allow the contractor to choose the optimum and most economical method to realize the closing of the pond, based on his experience with similar projects. The works were carried out between mid 2003 and the end of 2004. The paper will, amongst others, discuss the special method of working that had to be developed to allow the covering of the whole pond in a relatively short time period, without soil improvement methods such as vertical drains or stabilization by in situ treatment. Fill material was used to establish a platform on top of the soft material so that the cover liner and finishing layer could be installed on top of the fill layer. The &apos;floating roof&apos; principle was used; subsidences were allowed to occur during the installation of the impermeable top liner and soil cover.

Jan 1, 2006

By L. H. Cole

FOR many years Industrial Minerals, or as they were formerly called, &apos;the Non-Metallic Minerals&apos;, compared with the metallics, were considered of only minor importance and as such were given scant attention in the technical press as well as in the public press. Those days are, however, happily passing, and thanks, to an appreciable extent, to the constant endeavour of the Industrial Minerals Section of this Institute, established in the fall of 1932 industrial minerals are now assuming the importance to which they are entitled. The term &apos;Industrial Minerals&apos;, when first adopted in this sense by the Institute, was thought to be original in its application, but it is interesting to note that it had been used many years previously by the Queensland Geological Survey in the following publication: SALT Article 1 in Industrial Minerals by B. DUNSTAN, Chief Government Geologist (Publication No. 268, in Part) Queensland Geological Survey, Department of Mines, Brisbane 1920 In Queensland, however, the term embraced some of the metals as well as the non-metallic minerals proper. The lead furnished by Canada in this matter bore rapid fruit, and already the term &apos;Industrial Minerals&apos; is widely used, not only throughout Canada but in the United States as well.

Jan 1, 1939

By Teresa Sikora

For over 40 years the Institute of Innovative Technology EMAG has specialized in the development of systems and equipment for laboratory and on-line monitoring of coal quality parameters, as well as the implementation of these systems and devices in mines and power stations. Some of these systems, based on advanced radiation detection techniques such as ?-ray backscattering (ALFA-06 and ALFA -06/T systems) or dual energy ?-ray transmission measurement (ALFA-06/2E ash meter), and also the ALFA-06/3E system applying microwave technology for the measurement of moisture, have had numerous applications in Poland. At present, over 100 systems and devices are used in Polish hard and brown coal mines. For over 10 years, EMAG has been specializing in the development of systems and devices, based on natural gamma measurement technology. An on-line ash meter, RODOS and RODOS Ex, based on measurement of natural gamma radioactivity of coal, has been developed and put into operation. This technique has been also used in developing the portable ash meter WALKER and laboratory analyzer GAMMA NATURA. The paper briefly presents features of the above-mentioned devices, their limits and their obtained accuracy, but in particular refers to the laboratory analyzer, GAMMA NATURA, as the first such device in the world, and presents the results of ash and moisture content measurement in hard, brown coals and potassium salts. The possible applications and advantages of the device in coal mines are discussed. The paper also presents the implementation results of the portable ash meter, WALKER, and the on-line ash meter, RODOS, that is used underground in coal mines.

Aug 1, 2013

By George Brien, O&apos

The history of the lighting of mine workings dates back to the early part of the 18th century, when small candles known as tallow dips, were used. These were set or held in a lump of wet clay. When looking for gas the flame of. the candle was reduced to a mere glimmer by surrounding the wick below the flame with clay. The candle was then very cautiously raised from the floor toward the roof, the observer screening the brighter portion of the flame with his hand and watching for the first appearance of the pale blue cap above the flame, even at that time, known to indicate the presence of gas. When this appeared the candle was lowered quietly and its flame extinguished before attempting to drive out the gas. A very common and dangerous practice adopted at that time was to get rid of the gas by firing it. This was done by a person selected for his nerve rather than for his caution. Dressed in a? suit of dampened sackcloth or leather, this man well termed a "fireman", would lie prone on the floor of the roadway and light the gas above him by raising his candle fastened to the end of a long stick. If he survived, which was not always the case, he would withdraw promptly to fresh air after the flame had passed over him.

Jan 1, 1924

By Richard W. Hutchinson, Robert W. Hodder

"Pyritic massive sulphide deposits lie conformably above submarine volcanic rocks, and beneath siliceous and manganiferous iron formations. The massive bodies are often zoned, with a barren pyritic top grading downward into pyrite with sphalerite, and occasionally galena, and a chalcopyrite-rich base. They are frequently brecciated, like the lavas beneath them, which contain pyrite and chalcopyrite as coatings on joints and fractures and as dispersed grains. The lavas also exhibit propylitic, argillic and silicic alteration. These sulphide deposits appear to have formed on sea bottom from fluids escaping through the lavas during periods of exhalative and sometimes explosive volcanism. The process may be comparable to the present deposition of base metals from hot brines in the Red Sea. Some porphyry copper deposits resemble the altered, sulphide-impregnated lavas which lie beneath bodies of pyritic massive sulphide. In porphyry copper deposits, pyrite and chalcopyrite occur as veinlets and dispersed grains in intensely fractured tuffs, flows, sub-volcanic intrusions or other host rocks, characterized by propylitic, argillic and silicic alteration. Metal zoning is present; sphalerite and galena often occur in manganiferous veins peripheral to a shell of pyritic veinlets which encloses the mineable zone of chalcopyrite-bearing veinlets. This sulphide distribution appears to have formed from hydrothermal fluids escaping, either passively or violently, from solidifying magma. The fluids may be comparable to hot brines encountered by drilling in the Salton Sea area of California.There are also important differences between massive sulphide and porphyry copper deposits. The former usually occur in differentiated, mafic-to-felsic subaqueous volcanic rocks, whereas porphyry copper deposits are often associated with shallow plutons and subaerial volcanic rocks of intermediate to felsic composition. Calcic-sodic metasomatism accompanies the massive sulphides, whereas potassic metasomatism characterizes the porphyry cop.per deposits. Further, ages of massive sulphides range from Archean (Keewatin) to Tertiary, but porphyry coppers are Triassic to Tertiary in age. These similarities and differences suggest that massive sulphide and porphyry copper deposits are related tectonically and metallogenetically. The former were generated during early stages of crustal evolution, particularly in Archean time, and were repeatedly derived during early stages of younger, individual tectonic cycles. In contrast, the porphyry coppers developed during the later stages of crustal evolution - later in terms of both absolute age and relative age within younger individual tectonic cycles. They appear in younger rocks generally, and specifically in rocks involved in events of the middle and late tectonic stages of orogenic belts. The massive sulphide deposits are of early-magmatic eugeosynclinal affiliation, whereas the porphyry deposits formed in late-magmatic, predominantly subvolcanic settings at the edge of continental plates, where contemporaneous exhalative volcanism was mainly a subaerial phenomenon. Transitional types of deposits exist and are found on continental margins with flanking eugeosynclinal sequences."

Jan 1, 1972

By R. D. Clarke, E. De Souza

"A framework for ventilation planning, with a focus on planning to the end-of-mine life, was developed for the Diavik Diamond Mine, Northwest Territories. This framework was successfully used by Diavik’s mine engineers to select a cost-effective ventilation plan that met the life-of-mine requirements. The framework achieved this result by reconciling the production plan with the ventilation plan. A set of design acceptability criteria was created and a PICK (possible, implement, challenge, kill) chart was used to quickly narrow down the generated ideas for detailed assessment and economic analysis. RÉSUMÉ Un cadre de planification de l’aérage, qui met notamment l’accent sur la planification jusqu’à la fin de vie de la mine, a été développé pour la mine de diamants Diavik. Les ingénieurs miniers de Diavik ont su mettre à profit ce cadre pour sélectionner un plan d’aérage rentable qui répondait aux exigences propres à la durée de vie de la mine. C’est en conciliant le plan de production et le plan d’aérage que cet objectif a pu être atteint. Un ensemble de critères d’acceptabilité de la conception a été créé et un tableau PICK (de l’anglais possible, implement, challenge, kill, une méthode donnant la priorité à certaines actions proposées ou à des idées visant à résoudre des problèmes) a été utilisé pour rapidement limiter les idées générées et les soumettre à une évaluation et une analyse économique détaillées.INTRODUCTION The Diavik Diamond Mine, Northwest Territories, has been an underground-only operation since 2012 and has a remaining mine life of 8 years. In the first year of underground-only operations, the production rate increased from 60 kt of ore per month to more than 160 kt of ore per month. In subsequent years, this rate was continuously increased (Table 1) because the operation went through various improvement initiatives. By the end of 2016, Diavik’s total production was 0.41 Mt (+22.8%) ahead of the 2012 budget for 2016 production."

Jan 1, 2018

By S. K. Dimitrov

?Ellatzite Med? is one of the biggest mining companies in Bulgaria, processing about 12,000,000 t of ore per year. Waste materials left after extraction of copper concentrate are deposited in tailings dam ?Benkovski 2?. The hydraulic structure is built according to the downstream method, through hydrocyclonization where the downstream batter and the body of the wall are formed by the separated coarse sand particles of the separated tailings. In connection with the prolonged concession of Ellatzite Med and the enlarged capacity of Benkovski 2, the tailings dam has expanded on to the surrounding terrain. To guarantee a normal hydrocyclonization and build up of a tailings wall during waste deposition from the ore mill, the technological scheme of the hydraulic transport system of Benkovski 2 has been changed.

Aug 1, 2013

By M. Epiney, A. Ghahreman, R. Kim1and

"Pre-oxidation and cyanide leaching behavior of gold in the presence of sulfide minerals were reviewed, focused on the effects of oxygen injection in the gold leaching process. Generally, pre-oxidation and gold leaching kinetics from iron sulfide refractory minerals, such as pyrite, pyrrhotite, marcasite, pentlandite and arsenopyrite, can be enhanced with higher dissolved oxygen (DO) concentration. However, most of copper sulfide minerals dissolved well both in water and cyanide solutions, and copper from the minerals consumed DO and cyanide to oxidize and leach. Only in the presence of chalcopyrite, gold leaching was effectively occurred with increasing DO. However, chalcocite and covellite severely retarded gold leaching. Stibnite, an antimony mineral, formed a passive film on the gold surface under any DO conditions, and it slowed gold leaching. This impeding effect can be alleviated by leaching at low pH or adding lead salt. Using oxygen and lead together can make synergistic effect in oxidation of sulfide minerals and can enhance gold extraction. Depending on the mineralogical characteristics of the ore, the optimum DO and lead concentrations can be optimized. However, lead can cause environmental problems, and so its dosage should be minimized or eliminated by substituting it with oxygen injection.INTRODUCTIONGold ores containing sulfide minerals are becoming more significant as high grade gold oxide deposits are continuously becoming difficult to find. In light of this situation, to produce more gold, recovery methods from refractory gold ore containing various sulfide minerals should be investigated. Generally, sulfide minerals have impeding effects on gold leaching: formation of a passive film on the gold surface, high consumption of chemicalssuch as cyanide and oxygenduring leaching, reduction of gold cyanide by sulfide ions, etc. (Senanayake, 2008). Therefore, sulfides must be properly treated for better gold recovery. Pre-oxidation of sulfide minerals by injecting pure oxygen can decrease the impeding effects in gold leaching. Prior to cyanidation, sulfide minerals can be oxidized to metal hydroxide and sulfate form, which consume negligible cyanide in the following cyanidation circuit (Bodnaras et al., 1993). Moreover, gold cyanidation can be enhanced by increasing concentration of the dissolved oxygen (DO). In general, the optimum concentration ratio of [CN-]/[O2] is calculated as 6, but it goes higher in the real system (Marsden &House, 2006), which means that the reaction is typically controlled by DO concentration."

Jan 1, 2017

By V. W. Shtenko, B. J. Ennis, P. H. Bridge

"The northeastern region of British Columbia contains large quantities of high-quality metallurgical coal. To market the coal, it was necessary to provide the required infrastructure which included rail access. This paper presents the role of the British Columbia Railway in the northeast coal development.In 1976, B.C. Railway undertook to study two main routes, one originating at Chetwynd and the other at Anzac, both located on the main line, north of Prince George. The routes studied are briefly described, detailing the methodology and engineering analysis carried out to permit the selection of a single route that would be the most cost effective, taking into consideration the construction, maintenance and operating costs. The operating parameters, track and grade standards, anticipated tonnage, construction costs and the final route selected are also presented.Pre-engineering analysis and studies of the route selected originating at Anzac, known as Tumbler Ridge Branch Line, and which commenced in 1977, were concluded in 1978. New mapping was developed to a scale of 1:2000 with good vertical and horizontal control. Based on the mapping data, terrain analysis, and designs developed, an estimate of construction costs and schedule of work was developed.Authority to proceed with the final design and construction was provided in December 1980, with the first shipment scheduled for December I, 1983. Final designs of all structures are discussed, including schedules, cost to completion, and control systems utilized. The decision to electrify the Tumbler Ridge Branch Line and related topics are discussed, with a brief description of train operations. The present status of the project is also presented."

Jan 1, 1983

"Virtual reality, a 3D computer-generated environment, has become a recognized delivery system for many forms of education. This paper describes the application of virtual reality to mineral processing education. An interactive mineral processing visualization module developed at the University of New South Wales, Australia, provides users with an overview of a base-metal concentrator and details about how the mined ore progresses through stages in processing. The module also involves developing instructional based plant layouts and flowsheets in the virtual environment. These assist the user in understanding the essential components of the base-metal concentrator.RÉSUMÉ La réalité virtuelle (RV), un environnement en 3D généré par ordinateur, est devenue un système de prestation reconnu pour diverses formes d’éducation. Cet article décrit l’application de la réalité virtuelle à l’éducation dans le domaine de la minéralurgie. Un module interactif de visualisation du traitement des minerais développé par l’université de Nouvelle-Galles du Sud, en Australie, offre aux utilisateurs une vision d’ensemble d’un concentrateur de métaux communs ainsi que des détails concernant la progression du minerai extrait à travers les différentes étapes de traitement. Ce module implique également le développement de schémas de réalisation et de traitement didactiques dans l’environnement virtuel, lesquels schémas aident les utilisateurs à appréhender les composantes essentielles d’un concentrateur de métaux communsINTRODUCTIONVirtual reality (VR) is the creation of an artificial environment that is experienced through sights and sounds provided by a computer (Squelch, 2001). The simulated environment is achieved through technologies such as 3D graphics, audio feedback, and special peripheral devices to produce interactive environments.Virtual reality has been used in diverse fields including medicine (Riener & Harder, 2012), entertainment (Hsu, 2011), military (Manojlovich, Prasithsangaree, Hughes, Chen, & Lewis, 2003), manufacturing (Zimmermann, 2008; Jiang, 2011), and chemical processing (Squires, Andersen, Reklaitis, Jayakumar, & Carmichael, 1992; Schofield, Lester, & Wilson, 2005). Virtual reality is also becoming the recognized delivery system for education in many fields, including engineering (Bell & Fogler, 1996, 1998; Shin, 2002). For example, VR laboratories have been designed and developed to teach users fundamental features of heterogeneous catalytic mechanisms and absorption columns (Bell & Fogler, 1995), the multi-phase and multi-component blast furnace iron-making process (Babich & Senk, 2009), and to guide users to identify various safety measures while working in a real laboratory (Bell & Fogler, 1996)."

Jan 1, 2017