Search Documents

By Hugh P. Godard, K. Winslow

"AbstractA number of panels of various aluminum alloys in different combinations and secured by steel and three types of aluminum rivets were exposed underground at two locations in a Northern Ontario gold mine for two years and then examined to determine the extent of corrosion. The results indicate Alcan 65S-T to possess considerable advantages over Alcan 178-T, which has been employed in the construction of light skips and cages with considerable success for almost twenty years. Information on the behaviour of these alloys when used with steel rivets and in mixed combinations with themselves was obtained.IntroductionBy the complete substitution of aluminum alloys for steel in the fabrication of mining skips and cages, their weight can be reduced as much as 50 per cent. Lesser savings are possible though its savings are possible through its plates, doors, reinforcing members, etc. Reduced weight leads to economy through increased hoisting efficiency.For a new installation, the basis of design is the rate of production, which thus fixes the live load to be hoisted per trip. A lighter skip permits the use of a lighter rope and a smaller hoist. In deep shafts with high-speed hoists operated in balance, the power required for accelerating is considerable. The hoist size is determined by the weight of skip, load, and rope plus the force required to accelerate or decelerate these three elements A light skip may result in a considerably lighter rope. This is important because, even though the skip can be completely balanced this is not true of the rope. Partial balancing is possible, but conical hoist drums or other devices for this purpose are costly; thus a smaller rope results in a smaller hoist, with consequent general reduction in cost of the whole installation. A reduction in power consumption is also obtained as a result of keeping to a minimum the amount of unbalanced load and the weight of all moving parts which must be accelerated."

Jan 1, 1950

By J. P. Dick

THIS paper is a description of the milling practice and metallurgy at the Moneta Porcupine mine, Timmins, Ontario. The results obtained with an all-cyanide circuit and later with flotation followed by cyanidation are described. The ?investigation which prompted the various changes in milling practice have also been dealt with. Moneta ore is possibly the most refractory now being milled in the Porcupine district. This is due to the ultra fine state in which the gold occurs and to its intimate association with pyrite. No doubt there is ore of similar characteristics on the neighbouring properties but it probably forms only a small portion of the tonnage being mined, whereas at Moneta the bulk of the ore requires an extremely fine grind to liberate the gold. The fineness to which an ore can be ground economically has gone far beyond what was thought to be the limit only a few years ago. Formerly, a set of standard screens was all that was required to measure the fineness to which an ore was ground. At present, the Haultain infrasizer is practically indispensable, and the nominal micron has become a familiar unit of measurement to all those dealing with the problems of fine grinding.

Jan 1, 1941

By R. J. Hundermark, K. van der Merwe, L. R. Nelson

Taphole integrity is critical to all furnaces, but it is especially important in high intensity electric furnaces processing matte and metal of high superheat. Key furnace dimensions are the electrode proximity to the taphole, hearth sump below the taphole and the shape and location of the taphole in the furnace wall (e.g., circular versus rectangular furnace). In addition, electric furnace power density needs to be matched appropriately to any configuration to achieve operational reliability and furnace integrity. The role of furnace dimensioning is generically reviewed across many pyrometallurgical processes to explore potential impact on furnace taphole performance. Some empirical furnace dimensions and power density ratios of industrial furnaces are then compared to explore to what extent they may indeed influence taphole integrity.

Jan 1, 2015

By R. E. Gilmore

PREAMBLE THIS PAPER comprises material presented in two separate 'Papers at the British Commonwealth Scientific Specialist Conference on Fuel Research held in London, England, in July, 1950. These papers are now available for publication in Canada, since only essential parts of the conference discussions, in addition to the resolutions resulting therefrom, will be published in the official Proceedings of the Conference. Inasmuch as the information presented concerns Canadian organizations and training facilities for fuel research, it should be of general interest to Canadian scientists, and especially to the Coal Division of the Canadian Institute of Mining and Metallurgy. Part I, the alternate title of which is Facilities in Canada for Fuel Research and for Exchange of Information and Staff, does not include research on peat, oil shale, petroleum oils in general, and natural gas, and omits studies of the geology, constitution, and production of coal. Special reference is, however, made to research on the heavy crude oils and bitumen of the Western Prairie Provinces, and particularly to their production and treatment to produce crudes for oil refinery processing.

Jan 1, 1951

By M. R. Hudec, M. A. Nikolinakou, P. B. Flemings

"We model the shale response to the large deformations associated with salt bodies, and we identify the implications of the stress changes for hydrocarbon exploration. We employ both the static and evolutionary approach, and show that while the static one can model actual geologic geometries, only the evolutionary approach can provide a detailed description of the stress history of shales, which is essential for predicting stress, porosity, and pore pressure and, more generally, for understanding Earth processes related to salt-hydrocarbon systems.INTRODUCTIONDuring the last two decades, understanding the stress, material behavior, and pore pressure in shales around salt bodies has become increasingly important. The energy industry routinely drills near salt (Beltrão, Sombra, Lage, Fagundes Netto, & Henriques, 2009; Meyer, Zarra, Rains, Meltz, & Hall, 2005; Seymour, Rae, Peden, & Ormston, 1993), because a significant number of hydrocarbon reservoirs around the world are found in layers dipping away from salt diapirs.Salt is a viscous material that cannot sustain deviatoric stresses. Under differential loading it flows, changes shape, and eventually relaxes to an isostatic stress state (Urai & Spiers, 2007). Therefore, emplacement of a salt body and its viscous relaxation process may cause significant deformation of the surrounding sediments, perturb their state of stress and create local overpressures (Dusseault, Maury, Sanfilippo, & Santarelli, 2004; Seymour et al., 1993). As a result, drilling near salt is particularly challenging, and problems leading to additional expense or even abandonment are common (Bradley, 1978; Dusseault et al., 2004; Meyer et al., 2005; Seymour et al., 1993; Willson et al., 2003).Historically, salt and the evolution of its cross section to the present day geometry have been studied using kinematic restorations (Rowan & Ratliff, 2012). This approach aims to explain the present geologic section through a sequence of plausible past sections; however, it does not model the constitutive response of the wall rocks, hence it cannot provide any prediction on their state of stress. Similarly, largestrain numerical studies (Albertz & Beaumont, 2010; Chemia, Schmeling, & Koyi, 2009; Goteti, Ings, & Beaumont, 2012; Gradmann, Beaumont, & Albertz, 2009) have focused on the rheological evolution of salt systems without modeling the geomechanical response of the sediments."

Jan 1, 2015

By Willem P. C. Duyvesteyn

"Scandium International Mining Corp (SCY) has been involved in the commercial development of its Nyngan Scandium Project for about ten years. Various studies at a variety of global R&D organizations have been carried out in an attempt to define the deportment of scandium in both the limonite as well as the saprolite phases of Nyngan ore to assist with process development. Technologies such as sulfuric acid baking, high pressure acid leaching, sulfuric and hydrochloric acid atmospheric leaching and heap leaching have been extensively investigated both at the bench and pilot scale level to arrive at the most economic process flow sheet that will be discussed in some detail in this paper. Solvent extraction, ion exchange and other refining technologies have been tested and an optimum configuration has been established for the Nyngan project which is expected to be the first primary scandium mine and metallurgical plant in the world.Because of a lack of product availability the current scandium market is limited to less than 20 tons per year. Technologies have been identified to produce product with different specifications for aluminum alloys and solid oxide fuel cell applications. Preliminary economics have identified that Nyngan will be a robust and low capital cost project that can readily be expanded as the size of the scandium market increases."

Jan 1, 2016

By J. Gao, H. O. Gekonde, S. V. Subramanian

"The functional role of inclusions at low cutting speeds is to promote ductile fracture in chip formation process, whereas the role of inclusions at high cutting speeds is to prevent tool crater wear by suppressing the tribological phenomenon of seizure at the tool-chip interface. Glassy oxide inclusions are engineered into the workpiece to form a viscous layer in-situ at the tool-chip interface at high cutting speeds. The viscous layer lubricates the tool-chip interface to prevent the seizure. In comparison with the large volume fraction of inclusions needed for promoting ductile fracture at low cutting speeds, the amount of inclusions required for lubricating the toolchip interface at high cutting speeds is very small and is in the range that is typical of clean steels. The chip fracture process at high cutting speeds is aided by strain rate hardening of the matrix, which facilitates chip disposal of relatively clean steel.Inclusion engineering for high speed machining involves the control of the rheology and composition of inclusions to meet target viscosity at the tool-chip interface. The application of thermodynamic models in controlled production of inclusions in steels designed for high speed machining is discussed."

Jan 1, 1998

By David Berberick

"Hecla Limited’s No. 4 Shaft at the Lucky Friday Mine is the largest capital expenditure in the corporation’s 128-year history and is considered the deepest shaft in the United States. This paper will discuss the project’s history and lessons learned from the initial conceptual design work in 2007 through project commissioning in 2017. Change management was key for the owner, contractors, and vendors in delivering the operational and organizational success on the project. The No. 4 Shaft has extended the life of the Lucky Friday Mine by 21 years to 2039. INTRODUCTION The Lucky Friday Mine of Hecla Mining Company (Figure 1) is the oldest active (77 years) and deepest mine in the Coeur d’Alene mining district, producing approximately 725 tonnes (800 tons) per day from narrow, vertical, silver, lead, and zinc veins. Primary access into the mine is via the Silver Shaft, a 5.5-m (18-ft) diameter, concrete lined shaft sunk to an original depth of 1,890-m (6,200-ft). Current production is from the Gold Hunter vein system, approximately 1,525-m (5,000-ft) northwest of the Silver Shaft.Cut and fill stoping is currently employed at depths to 2.3 km (7,500 ft) below ground surface, making it one of the deepest mines in the western hemisphere. No. 4 Shaft is a 5.5-metre (18-foot) diameter, concrete lined circular shaft, constructed as a 1.2 km (3,860 feet) deep winze in the Lucky Friday Mine. The 2.4 m (8 ft.) diameter, double drum, double clutch, Siemag hoist and associated headworks are situated at the 4760 level, top station at 4940 and shaft stations at 5900, 6500, 6580, 7500, 7580, 8300, 8380, 8500, and 8620. Shaft stations reference depth below Silver Shaft top station. The 4 Shaft was designed, constructed and commissioned over ten years, between 2007 and 2017. Basic design work was completed by Nordmin Engineering, followed by detailed design completed by Cementation Canada. Shaft construction was awarded to Cementation USA and lateral development was initiated in early 2008. Over the course of the next nine years, the project was suspended and restarted twice, dealt with the loss of a miner, added scope including shaft depth and mine infrastructure facilities, experienced squeezing ground that required liner replacement, changed excavation section, and dealt with a final alignment that was not within design requirement for verticality. Hecla and Cementation were successful in delivering a facility that provides fully functional access from collar at 4940 level to shaft bottom at the 8620 level. Two active mining levels below the collar, 5900 and 6500 are accessed. In addition, the shaft provides access to the future mining level at 7500, skip loading facility at 7580 level, station and loading pocket cutouts at 8300 and 8380 levels, spill pocket at 8500 level, and shaft bottom pumping facility at 8620 level (Figure 2)."

Jan 1, 2019

By Emilie Williams

Introduction Mouska Mine, Doyon Division site Background and timeline Obstacles to standard paste delivery system Components of Mouska paste system Technical considerations Operational considerations Mouska Mine Underground gold mine 30 km east of Rouyn-Noranda, Quebec Part of Doyon Division, 100% owned by IAMGold Commercial production since 1991 Cumulative production over 850,000 oz Conventional mining until 2009 485 m shaft from surface 560 m internal shaft 500 tpd (ore and waste) Off-site milling Approximately 150 employees

Oct 1, 2010

By C. Blawert

In previous studies of various HPDC magnesium alloys we found that the corrosion properties of the skin are inferior in comparison to the bulk, However, this is surprising as one would expect better corrosion properties for the finer microstructure of the skin, In a more detailed study using 2 and 6 mm thick sections from HPDC AZ91 step plates, the corrosion results of the original skin, the slightly removed skin and the bulk were compared, Indeed, the corrosion measurements including potentiodynamic polarization, long term polarization resistance measurements and electrochemical impedance spectroscopy (EIS) revealed a lower corrosion resistance of the original as-cast skin. An explanation for this corrosion behavior was found, on the one hand, in the microstructure concerning especially the amount and distribution of the 13-phase and, on the other hand, in the composition, including the distribution of the most important alloying element Al and of some impurities such as Fe.

Jan 1, 2005

By J. G. Ross

IN the paper entitled Block Caving at the King Mine (1), which was presented at the Annual General Meeting held in April, 1934, at Quebec, it was pointed out that, owing to certain conditions and financial restrictions, it was advisable to provide a temporary shaft. This was raised from the )00-ft. level to the bottom of the pit, and a 45-degree incline track was constructed up the face of the pit to surface. The temporary shaft and incline were within the ore-body, but were to be used only until such time as the new shaft-the subject of this paper-could be sunk and made ready for operation. After a careful study had been made of all available information pertaining to the ore-body, including examination of diamond-drill core records and geological data, a shaft location was selected well outside the ore-body. Further, since the crusher and dryer buildings are located over part of the ore-body, it was necessary to plan the removal of these buildings and to construct a new crushing and drying plant. This, and the new shaft, must operate in conjunction with the present mill and rock storage bin, which would continue robe used as formerly. No part of this programme, with the exception of drifting toward the shaft site, was started prior to 1937. More than usual detail on technical features is given in this paper in the hope that some parts of it may be of assistance to other members of the Institute who have to undertake somewhat similar work. The engineering and operating staff designed and supervised the work, while at the same time carrying on regular production in four mines at the rate of 12,000 tons of rock mined per day, the output at the King mine being at the rate of 140 tons per hour. No additional engineers were required.

Jan 1, 1939

By N. Bédard

"This paper highlights Cambior’s initial approach for recruiting and retaining its international employees, the importance of proper preparation and the support needed to ensure a competent and stable workforce.In general, most of the training and information available for human resources personnel prepares the specialist for handling various aspects of labour relations, recruitment and hiring, benefits administration, employee relocation, etc. This is usually done in a Canadian context.Only recently, has more specialized training been developed to prepare human resources practitioners for the complex issues related to expatriate employees and dealing with human resources issues in other countries"

Jan 1, 2004

By Cedric E. Gregory

"A study of model rectangular mine shafts has been made in the wind tunnel, with the aim of reducing air-flow resistance elements to a practicable minimum. An analysis of Table 7 shows an indicated average decrease in resistance of 28 per cent by adopting the over-all modifications involved in the configurations actually tested. Much greater reductions (up to 68 per cent) are indicated by extrapolating beyond the test results directly achieved. Intermediate partial reductions in aerodynamic resistance are shown for individual modifications, such as: (1) about 3 per cent for locating the lagging in the No. 4 (inside flush) position as against the No. 1 position - 8 per cent as against the No. 2 position - and 23 per cent as compared with position No. 3; (2) about 12 per cent for using lagging instead of steel meshwork along the divider separating the skipway from the service compartment; (3) about 14 per cent for using steel gridwork ladder stagings at 3-set intervals instead of similarly spaced wooden stagings; (4) about 12 per cent for using steel gridwork ladder stagings at 3-set instead of at 1-set intervals; (5) about 13 per cent for fitting a streamlined fairing (see Fig. 5) to the upstream face of the skipway divider. Contrary to expectations, an advantage of only 3 per cent is indicated for lagging in the inside flush (No. 4) position over the outside position (No. 1). This slight gain does not appear to warrant the cost of moving the lagging. However, if the lagging is already in the No. 2 or No. 3 position, there is an 8 and 23 per cent advantage respectively."

Jan 1, 1973

By H. Hejny

Economy needs mineral raw materials in almost each sector of modern life. They can only be provided by mining activities. An increasing share of the total mining production will be by underground mining. The mineral deposits will be found at gradually greater depths, including all problems associated with them. It involves an increase in overburden pressure with subsequent rock stability problems and risks of structural collapse. There is a need for new and safe technologies for almost all parts of a modern mine. The mining industry faces a number of challenges which require technical solutions that encompass the entire network and include the economic, social and environmental issues. The industry needs a new image based on pioneering solutions and a modern structure that can exploit minerals at greater depths and promote both high productivity and safe working conditions. Funding has been secured from the European Commission for the I²Mine project. Work started in November, 2011. This initiative is designed to focus on the technological challenges that the mining industry is currently facing including the exploitation of ever deeper deposits and the aspiration for an invisible, safe, zero impact mine. The project comprises a consortium of 27 organisations from 10 European countries. I²Mine marks the start of a series of development activities aimed at realising the concept of an invisible, zero impact, deep mine. The extractive sector, still seen as being old fashioned and environmentally unfriendly, will show that mineral extraction and processing can be done in a highly innovative and sustainable manner with low impact underground and zero impact above ground. The concept of I²Mine is to develop innovative methods, technologies, machines and equipment necessary for the efficient exploitation of minerals and disposal of waste, all of which will be carried out underground. This will dramatically reduce the volume of surface transportation of both minerals and waste, minimising above ground installations and reducing the environmental impact. New eco-efficient technologies will be applied in order to make the entire mining process more efficient and environmentally sound. The concept is for an integrated mine, with the majority of the installations underground, and only the final product will be transported above ground to be shipped to the customer. Production waste will be treated and stored underground and gaseous emissions will be managed underground as far as practical. I²Mine will also focus on ideas and concepts that increase energy efficiency and decrease waste. The core of the project will be to develop breakthrough technologies for autonomous, highly selective, continuous mineral extraction processes and machinery based on new sensor technologies, face front separation as well as innovative concepts for mass flow management and transportation integrating state of the art technologies. The concept of an invisible, zero impact mine requires a refined process underground that selectively extracts the mineral thereby reducing waste. For this reason, improved extraction machines and near to face processing methods, including backfill procedures, need to be developed. These developments include rock mechanics and ground control solutions, incorporating health, safety and environmental issues.

Aug 1, 2013

By Youjun Tao

Falcon centrifugal gravity separation tests were conducted to study desulfurization and de-ashing performance with different size fractions of a high-sulfur Chinese -0.5mm fine coal in a dense medium. Performance indicators such as combustible recovery, ash and sulfur rejection, and desulfurization efficiency were used to evaluate the separation efficiency. The results show that for -0.5 mm coal particles, all performance indicators except ash rejection are higher for the Falcon concentrator than for flotation. More specifically, for the +0.125 mm size fraction, Falcon centrifugal separation produced better ash and sulfur rejection performance than froth flotation. However, the Falcon concentrator also showed higher combustible recovery but lower ash and sulfur rejection than froth flotation for the -0.125 mm size fraction.

Aug 1, 2013

By Jason J. Ballentine

This case study presents the results of a maintenance review of a soot blower system at a coal fired power generation station. The power generation station was following a ?repair when it breaks? maintenance strategy for its soot blowers. The efficiency losses incurred as a result of failures in the soot blower system and the resulting interruption and out of service time was found to have a significant effect on the plant output. The maintenance strategy for the soot blowers was reviewed using Reliability Cantered Maintenance and lifecycle simulation. This methodology provided visibility to the monetary implications of failures and allowed alternative types of maintenance to be assessed and where justified were added to a maintenance schedule in the Maximo work order management system. By reducing unplanned breakdowns the predicted reduction in efficiency losses was 45%.

May 1, 2007

By F. H. Edmunds

I N presenting this paper, the writer wishes to point out some of the difficulties and problems of geological work in that part of Saskatchewan in which outcrops are few. These problems are well known to all geologists who have made investigations in this region, but may not be so well known to those outside. A table of the strata as known in certain areas of Saskatchewan and the adjacent provinces is given, with a brief discussion of some of the formations and beds about which there is little knowledge due to their being deeply buried and not exposed in the region. Comment with regard to possible oil and gas structures is made and some features of the structures in the Battleford and Simpson districts are described. The writer wishes to make acknowledgment to members of the Geological Survey of Canada to whose work in Saskatchewan and the adjacent provinces reference is made, and to others who have made, or are making, valuable contributions to the stratigraphy of Saskatchewan. Mr. G. C. Webb has kindly furnished information regarding and materials taken from a well bored recently in the Paynton district. Special thanks are due to the Simpson Oil and Gas Company for permission to use much valuable information with regard to their wells and for the generous way in which the officials and staff co-operated with the writer. The opportunities the writer has had to visit many parts of the Province have been in connection with investigations for the Provincial Department of Natural Resources and through facilities provided by the Department of Soils of the University of Saskatchewan. To these Departments the writer accords his thanks. For the purposes of this discussion, Central Saskatchewan may be considered as that portion of the Province extending from Township 16, with Regina, Moose Jaw, and Swift Current situated on or near the southern boundary, to Township 48, with Prince Albert and Lloydminster on the northern boundary. This region includes territory underlain by Cretaceous sediments and excludes the southern portion of the Province, where Tertiary beds underlie the surface and are exposed to an extent sufficient to permit a measure of systematic mapping.

Jan 1, 1937

By W. A. Lang

Introduction Under our present civilization, industrial developments will be greatest in those areas in which energy .can be most economically produced and efficiently used, where labour is in adequate supply, and where markets for the products of industry are available. A knowledge of fuels- the present major sources of energy- and of their utilization is therefore of vital importance. With that in mind, the aim in this paper will be to outline the known reserves of fuels in Alberta, to give their characteristics, to indicate the markets served by each, and to offer some suggestions for the future development of the coal industry. The paper should be regarded as a compilation of published data rather than as an original treatise. Alberta is richly blessed by having large reserves of mineral fuels. The estimated reserves of coal are 46,562 million tons. Alberta is the oil and gas province of Canada. The world's largest deposit of bituminous sand occurs along the Athabaska river in Alberta. In addition, there are large areas of forested land in the northern and western sections of the Province, and the rivers serve for the development of hydro-power.

Jan 1, 1949

By F. D. Aaring

"IntroductionTHE PINCHER CREEK gas condensate field, in Township 3, Range 28, and Townships 3 and 4, Range 29, West of the Fourth Meridian, was discovered in 1947 by the Canadian Gulf Oil Company with the completion of Pincher Creek No. 1 well in the Madison lime-stone of Mississippian age.This discovery was the result of a great deal of detailed seismic work in the area and is a credit to the geophysical personnel of the Company. The depth of the reservoir varies from 7,400 feet to 8,200 feet subsea, with the established water level at -8,200 feet. The predicted depth was but a scant 100 feet from that found in the discovery well, at 11, 705 feet. Since the discovery of the reservoir, three additional wells have penetrated the Madison limestone and have further verified the original •seismic interpretation of the limits of this reservoir.To date, •only a very small amount of gas has been produced from this field. Consequently, the reservoir studies that have been made so far are predominantly based on investigations of the phase behaviour of the fluid and physical characteristics of the reservoir rock. In view of the above limitations, it has been necessary to set up and perform model reservoir studies with the fluids and to recover as much core from the productive Madison limestone as possible in order that it might be analysed by conventional laboratory technique and be subjected to detailed microscopic geological examination."

Jan 1, 1952

By G. M. Card, K. D. Card, B. V. Sanford

Abstract-The Canadian Shield and its extensions are traversed by an orthogonal system of northwest and northeast trending arch-style uplifts. These basement arches were formed by repeated vertical movements along pre-existing structures during compressional and extensional tectonism connected with events in surrounding Proterozoic and Phanerozoic orogens and ocean basins. The arches influenced patterns of sedimentation and tectonism in the intervening epicratonic basins and marginal platforms throughout the Proterozoic and Phanerozoic. Movements on the arch structures also triggered minor magmatism and controlled the location and timing of alkalic rock-carbonatite, kimberlite, and related intrusions in the Canadian Shield, the Western Canada Sedimentary Basin, and West Greenland.

Jan 1, 1997